-
1 расстояние утечки
расстояние утечки
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание. Стык между двумя элементами из изоляционного материала считают частью поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
расстояние утечки (см. приложение В)
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание — При определении расстояния утечки относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9
[ ГОСТ Р 50345-99( МЭК 60898-95)]
расстояние утечки по поверхности
-
[IEV number 151-15-50]
путь утечки
Кратчайшее расстояние вдоль поверхности изоляции между двумя проводящими частями или между проводящей частью и доступной поверхностью.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - A joint between two pieces of insulating material is considered part of the surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - For the purpose of determining a creepage distance to accessible parts, the accessible surface of an insulating enclosure is considered conductive as if it was covered by a metal foil wherever it can be touched by a hand or a standard test finger according to figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
creepage distance
shortest distance along the surface of insulation between two conductive parts or between a conductive part and the accessible surface
[IEC 60335-1, ed. 4.0 (2001-05)]
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts
[IEV number 151-15-50]FR
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Un joint entre deux portions de matière isolante est considéré comme faisant partie de la surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Pour la détermination d'une ligne de fuite pour des parties accessibles, la surface accessible d'une enveloppe isolante est considérée comme conductrice comme si elle était recouverte d'une feuille métallique à tout endroit où elle peut être touchée par la main ou par le doigt d'essai normalisé conforme à la figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
ligne de fuite
plus petite distance le long de la surface de l’isolation entre deux parties conductrices ou entre une partie conductrice et la surface accessible
[IEC 60335-1, ed. 4.0 (2001-05)]
ligne de fuite, f
distance la plus courte, le long de la surface d'un isolant solide, entre deux parties conductrices
[IEV number 151-15-50]1) Должно быть проводящими
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > расстояние утечки
-
2 ввод с бумажно-масляной изоляцией
- traversée en papier imprégné d’huile
- OIP
ввод с бумажно-масляной изоляцией
Ввод, в котором основная изоляция состоит из бумаги, пропитанной изоляционной жидкостью.
Примечание. Бумага, в основном, пропитывается трансформаторным маслом.
[ ГОСТ 27744-88]EN
oil-impregnated paper bushing
OIP
bushing in which the major insulation consists of a core wound from paper and subsequently treated and impregnated with an insulating liquid, generally transformer oil
NOTE The core is contained in an insulating envelope, the space between the core and the insulating envelope being filled with the same insulating liquid as that used for impregnation.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée en papier imprégnée d'huile
OIP (oil-impregnated paper)
traversée dont l'isolation principale est assurée par un corps enroulé en papier ultérieurement traité et imprégné d'un liquide isolant, généralement d'huile de transformateur
NOTE Le corps est placé dans une enveloppe isolante, l'espace entre le corps et l'enveloppe isolante étant rempli du même liquide isolant que celui employé pour l'imprégnation
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
DE
FR
- OIP
- traversée en papier imprégné d’huile
Русско-французский словарь нормативно-технической терминологии > ввод с бумажно-масляной изоляцией
-
3 проходной изолятор
- traversée
- isolateur de traversée, m
проходной изолятор
Изолятор, предназначенный для провода токоведущих элементов через стенку, имеющую другой электрический потенциал.
[ ГОСТ 27744-88]
проходной изолятор
-
[IEV number 151-15-40]EN
(insulating) bushing
insulator forming a passage for a conductor through a non-insulating partition
[IEV number 151-15-40]
bushing
A bushing is a cyclindrical insulating component, usually made of ceramic, that houses a conductor. It enables a conductor to pass through a grounded enclosure, such as a transformer tank (the physical shell of a transformer), a wall or other physical barrier, to connect electrical installations. In the case of a transformer, bushings protect the conductors that connect a transformer’s core to the power system it serves through channels in the transformer’s housing.
[ABB. Glossary of technical terms. 2010]FR
isolateur de traversée, m
traversée, f
isolateur permettant le passage d'un conducteur à travers une paroi non isolante
[IEV number 151-15-40]
Проходной изоляторПараллельные тексты EN-RU
The circuit breaker is connected via bushings to the rest of the switchgear at the flanges provided.
