-
1 влажная уборка пола
влажная уборка пола
Процесс очистки и/или ухода за полом, при котором пол обрабатывается такими жидкими реагентами, применение которых не исключает кратковременного образования луж и промокания покрытия пола.
Примечание - Примерами влажной уборки являются влажная чистка жесткой щеткой, ручное или механическое смывание.
[ ГОСТ Р МЭК 61084-2-2-2007]EN
wet-treatment of floor
a process for cleaning and/or care by which the floor is treated with liquid agents such that pools of liquid, or soaking of the floor covering for a brief period of time, cannot be excluded.
NOTE Examples of wet treatment are: wet scrubbing, manual or mechanical wiping.
[IEC 61084-2-2, ed. 1.0 (2003-05)]FR
traitement humide du sol
procédé de nettoyage et/ou d’entretien par lequel le sol est traité avec des agents de traitement liquides tels que l'on ne puisse pas exclure que des flaques puissent se former ou que le revêtement de sol soit imbibé pendant une période brève
NOTE Des exemples de traitement humide sont: brossage humide, nettoyage manuel ou mécanique à l'éponge.
[IEC 61084-2-2, ed. 1.0 (2003-05)]Тематики
- электропроводка, электромонтаж
EN
FR
Русско-французский словарь нормативно-технической терминологии > влажная уборка пола
-
2 ложный запуск ГТД
ложный запуск ГТД
ложный запуск
ЛЗ
Принудительная раскрутка, ротора ГТД пусковым устройством с подачей топлива в камеру сгорания при выключенной системе зажигания.
[ ГОСТ 23851-79]Тематики
Синонимы
EN
DE
FR
232. Ложный запуск ГТД
Ложный запуск
ЛЗ
D. Scheinanlauf
Е. Wet motoring
F. Démarrage faux
Принудительная раскрутка ротора ГТД пусковым устройством с подачей топлива в камеру сгорания при выключенной системе зажигания
Источник: ГОСТ 23851-79: Двигатели газотурбинные авиационные. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > ложный запуск ГТД
-
3 мокрое смешивание металлических порошков
мокрое смешивание металлических порошков
мокрое смешивание
Смешивание металлических порошков с добавлением жидких веществ, препятствующих разделению смеси по компонентам.
[ ГОСТ 17359-82]Тематики
Синонимы
EN
DE
FR
12. Мокрое смешивание металлических порошков
Мокрое смешивание
D. Nassmischen
Е. Wet mixing
F. Mélange humide
Источник: ГОСТ 17359-82: Порошковая металлургия. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > мокрое смешивание металлических порошков
-
4 мокрый процесс
мокрый процесс
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
wet process
Process used to remove particulate matter and/or gaseous pollutants by means of an aqueous stream or slurry. (Source: KORENa)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > мокрый процесс
-
5 мокрый скруббер
мокрый скруббер
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
wet scrubber
1) An air cleaning device that literally washes out the dust. Exhaust air is forced into a spray chamber, where fine water particles cause the dust to drop from the air stream. The dust-ladden water is then treated to remove the solid material and is often recirculated. 2) Equipment through which a gas is passed to remove impurities (solid, liquid, or gaseous particles) by intimate contact with a suitable liquid, usually an aqueous medium. (Source: LANDY / BRACK / ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > мокрый скруббер
-
6 осадок на фильтре
осадок на фильтре
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
filter cake
Accumulated solids, wet or dry, generated by any filtration process, including accumulation on fabric filters in air filtering processes, or accumulation of wet solids in liquid filtering processes. (Source: EED / ISEP)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > осадок на фильтре
-
7 паровая стационарная турбина насыщенного пара
паровая стационарная турбина насыщенного пара
турбина насыщенного пара
Паровая стационарная турбина, в которой используется в качестве свежего насыщенный пар.
[ ГОСТ 23269-78]Тематики
Синонимы
EN
DE
FR
18. Паровая стационарная турбина насыщенного пара
Турбина насыщенного пара
D. Sattdampfturbine
E. Wet steam turbine
F. Turbine a vapeur saturee
Паровая стационарная турбина, в которой используется в качестве свежего насыщенный пар
Источник: ГОСТ 23269-78: Турбины стационарные паровые. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > паровая стационарная турбина насыщенного пара
-
8 отёк лёгких
-
9 метод мокрого песка
nconstruct. procédé wet sand (консервация свежего бетона) -
10 отёк лёгких
-
11 влагопрочная бумага
влагопрочная бумага
Бумага, подвергнутая специальной поверхностной обработке или обработке в массе для повышения прочности во влажном состоянии.
[ ГОСТ 17586-80]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > влагопрочная бумага
-
12 влагопрочность бумаги (картона)
- résistance apparente à l’état humide
влагопрочность бумаги (картона)
Свойство бумаги (картона) сохранять прочность при увлажнении.
[ ГОСТ 17052-86]Тематики
EN
DE
FR
- résistance apparente à l’état humide
Русско-французский словарь нормативно-технической терминологии > влагопрочность бумаги (картона)
-
13 влажный пар
влажный пар
Равновесная смесь, состоящая из паровой и жидкой фаз.
