-
1 Semi-Insulating Polycrystalline Silicon
microel. SIPOSУниверсальный русско-немецкий словарь > Semi-Insulating Polycrystalline Silicon
-
2 расстояние утечки
расстояние утечки
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание. Стык между двумя элементами из изоляционного материала считают частью поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
расстояние утечки (см. приложение В)
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание — При определении расстояния утечки относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9
[ ГОСТ Р 50345-99( МЭК 60898-95)]
расстояние утечки по поверхности
-
[IEV number 151-15-50]
путь утечки
Кратчайшее расстояние вдоль поверхности изоляции между двумя проводящими частями или между проводящей частью и доступной поверхностью.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - A joint between two pieces of insulating material is considered part of the surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - For the purpose of determining a creepage distance to accessible parts, the accessible surface of an insulating enclosure is considered conductive as if it was covered by a metal foil wherever it can be touched by a hand or a standard test finger according to figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
creepage distance
shortest distance along the surface of insulation between two conductive parts or between a conductive part and the accessible surface
[IEC 60335-1, ed. 4.0 (2001-05)]
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts
[IEV number 151-15-50]FR
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Un joint entre deux portions de matière isolante est considéré comme faisant partie de la surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Pour la détermination d'une ligne de fuite pour des parties accessibles, la surface accessible d'une enveloppe isolante est considérée comme conductrice comme si elle était recouverte d'une feuille métallique à tout endroit où elle peut être touchée par la main ou par le doigt d'essai normalisé conforme à la figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
ligne de fuite
plus petite distance le long de la surface de l’isolation entre deux parties conductrices ou entre une partie conductrice et la surface accessible
[IEC 60335-1, ed. 4.0 (2001-05)]
ligne de fuite, f
distance la plus courte, le long de la surface d'un isolant solide, entre deux parties conductrices
[IEV number 151-15-50]1) Должно быть проводящими
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > расстояние утечки
-
3 ввод с бумажно-масляной изоляцией
ввод с бумажно-масляной изоляцией
Ввод, в котором основная изоляция состоит из бумаги, пропитанной изоляционной жидкостью.
Примечание. Бумага, в основном, пропитывается трансформаторным маслом.
[ ГОСТ 27744-88]EN
oil-impregnated paper bushing
OIP
bushing in which the major insulation consists of a core wound from paper and subsequently treated and impregnated with an insulating liquid, generally transformer oil
NOTE The core is contained in an insulating envelope, the space between the core and the insulating envelope being filled with the same insulating liquid as that used for impregnation.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée en papier imprégnée d'huile
OIP (oil-impregnated paper)
traversée dont l'isolation principale est assurée par un corps enroulé en papier ultérieurement traité et imprégné d'un liquide isolant, généralement d'huile de transformateur
NOTE Le corps est placé dans une enveloppe isolante, l'espace entre le corps et l'enveloppe isolante étant rempli du même liquide isolant que celui employé pour l'imprégnation
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
DE
FR
- OIP
- traversée en papier imprégné d’huile
Русско-немецкий словарь нормативно-технической терминологии > ввод с бумажно-масляной изоляцией
-
4 проходной изолятор
проходной изолятор
Изолятор, предназначенный для провода токоведущих элементов через стенку, имеющую другой электрический потенциал.
[ ГОСТ 27744-88]
проходной изолятор
-
[IEV number 151-15-40]EN
(insulating) bushing
insulator forming a passage for a conductor through a non-insulating partition
[IEV number 151-15-40]
bushing
A bushing is a cyclindrical insulating component, usually made of ceramic, that houses a conductor. It enables a conductor to pass through a grounded enclosure, such as a transformer tank (the physical shell of a transformer), a wall or other physical barrier, to connect electrical installations. In the case of a transformer, bushings protect the conductors that connect a transformer’s core to the power system it serves through channels in the transformer’s housing.
[ABB. Glossary of technical terms. 2010]FR
isolateur de traversée, m
traversée, f
isolateur permettant le passage d'un conducteur à travers une paroi non isolante
[IEV number 151-15-40]
Проходной изоляторПараллельные тексты EN-RU
The circuit breaker is connected via bushings to the rest of the switchgear at the flanges provided.
[Siemens]С другими частями распределительного устройства силовой выключатель соединяется через проходные изоляторы, закрепленные в его фланцах.
