-
1 минимальный расцепитель напряжения
минимальный расцепитель напряжения
Расцепитель, автоматически срабатывающий, когда подаваемое напряжение опускается ниже заданного уровня.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]
минимальное реле или минимальной расцепитель напряжения
Реле или расцепитель, допускающие размыкание или замыкание контактного коммутационного аппарата с выдержкой времени или без нее, когда напряжение на выводах этого реле или расцепителя падает ниже заданной величины
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
under-voltage release
a shunt release which permits a mechanical switching device to open or close, with or without time-delay, when the voltage across the terminals of the release falls below a predetermined value.
[IEC 62271-100, ed. 2.0 (2008-04)
undervoltage release
release which causes a CBE to open, with or without delay, when the voltage across the terminals of the release falls below a predetermined value
[IEC 60934, ed. 3.0 (2000-10)]FR
déclencheur à minimum de tension
déclencheur shunt qui permet l’ouverture ou la fermeture, avec ou sans retard, d’un appareil mécanique de connexion lorsque la tension aux bornes du déclencheur tombe au-dessous d’une valeur prédéterminée.
[IEC 62271-100, ed. 2.0 (2008-04)]
déclencheur à manque de tension
déclencheur qui provoque l'ouverture du DPE avec ou sans retard, lorsque la tension aux bornes du déclencheur tombe au-dessous d'une valeur prédéterminée
[IEC 60934, ed. 3.0 (2000-10)]
Параллельные тексты EN-RU
The undervoltage trip automatically opens a circuit breaker when voltage drops to a value ranging between 35% to 70% of the line voltage.
The operation is instantaneous, and the circuit breaker cannot be reclosed until the voltage returns to 85% of line voltage.
Continuously energized, the undervoltage trip must be operating before the circuit breaker can be closed.
[LS Industrial Systems]Минимальный расцепитель напряжения вызывает срабатывание автоматического выключателя, если линейное напряжение защищаемой цепи падает до 35-70 % от номинального значения.
Срабатывание происходит мгновенно, после чего автоматический выключатель невозможно перевести во включенное положение до тех, пока линейное напряжение защищаемой цепи не повысится до 85 %.
Минимальный расцепитель постоянно находится под напряжением защищаемой цепи и всегда успевает сработать до того, как будет предпринята попытка включения автоматического выключателя.
[Перевод Интент]
В низковольтных автоматических выключателеях минимальный расцепитель напряжения является дополнительной принадлежностью, которая встраивается в гнездо автоматического выключателя
Дополнительные (электрические) принадлежности, встраиваемые в специальные гнезда автоматического выключателя:
1 - Левое гнездо;
2 - Автоматический выключатель;
3 - Правое гнездо.
Рис. LS Industrial SystemsНедопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
- low-voltage release
- under voltage release
- under voltage trip
- under voltage trip coil
- under voltage trip device
- under voltage trip unit
- undervoltage release
- undervoltage trip
- undervoltage trip device
- undervoltage trip unit
- UVT
FR
Русско-французский словарь нормативно-технической терминологии > минимальный расцепитель напряжения
-
2 пониженное напряжение
пониженное напряжение
Напряжение, значение которого меньше допустимого для нормальной работы электротехнических изделий (устройств) и электрооборудования.
[ ГОСТ 23875-88
пониженное напряжение
-
[IEV number 151-15-29]EN
under-voltage
under-tension
voltage the value of which is lower than a specified limiting value
[IEV number 151-15-29]FR
subtension, f
sous-tension, f
manque de tension (terme déconseillé dans ce sens), m
tension électrique de valeur plus petite qu'une valeur limite spécifiée
[IEV number 151-15-29]Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Смотри также
Русско-французский словарь нормативно-технической терминологии > пониженное напряжение
3 ремонтопригодность
ремонтопригодность
Свойство объекта, заключающееся в приспособленности к поддержанию и восстановлению работоспособного состояния путем технического обслуживания и ремонта.
