-
1 выдержка времени электрического реле
выдержка времени электрического реле
Интервал времени от момента подачи или съема возбуждения электрического реле до мгновения выполнения этим реле предназначенной функции, являющейся нормируемой характеристикой времени
[ ГОСТ 16022-83]EN
specified time
a time interval which is a specified characteristic of a specified-time relay
[IEV number 446-17-14]FR
temporisation
un des temps caractérisant une fonction d'un relais à temps spécifié
[IEV number 446-17-14]Тематики
EN
DE
FR
125. Выдержка времени электрического реле
D. Zeitverhalten
E. Specified time
F. Temporisation
Интервал времени от момента подачи или съема возбуждения электрического реле до мгновения выполнения этим реле предназначенной функции, являющейся нормируемой характеристикой времени
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > выдержка времени электрического реле
-
2 падение или повышение напряжения при заданном режиме нагрузки
падение или повышение напряжения при заданном режиме нагрузки
Разность между напряжением холостого хода обмотки и напряжением на ее выводах при заданных нагрузке и коэффициенте мощности при условии, что к другой (или к одной из других) обмотке(ок) подведено напряжение, равное:
- номинальному, если трансформатор включен на основное ответвление (в этом случае напряжение холостого хода рассматриваемой обмотки равно номинальному);
- напряжению другого ответвления, на которое включен трансформатор. Падение или повышение напряжения обычно выражают в процентах напряжения холостого хода рассматриваемой обмотки.
Примечание — В многообмоточном трансформаторе падение или повышение напряжения зависит от нагрузки и коэффициента мощности не только данной обмотки, но и других обмоток
(МЭС 421-07-03).
[ ГОСТ 30830-2002]EN
voltage drop or rise for a specified load condition
voltage regulation for a specified load condition
the arithmetic difference between the no-load voltage of a winding and the voltage developed at the terminals of the same winding at a specified load and power factor, the voltage supplied to (one of) the other winding(s) being equal to:
- its rated value if the transformer is connected on the principal tapping (the no-load voltage of the former winding is then equal to its rated value);
- the tapping voltage if the transformer is connected on another tapping.
This difference is generally expressed as a percentage of the no-load voltage of the former winding
NOTE – For multi-winding transformers, the voltage drop or rise depends not only on the load and power factor of the winding itself, but also on the load and power factor of the other windings
[IEV number 421-07-03]FR
hute ou augmentation de tension pour une condition de charge spécifiée
différence arithmétique entre la tension à vide d'un enroulement et la tension en charge aux bornes du même enroulement pour un courant de charge et un facteur de puissance spécifiés, la tension appliquée à l'autre (ou à l'un des autres) enroulement(s) étant égale:
- à sa valeur assignée, si le transformateur est connecté sur la prise principale (la tension à vide du premier enroulement étant alors égale à sa valeur assignée);
- à la tension de prise si le transformateur est connecté sur une autre prise.
Cette différence s'exprime généralement sous la forme d'un pourcentage de la tension à vide du premier enroulement
NOTE – Pour les transformateurs à plus de deux enroulements, la chute ou l'augmentation de tension dépend non seulement de la charge et du facteur de puissance de l'enroulement lui-même, mais aussi de la charge et du facteur de puissance des autres enroulements.
