-
1 устройство защиты от сверхтока (для устройства дифференциального тока)
устройство защиты от сверхтока (для устройства дифференциального тока)
-
[IEV number 442-05-13]EN
overcurrent protective device (for a residual current device)
a device, specified by the residual current device manufacturer, which has to be installed in the circuit in series with the residual current device in order to protect it against overcurrents
[IEV number 442-05-13]FR
dispositif de protection contre les surintensités (pour dispositif de coupure différentiel)
dispositif, spécifié par le constructeur du dispositif de coupure différentiel, qui doit être installé dans le circuit, en série avec le dispositif différentiel, en vue de sa protection contre les surintensités
[IEV number 442-05-13]Тематики
EN
DE
FR
- dispositif de protection contre les surintensités (pour dispositif de coupure différentiel)
Русско-немецкий словарь нормативно-технической терминологии > устройство защиты от сверхтока (для устройства дифференциального тока)
-
2 сверхток несрабатывания в главной цепи
сверхток несрабатывания в главной цепи
-
[IEV number 442-05-62]EN
non-operating overcurrent in the main circuit
Maximum value of current which can flow in the main circuit, in the absence of residual current, without causing operation of the detecting device of the residual current device as a consequence of asymmetry existing in the detecting device itself.
[IEV number 442-05-62]FR
surintensité de non-fonctionnement dans le circuit principal
Valeur maximale du courant pouvant circuler dans le circuit principal, en l'absence de courant différentiel résiduel, sans que le dispositif de détection du dispositif de coupure différentiel ne fonctionne en raison de la dissymétrie existant dans le dispositif de détection lui-même.
[IEV number 442-05-62]EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > сверхток несрабатывания в главной цепи
-
3 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
4 автоматический выключатель, управляемый дифференциальным током без встроенной защиты от сверхтока
автоматический выключатель, управляемый дифференциальным током без встроенной защиты от сверхтока
-
[IEV number 442-05-03]
Управляемый дифференциальным током автоматический выключатель, не предназначенный для защиты от сверхтока.EN
residual current operated circuit-breaker without integral overcurrent protection
RCCB (abbreviation)
a residual current operated switching device not designed to perform the functions of protection against overloads and/or short-circuits
[IEV number 442-05-03]
[IEC 61008-1, ed. 2.0 (1996-12)]FR
interrupteur différentiel sans protection incorporée contre les surintensités
ID (abréviation)
dispositif de coupure différentiel non conçu pour réaliser les fonctions de protection contre les surcharges et/ou les courts-circuits
[IEV number 442-05-03]
[IEC 61008-1, ed. 2.0 (1996-12)]Тематики
Обобщающие термины
Синонимы
EN
- pure residual current circuit-breaker
- RCCB
- residual current operated circuit-breaker without integral overcurrent protection
DE
FR
- ID
- interrupteur différentiel sans protection incorporée contre les surintensités
Русско-немецкий словарь нормативно-технической терминологии > автоматический выключатель, управляемый дифференциальным током без встроенной защиты от сверхтока
-
5 автоматический выключатель, управляемый дифференциальным током со встроенной защитой от сверхтока
автоматический выключатель, управляемый дифференциальным током со встроенной защитой от сверхтока
-
[IEV number 442-05-04*]
Управляемый дифференциальным током автоматический выключатель, предназначенный для выполнения функции защиты от сверхтока.EN
residual current operated circuit-breaker with integral overcurrent protection
RCBO (abbreviation)
a residual current operated switching device designed to perform the functions of protection against overloads and/or short-circuits
[IEV number 442-05-04]FR
disjoncteur différentiel résiduel avec protection incorporée contre les surintensités
DD (abréviation)
dispositif de coupure différentiel conçu pour réaliser les fonctions de protection contre les surcharges et/ou les courts-circuits
[IEV number 442-05-04]Тематики
Синонимы
EN
- RCBO (abbreviation)
- residual current operated circuit-breaker with integral overcurrent protection
DE
FR
- DD (abréviation)
- disjoncteur différentiel résiduel avec protection incorporée contre les surintensités
Русско-немецкий словарь нормативно-технической терминологии > автоматический выключатель, управляемый дифференциальным током со встроенной защитой от сверхтока
-
6 автоматический выключатель
автоматический выключатель
Механический коммутационный аппарат1), способный включать, проводить и отключать токи при нормальном состоянии электрической цепи, а также включать, проводить в течение заданного времени и автоматически отключать токи в указанном аномальном состоянии электрической цепи, например, при коротком замыкании.