[Перевод Интент]Тематики
Классификация
>>>Обобщающие термины
EN
DE
FR
- isolateur de traversée, m
- traversée
Русско-немецкий словарь нормативно-технической терминологии > проходной изолятор
-
5 изоляция
fFRA isolant mDEU Isolierung fENG insulationITA isolante mPLN izolacja fRUS изоляция fсм. поз. 929 на,,
,
FRA produit m isolantDEU Isolierung fITA materiale m isolantePLN izolacja fRUS изоляция fсм. поз. 2267 на,FRA enveloppe f calorifugeDEU Wärmeschutzmatte fITA rivestimento m isolantePLN otulina fRUS изоляция fсм. поз. 2312 на—FRA revêtement m de wagon réfrigérantDEU Isolierungsaufbau m des KühlwagensITA rivestimento m di carro refrigerantePLN izolacja f wagonu chłodniRUS изоляция f вагона-холодильникасм. поз. 1015 на—FRA calorifugeage m de gaineDEU Wärmeisolierung f für LuftkanalITA isolamento m del condottoPLN izolacja f cieplna przewodu powietrznegoRUS изоляция f воздухопроводасм. поз. 2420 на—FRA enveloppe f calorifuge du collecteurDEU Isolierung f für LuftsammlerITA rivestimento m isolante del collettorePLN otulina f komory powietrznejRUS изоляция f воздухосборникасм. поз. 2415 на—FRA bande f isolanteDEU Zwischenlage f, plastischeENG lining, plasticITA nastro m isolantePLN izolacja f z materiału plastycznegoRUS изоляция f обвязочного брусасм. поз. 1001 на—FRA calorifugeage m de conduite generale de vapeurDEU Wärmeisolierung f für HauptdampfleitungITA isolamento m della condotta generale del vaporePLN izolacja f cieplna przewodu parowegoRUS изоляция f паропроводасм. поз. 2421 наизоляция паропровода воздухоподогревателя
—FRA calorifugeage m de conduiteDEU Wärmeisolierung f für LeitungITA isolamento m della condottaPLN izolacja f przewodu parowego nagrzewnicyRUS изоляция f паропровода воздухоподогревателясм. поз. 2425 наизоляция, тепловая
—FRA enveloppe f calorifugeDEU Platte f aus IsolierstoffITA rivestimento m isolantePLN otulina f, izolacja fRUS изоляция f, тепловаясм. поз. 2411 на -
6 ввод с бумажной изоляцией, пропитанной смолой
ввод с бумажной изоляцией, пропитанной смолой
Ввод, в котором основная изоляция состоит из бумаги, пропитанной смолой.
[ ГОСТ 27744-88]EN
resin-impregnated paper bushing
RIP
bushing in which the major insulation consists of a core wound from untreated paper and subsequently impregnated with a curable resin
NOTE A resin-impregnated paper bushing can be provided with an insulating envelope, in which case the intervening space can be filled with an insulating liquid or another insulating medium.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée en papier imprégné de résine
RIP (resin-impregnated paper)
traversée dont l'isolation principale est assurée par un corps enroulé en papier non traité et ensuite imprégné de résine durcissable
NOTE Une traversée en papier imprégné de résine peut comporter une enveloppe isolante. Dans ce cas, l'espace intermédiaire peut être rempli d'un isolant liquide ou d'un autre milieu isolant
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > ввод с бумажной изоляцией, пропитанной смолой
-
7 ввод с бумажной изоляцией, склеенной смолой
ввод с бумажной изоляцией, склеенной смолой
Ввод, в котором основная изоляция состоит из бумаги, склеенной смолой.
[ ГОСТ 27744-88]EN
resin-bonded paper bushing
RBP
bushing in which the major insulation consists of a core wound from resin-coated paper
NOTE 1 During the winding process, each paper layer is bonded to the previous layer by its resin coating and the bonding achieved by curing the resin.
NOTE 2 A resin-bonded paper bushing can be provided with an insulating envelope, in which case the intervening space can be filled with an insulating liquid or another insulating medium.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée en papier enduit de résine
RBP (resin-bonded paper)
traversée dont l'isolation principale est assurée par un corps enroulé en papier enduit de résine
NOTE 1 Lors de l'enroulement, chaque couche de papier est liée à la précédente par l'enduit de résine et la cohésion obtenue par le durcissement de la résine.