[IEV number 421-07-03]Тематики
Классификация
>>>EN
- voltage drop or rise for a specified load condition
- voltage regulation for a specified load condition
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > падение или повышение напряжения при заданном режиме нагрузки
-
3 время устойчивого замыкания (размыкания) контакта электрического реле
время устойчивого замыкания (размыкания) контакта электрического реле
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
[ ГОСТ 16022-83]EN
time to stable closed condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is closed and fulfils specified requirements
[IEV number 446-17-24]
time to stable open condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is open and fulfils specified requirements
[IEV number 446-17-25]FR
temps de fermeture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est fermé et répond aux prescriptions spécifiées
[IEV number 446-17-24]
temps d'ouverture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est ouvert et répond aux prescriptions spécifiées
[IEV number 446-17-25]
Тематики
EN
DE
FR
136. Время устойчивого замыкания (размыкания) контакта электрического реле
D. Ansprech-Rückfallzeit
Е. Time to stable closed (open) condition
F. Temps de fermeture (d’ouverture) stable
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > время устойчивого замыкания (размыкания) контакта электрического реле
-
4 действительное значение выдержки времени электрического реле
действительное значение выдержки времени электрического реле
Значение выдержки времени электрического реле, полученное в заданных условиях
[ ГОСТ 16022-83]EN
actual value of a specified time
the value of a time interval obtained under specified conditions
[IEV number 446-17-17]FR
valeur mesurée d'une temporisation
valeur d'une temporisation obtenue dans des conditions spécifiées
[IEV number 446-17-17]Тематики
EN
DE
FR
128. Действительное значение выдержки времени электрического реле
D. Istwert der Verzögerung
Е. Actual value of a specified time
F. Valeur mesurée d’une temporisation
Значение выдержки времени электрического реле, полученное в заданных условиях
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > действительное значение выдержки времени электрического реле
-
5 диапазон уставок выдержки времени электрического реле
диапазон уставок выдержки времени электрического реле
Совокупность значений уставок выдержки времени электрического реле
[ ГОСТ 16022-83]EN
setting range of a specified time
the range of the setting values of a specified time
[IEV number 446-17-18]FR
domaine d'ajustement d'une temporisation
ensemble des valeurs d'ajustement d'une temporisation
[IEV number 446-17-18]Тематики
Синонимы
EN
DE
FR
129. Диапазон уставок выдержки времени электрического реле
D. Einstellbereich der Virzögerung
E. Setting range of a specified time
F. Domaine d’ajustement d’une temporisation
Совокупность значений уставок выдержки времени электрического реле
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > диапазон уставок выдержки времени электрического реле
-
6 условный ток нерасцепления Int
- vereinbarter Nichtauslösestrom
- vereinbarte Nichtauslösestromstärke
- Nichtauslösestrom (eines Überlastauslösers)
условный ток нерасцепления Int
Установленное значение тока, который автоматический выключатель для электрооборудования способен проводить заданное (условное) время без расцепления.
[ ГОСТ Р 50031-99( МЭК 60934-93)]
условный ток нерасцепления (максимального реле или расцепителя тока)
Установленное значение тока, который реле или расцепитель способны проводить, не срабатывая, в течение заданного (условного) времени.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
conventional non-tripping current
a specified value of current which the circuit-breaker is capable of carrying for a specified time designated as conventional time, without tripping
[IEV number 442-05-54]
conventional non-tripping current (of an over-current release)
a specified value of current which the release can carry for a specified time (conventional time) without operating
[IEV number 441-17-22]FR
courant conventionnel de non-déclenchement
valeur spécifiée du courant que le disjoncteur peut supporter sans déclencher pendant un temps spécifié appelé temps conventionnel
[IEV number 442-05-54]
courant conventionnel de non-déclenchement (d'un déclencheur à maximum de courant)
valeur spécifiée de courant que peut supporter un déclencheur pendant une durée spécifiée (durée conventionnelle) sans fonctionner
[IEV number 441-17-22]Тематики
Синонимы
EN
DE
- Nichtauslösestrom (eines Überlastauslösers)
- vereinbarte Nichtauslösestromstärke
- vereinbarter Nichtauslösestrom
FR
Русско-немецкий словарь нормативно-технической терминологии > условный ток нерасцепления Int
-
7 электрическое реле с нормируемым временем
электрическое реле с нормируемым временем
Электрическое реле, у которого нормируется в отношении точности одно или несколько времен, характеризующих его
[ ГОСТ 16022-83]EN
specified-time relay
an electrical relay such that one or more of the times which characterize it (e.g. operate time) are subject to specified requirements, in particular concerning accuracy
[IEV number 446-11-04]FR
relais à temps spécifié
relais électrique dont un ou plusieurs des temps qui le caractérisent, par exemple le temps de fonctionnement, font l'objet de spécifications, en particulier en ce qui concerne la précision
[IEV number 446-11-04]Тематики
Синонимы
EN
DE
FR
4. Электрическое реле с нормируемым временем
D. Relais mit festgelegtem Zeitverhalten
E. Specified-time relay
F. Relais à temps spécifié
Электрическое реле, у которого нормируется в отношении точности одно или несколько времен, характеризующих его
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > электрическое реле с нормируемым временем
-
8 выключатель (контактный)
выключатель (контактный)
Контактный коммутационный аппарат, способный включать, проводить и отключать токи в нормальных условиях, в том числе при оговоренных рабочих перегрузках, а также в течение установленного времени проводить ток в оговоренных аномальных условиях, например при коротком замыкании.