[ ГОСТ 27.002-89]
ремонтопригодность
Свойство объекта, заключающееся в его приспособленности при заданных условиях эксплуатации к поддержанию или восстановлению состояния, в котором он способен выполнять требуемую функцию, путем проведения технического обслуживания и ремонта, выполняемых с использованием установленых процессов и ресурсов.
[ОСТ 45.152-99]
ремонтопригодность
Свойство товара, заключающееся в приспособлении к предупреждению причин возникновения отказов, сбоев, поддержанию работоспособного состояния путем проведения техобслуживания и ремонтов.
[ ГОСТ Р 52104-2003]
ремонтопригодность
По ГОСТ 27. 002-89
В соответствии с ГОСТ 27.002-89 под ремонтопригодностью понимается "свойство объекта, заключающееся в приспособленности к предупреждению и обнаружению причин возникновения его отказов, повреждений и устранению их путем проведения ремонтов и технического обслуживания". При этом следует иметь в виду, что приспособленность объекта к плановым ремонтам относится к его ремонтопригодности.
[ ГОСТ 21623-76]EN
maintainability (performance)
the ability of an item under given conditions of use, to be retained in, or restored to, a state in which it can perform a required function, when maintenance is performed under given conditions and using stated procedures and resources
NOTE – The term "maintainability" is also used as a measure of maintainability performance.
[IEV number 191-02-07]
maintainability
the probability that a given active maintenance action, for an item under given conditions of use can be carried out within a stated time interval, when the maintenance is performed under stated conditions and using stated procedures and resources
NOTE – The term "maintainability" is also used to denote the maintainability performance quantified by this probability.
Source: see 191-02-07
[IEV number 191-13-01]FR
maintenabilité
dans des conditions données d'utilisation, aptitude d'une entité à être maintenue ou rétablie dans un état dans lequel elle peut accomplir une fonction requise, lorsque la maintenance est accomplie dans des conditions données, avec des procédures et des moyens prescrits
NOTE – Le terme "maintenabilité" est aussi employé comme caractéristique de cette aptitude.
[IEV number 191-02-07]
maintenabilité
pour une entité donnée, utilisée dans des conditions données d'utilisation, probabilité pour qu'une opération donnée de maintenance active puisse être effectuée pendant un intervalle de temps donné, lorsque la maintenance est assurée dans des conditions données et avec l'utilisation de procédures et de moyens prescrits
NOTE – Le terme "maintenabilité" est aussi employé pour désigner l'aptitude caractérisée par cette probabilité.
Source: voir 191-02-07
[IEV number 191-13-01]Тематики
- надежность, основные понятия
- ресурсосбережение, обращение с отходами
- система техн. обслуж. и ремонта техники
- тех. обсл. и ремонт средств электросвязи
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ремонтопригодность
4 автоматический выключатель
автоматический выключатель
Механический коммутационный аппарат1), способный включать, проводить и отключать токи при нормальном состоянии электрической цепи, а также включать, проводить в течение заданного времени и автоматически отключать токи в указанном аномальном состоянии электрической цепи, например, при коротком замыкании.
(МЭС 441-14-20)
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]
автоматический выключатель
-
[IEV number 442-05-01]EN
circuit breaker
a mechanical switching device, capable of making, carrying and breaking currents under normal circuit conditions and also making, carrying for a specified time and breaking currents under specified abnormal circuit conditions such as those of short circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
circuit breaker
A device designed to open and close a circuit by nonautomatic means and to open the circuit automatically on a predetermined overcurrent without damage to itself when properly applied within its rating.
NOTE The automatic opening means can be integral, direct acting with the circuit breaker, or remote from the circuit breaker.
Adjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker can be set to trip at various values of current, time, or both within a predetermined range. Instantaneous-trip (as applied to circuit breakers). A qualifying term indicating that no delay is purposely introduced in the tripping action of the circuit breaker.
Inverse-time (as applied to circuit breakers). A qualifying term indicating a delay is purposely introduced in the tripping action of the circuit breaker, which delay decreases as the magnitude of the current increases.
Nonadjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker does not have any adjustment to alter the value of current at which it will trip or the time required for its operation.