NOTE 2 Une traversée en papier enduit de résine peut comporter une enveloppe isolante. Dans ce cas, l'espace intermédiaire peut être rempli d'un isolant liquide ou d'un autre milieu isolant.
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > ввод с бумажной изоляцией, склеенной смолой
-
8 изоляционный материал
изоляционный материал
изолятор
-
[IEV number 151-15-35]EN
insulating material
insulant
material used to prevent electric conduction between conductive elements
NOTE – In the field of electromagnetism the term "insulant" is also used as a synonym for "insulating medium".
Source: 212-01-01 MOD, IEC 60050-121
[IEV number 151-15-35]FR
isolant, m
matériau isolant, m
matériau destiné à empêcher la conduction électrique entre des éléments conducteurs
NOTE – En électromagnétisme le terme "isolant" est aussi utilisé comme synonyme de "milieu isolant".
Source: 212-01-01 MOD, CEI 60050-121
[IEV number 151-15-35]Синонимы
EN
DE
FR
- isolant, m
- matériau isolant, m
Русско-немецкий словарь нормативно-технической терминологии > изоляционный материал
-
9 пластмассовая трубная арматура
изоляционная трубная арматура
-
[IEV number 442-02-23]EN
insulating conduit fitting
conduit fitting which consists of insulating material, and which has no conductive components
[IEV number 442-02-23]FR
accessoire isolant de conduit
accessoire de conduit en matériau isolant ne comportant pas de composants conducteurs
[IEV number 442-02-23]Тематики
- электропроводка, электромонтаж
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > пластмассовая трубная арматура
-
10 пластмассовые трубы для электропроводок
пластмассовые трубы для электропроводок
-
изоляционная труба1)
-
[IEV number 442-02-11]EN
insulating conduit
a conduit which consists uniquely of insulating material and which has no conductive components whatever, either in the form of an internal lining, or in the form of external metal braid or coating
[IEV number 442-02-11]FR
conduit isolant
conduit réalisé exclusivement en matériau isolant sans aucun élément conducteur, que ce soit sous forme de revêtement interne ou de tresse ou de revêtement métallique externe
[IEV number 442-02-11]1) В российской документации применяют термин пластмассовая труба
[Интент]
2.5. Следует применять пластмассовые трубы, т.к. они не требуют защиты от коррозии, обладают малым весом, гладкой поверхностью и высокими электроизоляционными свойствами, технологичны при монтаже.
Стальные трубы следует применять в тех случаях, когда механическая и термическая прочность пластмассовых труб недостаточна, а также исходя из условий обеспечения взрыво-пожаробезопасности установок и экономической целесообразности.
3.2. Пластмассовые трубы для электропроводок изготавливают из полиэтилена (ПЭ) высокого давления (ПВД), полиэтилена низкого давления (ПНД), непластифицированного поливинилхлорида (НПВХ) и полипропилена (ПП).
3.3. Трубы изготавливают гладкими и гофрированными. Гофрированные трубы по сравнению с гладкими имеют в два раза меньшую материалоемкость.
Температура начала размягчения для труб из НПВХ – 60 °С, ПВД – 90 °С, ПНД – 100 °С, ПП – 120 °С.
3.4. По результатам испытаний на горючесть трубы из полиэтилена и полипропилена являются горючими, трубы из поливинилхлорида (непластифицированного) - трудногорючими.
3.5. Гладкие трубы из ПЭ с наружным диаметром до 50 мм и из ПП - до 32 мм поставляются в бухтах. При большем наружном диаметре трубы поставляются прямолинейными отрезками длиной 5-10 м в пачках. Гладкие трубы из НПВХ поставляют в пачках прямолинейными отрезками длиной 6-10 м с раструбом на одном конце или без раструба. Гофрированные трубы поставляются в бухтах.
3.6. Пластмассовые трубы обладают различной степенью стойкости к химически активным и др. средам и их выбор следует производить, руководствуясь данными каталога «Химическая стойкость труб из термопластов» (г. Черкассы, НИИТЭХИМ, 1985 г.), а также краткими данными химической стойкости пластмассовых труб, приведенными в справочном прил.1.
4.4. Для соединения и присоединения пластмассовых труб следует применять соединительные муфты и уплотнительные втулки по ТУ 36-1728-81, мерные отрезки шланга из термоусаживающегося материала.
