-
61 pince
f1. зажим; клещи; щипцы; гвоздодёр 2. цанга 3. лом, вага 4. расстояние от центра заклёпки до края листаpince américaine — 1. цанга 2. плоскогубцыpince coupante — кусачки, острогубцыpince à poinçonner — пробойник; бородокpince de serrage — зажимный патрон; цангаpince à trous — пробойник; бородок -
62 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
63 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
64 organe de serrage
зажимное устройство
Элемент(ы) зажима, необходимый(ые) для механической фиксации и электрического соединения проводника.
[ ГОСТ Р 51324.1—2005]
зажимной элемент
Часть (и) зажима, необходимая для механического прижима и электрического соединения проводника (ов), включая части, которые требуются для обеспечения надлежащего давления контакта (приложение 1).
[ ГОСТ Р 50043.1-92]EN
clamping unit
the part(s) of the terminal necessary for the mechanical clamping and the electrical connection of the conductor(s), including the parts which are necessary to ensure the correct contact pressure
[IEV number 442-06-12]FR
organe de serrage
partie d'une borne nécessaire pour le serrage mécanique et la connexion électrique du (des) conducteur(s), y compris les parties qui sont nécessaires pour assurer une pression de contact correcte
[IEV number 442-06-12]Тематики
- вывод, зажим электрический
Обобщающие термины
Синонимы
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > organe de serrage
-
65 gaine externe
защитный покров
неметаллическое покрытие, накладываемое поверх металлической, как правило, оболочки, обеспечивающее внешнюю защиту кабеля
ПРИМЕЧАНИЕ 1. В Северной Америке термин sheath обычно используется для металлических покрытий, а термин jacket используется только для неметаллических покрытий.
ПРИМЕЧАНИЕ 2. В случае выполнения специального уравнивания потенциалов наружный покров может обеспечивать электрическую изоляцию металлического покрытия, расположенного ниже.
[IEV number 461-05-04]
защитный покров кабеля
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]
защитный покров кабеля
-
[Интент]EN
oversheath
outer sheath
protective (overall) jacket (North America)
non metallic sheath applied over a covering, generally metallic, ensuring the protection of the cable from the outside
NOTE 1 – In North America, the term sheath is generally used for metallic coverings, whereas the term jacket is used only for non-metallic coverings.
NOTE 2 – In case of special bonding, the oversheath may provide electrical insulation of the underlying conducting covering.
[IEV number 461-05-04]FR
gaine externe
gaine extérieure
gaine non métallique appliquée sur un revêtement généralement métallique et assurant la protection externe du câble
NOTE 1 – En Amérique du Nord, le terme “sheath” est utilisé généralement pour les revêtements métalliques tandis que le terme “jacket” est utilisé uniquement pour des revêtements non métalliques.
NOTE 2 – Quand elle est appliquée sur un revêtement conducteur, la gaine externe peut constituer une isolation électrique appropriée dans le cas de connexion spéciale.
[IEV number 461-05-04]Тематики
- кабели, провода...
Синонимы
EN
DE
- Außenmantel, m
FR
Франко-русский словарь нормативно-технической терминологии > gaine externe
-
66 gaine extérieure
защитный покров
неметаллическое покрытие, накладываемое поверх металлической, как правило, оболочки, обеспечивающее внешнюю защиту кабеля
ПРИМЕЧАНИЕ 1. В Северной Америке термин sheath обычно используется для металлических покрытий, а термин jacket используется только для неметаллических покрытий.
ПРИМЕЧАНИЕ 2. В случае выполнения специального уравнивания потенциалов наружный покров может обеспечивать электрическую изоляцию металлического покрытия, расположенного ниже.
[IEV number 461-05-04]
защитный покров кабеля
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]
защитный покров кабеля
-
[Интент]EN
oversheath
outer sheath
protective (overall) jacket (North America)
non metallic sheath applied over a covering, generally metallic, ensuring the protection of the cable from the outside
NOTE 1 – In North America, the term sheath is generally used for metallic coverings, whereas the term jacket is used only for non-metallic coverings.
NOTE 2 – In case of special bonding, the oversheath may provide electrical insulation of the underlying conducting covering.
