-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
2 заземление
заземление
Создание электрического соединения между данной точкой системы или установки, или оборудования и локальной землей.
Примечание.
Соединение с локальной землей может быть:
- преднамеренным или
- непреднамеренным, или случайным
и может быть постоянным или временным.
[ ГОСТ Р МЭК 60050-195-2005]
заземление
Электрическое соединение машин, аппаратов, приборов с землёй
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
заземление
Преднамеренное электрическое соединение какой-либо точки системы электроустановки или оборудования с заземляющим устройством.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]EN
earth (verb)
make an electric connection between a given point in a system or in an installation or in equipment and a local earth
NOTE – The connection to local earth may be
– intentional, or
– unintentional or accidental
and may be permanent or temporary.
Source: 604-04-01 MOD
[IEV number 195-01-08]FR
mettre à la terre (verbe)
réaliser une liaison électrique entre un point donné d'un réseau, d'une installation ou d'un matériel et une terre locale
NOTE – La liaison à la terre locale peut être:
– intentionnelle, ou
– non intentionnelle ou accidentelle
et peut être permanente ou temporaire.
Source: 604-04-01 MOD
[IEV number 195-01-08]Тематики
EN
DE
FR
50 заземление
Преднамеренное электрическое соединение какой-либо части электроустановки с заземляющим устройством
604-04-01
de Erden
en to earth (equipment, an installation or a system), to ground (USA)
fr mettre à la terre (un appareil, une installation ou un réseau)
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > заземление
-
3 заземлять
- erden, Verb
заземлять
Выполнять электрическое соединение между данной точкой системы или установки, или оборудования и локальной землей.
Примечание - Соединение с локальной землей может быть:
- преднамеренным;
- непреднамеренным или случайным;
- постоянным или временным.
[ ГОСТ Р МЭК 60050-826-2009]EN
earth, verb
ground (US), verb
make an electric connection between a given point in a system or in an installation or in equipment and local earth
NOTE – The connection to local earth may be:
– intentional, or
– unintentional or accidental
– and may be permanent or temporary.
Source: 195-01-08
[IEV number 826-13-03]FR
mettre à la terre, verbe
réaliser une liaison électrique entre un point donné d'un réseau, d'une installation ou d'un matériel et une terre locale
NOTE – La liaison à la terre locale peut être:
– intentionnelle, ou
– non intentionnelle ou accidentelle
– et peut être permanente ou temporaire.
Source: 195-01-08
[IEV number 826-13-03]Тематики
EN
DE
- erden, Verb
FR
- mettre à la terre, verbe
Русско-немецкий словарь нормативно-технической терминологии > заземлять
-
4 данные по выбросам
данные по выбросам
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
emission data
Data concerning pollutants released into the environment from a permanent or mobile installation or from products. (Source: AZENP)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > данные по выбросам
См. также в других словарях:
Installation art — uses sculptural materials and other media to modify the way a particular space is experienced. Installation art is not necessarily confined to gallery spaces and can be any material intervention in everyday public or private spaces.Installation… … Wikipedia
Permanent Change of Station — (PCS) is a U.S. military term referring to being permanently moved to a new post. (Similarly, a PCA is a permanent change of assignment, when the military member is reassigned to a new unit on the same post/installation.) Sometimes people use it… … Wikipedia
Permanent way — The permanent way means the physical elements of the railway line itself: generally the pairs of rails typically laid on sleepers embedded in ballast, intended to carry the ordinary trains of a railway. This page describes British practice and… … Wikipedia
installation — /in steuh lay sheuhn/, n. 1. something installed, as machinery or apparatus placed in position or connected for use. 2. the act of installing. 3. the fact of being installed. 4. Mil. any more or less permanent post, camp, station, base, or the… … Universalium
installation — in•stal•la•tion [[t]ˌɪn stəˈleɪ ʃən[/t]] n. 1) something installed, as machinery or apparatus placed in position or connected for use 2) the act of installing 3) the fact of being installed 4) mil any more or less permanent military post, camp,… … From formal English to slang
Contrôleur permanent d'isolement — Pour les articles homonymes, voir CPI. Un contrôleur permanent d isolement (CPI) est un appareil électrique souvent électronique permettant de détecter un défaut sur une installation de type IT. Ce dispositif est utilisé dans l industrie (par… … Wikipédia en Français
Controleur permanent d'isolement — Contrôleur permanent d isolement Un contrôleur permanent d isolement (CPI) est un appareil électrique souvent électronique permettant de détecter un défaut sur une installation de type IT. Ce dispositif est utilisé dans l industrie et dans les… … Wikipédia en Français
Disc Installation — Robert Irwin is associated with the Modern Art movement and is best known for his Installation art. Philosophers influence Irwin’s work, such as Maurice Merleau Ponty’s ideas of engagement and interaction between the physical world and people.… … Wikipedia
Secrétariat permanent pour la prévention des pollutions et des risques industriels — Un « Secrétariat permanent pour la prévention des pollutions et des risques industriels (S3PI ou SPPPI ou SPPPRI) est en France un groupe de divers partenaires, rassemblés par un ou plusieurs préfets, dont le travail vise à diminuer le… … Wikipédia en Français
Art and Art Exhibitions — ▪ 2009 Introduction Art The art market enjoyed an astonishing run of record breaking sales through the first nine months of a volatile 2008. In May Lucian Freud s Benefits Supervisor Sleeping (1995), a candid portrayal of a corpulent female … Universalium
Jean-Michel Othoniel — is a contemporary artist born in 1964 in Saint Etienne (France). He lives and works in Paris.Jean Michel Othoniel is an artist of Galerie Emmanuel Perrotin, Miami Paris Biography An artist who has a passion for all sorts of metamorphoses,… … Wikipedia