[Министерство архитектуры, строительства и жилищно-коммунального хозяйства. Концерн «ЭЛЕКТРОМОНТАЖ». Инструкция по монтажу электропроводок в трубах]Недопустимые, нерекомендуемые
Тематики
- электропроводка, электромонтаж
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > пластмассовые трубы для электропроводок
-
11 штыревой линейный изолятор
- Stützenisolator, m
- Freileitungsstützisolator
штыревой линейный изолятор
Линейный изолятор, состоящий из изоляционной части с арматурой в виде штыря или крюка.
Примечание. Изоляционная часть может состоять из одной или нескольких соединенных вместе деталей.
[ ГОСТ 27744-88]EN
pin insulator
rigid insulator consisting of an insulating component intended to be mounted rigidly on a supporting structure by means of a pin passing up inside the insulating component which consists of one or more pieces of insulating material permanently connected together
[IEV number 471-03-06]FR
isolateur rigide à tige
isolateur rigide composé d’une partie isolante destinée à être montée de façon rigide sur un support au moyen d’une tige pénétrant à l’intérieur de la partie isolante; il est constitué d’une ou plusieurs pièces isolantes assemblées de façon permanente
[IEV number 471-03-06]17 - Ребро изолятора
21 - Вылет ребра изолятора
23 - Головка изолятора
24 - Паз изолятора
25 - Шейка изолятора
72 - Штырь изолятораШтыревые изоляторы высокого напряжения состоят из двух фарфоровых деталей. Последние жестко соединяются друг с другом с помощью цементо-песчаного состава. Штыревые изоляторы армируются на металлических штырях, закрепляемых на траверсах опор. Все штыревые изоляторы обеспечивают жесткое крепление проводов на опорах.
[ http://sfel.narod.ru/Database/Izolators/Stirevie_lv_hv.htm]
Параллельные тексты EN-RUPin Insulator
The pin insulator gets its name from the fact that it is supported on a pin.
The pin holds the insulator, and the insulator has the conductor tied to it.
Pin insulators are made of either glass or porcelain.
The glass insulator is always one solid piece.
The porcelain insulator is also a one-piece insulator when used with low-voltage lines but will consist of two, three, or four layers cemented together to form a rigid unit when used on higher voltages.
[ http://constructionmanuals.tpub.com/14026/css/14026_100.htm]Штыревой линейный изолятор
Данный изолятор называют штыревым потому что он крепится на штыре.
Штырь удерживает изоляционную часть, к которой прикрепляют провод.
Изоляционную часть изготовляют из стекла или фарфора.
Стеклянная изоляционная часть всегда состоит из одной детали.
Фарфоровая изоляционная часть штыревого изолятора, применяемого в низковольтной линии электропередачи, также состоит из одной детали. В высоковольтных линиях применяют фарфоровые изоляционные части, состоящие из двух, трех или четырех жестко скрепленных деталей.
[Перевод Интент]
Тематики
Классификация
>>>Обобщающие термины
EN
DE
- Freileitungsstützisolator
- Stützenisolator, m
FR
Русско-немецкий словарь нормативно-технической терминологии > штыревой линейный изолятор
-
12 метод пассивации поверхности с помощью высокоомного поликристаллического кремния
nmicroel. SIPOS, Semi-Insulating Polycriystalline Silicon, Semi-Insulating Polycrystalline SiliconУниверсальный русско-немецкий словарь > метод пассивации поверхности с помощью высокоомного поликристаллического кремния
-
13 метод получения поликремниевых структур с гетеропереходом
nmicroel. SIPOS, Semi-Insulating Polycriystalline Silicon, Semi-Insulating Polycrystalline SiliconУниверсальный русско-немецкий словарь > метод получения поликремниевых структур с гетеропереходом
-
14 панель
fFRA plaque f de connexionDEU Anschlußplatte fENG connecting plateITA piastra f di connessionePLN płytka f mocującaRUS панель fсм. поз. 2118 на—FRA panneau m de porteDEU Bekleidungsplatte fENG panelITA pannello m di rivestimentoPLN płyta f drzwiRUS панель f дверисм. поз. 1176 на—FRA plaque f support de condensateurDEU Kondensatorplatte fITA piastra f di supporto dei condensatoriPLN podstawra f kondensatoraRUS панель f конденсаторасм. поз. 2116 на—FRA panneau m de plancher mobileITA pannello m amovibile di pavimentoPLN płyta f podłogi wstawianejRUS панель f пола—FRA plaque f de recouvrementDEU Abdeckung fENG cover plateITA piastra f di coperturaPLN osłona f nastawiaczaRUS панель f привода регуляторасм. поз. 2272 на—FRA panneau m de toitDEU Dachplatte fENG roof panelITA pannello m di tettoPLN płyta f dachu składanegoRUS панель f складывающейся крышисм. поз. 1004 на—FRA panneau m de paroiDEU Bekleidungsplatte fENG panelITA pannello m di paretePLN płyta f ściennaRUS панель f стенысм. поз. 954 напанель, изолирующая