(МЭС 441-14-20)
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]
автоматический выключатель
-
[IEV number 442-05-01]EN
circuit breaker
a mechanical switching device, capable of making, carrying and breaking currents under normal circuit conditions and also making, carrying for a specified time and breaking currents under specified abnormal circuit conditions such as those of short circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
circuit breaker
A device designed to open and close a circuit by nonautomatic means and to open the circuit automatically on a predetermined overcurrent without damage to itself when properly applied within its rating.
NOTE The automatic opening means can be integral, direct acting with the circuit breaker, or remote from the circuit breaker.
Adjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker can be set to trip at various values of current, time, or both within a predetermined range. Instantaneous-trip (as applied to circuit breakers). A qualifying term indicating that no delay is purposely introduced in the tripping action of the circuit breaker.
Inverse-time (as applied to circuit breakers). A qualifying term indicating a delay is purposely introduced in the tripping action of the circuit breaker, which delay decreases as the magnitude of the current increases.
Nonadjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker does not have any adjustment to alter the value of current at which it will trip or the time required for its operation.
Setting (of a circuit breaker). The value of current, time, or both at which an adjustable circuit breaker is set to trip.
[National Electrical Cod]FR
disjoncteur
1) Должно быть контактный коммутационный аппарат
appareil mécanique de connexion capable d’établir, de supporter et d’interrompre des courants dans les conditions normales du circuit, ainsi que d’établir, de supporter pendant une durée spécifiée et d’in- terrompre des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
[Интент]КЛАССИФИКАЦИЯ
- По роду тока
- По напряжению
- По числу полюсов
- По виду корпуса
- По месту установки
- По изолирующей среде
- По установленным расцепителям
- По дополнительным защитам
- По назначению
- По категории применения
- По виду привода взвода пружины
- По выполняемой функции
-
По влиянию монтажного положения
Автоматические выключатели ABB
Модульные автоматические выключатели
1. НЕКОТОРЫЕ СВЕДЕНИЯ ОБ АВТОМАТИЧЕСКИХ ВЫКЛЮЧАТЕЛЯХ Автоматический выключатель — это электрический аппарат, который автоматически отключает (и тем самым защищает) электрическую цепь при возникновении в ней аномального режима. Режим становится аномальным, когда в цепи начинает недопустимо изменяться (т. е. увеличиваться или уменьшаться относительно номинального значения) ток или напряжение.
Другими словами (более "инженерно") можно сказать, что автоматический выключатель защищает от токов короткого замыкания и токов перегрузки отходящую от него питающую линию, например, кабель и приемник(и) электрической энергии (осветительную сеть, розетки, электродвигатель и т. п.).
Как правило, автоматический выключатель может применятся также для нечастого (несколько раз в сутки) включения и отключения защищаемых электроприемников (защищаемой нагрузки).
[Интент]Выключатель предназначен для проведения тока в нормальном режиме и отключения тока при коротких замыканиях, перегрузках, недопустимых снижениях напряжения, а также до 30 оперативных включений и отключений электрических цепей в сутки и рассчитан для эксплуатации в электроустановках с номинальным рабочим напряжением до 660 В переменного тока частоты 50 и 60 Гц и до 440 В постоянного тока.
[Типовая фраза из российской технической документации] 2. ПРИНЦИП ДЕЙСТВИЯ Для защиты цепи от короткого замыкания применяется автоматический выключатель с электромагнитным расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Автоматический выключатель устроен таким образом, что сначала необходимо взвести пружину и только после этого его можно включить. У многих автоматических выключателей для взвода пружины необходимо перевести ручку вниз. После этого ручку переводят вверх. При этом замыкаются главные контакты.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Электромагнитный расцепитель;
5 - Сердечник
6 - Катушка
7 - Контактные зажимы автоматического выключателя
На рисунке показан один полюс автоматического выключателя во включенном положении: пружина 1 взведена, а главный контакт 2 замкнут.
Как только в защищаемой цепи возникнет короткое замыкание, ток, протекающий через соответствующий полюс автоматического выключателя, многократно возрастет. В катушке 6 сразу же возникнет сильное магнитное поле. Сердечник 5 втянется в катушку и освободит удерживающее устройство. Под действием пружины 1 главный контакт 2 разомкнется, в результате чего автоматический выключатель отключит и тем самым защитит цепь, в которой возникло короткое замыкание. Такое срабатывание автоматического выключателя происходит практически мгновенно (за сотые доли секунды).
