-
1 входное полное сопротивление
входное полное сопротивление
-
[IEV number 312-06-18]EN
input impedance
impedance of the input circuit measured between the input terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the input circuit is such that the instantaneous value of the current flowing into the input terminals is a non-linear function of the instantaneous value of the input voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual input circuit, is sometimes called the "equivalent input impedance".
[IEV number 312-06-18]FR
impédance du circuit d'entrée
impédance du circuit d'entrée entre les bornes d'entrée dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit d'entrée est tel que la valeur instantanée du courant traversant les bornes d'entrée est une fonction non linéaire de la valeur instantanée de la tension d'entrée dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit d'entrée réel, est parfois appelée "impédance équivalente d'entrée".
[IEV number 312-06-18]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > входное полное сопротивление
-
2 выходное полное сопротивление
выходное полное сопротивление
-
[IEV number 312-06-19]EN
output impedance
impedance of the output circuit measured between the output terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the output circuit is such that the instantaneous value of the current flowing into the output terminals is a non-linear function of the instantaneous value of the output voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual output circuit, is sometimes called the "equivalent output impedance".
[IEV number 312-06-19]FR
impédance du circuit de sortie
impédance du circuit de sortie entre les bornes de sortie dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit de sortie est tel que la valeur instantanée du courant traversant les bornes de sortie est une fonction non linéaire de la valeur instantanée de la tension de sortie dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit de sortie réel, est parfois appelée "impédance équivalente de sortie".
[IEV number 312-06-19]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > выходное полное сопротивление
-
3 затекание припоя в зазор
затекание припоя в зазор
затекание
Заполнение расплавленным припоем паяльного зазора.
[ ГОСТ 17325-79]Тематики
- сварка, резка, пайка
Синонимы
EN
DE
Затекание
D. Fließen
E. Flowing
Заполнение расплавленным припоем паяльного зазора
Источник: ГОСТ 17325-79: Пайка и лужение. Основные термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > затекание припоя в зазор
-
4 потоки воды
потоки воды
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
flowing water
Moving waters like rivers and streams. (Source: LANDY)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > потоки воды
-
5 фонтанирующая скважина
adj1) geol. Eruptiersonde, Eruptivsonde, Springer, Springerquelle, Springquelle, Sprudelbohrung2) eng. Eruptionsbohrung, eruptierendes Bohrloch3) oil. Eruptivfördersonde, eruptierende Sonde, flowing-wellУниверсальный русско-немецкий словарь > фонтанирующая скважина
-
6 фонтанная скважина
-
7 атмосферная инверсия
атмосферная инверсия
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
atmospheric inversion
A temperature inversion in the atmosphere in which the temperature, instead of falling, increases with height above the ground. With the colder and heavier air below, there is no tendency to form upward currents and turbulence is suppressed. Inversions are often formed in the late afternoon when the radiation emitted from the ground exceeds that received from the sinking sun. Inversions are also caused by katabatic winds, that is cold winds flowing down the hillside into a valley, and by anticyclones. In inversion layers, both vertical and horizontal diffusion is inhibited and pollutants become trapped, sometimes for long periods. Low-level discharges of pollutants are more readily trapped by inversions than high level dischargers, hence the case for high stacks. Furthermore, high level discharges into an inversion tend to remain at a high level because of the absence of vertical mixing. (Source: GILP96)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > атмосферная инверсия
-
8 водная эрозия
водная эрозия
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
water erosion
The breakdown of solid rock into smaller particles and its removal by water. As weathering, erosion is a natural geological process, but more rapid soil erosion results from poor land-use practices, leading to the loss of fertile topsoil and to the silting of dams, lakes, rivers and harbours. There are three classes of erosion by water. a) Splash erosion occurs when raindrops strike bare soil, causing it to splash, as mud, to flow into spaces in the soil and to turn the upper layer of soil into a structureless, compacted mass that dries with a hard, largely impermeable crust. b) Surface flow occurs when soil is removed with surface run-off during heavy rain. c) Channelized flow occurs when a flowing mixture of water and soil cuts a channel, which is then deepened by further scouring. A minor erosion channel is called a rill, a larger channel a gully. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > водная эрозия
-
9 дифференциальный ток
дифференциальный ток
Алгебраическая сумма значений электрических токов во всех токоведущих проводниках в одно и то же время в данной точке электрической цепи электрической установки
[ ГОСТ Р МЭК 60050-826-2009]
Примечание - Определение термина «дифференциальный ток» в МЭК 60050-826 [4] сформулировано для электрической цепи. Через главную цепь устройства дифференциального тока, защищающего электрическую цепь, проходят все ее проводники, находящиеся под напряжением, вследствие чего дифференциальный ток, появляющийся в электрической цепи, будет равен дифференциальному току, определяемому устройством дифференциального тока.