—FRA plaque f isolanteDEU Isolierplatte fENG insulating plateITA piastra f isolantePLN płytka f izolującaRUS панель f, изолирующаясм. поз. 2129 на,
панель, клеммная
—FRA plaque f à bornesDEU Klemmenplatte fENG terminal plateITA morsettiera fPLN płytka f zaciskowaRUS панель f, клеммнаясм. поз. 726 напанель, термоизоляционная
—FRA panneau m isolantDEU Wärmedämmplatte fENG insulating panelITA pannello m isolantePLN płyta f izolującaRUS панель f, термоизоляционнаясм. поз. 1878 на -
15 время защитного действия изолирующего защитного полимерного покрытия
- Schutzwirkungszeit des lokalisierenden Schutzpolymeranstriches
- Schutzwirkungszeit des Isolierschutzpolymeranstriches
время защитного действия изолирующего защитного полимерного покрытия
время защитного действия изолирующего покрытия
Интервал времени, в течение которого изолирующее защитное полимерное покрытие предотвращает радиоактивное загрязнение защищаемой поверхности.
[ ГОСТ 19465-74]Тематики
- покрытия для улучшения радиац. обстан.
Синонимы
EN
DE
FR
8. Время защитного действия изолирующего защитного полимерного покрытия
Время защитного действия изолирующего покрытия
D. Schutzwirkungszeit des Isolierschutzpolymeranstriches
E. Insulating polymeric covering protective power time
F. La durée de protection de la couverture isolante polymère de protection
8a. Время защитного действия локализирующего защитного полимерного покрытия
Время защитного действия локализирующего покрытия
D. Schutzwirkungszeit des lokalisierenden Schutzpolymeranstriches
E. Localizing polymeric covering protective power time
F. La durée de protection de la couverture localisante polymère de protection
Источник: ГОСТ 19465-74: Покрытия полимерные защитные для улучшения радиационной обстановки. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > время защитного действия изолирующего защитного полимерного покрытия
-
16 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
17 изолирующее защитное полимерное покрытие
изолирующее защитное полимерное покрытие
изолирующее покрытие
Защитное полимерное покрытие для улучшения радиационной обстановки, обладающее способностью в течение времени эксплуатации предотвращать радиоактивное загрязнение защищаемой поверхности.
[ ГОСТ 19465-74]Тематики
- покрытия для улучшения радиац. обстан.
Синонимы
EN
DE
FR
5. Изолирующее защитное полимерное покрытие
Изолирующее покрытие
D. Isodierpolymeranstrich
E. Insulating polymeric covering
F. Une couverture isolante polymère
Защитное полимерное покрытие для улучшения радиационной обстановки, обладающее способностью в течение времени эксплуатации предотвращать радиоактивное загрязнение защищаемой поверхности
Источник: ГОСТ 19465-74: Покрытия полимерные защитные для улучшения радиационной обстановки. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > изолирующее защитное полимерное покрытие
-
18 кровля обратная
кровля обратная
Кровля плоской крыши с теплоизолирующим слоем поверх гидроизоляционного слоя
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
- inverted roof (roof with heat insulating layer over waterproof protection cover)
- inverted roofing (roof with heat insulating layer over waterproof protection cover)
DE
FR
- toiture retournée (toiture avec la couche ďisolation thermique au - dessus de la couverture hydrofuge)
Русско-немецкий словарь нормативно-технической терминологии > кровля обратная
-
19 штыревой опорный изолятор
- Stielflansch-Stützisolator, m
- Gerätestützisolator
штыревой опорный изолятор
Опорный изолятор, состоящий из одной или нескольких изоляционных частей с ребрами, постоянно соединенными между собой и арматурой в виде колпака и штыря.