Для защиты цепи от тока перегрузки применяют автоматические выключатели с тепловым расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Принцип действия такой же как и в первом случае, с той лишь разницей, что удерживающее устройство 3 освобождается под действием биметаллической пластины 5, которая изгибается от тепла, выделяемого нагревательным элементом 6. Количество тепла определяется током, протекающим через защищаемую цепь.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Тепловой расцепитель
5 - Биметаллическая пластина
6 - Нагревательный элемент
7 - Контактные зажимы автоматического выключателя
[Интент]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Обобщающие термины
Действия
- включение автоматического выключателя
- оперирование автоматического выключателя
- отключение автоматического выключателя
- срабатывание автоматического выключателя
EN
- auto-cutout
- automatic circuit breaker
- automatic cutout
- automatic switch
- breaker
- CB
- circuit breaker
- circuit-breaker
- cutout
DE
FR
Смотри также
Русско-немецкий словарь нормативно-технической терминологии > автоматический выключатель
7 ожидаемый ток
ожидаемый ток
Ток, который будет в цепи, если коммутационный аппарат зашунтироватъ проводником с пренебрежимо малым сопротивлением.
[ ГОСТ 17703-72]EN
prospective current
the current that would flow in the circuit, if each main current path of the switching device and of the overcurrent protective device, if any, were replaced by a conductor of negligible impedance
NOTE – The prospective current can be qualified in the same manner as an actual current, for example: prospective breaking current, prospective peak current, prospective residual current, etc.
[IEV number 442-01-47]FR
courant présumé
courant qui circulerait dans le circuit, si chaque voie principale de courant du dispositif de coupure et du dispositif éventuel de protection contre les surintensités était remplacée par un conducteur d'impédance négligeable
NOTE – Le courant présumé peut être qualifié de la même façon qu'un courant réel, par exemple courant de coupure présumé, courant de crête présumé, courant différentiel présumé, etc.
[IEV number 442-01-47]Тематики
- аппарат, изделие, устройство...
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > ожидаемый ток
8 максимальный расцепитель тока косвенного действия
максимальный расцепитель тока косвенного действия
Максимальный расцепитель тока, питаемые током в главной цепи коммутационного аппарата через трансформатор тока или шунт.
[Интент]EN
indirect over-current release
an over-current release energized by the current in the main circuit of a mechanical switching device through a current transformer or a shunt.
[IEV number 441-16-37]
[IEC 62271-100, ed. 2.0 (2008-04)]FR
déclencheur indirect à maximum de courant
déclencheur à maximum de courant alimenté par le courant dans le circuit principal d’un appareil mécanique de connexion par I’intermédiaire d’un transformateur de courant ou d’un shunt.
[IEV number 441-16-37]
[IEC 62271-100, ed. 2.0 (2008-04)]
Недопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > максимальный расцепитель тока косвенного действия
9 максимальный расцепитель тока прямого действия
максимальный расцепитель тока прямого действия
Максимальный расцепитель тока, срабатывающий непосредственно от тока главной цепи коммутационного аппарата.
[Интент]EN
direct over-current release
an over-current release directly energized by the current in the main circuit of a mechanical switching device.
[IEV number 441-16-36]
[IEC 62271-100, ed. 2.0 (2008-04)]FR
déclencheur direct à maximum de courant
déclencheur à maximum de courant alimenté directement par le courant dans le circuit principal d’un appareil mécanique de connexion.
[IEV number 441-16-36]
[IEC 62271-100, ed. 2.0 (2008-04)]
Недопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > максимальный расцепитель тока прямого действия
10 селективность по сверхтокам
селективность по сверхтокам
Координация рабочих характеристик двух или нескольких устройств для защиты от сверхтоков с таким расчетом, чтобы в случае возникновения сверхтоков в пределах указанного диапазона срабатывало только устройство, предназначенное для оперирования в данном диапазоне, а прочие не срабатывали.
Примечание. Различаются последовательная селективность, когда через различные устройства для защиты от сверхтоков проходит практически одинаковый сверхток, и параллельная селективность, когда через тождественные защитные устройства проходят различные доли сверхтока.
МЭК 60050(441-17-15).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
селективность при сверхтоке
Координация соответствующих характеристик двух или более устройств для защиты от сверхтоков с таким расчетом, чтобы при появлении сверхтоков в установленных пределах срабатывало устройство, рассчитанное на эти пределы, в то время как другое (ие) устройство (а) не срабатывало (и).
[ ГОСТ Р 50339. 0-2003 ( МЭК 60269-1-98)]
селективность при сверхтоке предохранителей
Координация соответствующих характеристик двух или нескольких предохранителей, или предохранителей и других защитных устройств, обеспечивающая при появлении сверхтоков, находящихся в данных пределах, состояние срабатывания предохранителя, предусмотренного для срабатывания в этих пределах, тогда как другие предохранители не срабатывают.
[ ГОСТ 17242-86]EN
over-current discrimination
co-ordination of the operating characteristics of two or more over-current protective devices such that, on the incidence of over-currents within stated limits, the device intended to operate within these limits does so, while the other(s) does (do) not
NOTE Distinction is made between series discrimination involving different over-current protective devices passing substantially the same over-current and network discrimination involving identical protective devices passing different proportions of the over-current.