[Siemens]С другими частями распределительного устройства силовой выключатель соединяется через проходные изоляторы, закрепленные в его фланцах.
[Перевод Интент]Тематики
Классификация
>>>Обобщающие термины
EN
DE
FR
- isolateur de traversée, m
- traversée
Русско-французский словарь нормативно-технической терминологии > проходной изолятор
-
4 ввод с бумажной изоляцией, пропитанной смолой
ввод с бумажной изоляцией, пропитанной смолой
Ввод, в котором основная изоляция состоит из бумаги, пропитанной смолой.
[ ГОСТ 27744-88]EN
resin-impregnated paper bushing
RIP
bushing in which the major insulation consists of a core wound from untreated paper and subsequently impregnated with a curable resin
NOTE A resin-impregnated paper bushing can be provided with an insulating envelope, in which case the intervening space can be filled with an insulating liquid or another insulating medium.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée en papier imprégné de résine
RIP (resin-impregnated paper)
traversée dont l'isolation principale est assurée par un corps enroulé en papier non traité et ensuite imprégné de résine durcissable
NOTE Une traversée en papier imprégné de résine peut comporter une enveloppe isolante. Dans ce cas, l'espace intermédiaire peut être rempli d'un isolant liquide ou d'un autre milieu isolant
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ввод с бумажной изоляцией, пропитанной смолой
-
5 ввод с бумажной изоляцией, склеенной смолой
ввод с бумажной изоляцией, склеенной смолой
Ввод, в котором основная изоляция состоит из бумаги, склеенной смолой.
[ ГОСТ 27744-88]EN
resin-bonded paper bushing
RBP
bushing in which the major insulation consists of a core wound from resin-coated paper
NOTE 1 During the winding process, each paper layer is bonded to the previous layer by its resin coating and the bonding achieved by curing the resin.
NOTE 2 A resin-bonded paper bushing can be provided with an insulating envelope, in which case the intervening space can be filled with an insulating liquid or another insulating medium.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée en papier enduit de résine
RBP (resin-bonded paper)
traversée dont l'isolation principale est assurée par un corps enroulé en papier enduit de résine
NOTE 1 Lors de l'enroulement, chaque couche de papier est liée à la précédente par l'enduit de résine et la cohésion obtenue par le durcissement de la résine.
NOTE 2 Une traversée en papier enduit de résine peut comporter une enveloppe isolante. Dans ce cas, l'espace intermédiaire peut être rempli d'un isolant liquide ou d'un autre milieu isolant.
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ввод с бумажной изоляцией, склеенной смолой
-
6 ввод с газовой изоляцией
ввод с газовой изоляцией
Ввод, в котором основной изоляцией является газ (отличающийся от окружающего воздуха) под давлением, большим атмосферного или равным ему.
[ ГОСТ 27744-88]EN
gas-insulated bushing
bushing in which the major insulation consists of gas (other than ambient air) at atmospheric pressure or higher
NOTE 1 This definition includes bushings which are intended to form an integral part of gas-insulated equipment, the gas of the equipment being in communication with that of the bushing.
NOTE 2 A bushing which contains solid insulating materials other than the envelope containing the gas (e.g. support for conducting layers or insulating cylinder), is a combined insulation bushing (see 3.13).
NOTE 3 A bushing in which the desired voltage grading is obtained by an arrangement of conducting or semi-conducting layers incorporated in an insulating material (e.g. plastic film) is referred to as a gas insulated condenser graded bushing.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée à isolation gazeuse
traversée dont l'isolation principale est assurée par un gaz (autre que l'air ambiant) à une pression supérieure ou égale à la pression atmosphérique
NOTE 1 Cette définition comprend les traversées destinées à faire partie intégrante d'une installation à isolation gazeuse où le gaz de l'installation est en communication avec celui de la traversée.
NOTE 2 Une traversée qui comporte des matériaux isolants solides autres que l'enveloppe contenant le gaz (par exemple un support pour des couches conductrices ou un cylindre isolant) est une traversée à isolation composite (voir 3.13).
