-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
2 геологический процесс
геологический процесс
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
geological process
Dynamic actions or events that occur at the Earth's surface due to application of natural forces resulting from gravity, temperature changes, freezing and thawing, chemical reactions, seismic shaking, and the agencies of wind and moving water, ice and snow. Where and when a force exceeds the strength of the earth material, the material is changed by deformation, translocation, or chemical reactions. (Source: DUNSTE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > геологический процесс
-
3 земная кора
земная кора
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
earth's crust
The outer layers of the Earth's structure, varying between 6 and 48 km in thickness, and comprising all the material above the Mohorovicic Discontinuity (a seismic discontinuity occurring between the crust of the earth and the underlying mantle; the discontinuity occurs at an average depth of 35 km below the continents and at about 10 km below the oceans). The earlier idea of a cool solid skin overlaying a hot molten interior has now been replaced by a concept of a crust composed of two shells: an inner basic unit composed of sima (oceanic crust) and an outer granitic unit composed of sial (continental crust). (Source: WHIT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > земная кора
-
4 седиментация (геол.)
седиментация (геол.)
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
sedimentation (geology)
The act or process of forming or accumulating sediment in layers, including such processes as the separation of rock particles from the material from which the sediment is derived, the transportation of these particles to the site of deposition, the actual deposition or settling of the particles, the chemical and other changes occurring in the sediment, and the ultimate consolidation of the sediment into solid rock. (Source: BJGEO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > седиментация (геол.)
-
5 функция почвы
функция почвы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
soil function
The main soil function is participation in the material transformation and migrating processes occurring in the natural environment on which the functioning of ecosystems depends. The most active participants in the occurring processes are microorganisms and invertebrates, whose activity, different variety, complex structure, and abundance accurately reflect the soil type and its characteristics: so they are important indicators of ecological stability. The variety of soil organisms determine its self-regulatory and self-cleaning capacity. (Source: NERIS)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > функция почвы
-
6 утилизация материалов военного назначения
утилизация материалов военного назначения
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
disposal of warfare materials
Disposal of the material remnants of war, which can seriously impede development and cause injuries and the loss of lives and property. The disposal of warfare waste is problematic because it can be highly dangerous, toxic, long-living and requires the utilization of specific and sophisticated technologies, particularly in the case of mines and unexploded bombs which have been left on the war territories. (Source: WPR)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > утилизация материалов военного назначения
-
7 процесс распространения через среду
процесс распространения через среду
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
propagation process
Process by which a disturbance at one point is propagated to another point more remote from the source with no net transport of the material of the medium itself; examples include the motion of electromagnetic waves, sound waves, hydrodynamic waves in liquids, and vibration waves in solids. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > процесс распространения через среду
-
8 археология
археология
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
archaeology
The scientific study of the material remains of the cultures of historical or prehistorical peoples. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > археология
-
9 радиоактивные осадки
радиоактивные осадки
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
radioactive fallout
The material that descends to the earth or water well beyond the site of a surface or subsurface nuclear explosion. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > радиоактивные осадки
-
10 вопрос школьной программы
вопрос школьной программы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
schoolwork
The material studied in or for an educational institution, comprising homework and work done in the classroom. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > вопрос школьной программы
-
11 выборка
<>выборка
-
[IEV number 151-16-19]
<>выборка
Часть генеральной совокупности элементов, которая охватывается наблюдением (часто ее называют выборочной совокупностью, а выборкой — сам метод выборочного наблюдения). В математической статистике принят принцип случайного отбора; это означает, что каждый элемент имеет равный шанс попасть в В. Различают В. возвратную и невозвратную. В первом случае каждый отобранный элемент возвращается в исследуемую совокупность до того, как произойдет отбор следующего элемента. Во втором — отобранный элемент «изымается» из дальнейшего рассмотрения. Причем невозвратная (или безвозвратная) В. может рассматриваться как возвратная, если она составляет малую часть совокупности. На практике используются следующие основные виды В.: Собственно случайная выборка. — когда объекты для изучения отбираются по жребию, на основе таблицы случайных чисел, и т.п. Систематическая (или механическая) выборка., когда отбор производится через определенный интервал (шаг отбора) из списка единиц совокупности, расположенных в нем в определенном порядке. Типическая выборка. — когда генеральная совокупность разбивается на типические группы или слои (страты) и внутри каждой группы производится (случайный или механический) отбор. Серийная выборка (иногда кластерная, от английского cluster sampling), смысл которой удобно пояснить на примере: чтобы определить для какого-то антропометрического обследования средний рост школьников-первоклассников, можно случайным или механическим способом выбрать город, в этом городе — район, в районе — школу, в школе — класс, а затем провести сплошное измерение роста всех учеников этого класса.