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
дифференциальный ток
IΔ,
Действующее значение векторной суммы токов, протекающих в главной цепи.
дифференциальный ток
ID
Среднеквадратическое значение векторной суммы токов, протекающих через главную цепь устройства дифференциального тока.
П р и м е ч а н и е - Определение термина «дифференциальный ток» в МЭК 60050-442 [6] сформулировано для устройства дифференциального тока.
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
дифференциальный ток
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]EN
residual current
algebraic sum of the values of the electric currents in all live conductors, at the same time at a given point of an electric circuit in an electrical installation
[IEV number 826-11-19]
residual current
r.m.s. value of the vector sum of the currents flowing through the main circuit of the residual current device
[IEV number 442-05-19]FR
courant différentiel résiduel, m
somme algébrique des valeurs des courants électriques dans tous les conducteurs actifs, au même instant en un point donné d'un circuit électrique d'une installation électrique
[IEV number 826-11-19]
courant différentiel résiduel
valeur efficace de la somme vectorielle des courants circulant dans le circuit principal du dispositif de coupure différentiel
[IEV number 442-05-19]Недопустимые, нерекомендуемые
Тематики
- электробезопасность
- электротехника, основные понятия
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > дифференциальный ток
-
10 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
11 жидкие отходы после обработки
жидкие отходы после обработки
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
waste treatment effluent
Partially or completely treated water or waste water flowing out of a waste treatment plant. (Source: DEE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > жидкие отходы после обработки
-
12 защита от тока утечки на корпус
- Kessel-Erdschlussschutz, m
- Gestell-Erdschlussschutz, m
защита от тока утечки на корпус
Защита, входной воздействующей величиной которой является ток, протекающий через соединение, связывающее корпус установки с землей.
Пример: защита трансформатора от тока утечки на бак.
[Разработка типовых структурных схем микропроцессорных устройств РЗА на объектах ОАО "ФКС ЕЭС". Пояснительная записка. Новосибирск 2006 г.]EN
frame leakage protection
case ground protection (US)
frame ground protection (US)
protection in which the input energizing quantity is a current flowing through the path connecting the framework of the stated equipment in the protected section to earth
Example: A frame leakage protection of a transformer tank.
[ IEV ref 448-14-21]FR
protection de masse
protection dont la grandeur d'alimentation est un courant circulant dans la connexion reliant à la terre la structure du matériel considéré, dans la section protégée
Exemple: Protection de masse d'une cuve de transformateur.
[ IEV ref 448-14-21]Тематики
EN
DE
- Gestell-Erdschlussschutz, m
- Kessel-Erdschlussschutz, m
FR
Русско-немецкий словарь нормативно-технической терминологии > защита от тока утечки на корпус
-
13 номинальный ток Iном
- Bemessungsstrom (einer Wicklung eines Transformators oder einer Drosselspule)
номинальный ток Iном
Ток, протекающий через линейный вывод обмотки и определяемый номинальной мощностью Sном, В·А, и номинальным напряжением Uном, В, обмотки
(МЭС 421-04-05).