NOTE 3 Une traversée dans laquelle la répartition de tension souhaitée est obtenue par la disposition de couches conductrices ou semi-conductrices incorporées au matériau isolant (par exemple film plastique) est désignée par une traversée à isolation gazeuse à répartition capacitive.
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > ввод с газовой изоляцией
-
7 изоляционный материал
- matériau isolant, m
- isolant, m
изоляционный материал
изолятор
-
[IEV number 151-15-35]EN
insulating material
insulant
material used to prevent electric conduction between conductive elements
NOTE – In the field of electromagnetism the term "insulant" is also used as a synonym for "insulating medium".
Source: 212-01-01 MOD, IEC 60050-121
[IEV number 151-15-35]FR
isolant, m
matériau isolant, m
matériau destiné à empêcher la conduction électrique entre des éléments conducteurs
NOTE – En électromagnétisme le terme "isolant" est aussi utilisé comme synonyme de "milieu isolant".
Source: 212-01-01 MOD, CEI 60050-121
[IEV number 151-15-35]Синонимы
EN
DE
FR
- isolant, m
- matériau isolant, m
Русско-французский словарь нормативно-технической терминологии > изоляционный материал
-
8 комплектное распределительное устройство в металлической оболочке
- pareillage d’armoire
- appareillage sous enveloppe métallique
- appareillage recouvert de métal
- appareillage à compartiments (avec cloisons non métalliques)
комплектное распределительное устройство в металлической оболочке
-EN
metal-enclosed switchgear
switchgear assemblies with an external metallic enclosure intended to be earthed and complete except for external connections
NOTE The metal-enclosed switchgear is subdivided into three types:
– metal-clad switchgear;
– compartmented switchgear (with one or more non-metallic partitions);
– cubicle switchgear
[IEC 61992-1, ed. 2.0 (2006-02)]
metal-clad switchgear
metal-enclosed switchgear in which components are arranged in separate compartments with metal partitions intended to be earthed
NOTE 1 This term applies to metal-enclosed switchgear with metal partitions providing the degree of protection (or higher) included in IEC 61992-6 and having separate compartments at least for the following components:
– each main switching device;
– components connected to one side of a main switching device, for example, feeder circuit;
– components connected to the other side of the main switching device, for example, busbars; where more than one set of busbars is provided, each set is in a separate compartment.
NOTE 2 Metal-enclosed switchgear having metal partitions and meeting all the requirements of NOTE 1 may utilise an insulating shutter barrier as a part of a shutter arrangement, the combination of which provides the degree of protection included in Table 1 of IEC 61992-6 (or higher) and satisfies the requirements of the standard for partitions and shutters made of insulating material.
[IEC 61992-1, ed. 2.0 (2006-02)]
compartmented switchgear (with non-metallic partitions)
metal-enclosed switchgear in which components are arranged in separate compartments as for metal-clad switchgear, but with one or more non-metallic partitions providing the degree of protection (or higher) included in Table 1 of IEC 61992-6
NOTE Metal-enclosed switchgear in which the main circuit components are individually embedded in solid insulating material can be considered as an alternative, provided that the conditions specified in IEC 60466 are met.
[IEC 61992-1, ed. 2.0 (2006-02)]
cubicle switchgear
switchgear, other than metal-clad and compartmented switchgear
NOTE This term applies to switchgear having a metal enclosure and having
– a number of compartments fewer than required for metal-clad or compartmented switchgear, or
– partitions having a degree of protection lower than those indicated in Table 1 of IEC 61992-6, or
– no partitions.
[IEC 61992-1, ed. 2.0 (2006-02)]FR
appareillage sous enveloppe métallique
ensemble d’appareillage avec une enveloppe métallique externe destinée à être mise à la terre, entièrement terminé, à l’exception des connexions extérieures
NOTE L’appareillage sous enveloppe métallique se subdivise en trois types:
– appareillage recouvert de métal;
– appareillage à compartiments (avec une ou plusieurs cloisons non métalliques);
– appareillage d’armoire.