Setting (of a circuit breaker). The value of current, time, or both at which an adjustable circuit breaker is set to trip.
[National Electrical Cod]FR
disjoncteur
1) Должно быть контактный коммутационный аппарат
appareil mécanique de connexion capable d’établir, de supporter et d’interrompre des courants dans les conditions normales du circuit, ainsi que d’établir, de supporter pendant une durée spécifiée et d’in- terrompre des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
[Интент]КЛАССИФИКАЦИЯ
- По роду тока
- По напряжению
- По числу полюсов
- По виду корпуса
- По месту установки
- По изолирующей среде
- По установленным расцепителям
- По дополнительным защитам
- По назначению
- По категории применения
- По виду привода взвода пружины
- По выполняемой функции
-
По влиянию монтажного положения
Автоматические выключатели ABB Модульные автоматические выключатели
1. НЕКОТОРЫЕ СВЕДЕНИЯ ОБ АВТОМАТИЧЕСКИХ ВЫКЛЮЧАТЕЛЯХ Автоматический выключатель — это электрический аппарат, который автоматически отключает (и тем самым защищает) электрическую цепь при возникновении в ней аномального режима. Режим становится аномальным, когда в цепи начинает недопустимо изменяться (т. е. увеличиваться или уменьшаться относительно номинального значения) ток или напряжение.
Другими словами (более "инженерно") можно сказать, что автоматический выключатель защищает от токов короткого замыкания и токов перегрузки отходящую от него питающую линию, например, кабель и приемник(и) электрической энергии (осветительную сеть, розетки, электродвигатель и т. п.).
Как правило, автоматический выключатель может применятся также для нечастого (несколько раз в сутки) включения и отключения защищаемых электроприемников (защищаемой нагрузки).
[Интент]Выключатель предназначен для проведения тока в нормальном режиме и отключения тока при коротких замыканиях, перегрузках, недопустимых снижениях напряжения, а также до 30 оперативных включений и отключений электрических цепей в сутки и рассчитан для эксплуатации в электроустановках с номинальным рабочим напряжением до 660 В переменного тока частоты 50 и 60 Гц и до 440 В постоянного тока.
[Типовая фраза из российской технической документации] 2. ПРИНЦИП ДЕЙСТВИЯ Для защиты цепи от короткого замыкания применяется автоматический выключатель с электромагнитным расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Автоматический выключатель устроен таким образом, что сначала необходимо взвести пружину и только после этого его можно включить. У многих автоматических выключателей для взвода пружины необходимо перевести ручку вниз. После этого ручку переводят вверх. При этом замыкаются главные контакты.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Электромагнитный расцепитель;
5 - Сердечник
6 - Катушка
7 - Контактные зажимы автоматического выключателя
На рисунке показан один полюс автоматического выключателя во включенном положении: пружина 1 взведена, а главный контакт 2 замкнут.
Как только в защищаемой цепи возникнет короткое замыкание, ток, протекающий через соответствующий полюс автоматического выключателя, многократно возрастет. В катушке 6 сразу же возникнет сильное магнитное поле. Сердечник 5 втянется в катушку и освободит удерживающее устройство. Под действием пружины 1 главный контакт 2 разомкнется, в результате чего автоматический выключатель отключит и тем самым защитит цепь, в которой возникло короткое замыкание. Такое срабатывание автоматического выключателя происходит практически мгновенно (за сотые доли секунды).
Для защиты цепи от тока перегрузки применяют автоматические выключатели с тепловым расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Принцип действия такой же как и в первом случае, с той лишь разницей, что удерживающее устройство 3 освобождается под действием биметаллической пластины 5, которая изгибается от тепла, выделяемого нагревательным элементом 6. Количество тепла определяется током, протекающим через защищаемую цепь.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Тепловой расцепитель
5 - Биметаллическая пластина
6 - Нагревательный элемент
7 - Контактные зажимы автоматического выключателя
[Интент]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Обобщающие термины
Действия
- включение автоматического выключателя
- оперирование автоматического выключателя
- отключение автоматического выключателя
- срабатывание автоматического выключателя
EN
- auto-cutout
- automatic circuit breaker
- automatic cutout
- automatic switch
- breaker
- CB
- circuit breaker
- circuit-breaker
- cutout
DE
FR
Смотри также
Русско-французский словарь нормативно-технической терминологии > автоматический выключатель
5 автоматический выключатель постоянного тока
автоматический выключатель постоянного тока
-En
d.c. circuit-breaker
switching device capable of making, carrying and breaking direct currents under normal circuit conditions and also making, carrying (up to a specified limit and for a specified time) and breaking currents under specified abnormal conditions, such as those of short-circuit.