МЭК 60050(441-14-10)
Примечание. Выключатель может быть способен включать, но не отключать ток короткого замыкания.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
(mechanical) switch
a mechanical switching device capable of making, carrying and breaking currents under normal circuit conditions which may include specified operating overload conditions and also carrying for a specified time currents under specified abnormal circuit conditions such as those of short circuit
NOTE – A switch may be capable of making but not breaking short-circuit currents.
[IEV number 441-14-10]FR
interrupteur (mécanique)
appareil mécanique de connexion capable d'établir, de supporter et d'interrompre des courants dans les conditions normales du circuit y compris éventuellement les conditions spécifiées de surcharge en service, ainsi que de supporter pendant une durée spécifiée des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit
NOTE – Un interrupteur peut être capable d'établir des courants de court-circuit mais n'est pas capable de les couper
[IEV number 441-14-10]Недопустимые, нерекомендуемые
Тематики
- выключатель, переключатель
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > выключатель (контактный)
-
9 измерительное электрическое реле с независимой выдержкой времени
измерительное электрическое реле с независимой выдержкой времени
Измерительное электрическое реле с нормируемым временем, выдержка времени которого практически не зависит от значения характеристической величины в заданных пределах изменения последней
[ ГОСТ 16022-83]EN
independent-time measuring relay
a specified-time measuring relay the specified time of which can be considered as being independent, within specified limits, of the value of the characteristic quantity
[IEV number 446-11-07]FR
relais de mesure à temps indépendant
relais de mesure à temps spécifié dont le temps spécifié peut être considéré comme indépendant de la valeur de la grandeur caractéristique entre les limites spécifiées de celle-ci
[IEV number 446-11-07]Тематики
EN
DE
FR
8. Измерительное электрическое реле с независимой выдержкой времени
D. Messrelais mit unabhängiger Zeitkennlinie
E. Independent-time measuring relay
F. Relais de mesure à temps indépendent
Измерительное электрическое реле с нормируемым временем, выдержка времени которого практически не зависит от значения характеристической величины в заданных пределах изменения последней
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > измерительное электрическое реле с независимой выдержкой времени
-
10 погружаемый
погружаемый
-
[IEV number 151-16-42]EN
submersible, adj
capable of operating even when immersed in a specified liquid under specified conditions
NOTE 1 – Specified conditions include depth or pressure.
NOTE 2 – An example of submersible device is a submarine cable.
[IEV number 151-16-42]FR
submersible, adj
capable de fonctionner même en immersion dans un liquide spécifié et dans des conditions spécifiées
NOTE 1 – Les conditions spécifiées comprennent la profondeur ou la pression.
NOTE 2 – Un exemple de dispositif submersible est un câble sous-marin.
[IEV number 151-16-42]EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > погружаемый
-
11 электрическое реле времени
электрическое реле времени
Логическое электрическое реле с нормируемой выдержкой времени
[ ГОСТ 16022-83]EN
time relay
specified-time relay (deprecated)
all-or-nothing relay with one or more specified time functions
[IEV number 445-01-01]FR
relais à temps spécifié, m
relais de tout ou rien comportant une ou plusieurs fonctions temporelles spécifiées
[IEV number 445-01-01]
Рис. Schneider ElectricПараллельные тексты EN-RU
A timing relay is a component which is designed to time events in industrial automation systems by closing or opening contacts before, during or after a set timing period.