[IEC 61992-1, ed. 2.0 (2006-02)]
appareillage recouvert de métal
appareillage sous enveloppe métallique dans lequel les éléments constitutifs sont disposés dans des compartiments séparés par des cloisons métalliques destinées à être mises à la terre
NOTE 1 Ce terme s’applique à l’appareillage sous enveloppe métallique avec des cloisons métalliques offrant le degré de protection de la CEI 61992-6 (ou un degré supérieur) et ayant des compartiments séparés au moins pour les éléments constitutifs suivants:
– chaque appareil principal de connexion;
– les éléments constitutifs connectés à une face de l'appareil principal de connexion, par exemple le circuit d’alimentation;
– les éléments constitutifs connectés à l’autre face de l'appareil principal de connexion, par exemple les jeux de barres; lorsqu’il y a plus d’un jeu de barres, chaque jeu est dans un compartiment séparé.
NOTE 2 L’appareillage sous enveloppe métallique qui possède des cloisons métalliques et qui répond à toutes les dispositions de la note 1 peut utiliser une barrière en volet isolant comme une partie d’une disposition de volet, dont la combinaison fournit un degré de protection inclus au Tableau 1 de la CEI 61992-6 (ou un degré supérieur) et satisfait aux exigences de la norme pour les cloisons et les volets en matériau isolant.
[IEC 61992-1, ed. 2.0 (2006-02)]
appareillage à compartiments (avec cloisons non métalliques)
appareillage sous enveloppe métallique dans lequel les éléments constitutifs sont disposés dans des compartiments séparés comme pour l’appareillage recouvert de métal, mais avec une ou plusieurs cloisons non métalliques fournissant le degré de protection du Tableau 1 de la CEI 61992-6 (ou un degré supérieur)
NOTE L’appareillage sous enveloppe métallique dans lequel les éléments constitutifs du circuit principal sont noyés individuellement dans un matériau isolant solide peut être considéré comme une alternative, si les conditions spécifiées dans la CEI 60466 sont satisfaites.
[IEC 61992-1, ed. 2.0 (2006-02)]
pareillage d’armoire
appareillage, autre que l’appareillage recouvert de métal ou à compartiments
NOTE Ce terme s’applique à l’appareillage ayant une enveloppe métallique et ayant:
– soit un nombre de compartiments inférieur à celui exigé pour les appareillages recouverts de métal ou à compartiments;
– soit des cloisons d’un degré de protection inférieur à ceux du Tableau 1 de la CEI 61992-6;
– soit pas de cloisons.
[IEC 61992-1, ed. 2.0 (2006-02)]
Комплектное распределительное устройство в металлической оболочке
Рис. ABBГОСТ 14693-90 - Устройства комплектные распределительные негерметизированные в металлической оболочке на напряжение до 10 кВ
Тематики
- комплектное распред. устройство (КРУ)
Синонимы
EN
- compartmented switchgear (with non-metallic partitions)
- cubicle switchgear
- MCSG
- MESG
- metal clad switch gear
- metal clad switchgear
- metal-enclosed switchgear
- metalclad switch gear
- metalclad switchgear
FR
Русско-французский словарь нормативно-технической терминологии > комплектное распределительное устройство в металлической оболочке
-
9 пластмассовая трубная арматура
изоляционная трубная арматура
-
[IEV number 442-02-23]EN
insulating conduit fitting
conduit fitting which consists of insulating material, and which has no conductive components
[IEV number 442-02-23]FR
accessoire isolant de conduit
accessoire de conduit en matériau isolant ne comportant pas de composants conducteurs
[IEV number 442-02-23]Тематики
- электропроводка, электромонтаж
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > пластмассовая трубная арматура
-
10 пластмассовые трубы для электропроводок
пластмассовые трубы для электропроводок
-
изоляционная труба1)
-
[IEV number 442-02-11]EN
insulating conduit
a conduit which consists uniquely of insulating material and which has no conductive components whatever, either in the form of an internal lining, or in the form of external metal braid or coating
[IEV number 442-02-11]FR
conduit isolant
conduit réalisé exclusivement en matériau isolant sans aucun élément conducteur, que ce soit sous forme de revêtement interne ou de tresse ou de revêtement métallique externe
[IEV number 442-02-11]1) В российской документации применяют термин пластмассовая труба
[Интент]
2.5. Следует применять пластмассовые трубы, т.к. они не требуют защиты от коррозии, обладают малым весом, гладкой поверхностью и высокими электроизоляционными свойствами, технологичны при монтаже.
Стальные трубы следует применять в тех случаях, когда механическая и термическая прочность пластмассовых труб недостаточна, а также исходя из условий обеспечения взрыво-пожаробезопасности установок и экономической целесообразности.
3.2. Пластмассовые трубы для электропроводок изготавливают из полиэтилена (ПЭ) высокого давления (ПВД), полиэтилена низкого давления (ПНД), непластифицированного поливинилхлорида (НПВХ) и полипропилена (ПП).
3.3. Трубы изготавливают гладкими и гофрированными. Гофрированные трубы по сравнению с гладкими имеют в два раза меньшую материалоемкость.
Температура начала размягчения для труб из НПВХ – 60 °С, ПВД – 90 °С, ПНД – 100 °С, ПП – 120 °С.
3.4. По результатам испытаний на горючесть трубы из полиэтилена и полипропилена являются горючими, трубы из поливинилхлорида (непластифицированного) - трудногорючими.
3.5. Гладкие трубы из ПЭ с наружным диаметром до 50 мм и из ПП - до 32 мм поставляются в бухтах. При большем наружном диаметре трубы поставляются прямолинейными отрезками длиной 5-10 м в пачках. Гладкие трубы из НПВХ поставляют в пачках прямолинейными отрезками длиной 6-10 м с раструбом на одном конце или без раструба. Гофрированные трубы поставляются в бухтах.
3.6. Пластмассовые трубы обладают различной степенью стойкости к химически активным и др. средам и их выбор следует производить, руководствуясь данными каталога «Химическая стойкость труб из термопластов» (г. Черкассы, НИИТЭХИМ, 1985 г.), а также краткими данными химической стойкости пластмассовых труб, приведенными в справочном прил.1.
4.4. Для соединения и присоединения пластмассовых труб следует применять соединительные муфты и уплотнительные втулки по ТУ 36-1728-81, мерные отрезки шланга из термоусаживающегося материала.
[Министерство архитектуры, строительства и жилищно-коммунального хозяйства. Концерн «ЭЛЕКТРОМОНТАЖ». Инструкция по монтажу электропроводок в трубах]Недопустимые, нерекомендуемые
Тематики
- электропроводка, электромонтаж
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > пластмассовые трубы для электропроводок
-
11 штыревой линейный изолятор
штыревой линейный изолятор
Линейный изолятор, состоящий из изоляционной части с арматурой в виде штыря или крюка.
Примечание. Изоляционная часть может состоять из одной или нескольких соединенных вместе деталей.
[ ГОСТ 27744-88]EN
pin insulator
rigid insulator consisting of an insulating component intended to be mounted rigidly on a supporting structure by means of a pin passing up inside the insulating component which consists of one or more pieces of insulating material permanently connected together
[IEV number 471-03-06]FR
isolateur rigide à tige
isolateur rigide composé d’une partie isolante destinée à être montée de façon rigide sur un support au moyen d’une tige pénétrant à l’intérieur de la partie isolante; il est constitué d’une ou plusieurs pièces isolantes assemblées de façon permanente
[IEV number 471-03-06]17 - Ребро изолятора
21 - Вылет ребра изолятора
23 - Головка изолятора
24 - Паз изолятора
25 - Шейка изолятора
72 - Штырь изолятораШтыревые изоляторы высокого напряжения состоят из двух фарфоровых деталей. Последние жестко соединяются друг с другом с помощью цементо-песчаного состава. Штыревые изоляторы армируются на металлических штырях, закрепляемых на траверсах опор. Все штыревые изоляторы обеспечивают жесткое крепление проводов на опорах.
[ http://sfel.narod.ru/Database/Izolators/Stirevie_lv_hv.htm]
Параллельные тексты EN-RUPin Insulator
The pin insulator gets its name from the fact that it is supported on a pin.
The pin holds the insulator, and the insulator has the conductor tied to it.