[ ГОСТ 27744-88]EN
pedestal post insulator
post insulator having two metal parts, a cap partly embracing an insulating component and a “pedestal” cemented into a recess in the insulating component; the cap normally has tapped holes and the pedestal a flange with plain holes for attachment by bolts or screws
[IEV number 471-04-05]FR
support isolant à capot et embase
support isolant ayant deux parties métalliques, un capot recouvrant partiellement une pièce isolante et une embase scellée à l’intérieur d’un logement prévu dans la pièce isolante; normalement le capot comporte des trous taraudés et l’embase une bride avec des trous lisses pour permettre une fixation par vis ou boulons
[IEV number 471-04-05]
16 - Тело изолятора
17 - Ребро изолятора
21 - Вылет ребра изолятора
71 - Колпак изолятора
72 - Штырь изолятораТематики
Классификация
>>>EN
DE
- Gerätestützisolator
- Stielflansch-Stützisolator, m
FR
Русско-немецкий словарь нормативно-технической терминологии > штыревой опорный изолятор
-
20 электрическая прочность изоляции ФЭПП
электрическая прочность изоляции ФЭПП
Максимально допустимое напряжение между выводами и корпусом ФЭПП, при котором в течение длительного времени не происходит пробоя изоляции или уменьшения сопротивления изоляции.
Обозначение
Uиз
Ui
[ ГОСТ 21934-83]Тематики
- приемники излуч. полупроводн. и фотоприемн. устр.
EN
DE
FR
52. Электрическая прочность изоляции ФЭПП
D. Isolationsfestigkeit
E. Insulating strength
F. Rigidité d'isolement
uиз
Максимально допустимое напряжение между выводами и корпусом ФЭПП, при котором в течение длительного времени не происходит пробоя изоляции или уменьшения сопротивления изоляции
Источник: ГОСТ 21934-83: Приемники излучения полупроводниковые фотоэлектрические и фотоприемные устройства. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > электрическая прочность изоляции ФЭПП
См. также в других словарях:
Insulating — Insulate In su*late, v. t. [imp. & p. p. {Insulated}; p. pr. & vb. n. {Insulating}.] [L. insulatus insulated, fr. insula island. See {Isle}, and cf. {Isolate}.] [1913 Webster] 1. To make an island of. [Obs.] Pennant. [1913 Webster] 2. To place in … The Collaborative International Dictionary of English
insulating — adjective : serving to insulate : functioning as insulation insulating material an insulating calm … Useful english dictionary
insulating — adj. Insulating is used with these nouns: ↑tape … Collocations dictionary
Insulating concrete forms — ( ICFs ) are stay in place formwork for energy efficient, cast in place reinforced concrete walls.The forms are interlocking modular units that are dry stacked (without mortar) and filled with concrete. The forms lock together somewhat like Lego… … Wikipedia
insulating tape — insulating .tape n [U] a type of sticky tape used for wrapping around electric wires to insulate them … Dictionary of contemporary English
insulating tape — ► NOUN ▪ adhesive tape used to cover exposed electric wires … English terms dictionary
Insulating stool — Insulate In su*late, v. t. [imp. & p. p. {Insulated}; p. pr. & vb. n. {Insulating}.] [L. insulatus insulated, fr. insula island. See {Isle}, and cf. {Isolate}.] [1913 Webster] 1. To make an island of. [Obs.] Pennant. [1913 Webster] 2. To place in … The Collaborative International Dictionary of English
insulating tape — noun a water resistant adhesive tape used to insulate exposed electrical conductors • Syn: ↑friction tape • Hypernyms: ↑adhesive tape * * * ˈinsulating tape [insulating tape insulating tapes] ( … Useful english dictionary
insulating board — noun or insulation board : a board with insulating properties; especially : a structural or finish material that consists of sheets of lightly compressed vegetable pulp variously finished and is used especially for its thermal insulating effect… … Useful english dictionary
insulating base — izoliacinis padėklas statusas T sritis radioelektronika atitikmenys: angl. insulating base; insulating substrate vok. isolierende Unterlage, f; isolierendes Substant, m rus. изолирующая подложка, f pranc. substrat isolant, m … Radioelektronikos terminų žodynas
insulating substrate — izoliacinis padėklas statusas T sritis radioelektronika atitikmenys: angl. insulating base; insulating substrate vok. isolierende Unterlage, f; isolierendes Substant, m rus. изолирующая подложка, f pranc. substrat isolant, m … Radioelektronikos terminų žodynas