-
1 падение или повышение напряжения при заданном режиме нагрузки
падение или повышение напряжения при заданном режиме нагрузки
Разность между напряжением холостого хода обмотки и напряжением на ее выводах при заданных нагрузке и коэффициенте мощности при условии, что к другой (или к одной из других) обмотке(ок) подведено напряжение, равное:
- номинальному, если трансформатор включен на основное ответвление (в этом случае напряжение холостого хода рассматриваемой обмотки равно номинальному);
- напряжению другого ответвления, на которое включен трансформатор. Падение или повышение напряжения обычно выражают в процентах напряжения холостого хода рассматриваемой обмотки.
Примечание — В многообмоточном трансформаторе падение или повышение напряжения зависит от нагрузки и коэффициента мощности не только данной обмотки, но и других обмоток
(МЭС 421-07-03).
[ ГОСТ 30830-2002]EN
voltage drop or rise for a specified load condition
voltage regulation for a specified load condition
the arithmetic difference between the no-load voltage of a winding and the voltage developed at the terminals of the same winding at a specified load and power factor, the voltage supplied to (one of) the other winding(s) being equal to:
- its rated value if the transformer is connected on the principal tapping (the no-load voltage of the former winding is then equal to its rated value);
- the tapping voltage if the transformer is connected on another tapping.
This difference is generally expressed as a percentage of the no-load voltage of the former winding
NOTE – For multi-winding transformers, the voltage drop or rise depends not only on the load and power factor of the winding itself, but also on the load and power factor of the other windings
[IEV number 421-07-03]FR
hute ou augmentation de tension pour une condition de charge spécifiée
différence arithmétique entre la tension à vide d'un enroulement et la tension en charge aux bornes du même enroulement pour un courant de charge et un facteur de puissance spécifiés, la tension appliquée à l'autre (ou à l'un des autres) enroulement(s) étant égale:
- à sa valeur assignée, si le transformateur est connecté sur la prise principale (la tension à vide du premier enroulement étant alors égale à sa valeur assignée);
- à la tension de prise si le transformateur est connecté sur une autre prise.
Cette différence s'exprime généralement sous la forme d'un pourcentage de la tension à vide du premier enroulement
NOTE – Pour les transformateurs à plus de deux enroulements, la chute ou l'augmentation de tension dépend non seulement de la charge et du facteur de puissance de l'enroulement lui-même, mais aussi de la charge et du facteur de puissance des autres enroulements.
[IEV number 421-07-03]Тематики
Классификация
>>>EN
- voltage drop or rise for a specified load condition
- voltage regulation for a specified load condition
DE
FR
Русско-французский словарь нормативно-технической терминологии > падение или повышение напряжения при заданном режиме нагрузки
-
2 напряжение стабилизации стабилитрона
напряжение стабилизации стабилитрона
Uст
Uz
Значение напряжения стабилитрона при протекании тока стабилизации.
[ ГОСТ 25529-82]Тематики
Обобщающие термины
EN
DE
FR
81. Напряжение стабилизации стабилитрона
D. Z-Spannung der Z-Diode
E. Working voltage (of voltage regulator diode)
F. Tens on de régulation
Источник: ГОСТ 25529-82: Диоды полупроводниковые. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-французский словарь нормативно-технической терминологии > напряжение стабилизации стабилитрона
-
3 НКУ распределения и управления
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
Русско-французский словарь нормативно-технической терминологии > НКУ распределения и управления
-
4 временная нестабильность напряжения стабилизации стабилитрона
временная нестабильность напряжения стабилизации стабилитрона
δUст
δUZ
Отношение наибольшего изменения напряжения стабилизации стабилитрона к начальному значению напряжения стабилизации за заданный интервал времени.
[ ГОСТ 25529-82]Тематики
Обобщающие термины
EN
DE
FR
87. Временная нестабильность напряжения стабилизации стабилитрона
D. Zeitliche Instabilitat der Z-Spannung der Z-Diode
E. Working voltage long-term instability
F. Instabilité à long terme de la tension de régulation
δUст
Отношение наибольшего изменения напряжения стабилизации стабилитрона к начальному значению напряжения стабилизации за заданный интервал времени
Источник: ГОСТ 25529-82: Диоды полупроводниковые. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-французский словарь нормативно-технической терминологии > временная нестабильность напряжения стабилизации стабилитрона
-
5 дифференциальное сопротивление стабилитрона
дифференциальное сопротивление стабилитрона
rст
rz
Дифференциальное сопротивление при заданном значении тока стабилизации стабилитрона.
[ ГОСТ 25529-82]Тематики
Обобщающие термины
EN
DE
FR
84. Дифференциальное сопротивление стабилитрона
D. Z-Widerstand der Z-Diode
E. Differential resistance within the working voltage range
F. Résistance différentielle dans la zone des tensions de régulation
rст
Дифференциальное сопротивление при заданном значении тока стабилизации стабилитрона
Источник: ГОСТ 25529-82: Диоды полупроводниковые. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-французский словарь нормативно-технической терминологии > дифференциальное сопротивление стабилитрона
-
6 температурный коэффициент напряжения стабилизации стабилитрона
температурный коэффициент напряжения стабилизации стабилитрона
αUст
αUz
Отношение относительного изменения напряжения стабилизации стабилитрона к абсолютному изменению температуры окружающей среды при постоянном значении тока стабилизации
[ ГОСТ 25529-82]Тематики
Обобщающие термины
EN
DE
FR
85. Температурный коэффициент напряжения стабилизации стабилитрона
D. Temperaturkoeffizient der Z-Spannung der Z-Diode
E. Temperature coefficient of working voltage
F. Coefficient de temperature de la tension de régulation
αUст
Отношение относительного изменения напряжения стабилизации стабилитрона к абсолютному изменению температуры окружающей среды при постоянном значении тока стабилизации
Источник: ГОСТ 25529-82: Диоды полупроводниковые. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-французский словарь нормативно-технической терминологии > температурный коэффициент напряжения стабилизации стабилитрона
-
7 ток стабилизации стабилитрона
ток стабилизации стабилитрона
Iст
Iz
Значение постоянного тока, протекающего через стабилитрон в режиме стабилизации.
[ ГОСТ 25529-82]Тематики
Обобщающие термины
EN
DE
FR
82. Ток стабилизации стабилитрона
D. Z-Strom der Z-Diode
E. Continuous current within the working voltage range
F. Courant continu inverse pour la gamme des tensions de régulation
Iст
Значение постоянного тока, протекающего через стабилитрон в режиме стабилизации
Источник: ГОСТ 25529-82: Диоды полупроводниковые. Термины, определения и буквенные обозначения параметров оригинал документа
Русско-французский словарь нормативно-технической терминологии > ток стабилизации стабилитрона
-
8 НКУ распределения и управления для строительных площадок (НКУ СП)
НКУ распределения и управления для строительных площадок (НКУ СП)
Комбинация одного или нескольких трансформаторных устройств или коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты и регулирования со всеми внутренними электрическими и механическими соединениями и конструктивными элементами, разработанная и изготовленная для применения на любых строительных площадках — для наружной и внутренней установки.
[ ГОСТ Р 51321. 4-2000 ( МЭК 60439-4-90)]EN
low-voltage switchgear and controlgear assembly for construction sites (ACS)
combination of one or several transforming or switching devices with associated control, measuring, signalling, protective and regulating equipment complete with all their internal electrical and mechanical connections and structural parts, designed and built for use on all construction sites, indoors and outdoors
[IEC 60439-4, ed. 2.0 (2004-06)]FR
ensemble d'appareillage à basse tension utilisé sur les chantiers (EC)
combinaison d'un ou de plusieurs appareils de transformation ou de connexion avec équipements associés de commande, de mesure, de signalisation, de protection et de régulation complètement assemblés avec toutes leurs liaisons internes électriques et mécaniques et leurs éléments de construction (voir 2.4), conçue et construite pour être utilisée sur tous les chantiers, à l'intérieur et à l'extérieur.
[IEC 60439-4, ed. 2.0 (2004-06)]
Рис. ABB
Рис. ABB
Рис. ABBНКУ СП, устанавливаемое на ножках
НКУ СП, закрепляемое на вертикальной поверхности
НКУ СП розеточное
Параллельные тексты EN-RU
Assemblies for construction sites have different dimensions, ranging from the simple socket-outlet units to proper distribution boards in metal enclosure or insulating material.
These assemblies are usually mobile.
The Standard IEC 60439-4 establishes the particular requirements for this type of assemblies, making specific reference to mechanical strength and resistance to corrosion.
[ABB]НКУ для строительных площадок имеют разные размеры и функции - от простых розеточных до распределительных панелей в металлической или пластмассовой оболочке.
Данные НКУ обычно являются переносными.
Стандарт МЭК 60439-4 устанавливает дополнительные требования для НКУ данного типа, особенно по механической прочности и коррозионной стойкости.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
- ACS
- assemblies for construction sites
- low-voltage switchgear and controlgear assembly for construction sites
FR
Русско-французский словарь нормативно-технической терминологии > НКУ распределения и управления для строительных площадок (НКУ СП)
-
9 вспомогательная цепь НКУ
вспомогательная цепь НКУ
Все токоведущие части НКУ, включенные в цепь, предназначенную для управления, измерения, сигнализации, регулирования, обработки и передачи данных и т. д. и не являющуюся главной цепью.
Примечание — Цепи управления и вспомогательные цепи коммутационных аппаратов относятся к вспомогательным цепям.
(МЭС 441-13-03, с изменением)
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
вспомогательная цепь НКУ
Совокупность токоведущих частей комплекта, входящих в цепь (кроме главной цепи), предназначенную для управления, измерения, сигнализации, регулирования и обработки данных и т.д.
Примечание — Вспомогательные цепи комплекта включают цепи управления и вспомогательные цепи коммутационных устройств.
[ ГОСТ Р МЭК 61439.1-2013]EN
auxiliary circuit (of an assembly)
all the conductive parts of an assembly of switchgear and controlgear included in a circuit (other than the main circuit) intended to control, measure, signal and regulate
NOTE – The auxiliary circuits of an assembly include the control and auxiliary circuits of the switching devices.
[IEV number 441-13-03]FR
circuit auxiliaire (d'un ensemble)
toutes les pièces conductrices d'un ensemble insérées dans un circuit, autre que le circuit principal, destinées à la commande, la mesure, la signalisation et la régulation
NOTE – Les circuits auxiliaires d'un ensemble comprennent les circuits de commande et les circuits auxiliaires des appareils de connexion.
[IEV number 441-13-03]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > вспомогательная цепь НКУ
См. также в других словарях:
Voltage regulation — In electrical engineering, particularly power engineering, voltage regulation is the ability of a system to provide near constant voltage over a wide range of load conditions. It is a dimensionless quantity defined as::VR = frac{V {nl} V {fl{V… … Wikipedia
Voltage droop — is the intentional loss in output voltage from a device as it drives a load. Employing droop in a voltage regulation circuit increases the headroom for load transients.Although it may seem counterproductive, a series resistor is included between… … Wikipedia
Voltage regulator — A popular three pin 12 V DC voltage regulator IC. A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. A voltage regulator may be a simple feed forward design or may include negative feedback … Wikipedia
Voltage regulator tube — A voltage regulator tube (VR tube) is an electronic component used as a shunt regulator to hold a voltage constant at a pre determined level.Physically, these devices resemble vacuum tubes, but there are two main differences: * Their glass… … Wikipedia
Voltage-dependent calcium channel — Voltage dependent calcium channels (VDCC) are a group of voltage gated ion channels found in excitable cells (e.g., muscle, glial cells, neurons, etc.) with a permeability to the ion Ca2+.[1][2] These channels are slightly permeable to sodium… … Wikipedia
Regulation — This article is for the legal term. For regulation of genes, see regulation of gene expression. For the regulation of sports, see Regulation of sport. For regulation in electrical systems see Voltage regulator. For biological regulation, see… … Wikipedia
regulation — /reg yeuh lay sheuhn/, n. 1. a law, rule, or other order prescribed by authority, esp. to regulate conduct. 2. the act of regulating or the state of being regulated. 3. Mach. the percentage difference in some quantity related to the operation of… … Universalium
Voltage-gated potassium channel — Ion channel (eukariotic) Potassium channel, structure in a membrane like environment. Calculated hydrocarbon boundaries of the lipid bilayer are indicated by red and blue dots. Identifiers Symbol Ion trans … Wikipedia
régulation par variation de tension — reguliavimas keičiant įtampą statusas T sritis automatika atitikmenys: angl. variable voltage control vok. Regelung durch Spannungsänderung, f rus. регулирование изменением напряжения, n pranc. régulation par variation de tension, f … Automatikos terminų žodynas
Dynamic voltage scaling — is a power management technique in computer architecture, where the voltage used in a component is increased or decreased, depending upon circumstances. Dynamic voltage scaling to increase voltage is known as overvolting; dynamic voltage scaling… … Wikipedia
Load regulation — is the capability to maintain a constant voltage (or current) level on the output channel of a power supply despite changes in load [cite web|title=Line and Load Regulation for Programmable DC Power Supplies and Precision DC Sources Developer… … Wikipedia