Pin insulators are made of either glass or porcelain.
The glass insulator is always one solid piece.
The porcelain insulator is also a one-piece insulator when used with low-voltage lines but will consist of two, three, or four layers cemented together to form a rigid unit when used on higher voltages.
[ http://constructionmanuals.tpub.com/14026/css/14026_100.htm]Штыревой линейный изолятор
Данный изолятор называют штыревым потому что он крепится на штыре.
Штырь удерживает изоляционную часть, к которой прикрепляют провод.
Изоляционную часть изготовляют из стекла или фарфора.
Стеклянная изоляционная часть всегда состоит из одной детали.
Фарфоровая изоляционная часть штыревого изолятора, применяемого в низковольтной линии электропередачи, также состоит из одной детали. В высоковольтных линиях применяют фарфоровые изоляционные части, состоящие из двух, трех или четырех жестко скрепленных деталей.
[Перевод Интент]
Тематики
Классификация
>>>Обобщающие термины
EN
DE
- Freileitungsstützisolator
- Stützenisolator, m
FR
Русско-французский словарь нормативно-технической терминологии > штыревой линейный изолятор
-
12 время защитного действия изолирующего защитного полимерного покрытия
- La durée de protection de la couverture localisante polymère de protection
- la durée de protection de la couverture isolante polymère de protection
время защитного действия изолирующего защитного полимерного покрытия
время защитного действия изолирующего покрытия
Интервал времени, в течение которого изолирующее защитное полимерное покрытие предотвращает радиоактивное загрязнение защищаемой поверхности.
[ ГОСТ 19465-74]Тематики
- покрытия для улучшения радиац. обстан.
Синонимы
EN
DE
FR
8. Время защитного действия изолирующего защитного полимерного покрытия
Время защитного действия изолирующего покрытия
D. Schutzwirkungszeit des Isolierschutzpolymeranstriches
E. Insulating polymeric covering protective power time
F. La durée de protection de la couverture isolante polymère de protection
8a. Время защитного действия локализирующего защитного полимерного покрытия
Время защитного действия локализирующего покрытия
D. Schutzwirkungszeit des lokalisierenden Schutzpolymeranstriches
E. Localizing polymeric covering protective power time
F. La durée de protection de la couverture localisante polymère de protection
Источник: ГОСТ 19465-74: Покрытия полимерные защитные для улучшения радиационной обстановки. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > время защитного действия изолирующего защитного полимерного покрытия
-
13 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
14 изолирующее защитное полимерное покрытие
изолирующее защитное полимерное покрытие
изолирующее покрытие
Защитное полимерное покрытие для улучшения радиационной обстановки, обладающее способностью в течение времени эксплуатации предотвращать радиоактивное загрязнение защищаемой поверхности.
[ ГОСТ 19465-74]Тематики
- покрытия для улучшения радиац. обстан.
Синонимы
EN
DE
FR
5. Изолирующее защитное полимерное покрытие
Изолирующее покрытие
D. Isodierpolymeranstrich
E. Insulating polymeric covering
F. Une couverture isolante polymère
Защитное полимерное покрытие для улучшения радиационной обстановки, обладающее способностью в течение времени эксплуатации предотвращать радиоактивное загрязнение защищаемой поверхности
Источник: ГОСТ 19465-74: Покрытия полимерные защитные для улучшения радиационной обстановки. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > изолирующее защитное полимерное покрытие
-
15 кровля обратная
- toiture retournée (toiture avec la couche ďisolation thermique au - dessus de la couverture hydrofuge)
кровля обратная
Кровля плоской крыши с теплоизолирующим слоем поверх гидроизоляционного слоя
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
- inverted roof (roof with heat insulating layer over waterproof protection cover)
- inverted roofing (roof with heat insulating layer over waterproof protection cover)
DE
FR
- toiture retournée (toiture avec la couche ďisolation thermique au - dessus de la couverture hydrofuge)
Русско-французский словарь нормативно-технической терминологии > кровля обратная
-
16 прибор класса 0
прибор класса 0
Прибор, в котором защита от поражения электрическим током обеспечивается только основной изоляцией; это означает, что отсутствуют средства для присоединения проводящих доступных частей, если такие имеются, к защитному проводу в стационарной проводке установки. В случае повреждения основной изоляции защита от поражения электрическим током возлагается на окружающую среду.
