-
1 нефтесвязующее вещество
нефтесвязующее вещество
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
oil binding agent
Highly absorbent agents used for physically removing spilled oil in case of leakages and oil accidents occurring in water bodies, industry, work-shops, on roads, etc. Materials that have been found useful for this service vary from simple, naturally occurring materials such as straw, sawdust, and peat to synthetic agents, such as polyurethane foam and polystyrene powder. (Source: FUNKE / PZ)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > нефтесвязующее вещество
-
2 автоматическая разгрузка
автоматическая разгрузка
Защита, предназначенная для снижения нагрузки системы в случае возникновения анормального режима, например, при понижении частоты.
[Разработка типовых структурных схем микропроцессорных устройств РЗА на объектах ОАО "ФКС ЕЭС". Пояснительная записка. Новосибирск 2006 г.]EN
load-shedding protection
protection intended to decrease the system load in the case of an abnormal condition such as a frequency reduction
[IEV ref 448-14-36]FR
protection de délestage
protection destinée à réduire la charge du réseau en cas de situation anormale telle qu'une baisse de fréquence
[IEV ref 448-14-36]Тематики
EN
DE
- Lastabwurfschutz, m
FR
Русско-французский словарь нормативно-технической терминологии > автоматическая разгрузка
-
3 вакуумный контактор (пускатель)
вакуумный контактор (пускатель)
Контактор (пускатель), у которого главные контакты размыкаются и замыкаются внутри оболочки с сильно разреженной атмосферой.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]EN
vacuum contactor (or starter)
contactor (or starter) in which the main contacts open and close within a highly evacuated envelope
[IEC 60947-4-1, ed. 3.0 (2009-09)]FR
contacteur (ou démarreur) sous vide
contacteur (ou démarreur) dont les contacts principaux s'ouvrent et se ferment à l'intérieur d'une enveloppe à basse pression
[IEC 60947-4-1, ed. 3.0 (2009-09)]Параллельные тексты EN-RU
Vacuum contactors are mainly used for the switching of motors, transformers, capacitors in AC power lines.
They can be installed in multi-stack cubicles.
A vacuum contactor comprises several assemblies such as switching mechanism including vacuum interrupters, magnetic actuator, high strength molded front cover and auxiliary devices.
Actuating is available either at instantaneous or continuous excitation.
[LS Industrial Systems]Вакуумные контакторы предназначены в основном для коммутации силовых цепей переменного тока электродвигателей, трансформаторов и конденсаторов.
Контакторы пригодны для установки в комплектные устройства в несколько ярусов.
Вакуумный контактор состоит из следующих узлов: коммутационный механизм с вакуумной дугогасительной камерой, электромагнитный привод, прочная пластмассовая передняя панель и вспомогательные устройства.
Включение и отключение контактора возможно как подачей кратковременного, так и непрерывного сигнала на электромагнитный привод.
[Перевод Интент]
Вакуумный контактор среднего напряжения выдвижного исполнения с предохранителями
Рис. LS Industrial Systems1
Передняя панель
2
Окно проверки состояния предохранителя
3
Электрический соединитель
4
Unlock button (Interlock lever)
Кнопка разблокировки рычага
5
Ручка (предназначена для того, чтобы вдвигать и выдвигать контактор)
6
ON/OFF indicator
Указатель коммутационного положения контактора (ВКЛ/ОТКЛ.)
7
Счетчик операционных циклов
8
Кнопка ручного отключения контактора
10
Выдвижной лоток
11
Блокировочный рычаг
12
Блокировочная кнопка
13
Hole for Interlock lever insertion
Отверстие для вставки блокировочного рычага
14
Test/Run indicator
Индикатор положений Испытательное/Присоединенное
15
Корзина
16
Конденсаторный источник питания
17
Кожух предохранителя
Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- контакторы и пускатели
EN
FR
Русско-французский словарь нормативно-технической терминологии > вакуумный контактор (пускатель)
-
4 интергармоника
интергармоника
Интергармониками называют токи (напряжения) частота которых не кратна частоте основной гармоники.EN
interharmonic component
sinusoidal component of a periodic quantity having a an interharmonic frequency
NOTE 1 For brevity, such a component may be referred to simply as an interharmonic.
NOTE 2 For practical analysis, an approximation of the periodicity may be necessary.
NOTE 3 The value is normally expressed as an r.m.s. value.
NOTE 4 As stated in IEC 61000-4-7, the time window has a width of 10 fundamental periods (50 Hz systems) or 12 fundamental periods (60 Hz systems), i.e. approximately 200 ms. The difference in frequency between two consecutive interharmonic components is, therefore, approximately 5 Hz. In the case of other fundamental frequencies, the time window should be selected between 6 fundamental periods (approximately 1 000 ms at 6 Hz) and 18 fundamental periods (approximately 100 ms at 180 Hz).
[IEC 60146-1-1, ed. 4.0 (2009-06)]FR
composante interharmonique
composante sinusoïdale d’une grandeur périodique dont la fréquence est une fréquence interharmonique
NOTE 1 Pour des raisons de concision, ce type de composante peut être désigné simplement par le terme « interharmonique ».
NOTE 2 Pour l’analyse pratique, il peut être nécessaire de procéder à une approximation de la périodicité.
NOTE 3 La valeur est normalement exprimée comme une valeur efficace.
NOTE 4 Comme indiqué dans la CEI 61000-4-7, la fenêtre temporelle a une largeur de 10 périodes fondamentales (systèmes de 50 Hz) ou de 12 périodes fondamentales (systèmes de 60 Hz), c’est-à-dire approximativement 200 ms. La différence de fréquence entre deux composantes interharmoniques consécutives est, par conséquent, d’environ 5 Hz. Dans le cas d’autres fréquences fondamentales, il convient de choisir la fenêtre temporelle entre 6 périodes fondamentales (environ 1 000 ms à 6 Hz) et 18 périodes fondamentales (environ 100 ms à 180 Hz). [IEC 60146-1-1, ed. 4.0 (2009-06)]
На частотах, расположенных между частотами гармонических составляющих тока и напряжения, могут наблюдаться интергармоники. Интергармоники могут возникать на дискретных частотах или иметь спектральные составляющие в достаточно широкой полосе частот. Суммарное воздействие различных источников интергармоник маловероятно и в настоящем стандарте не учитывается.
Полного понимания природы электромагнитных возмущений, ассоциирующихся с интергармониками, еще нет, и в настоящее время к этому явлению возник повышенный интерес. Интергармоники всегда присутствуют в системе электроснабжения, но в последнее время с резким увеличением силовых электронных систем их практическое влияние стало более ощутимым.
[Збигнев Ханзелка (Zbigniew Hanzelka), Анжей Бьень (Andrzej Bien) AGH-UST, Краков, Республика Польша. Энергосбережение №7/2005]Тематики
Действия
Синонимы
EN
FR
Русско-французский словарь нормативно-технической терминологии > интергармоника
-
5 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
-
6 переключающий контакт
переключающий контакт электрической цепи
Контакт электрической цепи, который размыкает одну электрическую цепь и замыкает другую при заданном действии устройства
[ ГОСТ 14312-79]
переключающий контакт
switching contact
Механический контакт, предназначенный для замыкания и размыкания электрической цепи.
[ ГОСТ Р МЭК 60050-426-2006]EN
change-over contact
combination of two contact circuits with three contact members, one of which is common to the two contact circuits; such that when one of these contact circuits is open, the other is closed
[IEV number 444-04-19]FR
contact à deux directions, m
contact inverseur (déconseillé), m
combinaison de deux circuits de contact comprenant trois éléments de contact, l'un d'eux étant commun aux deux circuits de contact ; de telle manière que lorsque l'un des circuits de contact est ouvert, l'autre est fermé
[IEV number 444-04-19]Параллельные тексты EN-RU CO contact
Compound contact consisting of a NO (make) contact and a NC (break) contact with a common terminal. On changing the switch position, the contact previously closed opens first followed by the closing of the contact that was previously open. Note: in case of a switching arc the NO and NC contact may be temporarily electrically connected.
[Tyco Electronics]Переключающий контакт
Контакт, объединяющий в себе замыкающий и размыкающий контакты с общим выводом. При изменении коммутационного положения сначала размыкается ранее замкнутый контакт, затем замыкается контакт, который до этого был разомкнут. Примечание. Если в процессе коммутации возникнет дуга между размыкающим и замыкающим контактами, то между ними может установиться кратковременная электрическая связь.
[Перевод Интент]Недопустимые, нерекомендуемые
Тематики
Обобщающие термины
Синонимы
EN
- C/O
- change-over contact
- changeover contact
- CO contact
- double-throw contact
- make-and-break contact
- switching contact
- transfer contact
- two-way contact
DE
FR
Русско-французский словарь нормативно-технической терминологии > переключающий контакт
-
7 промежуточный адаптер (для эдектроустановочных изделий)
промежуточный адаптер (для эдектроустановочных изделий)
-
[IEV number 442-03-21]EN
intermediate adaptor (for accessories)
adaptor which allows the connection of one or more types of plug to a socket-outlet via a control device such as a dimmer, clock switch, photo-electric switch, etc., which can be either integral with the intermediate adaptor or connected to it by a flexible cable, and in which case can be either rewireable or non-rewireable
[IEV number 442-03-21]FR
adaptateur intermédiaire (pour le petit appareillage)
adaptateur qui permet la connexion d'un ou de plusieurs types de fiches à un socle de prise de courant au moyen d'un dispositif de commande tel qu'un gradateur, un interrupteur horaire, un interrupteur photoélectrique, etc., qui peut être soit partie intégrante de l'adaptateur intermédiaire soit connecté à ce dernier au moyen d'un câble souple, et qui dans ce cas peut être démontable ou non
[IEV number 442-03-21]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > промежуточный адаптер (для эдектроустановочных изделий)
-
8 проходной изолятор
- traversée
- isolateur de traversée, m
проходной изолятор
Изолятор, предназначенный для провода токоведущих элементов через стенку, имеющую другой электрический потенциал.
[ ГОСТ 27744-88]
проходной изолятор
-
[IEV number 151-15-40]EN
(insulating) bushing
insulator forming a passage for a conductor through a non-insulating partition
[IEV number 151-15-40]
bushing
A bushing is a cyclindrical insulating component, usually made of ceramic, that houses a conductor. It enables a conductor to pass through a grounded enclosure, such as a transformer tank (the physical shell of a transformer), a wall or other physical barrier, to connect electrical installations. In the case of a transformer, bushings protect the conductors that connect a transformer’s core to the power system it serves through channels in the transformer’s housing.
[ABB. Glossary of technical terms. 2010]FR
isolateur de traversée, m
traversée, f
isolateur permettant le passage d'un conducteur à travers une paroi non isolante
[IEV number 151-15-40]
Проходной изоляторПараллельные тексты EN-RU
The circuit breaker is connected via bushings to the rest of the switchgear at the flanges provided.
[Siemens]С другими частями распределительного устройства силовой выключатель соединяется через проходные изоляторы, закрепленные в его фланцах.
