-
1 нефтесвязующее вещество
нефтесвязующее вещество
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
oil binding agent
Highly absorbent agents used for physically removing spilled oil in case of leakages and oil accidents occurring in water bodies, industry, work-shops, on roads, etc. Materials that have been found useful for this service vary from simple, naturally occurring materials such as straw, sawdust, and peat to synthetic agents, such as polyurethane foam and polystyrene powder. (Source: FUNKE / PZ)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > нефтесвязующее вещество
-
2 автоматическая разгрузка
- Lastabwurfschutz, m
автоматическая разгрузка
Защита, предназначенная для снижения нагрузки системы в случае возникновения анормального режима, например, при понижении частоты.
[Разработка типовых структурных схем микропроцессорных устройств РЗА на объектах ОАО "ФКС ЕЭС". Пояснительная записка. Новосибирск 2006 г.]EN
load-shedding protection
protection intended to decrease the system load in the case of an abnormal condition such as a frequency reduction
[IEV ref 448-14-36]FR
protection de délestage
protection destinée à réduire la charge du réseau en cas de situation anormale telle qu'une baisse de fréquence
[IEV ref 448-14-36]Тематики
EN
DE
- Lastabwurfschutz, m
FR
Русско-немецкий словарь нормативно-технической терминологии > автоматическая разгрузка
-
3 переключающий контакт
переключающий контакт электрической цепи
Контакт электрической цепи, который размыкает одну электрическую цепь и замыкает другую при заданном действии устройства
[ ГОСТ 14312-79]
переключающий контакт
switching contact
Механический контакт, предназначенный для замыкания и размыкания электрической цепи.
[ ГОСТ Р МЭК 60050-426-2006]EN
change-over contact
combination of two contact circuits with three contact members, one of which is common to the two contact circuits; such that when one of these contact circuits is open, the other is closed
[IEV number 444-04-19]FR
contact à deux directions, m
contact inverseur (déconseillé), m
combinaison de deux circuits de contact comprenant trois éléments de contact, l'un d'eux étant commun aux deux circuits de contact ; de telle manière que lorsque l'un des circuits de contact est ouvert, l'autre est fermé
[IEV number 444-04-19]Параллельные тексты EN-RU CO contact
Compound contact consisting of a NO (make) contact and a NC (break) contact with a common terminal. On changing the switch position, the contact previously closed opens first followed by the closing of the contact that was previously open. Note: in case of a switching arc the NO and NC contact may be temporarily electrically connected.
[Tyco Electronics]Переключающий контакт
Контакт, объединяющий в себе замыкающий и размыкающий контакты с общим выводом. При изменении коммутационного положения сначала размыкается ранее замкнутый контакт, затем замыкается контакт, который до этого был разомкнут. Примечание. Если в процессе коммутации возникнет дуга между размыкающим и замыкающим контактами, то между ними может установиться кратковременная электрическая связь.
[Перевод Интент]Недопустимые, нерекомендуемые
Тематики
Обобщающие термины
Синонимы
EN
- C/O
- change-over contact
- changeover contact
- CO contact
- double-throw contact
- make-and-break contact
- switching contact
- transfer contact
- two-way contact
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > переключающий контакт
-
4 промежуточный адаптер (для эдектроустановочных изделий)
промежуточный адаптер (для эдектроустановочных изделий)
-
[IEV number 442-03-21]EN
intermediate adaptor (for accessories)
adaptor which allows the connection of one or more types of plug to a socket-outlet via a control device such as a dimmer, clock switch, photo-electric switch, etc., which can be either integral with the intermediate adaptor or connected to it by a flexible cable, and in which case can be either rewireable or non-rewireable
[IEV number 442-03-21]FR
adaptateur intermédiaire (pour le petit appareillage)
adaptateur qui permet la connexion d'un ou de plusieurs types de fiches à un socle de prise de courant au moyen d'un dispositif de commande tel qu'un gradateur, un interrupteur horaire, un interrupteur photoélectrique, etc., qui peut être soit partie intégrante de l'adaptateur intermédiaire soit connecté à ce dernier au moyen d'un câble souple, et qui dans ce cas peut être démontable ou non
[IEV number 442-03-21]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > промежуточный адаптер (для эдектроустановочных изделий)
-
5 проходной изолятор
проходной изолятор
Изолятор, предназначенный для провода токоведущих элементов через стенку, имеющую другой электрический потенциал.
[ ГОСТ 27744-88]
проходной изолятор
-
[IEV number 151-15-40]EN
(insulating) bushing
insulator forming a passage for a conductor through a non-insulating partition
[IEV number 151-15-40]
bushing
A bushing is a cyclindrical insulating component, usually made of ceramic, that houses a conductor. It enables a conductor to pass through a grounded enclosure, such as a transformer tank (the physical shell of a transformer), a wall or other physical barrier, to connect electrical installations. In the case of a transformer, bushings protect the conductors that connect a transformer’s core to the power system it serves through channels in the transformer’s housing.
[ABB. Glossary of technical terms. 2010]FR
isolateur de traversée, m
traversée, f
isolateur permettant le passage d'un conducteur à travers une paroi non isolante
[IEV number 151-15-40]
Проходной изоляторПараллельные тексты EN-RU
The circuit breaker is connected via bushings to the rest of the switchgear at the flanges provided.
[Siemens]С другими частями распределительного устройства силовой выключатель соединяется через проходные изоляторы, закрепленные в его фланцах.
[Перевод Интент]Тематики
Классификация
>>>Обобщающие термины
EN
DE
FR
- isolateur de traversée, m
- traversée
Русско-немецкий словарь нормативно-технической терминологии > проходной изолятор
-
6 пуск переключением со звезды на треугольник
пуск переключением со звезды на треугольник
-EN
star-delta starting
the process of starting a three-phase motor by connecting it to the supply with the primary winding initially connected in star, then reconnected in delta for the running condition
[IEV number 411-52-16]FR
démarrage étoile-triangle
mode de démarrage d'un moteur triphasé à tension réduite, consistant à relier à la source à tension constante les enroulements statoriques, d'abord en couplage étoile, puis à passer au couplage triangle pour le fonctionnement normal
[IEV number 411-52-16]Magnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Y/Δ changeover node - Узел переключения со звезды на треугольник
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Contactor KΔ - Контактор KΔ
Contactor KY- Контактор KY
Параллельные тексты EN-RU Star-delta Y/Δ starting
Star-delta starting is the best known system and perhaps the commonest starting system at reduced voltage; it is used to start the motor reducing the mechanical stresses and limiting the current values during starting; on the other hand, it makes available a reduced inrush torque.This system can be used for motors with terminal box with 6 terminals and double supply voltage.
It is particularly suitable for no-load starting or with low and constant load torque or lightly increasing load torque, such as in the case of fans or low power centrifugal pumps.
Making reference to the diagram of Figure 6, the starting modality foresees the initial phase with star-connection of the windings to be realized through the closing of the circuit-breaker, of the line contactor KL and of the star contactor KY.
After a suitable predetermined period of time, the opening of the contactor KY and the closing of KΔ allow switching to delta-connection, which is also the configuration of normal running position.
[ABB]Пуск переключением со звезды на треугольник
Пуск переключением со звезды на треугольник является самым известным способом и, возможно, самой распространенной схемой пуска на пониженном напряжении. С одной стороны, этот способ используется для снижения механических нагрузок и ограничения пускового тока, а с другой - обеспечивает уменьшение пускового момента.Такая возможность может быть реализована в двигателях с шестью зажимами в выводной коробке, что позволяет питать его от двух напряжений.
Особенно этот способ подходит для ненагруженного пуска и пуска с низким постоянным или немного увеличивающимся вращающим моментом, например, для пуска вентиляторов или маломощных центробежных насосов.
Схема пуска переключением со звезды на треугольник представлена на рисунке 6. В начальный момент пуска обмотки статора соединяют звездой путем замыкания контактов автоматического выключателя, линейного контактора KL и контактора KY со схемой "звезда".
По истечении заданного времени контакты контактора KY размыкаются и замыкаются контакты контактора КΔ со схемой треугольник.
В результате выполняется переключение обмоток статора со схемы «звезда» на схему «треугольник».
Обе схемы соединения обмоток являются схемами нормального рабочего режима.
[Перевод Интент]Тематики
Обобщающие термины
EN
- star-delta starting
- Y/Δ starting
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > пуск переключением со звезды на треугольник
-
7 температура окружающей среды
- Umgebungstemperatur, f
температура окружающей среды
Средняя температура воздуха или другой среды около оборудования.
Примечание - В процессе измерения температуры окружающей среды измерительный прибор (зонд) должен быть экранирован от сквозняков и нагрева излучением.
[ ГОСТ Р МЭК 60050-826-2009]
температура окружающей среды
Температура воздуха или другой среды в непосредственной близости от оборудования или компонента.
[ ГОСТ Р МЭК 60050-426-2006]
температура окружающей среды
Предполагают, что под температурой окружающей среды понимают воздействующие факторы со стороны всего другого оборудования, установленного в том же помещении.
Температура окружающей среды, которую следует учитывать применительно к оборудованию, - это температура в том месте, где оно должно быть установлено, с учетом влияния другого оборудования и источников тепла в том же месте в процессе работы без учета тепла от устанавливаемого оборудования
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
температура окружающей среды
Температура воздуха или среды в том месте, где должно быть использовано оборудование.
[ ГОСТ Р МЭК 60204-1-2007]EN
ambient temperature
average temperature of air or another medium in the vicinity of the equipment
NOTE – During the measurement of the ambient temperature the measuring instrument/probe should be shielded from draughts and radiant heating.
[IEV number 826-10-03]
ambient temperature
temperature of the air or other medium where the equipment is to be used
[IEC 60204-1-2006]FR
température ambiante, f
température moyenne de l'air ou du milieu au voisinage du matériel
NOTE – Pendant la mesure de la température ambiante il est recommandé que l'instrument/la sonde de mesure soit protégée des courants d'air et de la chaleur rayonnée.
[IEV number 826-10-03]Параллельные тексты EN-RU
The temperate of each module of a Molded Case Circuit Breaker is the sum of temperature increase by conduction and ambient temperature and if the ambient temperature exceeds 40°C the passing current needs to be reduced so that the temperature of such element as internal insulator of MCCB exceed the maximum allowable temperature.
[LS Industrial Systems]Температура частей автоматического выключателя в литом корпусе равна температуре окружающей среды плюс температура, определяемая количеством теплоты, выделяемой при протекании электрического тока. Если автоматический выключатель эксплуатируется при температуре окружающей среды, превышающей 40 °C, то следует учитывать, что номинальный ток такого выключателя будет немного меньше. Учет этого обстоятельства позволит избежать недопустимого нагрева частей автоматического выключателя, выполненных из изоляционного материала.
[Перевод Интент]Тематики
EN
DE
- Umgebungstemperatur, f
FR
- température ambiante, f
Русско-немецкий словарь нормативно-технической терминологии > температура окружающей среды
См. также в других словарях:
Case modding — Case modification (commonly referred to as case modding where an individual project is referred to as a case mod) is the modification of a computer chassis (often just referred to as the case), or a video game console chassis. Modifying a… … Wikipedia
Case-control — is a type of epidemiological study design. Case control studies are used to identify factors that may contribute to a medical condition by comparing subjects who have that condition (the cases ) with patients who do not have the condition but are … Wikipedia
Case (goods) — A case of some merchandise is a collection of items packaged together. In the United States, typically a standard case contains a certain number of items depending on what the merchandise is. For consumer foodstuffs such as canned goods, soda,… … Wikipedia
Case of first impression — A case of first impression (known as primae impressionis in Latin) is a legal case in which there is no binding authority on the matter presented. A case of first impression may be a case of first impression in only a particular jurisdiction. In… … Wikipedia
case reserved — A statement in writing of the facts proved on the trial of a cause, drawn up and settled by the attorneys and counsel for the respective parties under the supervision of the judge, for the purpose of having certain points of law, which arose at… … Black's law dictionary
case reserved — A statement in writing of the facts proved on the trial of a cause, drawn up and settled by the attorneys and counsel for the respective parties under the supervision of the judge, for the purpose of having certain points of law, which arose at… … Black's law dictionary
Case hardening — or surface hardening is the process of hardening the surface of a metal, often a low carbon steel, by infusing elements into the material s surface, forming a thin layer of a harder alloy. Case hardening is usually done after the part in question … Wikipedia
Case Western Reserve University — Motto Thinking Beyond the Possible Established WRU: 1826 CIT: 1880 CWRU: 1967 Type … Wikipedia
Case grammar — is a system of linguistic analysis, focusing on the link between the valence of a verb and the grammatical context it requires, created by the American linguist Charles J. Fillmore in (1968), in the context of Transformational Grammar. This… … Wikipedia
Case-based reasoning — (CBR), broadly construed, is the process of solving new problems based on the solutions of similar past problems. An auto mechanic who fixes an engine by recalling another car that exhibited similar symptoms is using case based reasoning. A… … Wikipedia
case — case1 [kās] n. [ME & OFr cas, an event < L casus, a chance, lit., falling, pp. of cadere, to fall < IE base * k̑ad , to fall > Sans s̍ad , to fall off] 1. an example, instance, or occurrence [a case of carelessness, a case of measles] 2 … English World dictionary