Примечания
1 Для трехфазной обмотки номинальный ток Iном, А, определяют по формуле
Iном = Sном / √3Uном
2 Для однофазных трансформаторов, предназначенных для соединения в трехфазную группу, номинальный ток обмотки, соединяемой в треугольник, определяют как линейный ток Iл, А, по формуле
Iном = Iл / √3EN
rated current (of a winding of a transformer or shunt reactor)
the current, flowing through a line terminal of a winding, derived by dividing the rated power of the winding by the rated voltage of the winding and by an appropriate phase factor
[IEV number 421-04-05]FR
courant assigné (d'un enroulement de transformateur ou d'une bobine d'inductance shunt)
courant arrivant à une borne de ligne d'un enroulement, obtenu en divisant la puissance assignée de l'enroulement par la tension assignée de cet enroulement et par un facteur de phase approprié
[IEV number 421-04-05]Тематики
Классификация
>>>EN
DE
- Bemessungsstrom (einer Wicklung eines Transformators oder einer Drosselspule)
FR
- courant assigné (d'un enroulement de transformateur ou d'une bobine d'inductance shunt)
Русско-немецкий словарь нормативно-технической терминологии > номинальный ток Iном
-
14 оплавление покрытия
37. Оплавление покрытия
D. Abschmelzen des Oberzugs
E. Coating partial melting
F. Ficrion particlle de revetement
Нагрев покрытия до температуры, превышающей температуру его плавления
Источник: ГОСТ 9.008-73: ЕСЗКС. Покрытия металлические и неметаллические неорганические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > оплавление покрытия
-
15 отключение (для устройства дифференциального тока)
прерывание
-
[IEV number 442-05-26]EN
interruption (for a residual current device)
function consisting in bringing automatically the main contacts of the residual current device from the closed position into the open position, thereby interrupting the current(s) flowing through them
[IEV number 442-05-26]FR
coupure (pour un dispositif de coupure différentiel)
fonction consistant à amener automatiquement les contacts principaux du dispositif de coupure différentiel de la position fermée à la position ouverte, interrompant ainsi le (les) courant(s) qui les traversent
[IEV number 442-05-26]Тематики
- аппарат, изделие, устройство...
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > отключение (для устройства дифференциального тока)
-
16 паводковый сток
паводковый сток
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
flood runoff
The total quantity of water flowing from the catchment during the period of the flood. (Source: ECHO2)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > паводковый сток
-
17 приток воды
приток воды
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
inflow
1) Water other than wastewater that enters a sewer system (including sewer service connections) from sources such as, but not limited to, roof leaders, cellars drains, yard drains, area drains, drains from springs and swampy areas, manhole covers, cross connections between storm sewers and sanitary sewers, catch basins, cooling towers, storm waters, surface runoff, street wash waters, or drainage. Inflow does not include, and is distinguished from, infiltration. 2) Action of flowing in; an inflow of effluent into a river. (Source: JJK / PHC)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > приток воды
-
18 реологические свойства горной породы
реологические свойства горной породы
Механические свойства, отражающие влияние длительного воздействия нагрузок на изменение напряженно-деформированного состояния горных пород.
[ ГОСТ Р 50544-93]Тематики
Обобщающие термины
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > реологические свойства горной породы
-
19 тепловое реле
тепловое реле
-
[Интент]
электротепловое реле
Электрическое реле, работа которого основана на тепловом действии электрического тока
[ ГОСТ 16022-83]EN
thermal electrical relay
dependent-time measuring relay which is intended to protect an equipment from electrical thermal damage by the measurement of the current flowing in the protected equipment and by a characteristic curve simulating its thermal behaviour
[IEC 62271-1, ed. 1.0 (2007-10)]FR
relais électrique thermique
relais de mesure à temps dépendant destiné à protéger un équipement contre les dommages thermiques d'origine électrique par la mesure du courant circulant dans l'équipement protégé et par une courbe caractéristique simulant son comportement thermique
[IEC 62271-1, ed. 1.0 (2007-10)]Параллельные тексты EN-RU
Meanwhile, EMPR (Electronic Motor Protection Relay), also called as ‘Electronic Overcurrent Relay’ or ‘Electronic Overload Relay) may replace TOR to protect a low voltage motor.
[LS Industrial Systems]При этом, для зашиты низковольтного электродвигателя, тепловое реле (TOR) можно заменить на электронное реле защиты электродвигателя (EMPR), которое также называют "электронное реле защиты от сверхтока" или электронное реле защиты от перегрузки.
[Перевод Интент]It is better to use a fan with thermal switches.
In this case the positioning of the fans should be taken care so as to not place the fan’s thermal switch close to heat dissipating devices so as to avoid any malfunctioning of thermal switch.
[Schneider Electric]
Лучше использовать вентиляторы с тепловым реле.
В этом случае вентиляторы следует разместить таким образом, чтобы рядом с тепловым реле не было аппаратов с сильным выделением тепла. Это позволит избежать неправильного срабатывания теплового реле.
[Перевод Интент]Тематики
- расцепитель, тепловое реле
- реле электрическое
EN
- thermal electrical relay
- thermal overload relay
- thermal protection
- thermal relay
- thermal switch
- thermoswitch
- TOR
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > тепловое реле
-
20 ток замыкания на землю
ток замыкания на землю
Ток повреждения, проходящий в землю через место замыкания.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
ток замыкания на землю
Электрический ток, протекающий в Землю, открытую и стороннюю проводящие части и защитный проводник при повреждении изоляции токоведущей части.
Примечание – В Международном электротехническом словаре используют термин «ток повреждения на землю».
При повреждении изоляции токоведущей части резко уменьшается сопротивление между этой токоведущей частью, с одной стороны, и Землёй, открытыми, сторонними проводящими частями и защитными проводниками, с другой стороны. В результате этого резко увеличивается величина электрического тока, стекающего с токоведущей части в Землю, а также в проводящие части, соединённые защитными проводниками с заземляющим устройством электроустановки здания и с заземлённой токоведущей частью источника питания. Подобный электрический ток аварийного режима электроустановки здания в нормативной и правовой документации называют током замыкания на землю.
Путь, по которому может протекать ток замыкания на землю, зависит от типа заземления системы. Если произошло повреждение основной изоляции опасной токоведущей части электрооборудования класса I и возникло её замыкание на открытую проводящую часть, то в электроустановке здания, соответствующей типам заземления системы TT и IT, ток замыкания на землю через повреждённую изоляцию протекает из токоведущей части в открытую проводящую часть. Далее из открытой проводящей части по защитному проводнику, главной заземляющей шине, заземляющим проводникам и заземлителю электрический ток протекает в локальную землю. Если электроустановка здания соответствует типам заземления системы TN, преобладающая часть тока замыкания на землю протекает не в локальную землю, а по защитным проводникам и по PEN-проводникам электроустановки здания и низковольтной распределительной электрической сети протекает к заземлённой токоведущей части источника питания.
[] http://www.volt-m.ru/glossary/letter/%D2/view/81/EN
earth fault current
current flowing to earth due to an insulation fault
[IEV number 442-01-23]FR
courant de défaut à la terre
courant qui s'écoule à la terre lors d'un défaut d'isolement
[IEV number 442-01-23]Параллельные тексты EN-RU The earth fault current starts as a localized arc at the point where the insulation has failed; this arc is characterized by a rather modest current level of the order of tens of milliamps. Subsequently, the fault evolves, more or less rapidly, to become a true earth-phase fault. If not rapidly interrupted by protection devices, this fault may end up affecting all the phases, creating a three-phase shortcircuit with earth contact.
[ABB]Ток замыкания на землю возникает в зоне повреждения изоляции в виде локальной дуги. Эта дуга характеризуется относительно небольшим значением тока порядка десятков миллиампер. Со временем зона повреждения изоляции постепенно увеличивается, и образуется однофазное замыкание на землю. Если ток не будет своевременно отключен устройством защиты, то эта неисправность в итоге может затронуть все фазные проводники и привести к трехфазному короткому замыканию на землю.
[Перевод Интент]Therefore, the first consequence of the earth fault current is the damage caused to the plant, whether due to the modest initial arc currents which, because of the difficulty in detection by the overcurrent releases may continue for long periods of time and start a fire, or due to the shortcircuit that develops after the integrity of the entire plant has been jeopardized.
[ABB]Таким образом, ток замыкания на землю может повредить электроустановку. Сначала возникает электрическая дуга с небольшим током, который максимальный расцепитель тока обнаружить не в состоянии, вследствие чего этот ток может протекать длительное время и привести к пожару. Кроме того, может возникнуть короткое замыкание, способное полностью вывести электроустановку из строя.
[Перевод Интент]Another important consequence of the earth fault current involves the danger to persons caused by indirect contact, i.e. following the contact with exposed-conductive-parts that have been energized accidentally due to a decay in the insulation.
[ABB]Другим последствием тока замыкания на землю является опасность косвенного прикосновения, т. е. прикосновения человека к открытым проводящим частям, оказавшимся вследствие повреждения изоляции под напряжением.
[Перевод Интент]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > ток замыкания на землю
- 1
- 2
См. также в других словарях:
Flowing — Flow ing, a. That flows or for flowing (in various sense of the verb); gliding along smoothly; copious. [1913 Webster] {Flowing battery} (Elec.), a battery which is kept constant by the flowing of the exciting liquid through the cell or cells.… … The Collaborative International Dictionary of English
Flowing — Flow ing, a. & n. from {Flow}, v. i. & t. [1913 Webster] … The Collaborative International Dictionary of English
flowing — index circulation, copious, eloquent, facile, fluvial, full Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
flowing — [adj] gushing, abounding brimming, continuous, cursive, easy, falling, flooded, fluent, fluid, fluidic, full, issuing, liquefied, liquid, overrun, pouring out, prolific, rich, rippling, rolling, running, rushing, sinuous, smooth, spouting,… … New thesaurus
Flowing — Flow Flow (fl[=o]), v. i. [imp. & p. p. {Flowed} (fl[=o]d); p. pr. & vb. n. {Flowing}.] [AS. fl[=o]wan; akin to D. vloeijen, OHG. flawen to wash, Icel. fl[=o]a to deluge, Gr. plw ein to float, sail, and prob. ultimately to E. float, fleet.… … The Collaborative International Dictionary of English
flowing — flowingly, adv. flowingness, n. /floh ing/, adj. 1. moving in or as in a stream: flowing water. 2. proceeding smoothly or easily; facile: flowing language. 3. long, smooth, graceful, and without sudden interruption or change of direction: flowing … Universalium
flowing — /ˈfloʊɪŋ/ (say flohing) adjective 1. that flows; moving in or as in a stream: flowing water. 2. proceeding smoothly or easily: flowing language. 3. smoothly and gracefully continuous throughout the length: flowing lines; flowing curves. 4.… …
flowing — flow|ing [ˈfləuıŋ US ˈflou ] adj 1.) hanging or moving in a smooth graceful way ▪ She had pale skin and dark, flowing hair. ▪ long, flowing robes 2.) continuing in a smooth, graceful way, with no sudden changes ▪ a flowing melody ▪ flowing curves … Dictionary of contemporary English
flowing — flow|ing [ flouıŋ ] adjective usually before noun 1. ) flowing clothes or hair hang in an attractive way: The women wore long flowing skirts. 2. ) flowing water is moving along: a fast flowing stream … Usage of the words and phrases in modern English
flowing — adjective 1) long flowing hair Syn: loose, free, unconfined, draping Ant: stiff, curly 2) the new model will have soft, flowing lines Syn: sleek, streamlined, a … Thesaurus of popular words
flowing — UK [ˈfləʊɪŋ] / US [ˈfloʊɪŋ] adjective [usually before noun] 1) flowing clothes or hair hang in an attractive way The women wore long flowing skirts. 2) flowing water is moving along a fast flowing stream … English dictionary