[IEV 441-17-15]FR
sélectivité lors d'une surintensité
coordination entre les caractéristiques de fonctionnement de plusieurs dispositifs de protection à maximum de courant de telle façon qu'à l'apparition de surintensités comprises dans des limites données, le dispositif prévu pour fonctionner entre ces limites fonctionne, tandis que le ou les autres ne fonctionnent pas
NOTE On distingue la sélectivité série réalisée par différents dispositifs de protection à maximum de courant soumis pratiquement à la même surintensité et la sélectivité de réseau réalisée par des dispositifs de protection à maximum de courant identiques soumis à des fractions différentes de la surintensité
[IEV 441-17-15]Параллельные тексты EN-RU
Discrimination Method
Appropriate when downstream CB is capable of 100% fault current break within the entire range of protection.
[LS Industrial Systems]Селективность по сверхтокам
Данный метод применяется в том случае, когда автоматический выключатель, расположенный со стороны нагрузки, может в течение времени срабатывания выдержать 100 % тока короткого замыкания.
[Перевод Интент]Тематики
- выключатель автоматический
- предохранитель
- электротехника, основные понятия
- электроустановки
EN
- current discrimination
- discrimination method
- over-current discrimination
- overcurrent discrimination
- selectivity
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > селективность по сверхтокам
См. также в других словарях:
Residual-current device — A two pole residual current device A Residual Current Device is a generic term covering both RCCBs and RCBOs. A Residual Current Circuit Breaker (RCCB) is an electrical wiring device that disconnects a circuit whenever it detects that the… … Wikipedia
ANSI Device Numbers — The ANSI Standard Device Numbers [ [http://www.geindustrial.com/pm/notes/ref/ANSI.pdf GE Multilin ANSI Standard Device Number] ] [ Protective Relaying Manual , Pennsylvania Electric Association (1975)] [ [http://www.basler.com/downloads/ANSI… … Wikipedia
Residual Current protective Device — Fehlerstromschutzschalter geöffneter Fehlerstromschutzschalter … Deutsch Wikipedia
Fuse (electrical) — A miniature time delay fuse used to protect electronic equipment, rated 0.3 amperes at 250 volts. 1.25 inches (about 32 mm) long … Wikipedia
Appliance classes — In the electrical appliance manufacturing industry, the following IEC protection classes are used to differentiate between the protective earth connection requirements of devices. Contents 1 Class 0 1.1 Class 01 2 Class I 3 … Wikipedia
Protective relay — See also: Power system protection In electrical engineering, a protective relay is a complex electromechanical apparatus, often with more than one coil, designed to calculate operating conditions on an electrical circuit and trip circuit breakers … Wikipedia
ГОСТ Р 50345-2010: Аппаратура малогабаритная электрическая. Автоматические выключатели для защиты от сверхтоков бытового и аналогичного назначения. Часть 1. Автоматические выключатели для переменного тока — Терминология ГОСТ Р 50345 2010: Аппаратура малогабаритная электрическая. Автоматические выключатели для защиты от сверхтоков бытового и аналогичного назначения. Часть 1. Автоматические выключатели для переменного тока оригинал документа: 3.5.12… … Словарь-справочник терминов нормативно-технической документации
ГОСТ Р МЭК 60050-826-2009: Установки электрические. Термины и определения — Терминология ГОСТ Р МЭК 60050 826 2009: Установки электрические. Термины и определения оригинал документа: ( длительный ) допустимый ток ((continuous) current carrying capacity ampacity (US)): Максимальное значение электрического тока, который… … Словарь-справочник терминов нормативно-технической документации
Digital protective relay — In electrical engineering of power systems, a digital protective relay uses a microcontroller with software based protection algorithms for the detection of electrical faults. Such relays are also termed as microprocessor type protective relays.… … Wikipedia
ГОСТ Р МЭК 60755-2012: Общие требования к защитным устройствам, управляемым дифференциальным (остаточным) током — Терминология ГОСТ Р МЭК 60755 2012: Общие требования к защитным устройствам, управляемым дифференциальным (остаточным) током оригинал документа: 3.4.10 I2t (интеграл Джоуля) (Joule integral): Интеграл квадрата силы тока поданному интервалу… … Словарь-справочник терминов нормативно-технической документации
Earthing system — In sulvent systems, an earthing system defines the electrical potential of the conductors relative to that of the Earth s conductive surface. The choice of earthing system has implications for the safety and electromagnetic compatibility of the… … Wikipedia
Перевод: с русского на немецкий
с немецкого на русский- С немецкого на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский