-
21 LV switchgear and controlgear assembly
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
Англо-русский словарь нормативно-технической терминологии > LV switchgear and controlgear assembly
-
22 LV switchgear assembly
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
Англо-русский словарь нормативно-технической терминологии > LV switchgear assembly
-
23 power switchgear and controlgear assembly
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
силовое комплектное устройство распределения и управления
СНКУ
Низковольтное комплектное устройство распределения и управления, применяемое для распределения и управления энергией всех типов нагрузок промышленного, коммерческого и аналогичного назначений, не предназначенное для управления не квалифицированным персоналом.
[ ГОСТ Р МЭК 61439.2-2012]EN
power switchgear and controlgear assembly
PSC-assembly
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
NOTE It is not excluded for a PSC-assembly to be located in an area accessible to ordinary persons.
[IEC 61439-2, ed. 2.0 (2011-08)]FR
ensemble d'appareillage de puissance
ensemble EAP
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
NOTE Il n’est pas exclu d’implanter un ensemble EAP dans une zone accessible aux personnes ordinaires.
[IEC 61439-2, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
FR
Англо-русский словарь нормативно-технической терминологии > power switchgear and controlgear assembly
-
24 PSC-assembly
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
силовое комплектное устройство распределения и управления
СНКУ
Низковольтное комплектное устройство распределения и управления, применяемое для распределения и управления энергией всех типов нагрузок промышленного, коммерческого и аналогичного назначений, не предназначенное для управления не квалифицированным персоналом.
[ ГОСТ Р МЭК 61439.2-2012]EN
power switchgear and controlgear assembly
PSC-assembly
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
NOTE It is not excluded for a PSC-assembly to be located in an area accessible to ordinary persons.
[IEC 61439-2, ed. 2.0 (2011-08)]FR
ensemble d'appareillage de puissance
ensemble EAP
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
NOTE Il n’est pas exclu d’implanter un ensemble EAP dans une zone accessible aux personnes ordinaires.
[IEC 61439-2, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
FR
Англо-русский словарь нормативно-технической терминологии > PSC-assembly
-
25 switchgear/controlgear
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
Англо-русский словарь нормативно-технической терминологии > switchgear/controlgear
-
26 drive
1) привод; передача2) привод; приведение в действие || приводить в действие || приводной3) узел привода; приводной блок4) ведущий5) забивать; вколачивать; вбивать•to face drive — вести за торец, поворачивать за торец ( обрабатываемую деталь)
drive with electronic variable speeds — привод с электронным регулированием скорости или частоты вращения
- ac drive- adjustable speed drive
- air-bearing capstan drive
- allhydraulic drive
- alternating current drive
- angle drive
- angular belt drive
- arc-type stator drive
- automatic electric drive
- automatic electrical drive
- auxiliary drive
- axial drive
- axis drive
- balanced drive
- ball screw drive
- belt drive
- belt-and-pulley drive
- bevel gear drive
- bidirectional drive
- blade drive
- brushless drive
- cable drive
- cam drive
- camshaft drive
- capstan drive
- carriage rapid traverse drive
- C-axis drive
- center drive
- central accessory drive
- chain drive
- chain-and-sprocket drive
- close fluid drive
- closed fluid power drive
- closed-loop servo drive
- clutch-controlled drive
- common drive
- common hard drive
- cone-friction drive
- cone-pulley drive
- configurable computer-controlled drive
- configurable drive
- conservative controlled electric drive
- conservative controlled electrical drive
- constant speed drive
- continuous drive
- continuous rotation electric drive
- continuous rotation electrical drive
- continuously rated drive
- continuously variable ratio drive
- contrarotating concentric shaft drive
- control drive
- controlled electric drive
- convertible drive
- coordinate drive
- cord drive
- countershaft drive
- crank drive
- crossed belt drive
- cutting stroke drive
- cycloidal drive
- dc drive
- dependent drive
- differential drive
- digital drive
- direct belt drive
- direct current drive
- direct drive
- disengageable drive
- disk drive
- displacing drive
- dissipative controlled electric drive
- double-enveloping wormgear drive
- double-reduction drive
- drive of a machine
- drive of the machine retaining device
- dual drive
- dual floppy disk drive
- dual motor drive
- dual speed drive
- eccentric drive
- eccentrical drive
- electric arc drive
- electric drive with cascade
- electric drive with contactless control
- electric drive with converter
- electric drive with coupling
- electric drive with magnetic slip coupling
- electric drive with magnetic solid coupling
- electric drive with relay-contactor control
- electric drive with rotary amplifier control
- electric drive with servomotor control
- electric drive with transductor
- electric drive with valve cascade converter
- electric drive without speed control
- electric drive
- electrical drive
- electric-powered drive
- electromagnetic drive
- electromagnetically braked drive
- electromechanical drive
- electronic drive
- electronic motor drive
- electronically controlled drive
- enclosed drive
- endless drive
- epycyclic gear drive
- exposed drive
- feed and upsetting drive
- feed drive
- final controlling drive
- final drive
- fine displacing drive
- fixed fluid drive
- fixed fluid power drive
- flat-belt drive
- floppy disk drive
- floppy drive
- fluid drive
- fluid power drive
- flywheel drive
- friction drive
- friction roller drive
- full controlled electric drive
- full hydraulic drive
- gear drive
- gear ratioed drive
- gearless electric drive
- gear-motor drive
- GEC DC axis drive
- general drive
- Geneva drive
- globoidal index cam drive
- globoidal indexing cam drive
- group electric drive
- hand drive
- hard drive
- hard-disk drive
- harmonic drive
- head and tail drive
- helical gear drive
- high-speed drive
- hugger drive
- hydraulic drive
- hydraulic power drive
- hydraulic pressure drive
- hydrodynamic drive
- hydrodynamic power drive
- hydroelectric drive
- hydrostatic drive
- hydrostatic power drive
- incremental drive
- independent drive
- index drive
- indexing drive
- individual electric drive
- infinitely variable drive
- integral ballscrew drive
- intermediate accessory drive
- intermittent drive
- key drive
- laptop hard drive
- limited rotary fluid drive
- limited rotary fluid power drive
- linear fluid drive
- linear fluid power drive
- linear motor slide drive
- link drive
- link motion drive
- liquid drive
- low-inertia drive
- low-speed drive
- machine axis drive
- magnetic drive
- magnetohydrodynamic drive
- magneto-optical disk drive
- main motion drive
- main spindle drive
- manual drive
- mechanical drive
- mechanical-hydraulic drive
- medium speed drive
- minidiskette drive
- motor drive
- multidirectional drive
- multimotor drive
- multiple-reduction drive
- multiple-reduction-gear drive
- multiple-thread roller drive
- multispeed electric drive
- nonautomatic electric drive
- noncomplete controlled electric drive
- nongeared drive
- nonslip drive
- oil-hydraulic drive
- open belt drive
- open fluid drive
- open fluid power drive
- optical disk drive
- optifeed drive
- oscillating crank drive
- over drive
- paper drive
- pen drive
- pinion-rack drive
- planetary drive
- planetary gear drive
- pneumatic drive
- pneumatic power drive
- posifeed drive
- positive drive
- power drive
- power tool drive
- powered drive
- primary drive
- PWM drive
- quarter-turn belt drive
- quarter-turn drive
- quarter-twist belt drive
- quarter-twist drive
- rack-and-pinion drive
- rack-and-pinion friction drive
- ram drive
- rapid return drive
- rapid traverse drive
- ratchet drive
- R-axis drive
- reciprocating electric drive
- rectifier-controlled drive
- reduction drive
- reduction electric drive
- remote drive
- return-stroke drive
- reversing drive
- right-angle drive
- roller drive
- roller-chain drive
- rolling ring drive
- rolling screw motion drive
- rope drive
- rotary fluid drive
- rotary fluid power drive
- rotary tool drive
- rotary-to-rotary drive
- rotation electric drive
- rugged drive
- SCR drive
- screw drive
- self-propelled drive
- separate drive
- servo drive
- servo-controlled drive
- servoed drive
- severe duty drive
- shiftable drive
- short center drive
- silent chain drive
- silicon controlled rectifier drive
- single drive
- single-enveloping wormgear drive
- single-gear drive
- single-motorized drive
- single-pulley drive
- single-reduce drive
- single-reduction drive
- skew angle drive
- slave drive
- slip-free drive
- slot-and-crank drive
- slot-type drive
- socket wrench drive
- speed-decreasing drive
- speed-increasing drive
- speed-reducing drive
- spindle drive
- spiral drive
- spiral gear drive
- spring drive
- spur gear drive
- spur wheel drive
- stabilized fluid drive
- stabilized fluid power drive
- steel belt drive
- step electric drive
- step motor drive
- steplessly variable drive
- steplessly variable speed drive
- stepped pulley drive
- stepper motor drive
- stepping motor drive
- step-type drive
- straight drive
- stroke electric drive
- stylus drive
- subsidiary drive
- synchronous belt drive
- synchronous drive
- tandem drive
- tape drive
- tenon drive
- texrope drive
- three-range drive
- thyristor drive
- thyristor-controlled drive
- to drive off
- to drive out
- tooth-belt drive
- toothed drive
- toothed-belt drive
- tooth-gear drive
- traction drive
- transfer drive
- transmission drive
- treadle drive
- twin chain drive
- twin drive
- twin gear drive
- twist-roller friction drive
- two-lobe harmonic drive
- two-winding spindle drive
- underslung drive
- unit drive
- valve electric drive
- variable fluid drive
- variable fluid power drive
- variable frequency drive
- variable-speed drive
- variable-speed tape drive
- variable-speed work drive
- V-belt drive
- vee-belt drive
- vee-belt-motor drive
- vibratory drive
- vibratory electric drive
- Ward-Leonard drive
- workhead drive
- worm drive
- worm-and-rack drive
- wormgear drive
- X-axis drive
- Y-axis drive
- Z-axis driveEnglish-Russian dictionary of mechanical engineering and automation > drive
-
27 PES
1) Общая лексика: process equipment supplier2) Медицина: СПП, стент, покрытый паклитакселом3) Военный термин: PULHEEMS employment standard, Positive Enable System, permanent executive secretariat, pointing error sensor, program evaluation system4) Техника: passive electromagnetic system, polyethersulphone5) Химия: Polyethersulfone6) Грубое выражение: Pissy Ending Syndrome7) Оптика: photoelectric scanner8) Сокращение: Performance Evaluation System, Private Express Statutes (together with "Universal Service Obligation" and "Exclusive Mailbox Access" rule = USPS postal monopoly), post enumeration survey, processed eucheuma seaweed, переработанная морская водоросль эухеума9) Текстиль: полиэстр10) Физика: photoelectron spectroscopy11) Физиология: Psychiatric Evaluation Service12) Электроника: Photo- Electron Spectroscopy, Programmer Electronic Switch13) Вычислительная техника: Programmed Electrical Stimulation, packetised elementary stream, система оценки программы, P-bit Errored Seconds (DS3/E3, BIT), Photo-Electric Scanning (DTP), Proposed Encryption Standard (Verschluesselung)14) Стоматология: pink esthetic score15) Связь: personal earth station16) Фирменный знак: Percy Engineering Services, Petroleum Engineering Services17) Сетевые технологии: Packetized Elementary Stream, Process Engineering Suite18) Сахалин А: programmable electronic system19) Медицинская техника: Programmed Extra Stimulation (режим работы устройства кардиостимуляции)20) Безопасность: Proposed Encryption Standard21) Расширение файла: Positioning Error Signal, Processor Enhancement Socket, Processor Upgrade Socket, Program Editor work space file (WordPerfect Library)22) Энергосистемы: Public Electricity Supplier23) Нефть и газ: potential earthquake source, ВОЗ, возможный очаг сильных землетрясений25) Аэропорты: Petrozavodsk, Russia26) Программное обеспечение: Personal Email Solution -
28 pes
1) Общая лексика: process equipment supplier2) Медицина: СПП, стент, покрытый паклитакселом3) Военный термин: PULHEEMS employment standard, Positive Enable System, permanent executive secretariat, pointing error sensor, program evaluation system4) Техника: passive electromagnetic system, polyethersulphone5) Химия: Polyethersulfone6) Грубое выражение: Pissy Ending Syndrome7) Оптика: photoelectric scanner8) Сокращение: Performance Evaluation System, Private Express Statutes (together with "Universal Service Obligation" and "Exclusive Mailbox Access" rule = USPS postal monopoly), post enumeration survey, processed eucheuma seaweed, переработанная морская водоросль эухеума9) Текстиль: полиэстр10) Физика: photoelectron spectroscopy11) Физиология: Psychiatric Evaluation Service12) Электроника: Photo- Electron Spectroscopy, Programmer Electronic Switch13) Вычислительная техника: Programmed Electrical Stimulation, packetised elementary stream, система оценки программы, P-bit Errored Seconds (DS3/E3, BIT), Photo-Electric Scanning (DTP), Proposed Encryption Standard (Verschluesselung)14) Стоматология: pink esthetic score15) Связь: personal earth station16) Фирменный знак: Percy Engineering Services, Petroleum Engineering Services17) Сетевые технологии: Packetized Elementary Stream, Process Engineering Suite18) Сахалин А: programmable electronic system19) Медицинская техника: Programmed Extra Stimulation (режим работы устройства кардиостимуляции)20) Безопасность: Proposed Encryption Standard21) Расширение файла: Positioning Error Signal, Processor Enhancement Socket, Processor Upgrade Socket, Program Editor work space file (WordPerfect Library)22) Энергосистемы: Public Electricity Supplier23) Нефть и газ: potential earthquake source, ВОЗ, возможный очаг сильных землетрясений25) Аэропорты: Petrozavodsk, Russia26) Программное обеспечение: Personal Email Solution -
29 plug
- штекер
- сменный центральный выступ бескернового наконечника
- самозаклинивание керна (в коронке, расширителе, колонковой трубе)
- пуансон пресс-формы
- пробочный предохранитель
- пробка-вертлюг
- пробка (в упаковке)
- поставить пробку (в скважине)
- плунжер насоса
- перекрывать приток воды или нефти в скважину
- оправка
- затампонировать скважину
- засыпать ликвидированную скважину песком
- залить скважину цементом
- закупорить трещины и пустоты в стенках скважины
- закупоривать
- вилка кабельная
- вилка
- армированный алмазами вкладыш к коронке
армированный алмазами вкладыш к коронке
(для бурения сплошным забоем)
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
вилка
Часть соединителя, имеющая штыри для осуществления контакта с розеткой и средства для электрического соединения и закрепления гибкого кабеля
[ ГОСТ Р 51322.1-99]
вилка
Часть соединителя, которая выполняется как одно целое или непосредственно прикрепляется к гибкому кабелю, подсоединяемому к аппарату или переносной розетке.
[ ГОСТ Р 51323.1-99]
вилка (кабельная вилка)
Часть соединителя, которая выполняется как одно целое и прикрепляется к гибкому кабелю, подсоединяемому к электроприбору или переносной розетке.
Примечание — Вилка кабельного соединителя аналогична вилке штепсельного соединителя
[ ГОСТ Р 51323.1-99]
вилка
-
[IEV number 442-03-01]EN
plug
the part integral with or intended to be attached directly to one flexible cable connected to the equipment or to a connector
[IEC 60309-1, ed. 4.0 (1999-02)]
plug
the part integral with or intended to be attached to one flexible cable connected to the equipment or to a connector
NOTE The plug of a cable coupler is identical to the plug of a "plug and socket-outlet".
[IEC 60309-1, ed. 4.0 (1999-02)]
plug
accessory having pins designed to engage with the contacts of a socket-outlet, also incorporating means for the electrical connection and mechanical retention of flexible cables or cords
[IEV number 442-03-01]FR
fiche
partie faisant corps avec le câble souple raccordé au matériel ou à une prise mobile ou destinée à être reliée directement à un tel câble
[IEC 60309-1, ed. 4.0 (1999-02)]
fiche
partie faisant corps avec le câble souple raccordé au matériel ou à une prise mobile ou destinée à être reliée à un tel câble
NOTE La fiche d'un prolongateur est identique à la fiche d'une prise de courant.
[IEC 60309-1, ed. 4.0 (1999-02)]
fiche
appareil pourvu de broches conçues pour s'engager dans les contacts d'un socle de prise de courant et comprenant également des pièces pour la connexion électrique et la retenue mécanique des câbles souples
[IEV number 442-03-01]

Вилка (опрессованная) бытового назначения
(Кабельная) вилка (разборная) промышленного назначения
Рис. ABB
1 - Розетка стационарная
2 - Вилка опрессованная
3 - Удлиннитель одноместный
4 - Соединитель штепсельный
5 - Розетка переносная опрессованная
6 - Вилка опрессованная
7 - Соединитель штепсельный
8 - Розетка приборная
9 - Удлинитель с приборной розеткой
10 - Вилка приборная
11 - Прибор
12 - Соединитель приборный
[ ГОСТ Р 51322.1-99]Форма и длина вилки должны обеспечивать ее свободное отключение рукой от соответствующей розетки.
[ ГОСТ 28244-96]
6.6.25. Вилки штепсельных соединителей должны быть выполнены таким образом, чтобы их нельзя было включать в розетки сети с более высоким номинальным напряжением, чем номинальное напряжение вилки. Конструкция розеток и вилок не должна допускать включения в розетку только одного полюса двухполюсной вилки, а также одного или двух полюсов трехполюсной вилки.
[ПУЭ]
Для осуществления соединения при помощи розетки и вилки к розетке должен подключаться источник энергии, а к вилке - ее приемник.
[ ГОСТ 12.2.007.0-75]
Тематики
Действия
EN
DE
FR
Рис. ABB
Рис. Schneider Electric
Тематики
EN
FR
закупорить трещины и пустоты в стенках скважины
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
залить скважину цементом
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
засыпать ликвидированную скважину песком
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
затампонировать скважину
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
оправка
1. Стержень или шпиндель, на который одевают трубу при испытании на раздачу.
2. Стержень, который вставляется в трубу при волочении через фильеру.
3. Кернер или шпиндель, с помощью которого выдавливается чашка.
4. Блок, выступающий в ручье штампа для формирования соответствующей впадины в поковке.
5. Фальшдно в штампе.
[ http://www.manual-steel.ru/eng-a.html]Тематики
EN
перекрывать приток воды или нефти в скважину
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
поставить пробку (в скважине)
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
пробка
Укупорочное средство, вставляемое внутрь горловины тары.
[ ГОСТ 17527-2003]Тематики
- упаковка, упаковывание
Обобщающие термины
EN
DE
FR
пробка-вертлюг
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
пробочный предохранитель
пробка
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
Синонимы
EN
пуансон пресс-формы
Ндп. вкладыш
вставка
знак
стаканчик
шашка
Формообразующая деталь пресс-формы для оформления поверхности верхней части изделия.
[ ГОСТ 23165-78]Недопустимые, нерекомендуемые
Тематики
- пресс-формы для резинотехн. изделий
Обобщающие термины
EN
DE
FR
самозаклинивание керна (в коронке, расширителе, колонковой трубе)
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
EN
сменный центральный выступ бескернового наконечника
«пилот»
—
[ http://slovarionline.ru/anglo_russkiy_slovar_neftegazovoy_promyishlennosti/]Тематики
Синонимы
- «пилот»
EN
штекер
штыревой разъем
Окончание соединительных кабелей, обеспечивающее электрическое соединение контактом проводников, механическое совмещение с гнездовым разъемом и фиксацию защелкой (ISO/IEC 11801).
[ http://www.iks-media.ru/glossary/index.html?glossid=2400324]Тематики
- электросвязь, основные понятия
Синонимы
EN
3.1 вилка (plug): Часть соединителя, имеющая штыри для осуществления контакта с розеткой и средство для электрического соединения и закрепления гибкого кабеля.
Источник: ГОСТ Р 51322.1-2011: Соединители электрические штепсельные бытового и аналогичного назначения. Часть 1. Общие требования и методы испытаний оригинал документа
Англо-русский словарь нормативно-технической терминологии > plug
-
30 connector pins
электрический соединитель
Электротехническое устройство, предназначенное для механического соединения и разьединения электрических цепей, состоящее из двух или более частей (вилки, розетки), образующих разъемное контактное соединение
[ ГОСТ 21962-76]
электрический соединитель
Электромеханическое устройство, присоединяемое к проводникам, для соединения и разъединения электрических цепей путем сочленения и расчленения с соответствующим устройством.
[ ГОСТ 23784-98]
электрический соединитель
Электромеханическое устройство, предназначенное для механического соединения и разъединения вручную электрических цепей (проводов, кабелей, модулей, узлов и блоков) в различных видах аппаратуры при выключенном источнике тока через соединитель.
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]
разъем
Конструктивный элемент, состоящий из соединяемых частей, служащий для электрического соединения кабеля с электронным блоком, преобразователем или электронных блоков между собой.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
разъем
Комбинация вилки и розетки, обеспечивающая соединение и разъединение двух или более проводников.
Примечание.
Примерами разъемов могут служить комбинации:
- соединителей, которые соответствуют требованиям МЭК 61984;
- приборные соединители, кабельные гнезда и бытовые соединители в соответствии с МЭК 60309-1;
- приборные соединители в соответствии с МЭК 60884-1 или бытовые соединители в соответствии с МЭК 60320-1.
[ ГОСТ Р МЭК 60204-1-2007]
разъем
-
[IEV number 151-12-19]EN
connector
device providing connection and disconnection to a suitable mating component
NOTE – A connector has one or more contact elements.
Source: 151-12-19 MOD
[IEV number 581-26-01]FR
connecteur, m
dispositif destiné à établir et à rompre une connexion par appariement avec un composant complémentaire approprié
NOTE – Un connecteur est muni d’un ou plusiers éléments de contact
Source: 151-12-19 MOD
[IEV number 581-26-01]Конструкция соединителей, предназначенных для подключения внешних цепей, должна отличаться от конструкции других соединителей и не должна быть взаимозаменяемой.
Конструкция соединителя должна исключать возможность неправильного сочленения, например, с помощью направляющих штифтов или гнезд.
Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Близкие понятия
Действия
Синонимы
EN
- connector
- connector pins
- connector set
- electric connector
- electric coupler
- electrical connector mated set
- electrical coupler
- plug-and-socket connector
- withdraw connector
DE
- Steckverbinder, m
FR
- connecteur, m
Смотри также
Англо-русский словарь нормативно-технической терминологии > connector pins
31 connector set
электрический соединитель
Электротехническое устройство, предназначенное для механического соединения и разьединения электрических цепей, состоящее из двух или более частей (вилки, розетки), образующих разъемное контактное соединение
[ ГОСТ 21962-76]
электрический соединитель
Электромеханическое устройство, присоединяемое к проводникам, для соединения и разъединения электрических цепей путем сочленения и расчленения с соответствующим устройством.
[ ГОСТ 23784-98]
электрический соединитель
Электромеханическое устройство, предназначенное для механического соединения и разъединения вручную электрических цепей (проводов, кабелей, модулей, узлов и блоков) в различных видах аппаратуры при выключенном источнике тока через соединитель.
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]
разъем
Конструктивный элемент, состоящий из соединяемых частей, служащий для электрического соединения кабеля с электронным блоком, преобразователем или электронных блоков между собой.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
разъем
Комбинация вилки и розетки, обеспечивающая соединение и разъединение двух или более проводников.
Примечание.
Примерами разъемов могут служить комбинации:
- соединителей, которые соответствуют требованиям МЭК 61984;
- приборные соединители, кабельные гнезда и бытовые соединители в соответствии с МЭК 60309-1;
- приборные соединители в соответствии с МЭК 60884-1 или бытовые соединители в соответствии с МЭК 60320-1.
[ ГОСТ Р МЭК 60204-1-2007]
разъем
-
[IEV number 151-12-19]EN
connector
device providing connection and disconnection to a suitable mating component
NOTE – A connector has one or more contact elements.
Source: 151-12-19 MOD
[IEV number 581-26-01]FR
connecteur, m
dispositif destiné à établir et à rompre une connexion par appariement avec un composant complémentaire approprié
NOTE – Un connecteur est muni d’un ou plusiers éléments de contact
Source: 151-12-19 MOD
[IEV number 581-26-01]Конструкция соединителей, предназначенных для подключения внешних цепей, должна отличаться от конструкции других соединителей и не должна быть взаимозаменяемой.
Конструкция соединителя должна исключать возможность неправильного сочленения, например, с помощью направляющих штифтов или гнезд.
Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Близкие понятия
Действия
Синонимы
EN
- connector
- connector pins
- connector set
- electric connector
- electric coupler
- electrical connector mated set
- electrical coupler
- plug-and-socket connector
- withdraw connector
DE
- Steckverbinder, m
FR
- connecteur, m
Смотри также
Англо-русский словарь нормативно-технической терминологии > connector set
32 electric connector
электрический соединитель
Электротехническое устройство, предназначенное для механического соединения и разьединения электрических цепей, состоящее из двух или более частей (вилки, розетки), образующих разъемное контактное соединение
[ ГОСТ 21962-76]
электрический соединитель
Электромеханическое устройство, присоединяемое к проводникам, для соединения и разъединения электрических цепей путем сочленения и расчленения с соответствующим устройством.
[ ГОСТ 23784-98]
электрический соединитель
Электромеханическое устройство, предназначенное для механического соединения и разъединения вручную электрических цепей (проводов, кабелей, модулей, узлов и блоков) в различных видах аппаратуры при выключенном источнике тока через соединитель.
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]
разъем
Конструктивный элемент, состоящий из соединяемых частей, служащий для электрического соединения кабеля с электронным блоком, преобразователем или электронных блоков между собой.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
разъем
Комбинация вилки и розетки, обеспечивающая соединение и разъединение двух или более проводников.
Примечание.
Примерами разъемов могут служить комбинации:
- соединителей, которые соответствуют требованиям МЭК 61984;
- приборные соединители, кабельные гнезда и бытовые соединители в соответствии с МЭК 60309-1;
- приборные соединители в соответствии с МЭК 60884-1 или бытовые соединители в соответствии с МЭК 60320-1.
[ ГОСТ Р МЭК 60204-1-2007]
разъем
-
[IEV number 151-12-19]EN
connector
device providing connection and disconnection to a suitable mating component
NOTE – A connector has one or more contact elements.
Source: 151-12-19 MOD
[IEV number 581-26-01]FR
connecteur, m
dispositif destiné à établir et à rompre une connexion par appariement avec un composant complémentaire approprié
NOTE – Un connecteur est muni d’un ou plusiers éléments de contact
Source: 151-12-19 MOD
[IEV number 581-26-01]Конструкция соединителей, предназначенных для подключения внешних цепей, должна отличаться от конструкции других соединителей и не должна быть взаимозаменяемой.
Конструкция соединителя должна исключать возможность неправильного сочленения, например, с помощью направляющих штифтов или гнезд.
Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Близкие понятия
Действия
Синонимы
EN
- connector
- connector pins
- connector set
- electric connector
- electric coupler
- electrical connector mated set
- electrical coupler
- plug-and-socket connector
- withdraw connector
DE
- Steckverbinder, m
FR
- connecteur, m
Смотри также
Англо-русский словарь нормативно-технической терминологии > electric connector
33 electric coupler
электрический соединитель
Электротехническое устройство, предназначенное для механического соединения и разьединения электрических цепей, состоящее из двух или более частей (вилки, розетки), образующих разъемное контактное соединение
[ ГОСТ 21962-76]
электрический соединитель
Электромеханическое устройство, присоединяемое к проводникам, для соединения и разъединения электрических цепей путем сочленения и расчленения с соответствующим устройством.
[ ГОСТ 23784-98]
электрический соединитель
Электромеханическое устройство, предназначенное для механического соединения и разъединения вручную электрических цепей (проводов, кабелей, модулей, узлов и блоков) в различных видах аппаратуры при выключенном источнике тока через соединитель.
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]
разъем
Конструктивный элемент, состоящий из соединяемых частей, служащий для электрического соединения кабеля с электронным блоком, преобразователем или электронных блоков между собой.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
разъем
Комбинация вилки и розетки, обеспечивающая соединение и разъединение двух или более проводников.
Примечание.
Примерами разъемов могут служить комбинации:
- соединителей, которые соответствуют требованиям МЭК 61984;
- приборные соединители, кабельные гнезда и бытовые соединители в соответствии с МЭК 60309-1;
- приборные соединители в соответствии с МЭК 60884-1 или бытовые соединители в соответствии с МЭК 60320-1.
[ ГОСТ Р МЭК 60204-1-2007]
разъем
-
[IEV number 151-12-19]EN
connector
device providing connection and disconnection to a suitable mating component
NOTE – A connector has one or more contact elements.
Source: 151-12-19 MOD
[IEV number 581-26-01]FR
connecteur, m
dispositif destiné à établir et à rompre une connexion par appariement avec un composant complémentaire approprié
NOTE – Un connecteur est muni d’un ou plusiers éléments de contact
Source: 151-12-19 MOD
[IEV number 581-26-01]Конструкция соединителей, предназначенных для подключения внешних цепей, должна отличаться от конструкции других соединителей и не должна быть взаимозаменяемой.
Конструкция соединителя должна исключать возможность неправильного сочленения, например, с помощью направляющих штифтов или гнезд.
Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Близкие понятия
Действия
Синонимы
EN
- connector
- connector pins
- connector set
- electric connector
- electric coupler
- electrical connector mated set
- electrical coupler
- plug-and-socket connector
- withdraw connector
DE
- Steckverbinder, m
FR
- connecteur, m
Смотри также
электрический элемент связи
электрический соединитель
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]Тематики
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > electric coupler
34 withdraw connector
электрический соединитель
Электротехническое устройство, предназначенное для механического соединения и разьединения электрических цепей, состоящее из двух или более частей (вилки, розетки), образующих разъемное контактное соединение
[ ГОСТ 21962-76]
электрический соединитель
Электромеханическое устройство, присоединяемое к проводникам, для соединения и разъединения электрических цепей путем сочленения и расчленения с соответствующим устройством.
[ ГОСТ 23784-98]
электрический соединитель
Электромеханическое устройство, предназначенное для механического соединения и разъединения вручную электрических цепей (проводов, кабелей, модулей, узлов и блоков) в различных видах аппаратуры при выключенном источнике тока через соединитель.
[В. Ф. Лярский, О. Б. Мурадян. Электрические соединители. Справочник. Радио и связь, 1988]
разъем
Конструктивный элемент, состоящий из соединяемых частей, служащий для электрического соединения кабеля с электронным блоком, преобразователем или электронных блоков между собой.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
разъем
Комбинация вилки и розетки, обеспечивающая соединение и разъединение двух или более проводников.
Примечание.
Примерами разъемов могут служить комбинации:
- соединителей, которые соответствуют требованиям МЭК 61984;
- приборные соединители, кабельные гнезда и бытовые соединители в соответствии с МЭК 60309-1;
- приборные соединители в соответствии с МЭК 60884-1 или бытовые соединители в соответствии с МЭК 60320-1.
[ ГОСТ Р МЭК 60204-1-2007]
разъем
-
[IEV number 151-12-19]EN
connector
device providing connection and disconnection to a suitable mating component
NOTE – A connector has one or more contact elements.
Source: 151-12-19 MOD
[IEV number 581-26-01]FR
connecteur, m
dispositif destiné à établir et à rompre une connexion par appariement avec un composant complémentaire approprié
NOTE – Un connecteur est muni d’un ou plusiers éléments de contact
Source: 151-12-19 MOD
[IEV number 581-26-01]Конструкция соединителей, предназначенных для подключения внешних цепей, должна отличаться от конструкции других соединителей и не должна быть взаимозаменяемой.
Конструкция соединителя должна исключать возможность неправильного сочленения, например, с помощью направляющих штифтов или гнезд.
Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Близкие понятия
Действия
Синонимы
EN
- connector
- connector pins
- connector set
- electric connector
- electric coupler
- electrical connector mated set
- electrical coupler
- plug-and-socket connector
- withdraw connector
DE
- Steckverbinder, m
FR
- connecteur, m
Смотри также
Англо-русский словарь нормативно-технической терминологии > withdraw connector
35 connection
1. соединение; включение; сообщение; связь2. сочленение; наращивание инструмента3. соединительная деталь; соединительная муфта4. геол. привязка; увязка5. патрубок, штуцерbias cut hydrocouple connection — муфтовое соединение с косыми фланцами (для ремонта подводных трубопроводов)
* * *
1. соединение; соединительная деталь2. соединительный патрубок; штуцерbias cut hydrocouple connection — муфтовое соединение с косыми фланцами (для ремонта подводных трубопроводов)
* * *
соединение, связь, наращивание бурового инструмента
* * *
1) соединение2) соединительная муфта; соединительная деталь; соединитальный патрубок; штуцер3) pl обвязка ( трубопроводами)•- bias cut hydrocouple connectionto make a connection — наращивать ( бурильную колонну); навинчивать свечу на бурильную колонну;
- bolted connection
- buttress connection
- casing connection
- clamp connection
- discharge connection
- drain connection
- drill-pipe connection
- filling connection
- flanged connection
- fourway connection
- gas connections
- gastight connection
- gimbal connection
- hose connection
- hydrant connection
- inlet-pipe connection
- internal flush connection
- jumper connection
- jumpover connection
- link connection
- long thread and coupling connection
- marine riser connection
- outlet connection
- outlet-pipe connection
- pigtail connection
- pipe connection
- releasable connection
- riser lock connection
- screwed connection
- short thread and coupling connection
- Siamese connection
- suction connection
- surface connection
- tank connections
- tank hoop connection
- tapered connection
- threaded connection
- threaded hose connection
- tight connection
- underwater wellhead connection
- wellhead connections
- wye connection
- Y-connection* * *• муфта• обвязка• патрубокАнгло-русский словарь нефтегазовой промышленности > connection
36 ECS
1) Общая лексика: Education Counselling Service2) Компьютерная техника: embedded computer system3) Авиация: система кондиционирования воздуха4) Американизм: Ethics Compliance Standard5) Спорт: Extreme Combat Specialists6) Военный термин: Electronic Combat Support, Engineer Combat System, Exercise Control System, electronic control sensor, electronic countermeasures squadron, electronic countermeasures system, emission control system, engagement control system, engineering change schedule, engineering change sheet, entry control subsystem, environmental control system, equipment concentration site, equipment configuration study, exploder control sensor7) Техника: European fixed service satellite system, edge control seamer, editing control suite, electrical connector subassembly, electrocardioscanner, electronic clutch system, electronic composing system, electronic cooling system, electronics control system, emergency control station, enable control system, engineering control system, environmental chamber shroud, error correction servo, error correction signals, extended core storage, extensive communications system, extinction-coagulation-sedimentation8) Бухгалтерия: Electronic Clearing Service9) Автомобильный термин: evaporation control system (Chrysler)10) Сокращение: Ecuadorian Sucre, Electrochemical Society, Electronic Combat Squadron (USA), Electronic Commerce Services (secure data transmission), Electronic Courier Services (secure data transmission) March 2000, Emergency Coolant System, Engagement Control Station, European Communications Satellite, Experimental Communications Satellite11) Университет: Electronic And Computer Science, Electronic Citation System12) Электроника: European Communication Satellite13) Вычислительная техника: Enhanced Chip Set (Amiga, Commodore), Environmental Control System (Space)14) Связь: emergency call service15) Космонавтика: Environmental Control Subsystem, European regional communication satellite programme, система климатизации, система контроля среды, система обеспечения температурно-влажностного режима и режима чистоты16) Фирменный знак: Economic Consultancy House, Electronic Control Services Company, Engineered Compost Systems17) Экология: ЭКС18) Энергетика: Energy Charter Secretariat19) СМИ: English Communications Service20) Деловая лексика: Energy Consumption Saver, Enhanced Customer Service21) Глоссарий компании Сахалин Энерджи: Экологическая компания Сахалина (ЭКС)22) Образование: Educational Cost Sharing, Exceptional Children Services23) Сетевые технологии: Enterprise Control Station, external cache socket24) Автоматика: expert control system25) Авиационная медицина: environment(al) control system26) Макаров: energy control system27) Безопасность: Encryption Control Signal, Encryption Control System, electronic countersurveillance28) Расширение файла: Electronic Chart Systems, Enhanced Chip Set29) Нефть и газ: Ecological Company of Sakhalin, Environmental Company of Sakhalin, Elemental Capture Sonde30) Общественная организация: Education Commission of the States31) НАСА: EOF Core System37 ecs
1) Общая лексика: Education Counselling Service2) Компьютерная техника: embedded computer system3) Авиация: система кондиционирования воздуха4) Американизм: Ethics Compliance Standard5) Спорт: Extreme Combat Specialists6) Военный термин: Electronic Combat Support, Engineer Combat System, Exercise Control System, electronic control sensor, electronic countermeasures squadron, electronic countermeasures system, emission control system, engagement control system, engineering change schedule, engineering change sheet, entry control subsystem, environmental control system, equipment concentration site, equipment configuration study, exploder control sensor7) Техника: European fixed service satellite system, edge control seamer, editing control suite, electrical connector subassembly, electrocardioscanner, electronic clutch system, electronic composing system, electronic cooling system, electronics control system, emergency control station, enable control system, engineering control system, environmental chamber shroud, error correction servo, error correction signals, extended core storage, extensive communications system, extinction-coagulation-sedimentation8) Бухгалтерия: Electronic Clearing Service9) Автомобильный термин: evaporation control system (Chrysler)10) Сокращение: Ecuadorian Sucre, Electrochemical Society, Electronic Combat Squadron (USA), Electronic Commerce Services (secure data transmission), Electronic Courier Services (secure data transmission) March 2000, Emergency Coolant System, Engagement Control Station, European Communications Satellite, Experimental Communications Satellite11) Университет: Electronic And Computer Science, Electronic Citation System12) Электроника: European Communication Satellite13) Вычислительная техника: Enhanced Chip Set (Amiga, Commodore), Environmental Control System (Space)14) Связь: emergency call service15) Космонавтика: Environmental Control Subsystem, European regional communication satellite programme, система климатизации, система контроля среды, система обеспечения температурно-влажностного режима и режима чистоты16) Фирменный знак: Economic Consultancy House, Electronic Control Services Company, Engineered Compost Systems17) Экология: ЭКС18) Энергетика: Energy Charter Secretariat19) СМИ: English Communications Service20) Деловая лексика: Energy Consumption Saver, Enhanced Customer Service21) Глоссарий компании Сахалин Энерджи: Экологическая компания Сахалина (ЭКС)22) Образование: Educational Cost Sharing, Exceptional Children Services23) Сетевые технологии: Enterprise Control Station, external cache socket24) Автоматика: expert control system25) Авиационная медицина: environment(al) control system26) Макаров: energy control system27) Безопасность: Encryption Control Signal, Encryption Control System, electronic countersurveillance28) Расширение файла: Electronic Chart Systems, Enhanced Chip Set29) Нефть и газ: Ecological Company of Sakhalin, Environmental Company of Sakhalin, Elemental Capture Sonde30) Общественная организация: Education Commission of the States31) НАСА: EOF Core System38 connection
1) соединение; сочленение2) связь; контакт3) соединение; соединительная деталь4) патрубок; штуцер•- assembly connection
- bevel connection
- bolted connection
- bridge connection
- butt connection
- butt-lap connection
- butt-strap connection
- cap screw connection
- cascade connection
- chain connection
- combined connection
- complete bridge connection
- component connection
- cotter connection
- cross connection
- cylindrical connection
- delta connection
- detached connection
- differential connection
- direct connection
- drive ball connection
- drive connection
- dynamic connection
- earth connection
- electrical connection
- emergency connection
- end connection
- face connection
- fiber optic connection
- fixed connection
- flange connection
- flanged face connection
- flexible cable connection
- folding connection
- front connection
- glued connection
- ground connection
- high-torque drive connection
- hose connection
- incomplete bridge connection
- inlet connection
- intelligent connection of perception to action
- interlayer connection
- internal connection
- key connection
- keyed connection
- keyless connection
- link connection
- loose connection
- low-torque drive connection
- master-slave connection
- movable connection
- nipple connection
- nonpositive connection
- optical connection
- parallel connection
- parasitic connection
- permanent connection
- pin connection
- pipe connection
- pipe tap connection
- pivot connection
- pivotal connection
- planar connection
- plant-floor connection
- plug-and-jack connection
- plug-and-socket connection
- pneumatic connections
- pressure connection
- profile connection
- push-in connection
- rear connection
- reciprocating motion connection
- rectifier connection
- releasable connection
- riveted connection
- rotating air connection
- rotating connection
- screw connection
- seamless connection
- self-sealing connection
- semirigid connection
- series connection
- servo connection
- side connection
- sleeve connection
- software connections
- solder connection
- soldered connection
- spherical connection
- spline connection
- star connection
- static connection
- step connection
- suction connection
- tandem connection
- thread connection
- threaded connection
- transverse connection
- tubing connections
- welded connection
- yielding connectionEnglish-Russian dictionary of mechanical engineering and automation > connection
39 coupling
сцепление; фрикцион; муфта; зубчатая муфта; кулачковая муфта; муфта сцепления; защёлка; собачка; кулак; сопряжение; сочленение (напр. шарнирного устройства); связь (по радио); взаимосвязь; взаимодействие; сцепной прибор; сцепка; цепной замок; стяжка; спаривание; соединение; соединительное звено (напр. цепи); стыковка; связывание; увязка; внедрение; доведение (результатов исследований); II соединительный; связывающий- coupling bar - coupling between oscillations - coupling cable - coupling component - coupling cone - coupling connector - coupling device - coupling edge - coupling end - coupling engagement - coupling error - coupling face - coupling fitting - coupling flange - coupling fork - coupling gasket - coupling half - coupling head - coupling hitch - coupling hook - coupling joint - coupling lever - coupling lifter - coupling link - coupling lock - coupling mechanism - coupling member - coupling nut - coupling of Asiatic profile - coupling of European profile - coupling of pipeline - coupling of pipeline sections - coupling of serie B - coupling pawl - coupling piece - coupling pipe - coupling point - coupling power - coupling ring - coupling rod - coupling screw - coupling screwing-on - coupling shaft - coupling site - coupling size - coupling sleeve - coupling socket - coupling spindle - coupling system - coupling unit - coupling with resilient members - coupling with rubber bushings - adapter coupling - additional coupling - air hose coupling - air-line coupling - ajax flexible coupling - annular coupling - Bibly coupling - capacitive coupling - cascade coupling - cased-muff coupling - clamp shaft coupling - cone coupling - cone-vice coupling - control coupling - cross coupling - cross sliding coupling - curvex coupling - Curvic coupling - cylindrical single-piece body coupling - diaphragm coupling - direct coupling- disk- disengaging coupling - dog coupling - double tapered coupling - double universal coupling - dresser coupling - drum disconnect coupling - eddy current coupling - elastic coupling - electric coupling - electrical coupling - electromagnetic coupling - expanding coupling - expansible coupling - expansion coupling - extension coupling - face tooth coupling - Falk coupling - fast coupling - feedback coupling - female threaded swivel coupling - fire-hose coupling - fixed coupling - fixed Curvic coupling - flange coupling - flanged coupling - flare quick tapered coupling from nickel-plated brass - flexible coupling - flexible block coupling - floating coupling - fluid coupling - fluid coupling adjustable by variable configuration of working space - fluid coupling adjustable by variable filling - fluid coupling with circulation - fluid coupling without circulation - fluid coupling without support - fluid drive coupling - fluted coupling - friction cone coupling - friction coupling - friction clutch coupling - full-floating coupling - funnel coupling - gear coupling - gear tooth-type coupling - gum coupling - hardened coupling - Hirth coupling - Hirth gear coupling - Hirth-ring coupling - Hirth tooth coupling - holdfast coupling - hydraulic coupling - hysteresis coupling - gas male threaded quick coupling - induction coupling - infused emitter coupling - interstage coupling - inverse coupling - jaw coupling - joint coupling - joint-type coupling - keyed coupling - lamination coupling - leather-belt coupling - leather-link coupling - link coupling - load limiting fluid coupling - loading coupling - loose coupling - loose-sliding coupling - Lord coupling - lub'air quick coupling - magnetic coupling - magnetic particle coupling - main coupling - make-and-break coupling - master control coupling - mixed coupling - movable coupling - muff coupling - multidisk coupling - needle coupling - nonlinear coupling - Oldham coupling - Oldum coupling - olive coupling for steel- copper- optimum coupling - overload coupling - parallel two-space fluid coupling - pawl coupling - permanent coupling - permanent shaft coupling - pill-to-pin coupling - pin coupling - pin-and-bushing flexible coupling - pin flexible coupling - pipe coupling - pivot-type coupling - plate coupling - plate-type coupling - pneumatic coupling - powder coupling - pressure coupling - prolac standard coupling with pushbutton for quick disconnection - protecting fluid coupling - pull rod coupling - push-connect air coupling - quick-acting coupling - quick-action coupling - quick-connect coupling - quick olive coupling for compressed air- water- quick-release coupling - rapid coupling - ratchet coupling - reducer coupling - reducing coupling - releasing Curvic coupling - resilient-material coupling - ribbed clamp coupling - rigid coupling - ring coupling - ring compression coupling - rod coupling - rod reducing coupling - roller chain flexible coupling - rope coupling - rotary coupling - rubber annulus coupling - rubber-packed coupling - rubber spider coupling - rubber tire coupling - safety coupling - scoop controlled fluid coupling - screw coupling - screwed coupling - self-aligning coupling - Sellers coupling - semipermanent coupling - semiuniversal Curvic coupling - series two-space fluid coupling - shaft coupling - shear-pin coupling - shift Curvic coupling - single-space fluid coupling - single-support fluid coupling - single universal coupling - sleeve coupling - sleeve-type coupling - slider coupling - sliding coupling - slip coupling - slip joint coupling - solid coupling - spiral jaw coupling - spline coupling - split coupling - split muff coupling - spring coupling - spring-loaded coupling - square-jaw coupling - star coupling - starting-breaking fluid coupling - starting fluid coupling - stationary coupling - straight pipe coupling - stud-retained coupling - sucker-rod coupling - swivel coupling - swivel hose quick release safety coupling - synchronous coupling - teflon-coated tapered threaded male quick release safety coupling - thimble coupling - threaded coupling - threadless coupling - through coupling - tight coupling - toothed coupling - toothed face coupling - tooth ring coupling - tooth-type coupling - torque coupling - trailer coupling - tube coupling - tubing coupling - turned-down coupling - turntable coupling - two-space fluid coupling - two-support fluid coupling - union coupling - universal coupling - universal spindle coupling - variable coupling - vernier coupling - viscous coupling - weak coupling - Westinghouse-Nuttall coupling - working control coupling - zigzag spring coupling40 plug-in
1. n спец. штепсельное соединение; вставная муфтаplug-in connection — вставное соединение; штыковой разъём
2. a спец. вставной; штепсельный, штыревой, со штепсельным контактом3. a спец. блочный, съёмный, сменный, заменяемыйplug-in components — сменные блоки, детали
plug-in assembly — съемная блочная конструкция; съемный блок
plug-in board — съемная плата; сменная плата
Синонимический ряд:plug (noun) electrical outlet; outlet; plug; socket; terminalСтраницыСм. также в других словарях:
Socket — can refer to:In mechanics: * Socket wrench, a type of wrench that uses separate, removable sockets to fit different sizes of nuts and bolts * Socket head screw, a screw (or bolt) with a cylindrical head containing a socket into which the… … Wikipedia
Socket 604 — Type PGA ZIF Chip form factors pin grid array Contacts 604 Processors Intel Xeon … Wikipedia
Socket — Sock et, n. [OE. soket, a dim. through OF. fr. L. soccus. See {Sock} a covering for the foot.] 1. An opening into which anything is fitted; any hollow thing or place which receives and holds something else; as, the sockets of the teeth. [1913… … The Collaborative International Dictionary of English
Socket bolt — Socket Sock et, n. [OE. soket, a dim. through OF. fr. L. soccus. See {Sock} a covering for the foot.] 1. An opening into which anything is fitted; any hollow thing or place which receives and holds something else; as, the sockets of the teeth.… … The Collaborative International Dictionary of English
Socket chisel — Socket Sock et, n. [OE. soket, a dim. through OF. fr. L. soccus. See {Sock} a covering for the foot.] 1. An opening into which anything is fitted; any hollow thing or place which receives and holds something else; as, the sockets of the teeth.… … The Collaborative International Dictionary of English
Socket pipe — Socket Sock et, n. [OE. soket, a dim. through OF. fr. L. soccus. See {Sock} a covering for the foot.] 1. An opening into which anything is fitted; any hollow thing or place which receives and holds something else; as, the sockets of the teeth.… … The Collaborative International Dictionary of English
Socket pole — Socket Sock et, n. [OE. soket, a dim. through OF. fr. L. soccus. See {Sock} a covering for the foot.] 1. An opening into which anything is fitted; any hollow thing or place which receives and holds something else; as, the sockets of the teeth.… … The Collaborative International Dictionary of English
Socket wrench — Socket Sock et, n. [OE. soket, a dim. through OF. fr. L. soccus. See {Sock} a covering for the foot.] 1. An opening into which anything is fitted; any hollow thing or place which receives and holds something else; as, the sockets of the teeth.… … The Collaborative International Dictionary of English
Socket 940 — is a 940 pin socket for 64 bit AMD server processors. The socket is entirely covered with leads, except for four key pins used to align the processor. AMD Opterons and the older AMD Athlon 64 FX (FX 51) use Socket 940. Being an intended server… … Wikipedia
Socket Bombing — is the name given to a type of direct action performed as a protest against excessive electricity consumption. It is derived from the actions of the [http://clanduneon.over blog.com/5 index.html Clan du Néon] . It involves purposfully causing a… … Wikipedia
Socket 6 — was a 486 generation CPU socket, a slightly modified version of the more common Socket 3.Intel designed this new standard near the end of the 80486 s market life,so few motherboards were produced that used it, especially as the Socket 3 standard… … Wikipedia
Перевод: с английского на русский
с русского на английский- С русского на:
- Английский
- С английского на:
- Все языки
- Арабский
- Венгерский
- Греческий
- Датский
- Исландский
- Испанский
- Итальянский
- Йоруба
- Латышский
- Литовский
- Марийский
- Мокшанский
- Немецкий
- Норвежский
- Польский
- Португальский
- Румынский, Молдавский
- Русский
- Словацкий
- Словенский
- Тамильский
- Турецкий
- Финский
- Французский
- Чешский
- Шведский
- Эрзянский