[Сборник рекомендуемых терминов. Выпуск 103. Термодинамика. Академия наук СССР. Комитет научно-технической терминологии. 1984 г.]
влажный пар
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]
Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > влажный пар
-
14 газгольдер мокрый
газгольдер мокрый
Газгольдер переменного объёма с нижним стальным или железобетонным резервуаром, наполненным водой, и верхними стальными подъёмными и опускными звеньями, наполненными газом
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > газгольдер мокрый
-
15 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
16 камера горения топки стационарного котла
камера горения топки стационарного котла
камера горения
Часть топки стационарного котла, в которой происходит воспламенение и горение основной массы топлива.
[ ГОСТ 23172-78]Тематики
- котел, водонагреватель
Синонимы
EN
DE
FR
116. Камера горения топки стационарного котла
Камера горения
D. Brennkammer
E. Primary furnace (in wetbottom-furnace)
F. Chambre de combustion
Часть топки стационарного котла, в которой происходят воспламенение и горение основной массы топлива
Источник: ГОСТ 23172-78: Котлы стационарные. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > камера горения топки стационарного котла
-
17 камера охлаждения топки стационарного котла
камера охлаждения топки стационарного котла
камера охлаждения
Часть топки стационарного котла, в которой происходит догорание топлива и частичное охлаждение продуктов горения.
[ ГОСТ 23172-78]Тематики
- котел, водонагреватель
Синонимы
EN
DE
FR
117. Камера охлаждения топки стационарного котла
Камера охлаждения
D. Kuhlkammer
Е. Secondary furnace (in wetbottom furnace)
F. Chambre de refroidissement
Часть топки стационарного котла, в которой происходит догорание топлива и частичное охлаждение продуктов горения
Источник: ГОСТ 23172-78: Котлы стационарные. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > камера охлаждения топки стационарного котла
-
18 мангровое болото
мангровое болото
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
mangrove swamp
A wet, spongy area of land in tropical climates and along coastal regions that is dominated by mangrove trees and shrubs, particularly red mangroves (Rhizophora), black mangroves (Avicennia) and white mangroves (Laguncularia). (Source: FFD)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > мангровое болото
-
19 мелиорация земель
мелиорация земель
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
land reclamation
Making land capable of more intensive use by changing its general character, as by drainage of excessively wet land; irrigation of arid or semiarid land; or recovery of submerged land from seas, lakes and rivers. (Source: LANDY)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > мелиорация земель
-
20 мокрое протравливание семенного (посадочного) материал пестицидом
мокрое протравливание семенного (посадочного) материал пестицидом
Протравливание семенного (посадочного) материала погружением его в раствор, суспензию или эмульсию пестицида с последующим томлением и сушкой.
[ ГОСТ 21507-81]Тематики
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > мокрое протравливание семенного (посадочного) материал пестицидом
- 1
- 2
См. также в других словарях:
Wet Wet Wet — at the Montreux Pop Festival in Montreux, Switzerland May 1988 Background information Origin Clydebank, Scotland … Wikipedia
Wet Wet Wet — Марти Пеллоу солист группы … Википедия
Wet Seal — Wet Seal, Inc. Type Public (NASDAQ: WTSLA) Industry Retail Founded 1962 as Lorne s Headquarters Foothill Ranch, California … Wikipedia
Wet scrubber — is a form of pollution control technology. The term describes a variety of devices that use pollutants from a furnace flue gas or from other gas streams. In a wet scrubber, the polluted gas stream is brought into contact with the scrubbing liquid … Wikipedia
WET Web Tester — [ [http://wet.qantom.org Commercial Grade Web Automation Testing offering an Opensource alternative to Quicktest and Silktest ] ] is a web testing tool that drives an IE Browser directly and so the automated testing done is equivalent to how a… … Wikipedia
Wet wipe — Wet wipes (textile), unwrapped. A wet wipe, also known as a wet nap, wet towel, or a moist towelette, is a small moistened piece of paper or cloth that often comes folded and individually wrapped for convenience. Such towelettes are for cleansing … Wikipedia
WET (WET Design) — WET (Water Entertainment Technologies), also known as WET Design, is a water feature design firm based in Los Angeles, California, founded in 1983 by former Disney Imagineers Mark Fuller, Melanie Simon, and Alan Robinson. WET is best known for… … Wikipedia
WET (Computerspiel) — Wet Entwickler … Deutsch Wikipedia
Wet Wet Wet — Datos generales Origen Clydebank, Escocia Información artística … Wikipedia Español
wet — [wet] adj. wetter, wettest [ME < OE wæt, akin to ON vatr: for IE base see WATER] 1. moistened, covered, or saturated with water or other liquid 2. rainy; foggy; misty [a wet day] 3. not yet dry [wet paint] 4 … English World dictionary
Wet — (w[e^]t), a. [Compar. {Wetter}; superl. {Wettest}.] [OE. wet, weet, AS. w[=ae]t; akin to OFries. w[=e]t, Icel. v[=a]tr, Sw. v[*a]t, Dan. vaad, and E. water. [root]137. See {Water}.] [1913 Webster] 1. Containing, or consisting of, water or other… … The Collaborative International Dictionary of English