Примечание. Приборы класса 0 имеют кожух из изоляционного материала, который может составлять часть или всю основную изоляцию, либо металлический кожух, который отделен от токоведущих частей соответствующей изоляцией. Если прибор с кожухом из изоляционного материала имеет заземляющее устройство для внутренних частей, он считается прибором класса I или класса 01.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
class 0 appliance
appliance in which protection against electric shock relies upon basic insulation only, there being no means for the connection of conductive accessible parts, if any, to the protective conductor in the fixed wiring of the installation, reliance in the event of a failure of the basic insulation being placed upon the environment
NOTE - Class 0 appliances have either an enclosure of insulating material which may form a part or the whole of the basic insulation, or a metal enclosure which is separated from live parts by an appropriate insulation. If an appliance with an enclosure of insulating material has provision for earthing internal parts, it is considered to be a class I appliance or class 0I appliance.
[IEC 60335-1, ed. 4.0 (2001-05)]FR
appareil de la classe 0
appareil dans lequel la protection contre les chocs électriques repose uniquement sur l'isolation principale, ceci impliquant qu'aucune disposition n'existe pour la connexion des parties conductrices accessibles éventuelles à un conducteur de protection des canalisations fixes de l'installation, la protection en cas de défaut de l'isolation principale reposant sur l'environnement
NOTE - Les appareils de la classe 0 ont soit une enveloppe en matière isolante qui peut former tout ou partie de l'isolation principale soit une enveloppe métallique qui est séparée des parties actives par une isolation appropriée. Si un appareil pourvu d'une enveloppe en matière isolante comporte des dispositions en vue de la mise à la terre des parties internes, il est considéré comme étant un appareil de la classe I ou un appareil de la classe 0I.
[IEC 60335-1, ed. 4.0 (2001-05)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > прибор класса 0
-
17 штыревой опорный изолятор
штыревой опорный изолятор
Опорный изолятор, состоящий из одной или нескольких изоляционных частей с ребрами, постоянно соединенными между собой и арматурой в виде колпака и штыря.
[ ГОСТ 27744-88]EN
pedestal post insulator
post insulator having two metal parts, a cap partly embracing an insulating component and a “pedestal” cemented into a recess in the insulating component; the cap normally has tapped holes and the pedestal a flange with plain holes for attachment by bolts or screws
[IEV number 471-04-05]FR
support isolant à capot et embase
support isolant ayant deux parties métalliques, un capot recouvrant partiellement une pièce isolante et une embase scellée à l’intérieur d’un logement prévu dans la pièce isolante; normalement le capot comporte des trous taraudés et l’embase une bride avec des trous lisses pour permettre une fixation par vis ou boulons
[IEV number 471-04-05]
16 - Тело изолятора
17 - Ребро изолятора
21 - Вылет ребра изолятора
71 - Колпак изолятора
72 - Штырь изолятораТематики
Классификация
>>>EN
DE
- Gerätestützisolator
- Stielflansch-Stützisolator, m
FR
Русско-французский словарь нормативно-технической терминологии > штыревой опорный изолятор
-
18 электрическая прочность изоляции ФЭПП
электрическая прочность изоляции ФЭПП
Максимально допустимое напряжение между выводами и корпусом ФЭПП, при котором в течение длительного времени не происходит пробоя изоляции или уменьшения сопротивления изоляции.
Обозначение
Uиз
Ui
[ ГОСТ 21934-83]Тематики
- приемники излуч. полупроводн. и фотоприемн. устр.
EN
DE
FR
52. Электрическая прочность изоляции ФЭПП
D. Isolationsfestigkeit
E. Insulating strength
F. Rigidité d'isolement
uиз
Максимально допустимое напряжение между выводами и корпусом ФЭПП, при котором в течение длительного времени не происходит пробоя изоляции или уменьшения сопротивления изоляции
Источник: ГОСТ 21934-83: Приемники излучения полупроводниковые фотоэлектрические и фотоприемные устройства. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > электрическая прочность изоляции ФЭПП
-
19 автоматический выключатель в пластмассовом корпусе
автоматический выключатель в пластмассовом корпусе
Выключатель, снабженный корпусом из литого изоляционного материала, составляющим неотъемлемую часть автоматического выключателя.
(МЭС 441-14-24)
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]EN
moulded-case circuit-breaker
a circuit-breaker having a supporting housing of moulded insulating material forming an integral part of the circuit-breaker.
[< size="2">IEC 60947-2, ed. 4.0 (2006-05)}FR
disjoncteur en boîtier moulé
disjoncteur dont le châssis et l’enveloppe sont en matériau isolant moulé et font partie intégrante du disjoncteur.
[< size="2">IEC 60947-2, ed. 4.0 (2006-05)}Трехполюсные автоматические выключатели в пластмассовом корпусе
Тематики
Классификация
>>>Обобщающие термины
Синонимы
EN
- MCCB
- moulded case circuit breaker
- moulded case circuit-breaker
- moulded-case circuit breaker
- moulded-case circuit-breaker
DE
FR
Русско-французский словарь нормативно-технической терминологии > автоматический выключатель в пластмассовом корпусе
-
20 асбестовая электроизоляционная бумага
асбестовая электроизоляционная бумага
Электроизоляционная бумага с нормированным показателем потерь при прокаливании, применяемая в качестве теплостойкого диэлектрика в электрических машинах и аппаратах.
[ ГОСТ 17586-80]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > асбестовая электроизоляционная бумага
См. также в других словарях:
Insulating — Insulate In su*late, v. t. [imp. & p. p. {Insulated}; p. pr. & vb. n. {Insulating}.] [L. insulatus insulated, fr. insula island. See {Isle}, and cf. {Isolate}.] [1913 Webster] 1. To make an island of. [Obs.] Pennant. [1913 Webster] 2. To place in … The Collaborative International Dictionary of English
insulating — adjective : serving to insulate : functioning as insulation insulating material an insulating calm … Useful english dictionary
insulating — adj. Insulating is used with these nouns: ↑tape … Collocations dictionary
Insulating concrete forms — ( ICFs ) are stay in place formwork for energy efficient, cast in place reinforced concrete walls.The forms are interlocking modular units that are dry stacked (without mortar) and filled with concrete. The forms lock together somewhat like Lego… … Wikipedia
insulating tape — insulating .tape n [U] a type of sticky tape used for wrapping around electric wires to insulate them … Dictionary of contemporary English
insulating tape — ► NOUN ▪ adhesive tape used to cover exposed electric wires … English terms dictionary
Insulating stool — Insulate In su*late, v. t. [imp. & p. p. {Insulated}; p. pr. & vb. n. {Insulating}.] [L. insulatus insulated, fr. insula island. See {Isle}, and cf. {Isolate}.] [1913 Webster] 1. To make an island of. [Obs.] Pennant. [1913 Webster] 2. To place in … The Collaborative International Dictionary of English
insulating tape — noun a water resistant adhesive tape used to insulate exposed electrical conductors • Syn: ↑friction tape • Hypernyms: ↑adhesive tape * * * ˈinsulating tape [insulating tape insulating tapes] ( … Useful english dictionary
insulating board — noun or insulation board : a board with insulating properties; especially : a structural or finish material that consists of sheets of lightly compressed vegetable pulp variously finished and is used especially for its thermal insulating effect… … Useful english dictionary
insulating base — izoliacinis padėklas statusas T sritis radioelektronika atitikmenys: angl. insulating base; insulating substrate vok. isolierende Unterlage, f; isolierendes Substant, m rus. изолирующая подложка, f pranc. substrat isolant, m … Radioelektronikos terminų žodynas
insulating substrate — izoliacinis padėklas statusas T sritis radioelektronika atitikmenys: angl. insulating base; insulating substrate vok. isolierende Unterlage, f; isolierendes Substant, m rus. изолирующая подложка, f pranc. substrat isolant, m … Radioelektronikos terminų žodynas