[IEC 61992-1, ed. 2.0 (2006-02)]Fr
disjoncteur à courant continu
appareil de connexion capable d'établir, de supporter et d'interrompre des courants continus dans les conditions normales du circuit ainsi que d'établir, de supporter (jusqu'à une limite spécifiée et pendant une durée spécifiée) et d'interrompre des courants dans des conditions anormales spécifiées du circuit, telles que celles du court-circuit.
[IEC 61992-1, ed. 2.0 (2006-02)]Тематики
Классификация
>>>Обобщающие термины
EN
- circuit-breaker for direct current
- circuit-breaker for direct current applications
- d.c. circuit breaker
- d.c. circuit-breaker
- direct current circuit breaker
- direct current circuit-breaker
FR
Русско-французский словарь нормативно-технической терминологии > автоматический выключатель постоянного тока
6 автоматический выключатель, управляемый дифференциальным током
- interrupteur à courant différentiel résiduel
- DPR
- disjoncteur à protection par courant différentiel résiduel incorporée
автоматический выключатель, управляемый дифференциальным током
Контактный коммутационный аппарат, предназначенный для включения, проведения и отключения токов при нормальных условиях электрической цепи, а также отключения электрической цепи в случае, когда значение дифференциального тока достигает заданной величины в определенных условиях.
[Перевод Интент]EN
residual current-operated circuit-breaker
mechanical switching device designed to make, carry and break currents under normal service conditions and to cause the opening of the contacts when the residual current attains a given value under specified conditions.
[IEC 62335, ed. 1.0 (2008-07)]FR
interrupteur à courant différentiel résiduel
appareil mécanique de connexion destiné à établir, supporter et couper des courants dans les conditions de service normales et à provoquer l'ouverture des contacts quand le courant différentiel atteint, dans des conditions spécifiées, une valeur donnée.
[IEC 62335, ed. 1.0 (2008-07)]Недопустимые, нерекомендуемые
- автоматический выключатель остаточных токов
- автоматический выключатель с функцией защиты от тока утечки
- автоматический выключатель, управляемый остаточным током
Тематики
Классификация
>>>Обобщающие термины
Синонимы
EN
- CBR
- circuit breaker incorporating residual current protection
- circuit-breaker incorporating residual current protection
- circuit-breaker with integrated residual current protection
- earth leakage circuit breaker
- ELCB
- RCCB
- residual current circuit breaker
- residual current circuit-breaker
- residual current-operated circuit breaker
- residual current-operated circuit-breaker
FR
Русско-французский словарь нормативно-технической терминологии > автоматический выключатель, управляемый дифференциальным током
7 воздействующая величина электрического реле
- Grandeur d’alimentation
- grandeur d'alimentation
воздействующая величина электрического реле
Электрическая величина, которая одна или в сочетании с другими электрическими величинами должна быть приложена к электрическому реле в заданных условиях для достижения ожидаемого функционирования
[ ГОСТ 16022-83]EN
energizing quantity
an electrical quantity (either current or voltage) which alone, or in combination with other such quantities, applied to a relay under specified conditions enables it to fulfil its purpose
[IEV number 446-12-01]
energizing quantity (for elementary relays)electrical quantity which, when applied to the input circuit of an elementary relay under specified conditions, enables it to fulfill its purpose
NOTE – For elementary relays the energizing quantity is usually a voltage. Therefore, the input voltage as energizing quantity is used in the definitions given below. Where a relay is energized by a given current instead, the respective terms and definitions apply with "current" used instead of "voltage".
[IEV number 444-03-01]FR
grandeur d'alimentation
grandeur électrique, courant ou tension, qui, seule ou en combinaison avec d'autres grandeurs électriques, courant ou tension, doit être appliquée dans des conditions spécifiées à un relais pour en obtenir le comportement attendu
[IEV number 446-12-01]
grandeur d'alimentation (pour les relais élémentaires), f
grandeur électrique qui, appliquée au circuit d'entrée d'un relais élémentaire dans des conditions spécifiées, lui permet d'accomplir sa fonction
NOTE – Pour les relais élémentaires, la grandeur d'alimentation est en général une tension. En conséquence, on utilise la tension d'entrée comme grandeur d'alimentation dans les définitions données ci-dessous. Lorsqu'un relais est alimenté par un courant, les termes et définitions respectifs sont à utiliser avec le terme "courant" au lieu du terme "tension".
[IEV number 444-03-01]Тематики
Классификация
>>>EN
DE
FR
49. Воздействующая величина электрического реле
D. Eingangsgrösse
Е. Energizing quantity
F. Grandeur d’alimentation
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > воздействующая величина электрического реле
8 входное полное сопротивление
входное полное сопротивление
-
[IEV number 312-06-18]EN
input impedance
impedance of the input circuit measured between the input terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the input circuit is such that the instantaneous value of the current flowing into the input terminals is a non-linear function of the instantaneous value of the input voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual input circuit, is sometimes called the "equivalent input impedance".
[IEV number 312-06-18]FR
impédance du circuit d'entrée
impédance du circuit d'entrée entre les bornes d'entrée dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit d'entrée est tel que la valeur instantanée du courant traversant les bornes d'entrée est une fonction non linéaire de la valeur instantanée de la tension d'entrée dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit d'entrée réel, est parfois appelée "impédance équivalente d'entrée".
[IEV number 312-06-18]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > входное полное сопротивление
9 выключатель (контактный)
выключатель (контактный)
Контактный коммутационный аппарат, способный включать, проводить и отключать токи в нормальных условиях, в том числе при оговоренных рабочих перегрузках, а также в течение установленного времени проводить ток в оговоренных аномальных условиях, например при коротком замыкании.
МЭК 60050(441-14-10)
Примечание. Выключатель может быть способен включать, но не отключать ток короткого замыкания.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
(mechanical) switch
a mechanical switching device capable of making, carrying and breaking currents under normal circuit conditions which may include specified operating overload conditions and also carrying for a specified time currents under specified abnormal circuit conditions such as those of short circuit
NOTE – A switch may be capable of making but not breaking short-circuit currents.
[IEV number 441-14-10]FR
interrupteur (mécanique)
appareil mécanique de connexion capable d'établir, de supporter et d'interrompre des courants dans les conditions normales du circuit y compris éventuellement les conditions spécifiées de surcharge en service, ainsi que de supporter pendant une durée spécifiée des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit
NOTE – Un interrupteur peut être capable d'établir des courants de court-circuit mais n'est pas capable de les couper
[IEV number 441-14-10]Недопустимые, нерекомендуемые
Тематики
- выключатель, переключатель
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выключатель (контактный)
10 выходное полное сопротивление
выходное полное сопротивление
-
[IEV number 312-06-19]EN
output impedance
impedance of the output circuit measured between the output terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the output circuit is such that the instantaneous value of the current flowing into the output terminals is a non-linear function of the instantaneous value of the output voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual output circuit, is sometimes called the "equivalent output impedance".
[IEV number 312-06-19]FR
impédance du circuit de sortie
impédance du circuit de sortie entre les bornes de sortie dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit de sortie est tel que la valeur instantanée du courant traversant les bornes de sortie est une fonction non linéaire de la valeur instantanée de la tension de sortie dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit de sortie réel, est parfois appelée "impédance équivalente de sortie".
[IEV number 312-06-19]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выходное полное сопротивление
11 гигроскопичная лента
гигроскопичная лента
водонабухающая лента
лента, применяемая под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-16]EN
water blocking tape
swelling tape
tape applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-16]FR
ruban d'étanchéité
ruban gonflant
ruban appliqué sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-16]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellband, n
FR
Русско-французский словарь нормативно-технической терминологии > гигроскопичная лента
12 гигроскопичная пудра
гигроскопичная пудра
водонабухающая пудра
порошковый наполнитель, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-14]EN
water blocking powder
swelling powder
powder applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-14]FR
poudre d'étanchéité
poudre gonflante
poudre appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-14]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellpulver, n
FR
Русско-французский словарь нормативно-технической терминологии > гигроскопичная пудра
13 гигроскопичный клей
гигроскопичный клей
водонабухающий клей
клей, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-17]EN
water blocking glue
swelling glue
glue applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-17]FR
matière d'étanchéité
matière appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-17]
Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellmasse, f
FR
Русско-французский словарь нормативно-технической терминологии > гигроскопичный клей
14 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
15 зажим под гайку
зажим под гайку
Зажим винтового типа, в котором проводник прижимают гайкой. Силу прижима могут прилагать непосредственно фасонной гайкой или через промежуточную деталь, например шайбу, прижимную пластину или устройство для самоотвинчивания.
[ ГОСТ Р 51324.1-2005]EN
stud terminal
terminal with screw clamping in which the conductor is clamped under a nut. The clamping pressure may be applied directly by a suitably shaped nut or through an intermediate part, such as a washer, clamping plate or anti-spread device
[IEC 60669-1, ed. 3.0 (1998-02)]
stud terminal
a screw-type terminal in which the conductor is clamped under a nut
NOTE – The clamping pressure can be applied directly by a suitably shaped nut or through an intermediate part, such as a washer, a clamping plate or an anti-spread device.
[IEV number 442-06-23]FR
borne à goujon fileté
organe de serrage à vis dans lequel l'âme d'un conducteur est serrée sous un écrou. La pression de serrage peut être appliquée directement par un écrou de forme appropriée ou au moyen d'une partie intermédiaire, telle qu'une rondelle, une plaquette ou un dispositif empêchant le conducteur ou ses brins de s'échapper
[IEC 60669-1, ed. 3.0 (1998-02)]
borne à goujon fileté
borne à vis dans laquelle l'âme d'un conducteur est serrée sous un écrou
NOTE – La pression de serrage peut être appliquée directement par un écrou de forme appropriée ou au moyen d'une partie intermédiaire, tel qu'une rondelle, une plaquette ou un dispositif empêchant le conducteur ou ses brins de s'échapper.
[IEV number 442-06-23]Тематики
- вывод, зажим электрический
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > зажим под гайку
16 заземлитель (коммутационный аппарат)
заземлитель
Контактный коммутационный аппарат, используемый для заземления частей цепи, способный выдерживать в течение нормированного времени токи при ненормальных условиях, таких как короткое замыкание, но не предусмотренный для проведения тока при нормальных условиях в цепи.
Примечания
1 Заземлитель может обладать включающей способностью при коротком замыкании.
2 Заземлитель на номинальное напряжение 110 кВ и выше может отключать (коммутировать) и проводить наведенные токи.
[ ГОСТ Р 52726-2007]
выключатель заземления
Механический 1) коммутационный аппарат для заземления частей электрической цепи, способный выдерживать электрические токи заданной продолжительности при ненормальных режимах, например при коротких замыканиях, но не предназначенный для пропускания электрического тока в нормальных режимах работы электрической цепи.
Примечание - Выключатель может быть стойким к токам короткого замыкания.
[ ГОСТ Р МЭК 60050-195-2005]EN
earthing switch
mechanical switching device for earthing parts of an electric circuit, capable of withstanding for a specified duration electric currents under abnormal conditions such as those of short-circuit, but not required to carry electric current under normal conditions of the electric circuit
NOTE – An earthing switch can have a short circuit making capacity.
Source: 441-14-11 MOD, 605-02-43 MOD
[IEV number 195-02-34]FR
connecteur de terre
appareil mécanique de connexion utilisé pour mettre à la terre des parties d'un circuit électrique, capable de supporter, pendant une durée spécifiée, des courants dans des conditions anormales telles que celles de court-circuit, mais non prévu pour transporter le courant électrique dans les conditions normales du circuit électrique
NOTE – Un connecteur de terre peut avoir un pouvoir de fermeture en court circuit.
Source: 441-14-11 MOD, 605-02-43 MOD
[IEV number 195-02-34]1) Должно быть контактный
[Интент]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- заземление
- электробезопасность
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > заземлитель (коммутационный аппарат)
17 значение величины срабатывания (возврата) электрического реле
значение величины срабатывания (возврата) электрического реле
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
[ ГОСТ 16022-83]EN
switching value
the value of the input energizing quantity (or characteristic quantity) at which a relay switches under specified conditions
NOTE – These specified conditions can be expressed by using one of the adjectives defined under the items 446-13-27 to 446-13-29.
[IEV number 446-13-24]FR
valeur de commutation
valeur de la grandeur d'alimentation d'entrée ou de la grandeur caractéristique, pour laquelle un relais commute dans des conditions spécifiées
NOTE – Ces conditions spécifiées peuvent être exprimées par l'un des qualificatifs définis de 446-13-27 à 446-13-29.
[IEV number 446-13-24]Тематики
Классификация
>>>EN
DE
FR
71. Значение величины срабатывания (возврата) электрического реле
D. Ansprechwert
Е. Operate value
F. Valeur de fonctionnement
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > значение величины срабатывания (возврата) электрического реле
18 контролируемый признак
контролируемый признак
Характеристика объекта, подвергаемая контролю.
[ ГОСТ 16504-81]Тематики
EN
FR
E. Characteristic under control
F. Caractère a contrôler
Характеристика объекта, подвергаемая контролю
Источник: ГОСТ 16504-81: Система государственных испытаний продукции. Испытания и контроль качества продукции. Основные термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > контролируемый признак
19 коэффициент мощности
коэффициент мощности
Скалярная величина, равная отношению активной мощности двухполюсника к полной мощности.
[ ГОСТ Р 52002-2003]
коэффициент мощности (цепи)
Отношение активного сопротивления к полному сопротивлению при промышленной частоте в эквивалентной цепи, которая считается состоящей из последовательно соединенных индуктивного и активного сопротивлений
[ ГОСТ Р 52565-2006]EN
power factor
under periodic conditions, ratio of the absolute value of the active power P to the apparent power S:
NOTE – Under sinusoidal conditions, the power factor is the absolute value of the active factor.
[IEV ref 131-11-46]FR
facteur de puissance, m
en régime périodique, rapport de la valeur absolue de la puissance active P à la puissance apparente S:
NOTE – En régime sinusoïdal, le facteur de puissance est la valeur absolue du facteur de puissance active.
[IEV ref 131-11-46]
Для синусоидального тока коэффициент мощности равен косинусу угла сдвига фаз между напряжением и током, т. е. равен Cos φ.
После того, как стали массово применяться такие нелинейные нагрузки, как компьютеры и другое офисное и телекоммуникационное оборудование, термин коэффициент мощности перестал быть синонимом термина Cos φ.Тематики
- качество электрической энергии
- электромагнитная совместимость
- электроснабжение в целом
- электротехника, основные понятия
Близкие понятия
Действия
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > коэффициент мощности
20 механическая износостойкость контактного аппарата
- endurance mécanique, f
механическая износостойкость контактного аппарата
Способность контактного аппарата выполнять в определенных условиях определенное число операций без тока в цени главных и свободных контактов, оставаясь после этого в предусмотренном состоянии.