[ http://slovar-lopatnikov.ru/]EN
sample
one or more sampling items intended to provide information on the population or on the material
Source: ISO 3534-1 item 4.2 MOD
[IEV number 151-16-19]FR
échantillon, m
une ou plusieurs entités d'échantillonnage destinées à fournir des informations sur la population ou la matière
Source: ISO 3534-1, N° 4.2 MOD
[IEV number 151-16-19]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > выборка
-
12 защита природы
защита природы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
nature protection
Precautionary actions, procedures or installations undertaken to prevent or reduce harm to the elements of the material world that exist independently of human activity. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > защита природы
-
13 сбор отходов с сортировкой
сбор отходов с сортировкой
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
separated collection
The collection of individual components of solid waste from any source, usually separated into different collection containers, in order to recover, reuse or recycle the material or to facilitate its collection and disposal. (Source: GSW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > сбор отходов с сортировкой
-
14 физический процесс
физический процесс
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
physical process
A continuous action or series of changes which alters the material form of matter. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > физический процесс
-
15 хлорфторуглероды
хлорфторуглероды
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
chlorofluorocarbon
Gases formed of chlorine, fluorine, and carbon whose molecules normally do not react with other substances; they are therefore used as spray can propellants because they do not alter the material being sprayed. (Source: LANDY)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > хлорфторуглероды
-
16 расстояние утечки
расстояние утечки
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание. Стык между двумя элементами из изоляционного материала считают частью поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
расстояние утечки (см. приложение В)
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание — При определении расстояния утечки относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9
[ ГОСТ Р 50345-99( МЭК 60898-95)]
расстояние утечки по поверхности
-
[IEV number 151-15-50]
путь утечки
Кратчайшее расстояние вдоль поверхности изоляции между двумя проводящими частями или между проводящей частью и доступной поверхностью.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - A joint between two pieces of insulating material is considered part of the surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - For the purpose of determining a creepage distance to accessible parts, the accessible surface of an insulating enclosure is considered conductive as if it was covered by a metal foil wherever it can be touched by a hand or a standard test finger according to figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
creepage distance
shortest distance along the surface of insulation between two conductive parts or between a conductive part and the accessible surface
[IEC 60335-1, ed. 4.0 (2001-05)]
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts
[IEV number 151-15-50]FR
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Un joint entre deux portions de matière isolante est considéré comme faisant partie de la surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Pour la détermination d'une ligne de fuite pour des parties accessibles, la surface accessible d'une enveloppe isolante est considérée comme conductrice comme si elle était recouverte d'une feuille métallique à tout endroit où elle peut être touchée par la main ou par le doigt d'essai normalisé conforme à la figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
ligne de fuite
plus petite distance le long de la surface de l’isolation entre deux parties conductrices ou entre une partie conductrice et la surface accessible
[IEC 60335-1, ed. 4.0 (2001-05)]
ligne de fuite, f
distance la plus courte, le long de la surface d'un isolant solide, entre deux parties conductrices
[IEV number 151-15-50]1) Должно быть проводящими
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > расстояние утечки
-
17 толщина материала комбинированной гладкой и гофрированной трубы
толщина материала комбинированной гладкой и гофрированной трубы
-
[IEV number 442-02-22]EN
material thickness of a combined plain and corrugated conduit
the sum of the plain conduit material thickness and the corrugated material thickness
[IEV number 442-02-22]FR
épaisseur de matériau d'un conduit mixte lisse/annelé
somme de l'épaisseur de matériau du conduit lisse et de l'épaisseur de matériau du conduit annelé
[IEV number 442-02-22]Тематики
- электропроводка, электромонтаж
EN
DE
FR
- épaisseur de matériau d'un conduit mixte lisse/annelé
Русско-немецкий словарь нормативно-технической терминологии > толщина материала комбинированной гладкой и гофрированной трубы
-
18 активное вещество химического источника тока
- Gemisch von aktiver Masse, n
- aktive Masse, f
активное вещество химического источника тока
активное вещество
Вещество в гальваническом элементе, химическая энергия которого при разовом или многократном разряде превращается в электрическую.
[ ГОСТ 15596-82]
активное вещество
Вещество в свинцово-кислотной батарее, участвующее в электрохимической реакции производства тока. Активные вещества: анода – диоксид свинца (Pb2O), электролита – серная кислота (H2SO4) и катода – пористый свинец (Pb).