[Перевод Интент]Тематики
Классификация
>>>Обобщающие термины
EN
DE
FR
- isolateur de traversée, m
- traversée
Русско-французский словарь нормативно-технической терминологии > проходной изолятор
-
9 пуск переключением со звезды на треугольник
пуск переключением со звезды на треугольник
-EN
star-delta starting
the process of starting a three-phase motor by connecting it to the supply with the primary winding initially connected in star, then reconnected in delta for the running condition
[IEV number 411-52-16]FR
démarrage étoile-triangle
mode de démarrage d'un moteur triphasé à tension réduite, consistant à relier à la source à tension constante les enroulements statoriques, d'abord en couplage étoile, puis à passer au couplage triangle pour le fonctionnement normal
[IEV number 411-52-16]Magnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Y/Δ changeover node - Узел переключения со звезды на треугольник
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Contactor KΔ - Контактор KΔ
Contactor KY- Контактор KY
Параллельные тексты EN-RU Star-delta Y/Δ starting
Star-delta starting is the best known system and perhaps the commonest starting system at reduced voltage; it is used to start the motor reducing the mechanical stresses and limiting the current values during starting; on the other hand, it makes available a reduced inrush torque.This system can be used for motors with terminal box with 6 terminals and double supply voltage.
It is particularly suitable for no-load starting or with low and constant load torque or lightly increasing load torque, such as in the case of fans or low power centrifugal pumps.
Making reference to the diagram of Figure 6, the starting modality foresees the initial phase with star-connection of the windings to be realized through the closing of the circuit-breaker, of the line contactor KL and of the star contactor KY.
After a suitable predetermined period of time, the opening of the contactor KY and the closing of KΔ allow switching to delta-connection, which is also the configuration of normal running position.
[ABB]Пуск переключением со звезды на треугольник
Пуск переключением со звезды на треугольник является самым известным способом и, возможно, самой распространенной схемой пуска на пониженном напряжении. С одной стороны, этот способ используется для снижения механических нагрузок и ограничения пускового тока, а с другой - обеспечивает уменьшение пускового момента.Такая возможность может быть реализована в двигателях с шестью зажимами в выводной коробке, что позволяет питать его от двух напряжений.
Особенно этот способ подходит для ненагруженного пуска и пуска с низким постоянным или немного увеличивающимся вращающим моментом, например, для пуска вентиляторов или маломощных центробежных насосов.
Схема пуска переключением со звезды на треугольник представлена на рисунке 6. В начальный момент пуска обмотки статора соединяют звездой путем замыкания контактов автоматического выключателя, линейного контактора KL и контактора KY со схемой "звезда".
По истечении заданного времени контакты контактора KY размыкаются и замыкаются контакты контактора КΔ со схемой треугольник.
В результате выполняется переключение обмоток статора со схемы «звезда» на схему «треугольник».
Обе схемы соединения обмоток являются схемами нормального рабочего режима.
[Перевод Интент]Тематики
Обобщающие термины
EN
- star-delta starting
- Y/Δ starting
DE
FR
Русско-французский словарь нормативно-технической терминологии > пуск переключением со звезды на треугольник
-
10 температура окружающей среды
- température ambiante, f
температура окружающей среды
Средняя температура воздуха или другой среды около оборудования.
Примечание - В процессе измерения температуры окружающей среды измерительный прибор (зонд) должен быть экранирован от сквозняков и нагрева излучением.
[ ГОСТ Р МЭК 60050-826-2009]
температура окружающей среды
Температура воздуха или другой среды в непосредственной близости от оборудования или компонента.
[ ГОСТ Р МЭК 60050-426-2006]
температура окружающей среды
Предполагают, что под температурой окружающей среды понимают воздействующие факторы со стороны всего другого оборудования, установленного в том же помещении.
Температура окружающей среды, которую следует учитывать применительно к оборудованию, - это температура в том месте, где оно должно быть установлено, с учетом влияния другого оборудования и источников тепла в том же месте в процессе работы без учета тепла от устанавливаемого оборудования
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
температура окружающей среды
Температура воздуха или среды в том месте, где должно быть использовано оборудование.
[ ГОСТ Р МЭК 60204-1-2007]EN
ambient temperature
average temperature of air or another medium in the vicinity of the equipment
NOTE – During the measurement of the ambient temperature the measuring instrument/probe should be shielded from draughts and radiant heating.