[Schneider Electric]Реле времени - это устройства, предназначенные для применения в схемах промышленной автоматизации и в соответствии со своей функцией, реализующие заданные выдержки времени, и замыкающие или размыкающие контакты реле до, в процессе или после отсчета выдержки времени.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
Синонимы
EN
- automatic timer
- automatic timing device
- clock relay
- cycle timer
- delay relay
- delay switch
- preset interval timer
- specified-time relay
- time element
- time limit relay
- time relay
- time switch
- time-delay device
- time-delay relay
- time-delay switch
- timer
- timing device
- timing relay
- timing unit
DE
FR
D. Zeitrelais
E. Time relay
F. Relais temporisé
Логическое электрическое реле с нормируемой выдержкой времени
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > электрическое реле времени
-
12 электрическое реле с ненормируемым временем
электрическое реле с ненор мируемым временем
Электрическое реле, у которого время не нормируется в отношении точности
[ ГОСТ 16022-83]EN
non-specified-time relay
an electrical relay for which the times are not subject to any accuracy specification
[IEV number 446-11-05]FR
relais à temps non spécifié
relais électrique pour lequel aucun des temps ne fait l'objet de spécification relative à la précision
[IEV number 446-11-05]Тематики
Синонимы
EN
DE
FR
5. Электрическое реле с ненормируемым временем
D. Relais ohne festgelegten Zeitverhalten
E. Non-specified-time relay
F. Relais à temps non spécifié
Электрическое реле, у которого время не нормируется в отношении точности
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > электрическое реле с ненормируемым временем
-
13 автоматический выключатель
автоматический выключатель
Механический коммутационный аппарат1), способный включать, проводить и отключать токи при нормальном состоянии электрической цепи, а также включать, проводить в течение заданного времени и автоматически отключать токи в указанном аномальном состоянии электрической цепи, например, при коротком замыкании.
(МЭС 441-14-20)
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]
автоматический выключатель
-
[IEV number 442-05-01]EN
circuit breaker
a mechanical switching device, capable of making, carrying and breaking currents under normal circuit conditions and also making, carrying for a specified time and breaking currents under specified abnormal circuit conditions such as those of short circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
circuit breaker
A device designed to open and close a circuit by nonautomatic means and to open the circuit automatically on a predetermined overcurrent without damage to itself when properly applied within its rating.
NOTE The automatic opening means can be integral, direct acting with the circuit breaker, or remote from the circuit breaker.
Adjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker can be set to trip at various values of current, time, or both within a predetermined range. Instantaneous-trip (as applied to circuit breakers). A qualifying term indicating that no delay is purposely introduced in the tripping action of the circuit breaker.
Inverse-time (as applied to circuit breakers). A qualifying term indicating a delay is purposely introduced in the tripping action of the circuit breaker, which delay decreases as the magnitude of the current increases.
Nonadjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker does not have any adjustment to alter the value of current at which it will trip or the time required for its operation.
Setting (of a circuit breaker). The value of current, time, or both at which an adjustable circuit breaker is set to trip.
[National Electrical Cod]FR
disjoncteur
1) Должно быть контактный коммутационный аппарат
appareil mécanique de connexion capable d’établir, de supporter et d’interrompre des courants dans les conditions normales du circuit, ainsi que d’établir, de supporter pendant une durée spécifiée et d’in- terrompre des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
[Интент]КЛАССИФИКАЦИЯ
- По роду тока
- По напряжению
- По числу полюсов
- По виду корпуса
- По месту установки
- По изолирующей среде
- По установленным расцепителям
- По дополнительным защитам
- По назначению
- По категории применения
- По виду привода взвода пружины
- По выполняемой функции
-
По влиянию монтажного положения
Автоматические выключатели ABB Модульные автоматические выключатели
1. НЕКОТОРЫЕ СВЕДЕНИЯ ОБ АВТОМАТИЧЕСКИХ ВЫКЛЮЧАТЕЛЯХ Автоматический выключатель — это электрический аппарат, который автоматически отключает (и тем самым защищает) электрическую цепь при возникновении в ней аномального режима. Режим становится аномальным, когда в цепи начинает недопустимо изменяться (т. е. увеличиваться или уменьшаться относительно номинального значения) ток или напряжение.
Другими словами (более "инженерно") можно сказать, что автоматический выключатель защищает от токов короткого замыкания и токов перегрузки отходящую от него питающую линию, например, кабель и приемник(и) электрической энергии (осветительную сеть, розетки, электродвигатель и т. п.).
Как правило, автоматический выключатель может применятся также для нечастого (несколько раз в сутки) включения и отключения защищаемых электроприемников (защищаемой нагрузки).
[Интент]Выключатель предназначен для проведения тока в нормальном режиме и отключения тока при коротких замыканиях, перегрузках, недопустимых снижениях напряжения, а также до 30 оперативных включений и отключений электрических цепей в сутки и рассчитан для эксплуатации в электроустановках с номинальным рабочим напряжением до 660 В переменного тока частоты 50 и 60 Гц и до 440 В постоянного тока.
[Типовая фраза из российской технической документации] 2. ПРИНЦИП ДЕЙСТВИЯ Для защиты цепи от короткого замыкания применяется автоматический выключатель с электромагнитным расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Автоматический выключатель устроен таким образом, что сначала необходимо взвести пружину и только после этого его можно включить. У многих автоматических выключателей для взвода пружины необходимо перевести ручку вниз. После этого ручку переводят вверх. При этом замыкаются главные контакты.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Электромагнитный расцепитель;
5 - Сердечник
6 - Катушка
7 - Контактные зажимы автоматического выключателя
На рисунке показан один полюс автоматического выключателя во включенном положении: пружина 1 взведена, а главный контакт 2 замкнут.
Как только в защищаемой цепи возникнет короткое замыкание, ток, протекающий через соответствующий полюс автоматического выключателя, многократно возрастет. В катушке 6 сразу же возникнет сильное магнитное поле. Сердечник 5 втянется в катушку и освободит удерживающее устройство. Под действием пружины 1 главный контакт 2 разомкнется, в результате чего автоматический выключатель отключит и тем самым защитит цепь, в которой возникло короткое замыкание. Такое срабатывание автоматического выключателя происходит практически мгновенно (за сотые доли секунды).
Для защиты цепи от тока перегрузки применяют автоматические выключатели с тепловым расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Принцип действия такой же как и в первом случае, с той лишь разницей, что удерживающее устройство 3 освобождается под действием биметаллической пластины 5, которая изгибается от тепла, выделяемого нагревательным элементом 6. Количество тепла определяется током, протекающим через защищаемую цепь.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Тепловой расцепитель
5 - Биметаллическая пластина
6 - Нагревательный элемент
7 - Контактные зажимы автоматического выключателя
[Интент]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Обобщающие термины
Действия
- включение автоматического выключателя
- оперирование автоматического выключателя
- отключение автоматического выключателя
- срабатывание автоматического выключателя
EN
- auto-cutout
- automatic circuit breaker
- automatic cutout
- automatic switch
- breaker
- CB
- circuit breaker
- circuit-breaker
- cutout
DE
FR
Смотри также
Русско-немецкий словарь нормативно-технической терминологии > автоматический выключатель
14 влияющая (ий) величина фактор электрического реле
влияющая (ий) величина фактор электрического реле
Любая (ой) величина (фактор), способная (ый) изменить одну из заданных характеристик электрического реле.
Примечание. Заданными характеристиками являются, например, срабатывание, возврат, точность
[ ГОСТ 16022-83]EN
influencing quantity
any quantity likely to modify any of the specified characteristics of a relay (operating, releasing, accuracy, etc.)
[IEV number 446-14-01]
influencing factor
any factor likely to modify any of the specified characteristics of a relay (operating, releasing, accuracy, etc.)
[IEV number 446-14-02]FR
grandeur d'influence
grandeur susceptible de modifier l'une des caractéristiques spécifiées d'un relais: fonctionnement, relâchement, précision, et
[IEV number 446-14-01]
facteur d'influence
facteur susceptible de modifier l'une des caractéristiques spécifiées d'un relais: fonctionnement, relâchement, précision, etc
[IEV number 446-14-02]Тематики
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > влияющая (ий) величина фактор электрического реле
15 воздействующая величина электрического реле
воздействующая величина электрического реле
Электрическая величина, которая одна или в сочетании с другими электрическими величинами должна быть приложена к электрическому реле в заданных условиях для достижения ожидаемого функционирования
[ ГОСТ 16022-83]EN
energizing quantity
an electrical quantity (either current or voltage) which alone, or in combination with other such quantities, applied to a relay under specified conditions enables it to fulfil its purpose
[IEV number 446-12-01]
energizing quantity (for elementary relays)electrical quantity which, when applied to the input circuit of an elementary relay under specified conditions, enables it to fulfill its purpose
NOTE – For elementary relays the energizing quantity is usually a voltage. Therefore, the input voltage as energizing quantity is used in the definitions given below. Where a relay is energized by a given current instead, the respective terms and definitions apply with "current" used instead of "voltage".
[IEV number 444-03-01]FR
grandeur d'alimentation
grandeur électrique, courant ou tension, qui, seule ou en combinaison avec d'autres grandeurs électriques, courant ou tension, doit être appliquée dans des conditions spécifiées à un relais pour en obtenir le comportement attendu
[IEV number 446-12-01]
grandeur d'alimentation (pour les relais élémentaires), f
grandeur électrique qui, appliquée au circuit d'entrée d'un relais élémentaire dans des conditions spécifiées, lui permet d'accomplir sa fonction
NOTE – Pour les relais élémentaires, la grandeur d'alimentation est en général une tension. En conséquence, on utilise la tension d'entrée comme grandeur d'alimentation dans les définitions données ci-dessous. Lorsqu'un relais est alimenté par un courant, les termes et définitions respectifs sont à utiliser avec le terme "courant" au lieu du terme "tension".
[IEV number 444-03-01]Тематики
Классификация
>>>EN
DE
FR
49. Воздействующая величина электрического реле
D. Eingangsgrösse
Е. Energizing quantity
F. Grandeur d’alimentation
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > воздействующая величина электрического реле
16 время замыкания замыкающего контакта электрического реле
время замыкания замыкающего контакта электрического реле
Время от момента, когда входная воздействующая величина электрического реле, находящегося в начальном состоянии, принимает в заданных условиях определенное значение, до момента, когда замкнется в первый раз замыкающий контакт
[ ГОСТ 16022-83]EN
closing time of a make contact
for a relay which is in the release condition, the time interval between the instant a specified value of the input energizing quantity is applied under specified conditions and the instant when the make contact first closes
[IEV number 446-17-03]FR
temps d'établissement d'un contact de travail
pour un relais qui est dans un état de repos, temps écoulé entre l'instant où la grandeur d'alimentation d'entrée prend, dans des conditions spécifiées, une valeur définie et l'instant où s'établit pour la première fois le contact de travail
[IEV number 446-17-03]Тематики
EN
DE
FR
119. Время замыкания замыкающего контакта электрического реле
D. Ansprechzeit eines Schliessers
E. Closing time of a make contact
F. Temps d’etablissement d’un contact de travail
Время от момента, когда входная воздействующая величина электрического реле, находящегося в начальном состоянии, принимает в заданных условиях определенное значение, до момента, когда замкнется в первый раз замыкающий контакт
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > время замыкания замыкающего контакта электрического реле
17 время срабатывания электрического реле
время срабатывания электрического реле
Время от момента, когда входная воздействующая или характеристическая величина электрического реле, находящегося в начальном или исходном состоянии, принимает в заданных условиях определенное значение до момента, когда реле завершает срабатывание
[ ГОСТ 16022-83]EN
operate time
for a relay which is in the release condition (initial condition) the time interval between the instant a specified value of the input energizing quantity (characteristic quantity) is applied under specified condition and the instant when the relay switches
NOTE – This term is used only when the relay has output circuits of the same type and no precision is required according to contact time difference.
[IEV number 446-17-09]FR
temps de fonctionnement
temps d'action (terme déconseillé, utilisé pour les relais de tout ou rien)
pour un relais qui est dans l'état de repos ou dans un état initial, temps écoulé entre l'instant où la grandeur d'alimentation d'entrée ou la grandeur caractéristique prend, dans des conditions spécifiées, une valeur définie et l'instant où le relais commute
NOTE – Ce terme n'est utilisé que lorsque le relais ne comporte que des circuits de sortie de même nature et qu'aucune précision n'est nécessaire quant à la dispersion des temps de contact.
[IEV number 446-17-09]Тематики
EN
DE
FR
122. Время срабатывания электрического реле
D. Betätigungszeit
E. Operate time
F. Temps de fonctionnement;
Temps d’action (pour relais de tout ou rien)
Время от момента, когда входная воздействующая или характеристическая величина электрического реле, находящегося в начальном или исходном состоянии, принимает в заданных условиях определенное значение до момента, когда реле завершает срабатывание
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > время срабатывания электрического реле
18 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
19 значение величины срабатывания (возврата) электрического реле
значение величины срабатывания (возврата) электрического реле
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
[ ГОСТ 16022-83]EN
switching value
the value of the input energizing quantity (or characteristic quantity) at which a relay switches under specified conditions
NOTE – These specified conditions can be expressed by using one of the adjectives defined under the items 446-13-27 to 446-13-29.
[IEV number 446-13-24]FR
valeur de commutation
valeur de la grandeur d'alimentation d'entrée ou de la grandeur caractéristique, pour laquelle un relais commute dans des conditions spécifiées
NOTE – Ces conditions spécifiées peuvent être exprimées par l'un des qualificatifs définis de 446-13-27 à 446-13-29.
[IEV number 446-13-24]Тематики
Классификация
>>>EN
DE
FR
71. Значение величины срабатывания (возврата) электрического реле
D. Ansprechwert
Е. Operate value
F. Valeur de fonctionnement
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > значение величины срабатывания (возврата) электрического реле
20 измерительное электрическое реле с зависимой выдержкой времени
измерительное электрическое реле с зависимой выдержкой времени
Измерительное электрическое реле с нормируемым временем, выдержка времени которого заданным образом изменяется в зависимости от значения характеристической величины
[ ГОСТ 16022-83]EN
dependent-time measuring relay
a specified-time measuring relay for which times depend, in a specified manner, on the value of the characteristic quantity
[IEV number 446-11-06 ]FR
relais de mesure à temps dépendant
relais de mesure à temps spécifié dont les temps dépendent, de façon spécifiée, de la valeur de la grandeur caractéristique
[IEV number 446-11-06 ]Тематики
EN
DE
FR
7. Измерительное электрическое реле с зависимой выдержкой времени
D. Messrelais mit abhängiger Zeitkennlinie
E. Dependent-time measuring relay
F. Relais de mesure à temps dépendant
Измерительное электрическое реле с нормируемым временем, выдержка времени которого заданным образом изменяется в зависимости от значения характеристической величины
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > измерительное электрическое реле с зависимой выдержкой времени
См. также в других словарях:
specified — index aforesaid, certain (particular), certain (specific), conditional, express, stated Burton … Law dictionary
Specified — Specify Spec i*fy, v. t. [imp. & p. p. {Specified}; p. pr. & vb. n. {Specifying}.] [F. sp[ e]cifier, or OF. especifier, fr. LL. specificare. See {Species}, { fy}.] To mention or name, as a particular thing; to designate in words so as to… … The Collaborative International Dictionary of English
specified — adj. Specified is used with these nouns: ↑interval, ↑limit, ↑period … Collocations dictionary
specified — un·specified; … English syllables
specified — I ōlelo ia. ♦ At a specified time, i kekahi manawa i ōlelo ia … English-Hawaiian dictionary
specified — adjective clearly and explicitly stated (Freq. 6) meals are at specified times • Ant: ↑unspecified • Similar to: ↑mere, ↑nominative, ↑nominal, ↑specific … Useful english dictionary
specified employee — USA A key employee (as defined by Section 416(i) of the Internal Revenue Code (IRC)) of a publicly traded company. Specified employees are generally employees that satisfy any of the following conditions: • They own more than 5% of their employer … Law dictionary
specified transfer — England, Wales In the context of determining whether a deceased person s estate is an excepted estate for inheritance tax purposes, a specified transfer is: a gift of money, personal belongings, quoted shares or securities, an outright gift of… … Law dictionary
Specified requirements — need or expectation that is stated (p. 3.1 ISO/ IEC 17000:2004). Источник … Словарь-справочник терминов нормативно-технической документации
Specified Minimum Yield Strength — (SMYS) means the specified minimum yield strength for steel pipe manufactured in accordance with a listed specification. This is a common term used in the oil and gas industry for steel pipe used under the jurisdiction of the United States… … Wikipedia
specified exempt transfer — England, Wales In the context of determining whether a deceased person s estate is an excepted estate for inheritance tax purposes, specified exempt transfers are gifts made to: the deceased person s spouse or civil partner, charities, political… … Law dictionary
Перевод: с русского на немецкий
с немецкого на русский- С немецкого на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Персидский
- Французский