[ http:// www.energon.ru/support/publication/akkumulyatory_osnovnye_terminy_i_opredeleniya/]EN
active material
material which reacts chemically to produce electric energy when the cell discharges
NOTE – In secondary cells, the active material is restored to its original state during charge.
[IEV number 482-02-33]FR
matière active, f
matière qui réagit chimiquement pour produire de l’énergie électrique lorsque l'élément se décharge
NOTE – Pour les accumulateurs, la matière active est ramenée à son état initial pendant la charge.
[IEV number 482-02-33]Тематики
Классификация
>>>Синонимы
EN
DE
- aktive Masse, f
- Gemisch von aktiver Masse, n
FR
- matière active, f
Русско-немецкий словарь нормативно-технической терминологии > активное вещество химического источника тока
-
19 изоляционный материал
изоляционный материал
изолятор
-
[IEV number 151-15-35]EN
insulating material
insulant
material used to prevent electric conduction between conductive elements
NOTE – In the field of electromagnetism the term "insulant" is also used as a synonym for "insulating medium".
Source: 212-01-01 MOD, IEC 60050-121
[IEV number 151-15-35]FR
isolant, m
matériau isolant, m
matériau destiné à empêcher la conduction électrique entre des éléments conducteurs
NOTE – En électromagnétisme le terme "isolant" est aussi utilisé comme synonyme de "milieu isolant".
Source: 212-01-01 MOD, CEI 60050-121
[IEV number 151-15-35]Синонимы
EN
DE
FR
- isolant, m
- matériau isolant, m
Русско-немецкий словарь нормативно-технической терминологии > изоляционный материал
-
20 почвенный слой
почвенный слой
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
soil layer
Distinctive successive layers of soil produced by internal redistribution processes. Conventionally the layers have been divided into A, B and C horizons. The A horizon is the upper layer, containing humus and is leached and/or eluviated of many minerals. The B horizon forms a zone of deposition and is enriched with clay minerals and iron/aluminium oxides from the A layer. The C layer is the parent material for the present soil and may be partially weathered rock, transported glacial or alluvial material or an earlier soil. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > почвенный слой
См. также в других словарях:
The Material — Infobox musical artist Name = The Material Img capt = Img size = Background = group or band Origin = San Diego, California, U.S. Genre = Alternative rock Post punk Years active = 2005 Present URL = [http://myspace.com/thematerial The Material… … Wikipedia
Universal League for the Material Elevation of the Industrious Classes — The Universal League for the Material Elevation of the Industrious Classes was a 19th Century English political movement and organization.It was founded on 14 December 1863 by Marquis Townshend who was one of the few aristocrats to support the… … Wikipedia
Living in the Material World — Living in the Material World … Википедия
Living in the Material World — Infobox Album | Name = Living in the Material World Type = Album Artist = George Harrison Released = 22 June 1973 Recorded = October 1972 January 1973, except the backing track for Try Some Buy Some : February 1971 Genre = Rock Length = 43:55… … Wikipedia
Living in the Material World — Álbum de George Harrison Publicación 22 de junio de 1973 Grabación Octubre de 1972 Enero de 1973 excepto Try Some Buy Some : febrero de 1971 Género(s) … Wikipedia Español
Living in the Material World — Ne doit pas être confondu avec George Harrison: Living in the Material World. Living in the Material World Album par George Harrison Sortie 30 mai 1973 … Wikipédia en Français
Living In The Material World — Album par George Harrison Sortie 30 mai 1973 Enregistrement octobre 1972, janvier 1973 Studios Apple Durée 44:24 50:44 avec bonus … Wikipédia en Français
Living in the material world — Album par George Harrison Sortie 30 mai 1973 Enregistrement octobre 1972, janvier 1973 Studios Apple Durée 44:24 50:44 avec bonus … Wikipédia en Français
Spirits in the Material World — Infobox Single Name = Spirits in the Material World Artist = The Police from Album = Ghost in the Machine Released = 1981 Format = vinyl record (7 ) Recorded = 1981 Genre = New Wave Length = 2:58 Label = A M AMS 8194 Writer = Sting Producer =… … Wikipedia
Spirits in the material world — Saltar a navegación, búsqueda Spirits in the material world es la primera canción del álbum Ghost in the Machine grabado en 1981 por el grupo británico The Police. En la música están presentes, inusualmente para este grupo, un saxo y… … Wikipedia Español
Material Issue — Background information Origin Chicago Genres Power pop … Wikipedia