[IEV number 826-10-03]
ambient temperature
temperature of the air or other medium where the equipment is to be used
[IEC 60204-1-2006]FR
température ambiante, f
température moyenne de l'air ou du milieu au voisinage du matériel
NOTE – Pendant la mesure de la température ambiante il est recommandé que l'instrument/la sonde de mesure soit protégée des courants d'air et de la chaleur rayonnée.
[IEV number 826-10-03]Параллельные тексты EN-RU
The temperate of each module of a Molded Case Circuit Breaker is the sum of temperature increase by conduction and ambient temperature and if the ambient temperature exceeds 40°C the passing current needs to be reduced so that the temperature of such element as internal insulator of MCCB exceed the maximum allowable temperature.
[LS Industrial Systems]Температура частей автоматического выключателя в литом корпусе равна температуре окружающей среды плюс температура, определяемая количеством теплоты, выделяемой при протекании электрического тока. Если автоматический выключатель эксплуатируется при температуре окружающей среды, превышающей 40 °C, то следует учитывать, что номинальный ток такого выключателя будет немного меньше. Учет этого обстоятельства позволит избежать недопустимого нагрева частей автоматического выключателя, выполненных из изоляционного материала.
[Перевод Интент]Тематики
EN
DE
- Umgebungstemperatur, f
FR
- température ambiante, f
Русско-французский словарь нормативно-технической терминологии > температура окружающей среды
См. также в других словарях:
Case modding — Case modification (commonly referred to as case modding where an individual project is referred to as a case mod) is the modification of a computer chassis (often just referred to as the case), or a video game console chassis. Modifying a… … Wikipedia
Case-control — is a type of epidemiological study design. Case control studies are used to identify factors that may contribute to a medical condition by comparing subjects who have that condition (the cases ) with patients who do not have the condition but are … Wikipedia
Case (goods) — A case of some merchandise is a collection of items packaged together. In the United States, typically a standard case contains a certain number of items depending on what the merchandise is. For consumer foodstuffs such as canned goods, soda,… … Wikipedia
Case of first impression — A case of first impression (known as primae impressionis in Latin) is a legal case in which there is no binding authority on the matter presented. A case of first impression may be a case of first impression in only a particular jurisdiction. In… … Wikipedia
case reserved — A statement in writing of the facts proved on the trial of a cause, drawn up and settled by the attorneys and counsel for the respective parties under the supervision of the judge, for the purpose of having certain points of law, which arose at… … Black's law dictionary
case reserved — A statement in writing of the facts proved on the trial of a cause, drawn up and settled by the attorneys and counsel for the respective parties under the supervision of the judge, for the purpose of having certain points of law, which arose at… … Black's law dictionary
Case hardening — or surface hardening is the process of hardening the surface of a metal, often a low carbon steel, by infusing elements into the material s surface, forming a thin layer of a harder alloy. Case hardening is usually done after the part in question … Wikipedia
Case Western Reserve University — Motto Thinking Beyond the Possible Established WRU: 1826 CIT: 1880 CWRU: 1967 Type … Wikipedia
Case grammar — is a system of linguistic analysis, focusing on the link between the valence of a verb and the grammatical context it requires, created by the American linguist Charles J. Fillmore in (1968), in the context of Transformational Grammar. This… … Wikipedia
Case-based reasoning — (CBR), broadly construed, is the process of solving new problems based on the solutions of similar past problems. An auto mechanic who fixes an engine by recalling another car that exhibited similar symptoms is using case based reasoning. A… … Wikipedia
case — case1 [kās] n. [ME & OFr cas, an event < L casus, a chance, lit., falling, pp. of cadere, to fall < IE base * k̑ad , to fall > Sans s̍ad , to fall off] 1. an example, instance, or occurrence [a case of carelessness, a case of measles] 2 … English World dictionary