[ ГОСТ 17703-72]EN
mechanical endurance
number of cycles under specified conditions with unloaded contact(s)
[IEC 61810-1, ed. 3.0 (2008-02)]
mechanical endurance
number of cycles until relay failure, with unloaded output circuit(s) and under specified operating conditions
[IEV 444-07-10]FR
endurance mécanique, f
nombre de manœuvres avant défaillance du relais, le ou les circuits de sortie n'étant pas chargés et dans des conditions de fonctionnement spécifiées
[IEV 444-07-10]По стойкости к механическому износу аппарат характеризуется числом (указанным в стандарте на соответствующий аппарат) циклов оперирования без нагрузки (т. е. при обесточенных главных контактах), которые он должен осуществить, прежде чем возникнет необходимость обслуживания или замены каких-либо механических частей; однако может допускаться нормальное, по инструкциям изготовителя, обслуживание аппаратов, для которых оно предусмотрено.
Каждый цикл оперирования состоит из одного замыкания с последующим размыканием.
<>[<> ГОСТ Р 50030. 1-2000]Тематики
- аппарат, изделие, устройство...
- контакт
EN
DE
FR
- endurance mécanique, f
Русско-французский словарь нормативно-технической терминологии > механическая износостойкость контактного аппарата
См. также в других словарях:
Under — Un der, prep. [AS. under, prep. & adv.; akin to OFries. under, OS. undar, D. onder, G. unter, OHG. untar, Icel. undir, Sw. & Dan. under, Goth. undar, L. infra below, inferior lower, Skr. adhas below. [root]201. Cf. {Inferior}.] 1. Below or lower … The Collaborative International Dictionary of English
under — [un′dər] prep. [ME < OE, akin to Ger unter < IE * ṇdhos, *ṇdheri, under > L infra, below] 1. in, at, or to a position down from; lower than; below [shoes under the bed, under a blazing sun] 2. beneath the surface of [under water] 3.… … English World dictionary
under — (prep., adv.) O.E. under, from P.Gmc. *under (Cf. O.Fris. under, Du. onder, O.H.G. untar, Ger. unter, O.N. undir, Goth. undar), from PIE *ndhero lower (Cf. Skt. adhah below; Avestan athara lower; … Etymology dictionary
Under — Série Logo de la série Scénario Christophe Bec Dessin … Wikipédia en Français
under — *under germ., Adverb, Präposition: nhd. unter, zwischen; ne. under, between; Rekontruktionsbasis: got., an., ae., afries., anfrk., as., ahd.; Etymologie … Germanisches Wörterbuch
Under — Un der, adv. In a lower, subject, or subordinate condition; in subjection; used chiefly in a few idiomatic phrases; as, to bring under, to reduce to subjection; to subdue; to keep under, to keep in subjection; to control; to go under, to be… … The Collaborative International Dictionary of English
Under — Un der, a. Lower in position, intensity, rank, or degree; subject; subordinate; generally in composition with a noun, and written with or without the hyphen; as, an undercurrent; undertone; underdose; under garment; underofficer; undersheriff.… … The Collaborative International Dictionary of English
under — {{hw}}{{under}}{{/hw}}(sempre seguito da un num. card.) A s. m. e f. spec. al pl. Atleta al disotto di una data età: gli under 21. B agg. ; anche s. f. Squadra formata di atleti al disotto di una data età: la nazionale under 21; l under 21 ha… … Enciclopedia di italiano
under- — [ʌndə US dər] prefix 1.) less of an action or quality than is correct, needed, or desired ▪ underdevelopment ▪ undercooked cabbage 2.) going under something ▪ an underpass (=a road or path that goes under another road) 3.) inside or beneath other … Dictionary of contemporary English
under- — [ʌndə US dər] prefix 1.) less of an action or quality than is correct, needed, or desired ▪ underdevelopment ▪ undercooked cabbage 2.) going under something ▪ an underpass (=a road or path that goes under another road) 3.) inside or beneath other … Dictionary of contemporary English
under- — [ ʌndər ] prefix 1. ) not enough: used with many nouns, verbs, and adjectives: under exposed under nourished 2. ) below: used with many nouns: underpass underwater underfloor heating 3. ) less powerful or important: used with some nouns: an under … Usage of the words and phrases in modern English
Перевод: с русского на французский
с французского на русский- С французского на:
- Русский
- С русского на:
- Все языки
- Английский
- Датский
- Итальянский
- Немецкий
- Нидерландский
- Персидский
- Французский
- Шведский
- Эстонский