[IEV number 461-05-04]FR
gaine externe
gaine extérieure
gaine non métallique appliquée sur un revêtement généralement métallique et assurant la protection externe du câble
NOTE 1 – En Amérique du Nord, le terme “sheath” est utilisé généralement pour les revêtements métalliques tandis que le terme “jacket” est utilisé uniquement pour des revêtements non métalliques.
NOTE 2 – Quand elle est appliquée sur un revêtement conducteur, la gaine externe peut constituer une isolation électrique appropriée dans le cas de connexion spéciale.
[IEV number 461-05-04]Тематики
- кабели, провода...
Синонимы
EN
DE
- Außenmantel, m
FR
Франко-русский словарь нормативно-технической терминологии > gaine extérieure
-
67 extrémité de l'enroulement
- конец последнего витка соединения, выполненного накруткой
конец последнего витка соединения, выполненного накруткой
-EN
end tail
final portion of the last turn of the solid conductor in a wrapped connection, which extends beyond the last wrap-post corner being in electric contact with the conductor
[IEV number 581-23-45]FR
extrémité de l'enroulement
portion finale de la dernière spire de fil d'une connexion enroulée au-delà de la dernière arête de contact électrique avec le conducteur
[IEV number 581-23-45]4.6.5 Конец последнего витка соединения, выполненного накруткой, должен плотно прилегать к контактному штырю.
[ ГОСТ 23592-96]Тематики
Классификация
>>>EN
DE
- Endstück, n
FR
Смотри также
Франко-русский словарь нормативно-технической терминологии > extrémité de l'enroulement
68 élément de contact
контактный элемент
Деталь аппарата для цепей управления (неподвижная или подвижная, проводящая или изолированная) для замыкания или размыкания единственного пути прохождения тока в цепи.
Примечания:
1. Контактный элемент и механизм передачи усилия могут быть объединены в единый узел, но чаще один или несколько элементов могут быть скомбинированы с одним или несколькими механизмами передачи усилия, и их конструкция может быть разной.
2. В состав контактных элементов не входят катушки и магниты управления.
[ ГОСТ 50030.5.1-2005]
контактный элемент
контакт (2)
-
[IEV number 151-12-16]EN
contact member
contact (2)
conductive element intended to make an electric contact
[IEV number 151-12-16]FR
élément de contact, m
contact (2), m
élément conducteur destiné à établir un contact électrique
[IEV number 151-12-16]
[IEV number 444-04-06]EN
- Contact set - контактная группа
-
Ouput circuit - выходная цепь
contact circuit - цепь контакта
contact - контакт - Contact member - контактный элемент
- Contact point - рабочая поверхность контакт-детали, контакт-деталь
FR
- Jeu de contacts - контактная группа
-
Circuit de sortie - выходная цепь
circuit de contact - цепь контакта
contact - контакт - Element de contact - контактный элемент
-
Piece de contact - рабочая поверхность контакт-детали, контакт-деталь
[Перевод Интент]
Примечания
1 - Контактный элемент такой конструкции как на рисунке слева называют также конактная пружина.
2 - По существу, контактный элемент, это одна из частей контакта,
т. е. в замыкающем, размыкающем и переключающем контактах любой подвижный и неподвижный контакт является контактным элементом.
[Интент]Тематики
Синонимы
EN
DE
FR
контактный элемент электрического реле
Проводящая часть контакта электрического реле, электрически изолированная от другой части или других частей, если цепь контакта электрического реле разомкнута
[ ГОСТ 16022-83]Тематики
EN
DE
FR
102. Контактный элемент электрического реле
D. Kontaktglied
E. Contact member
F. Elément de contact
Проводящая часть контакта электрического реле, электрически изолированная от другой части или других частей, если цепь контакта электрического реле разомкнута
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Франко-русский словарь нормативно-технической терминологии > élément de contact
69 tension phase-terre, f
напряжение линейного проводника относительно земли
Нрк. фазное напряжение относительно земли
Напряжение между линейным проводником и эталонной (относительной) землей в данной точке электрической цепи.
[ ГОСТ Р МЭК 60050-826-2009]
фазное напряжение относительно земли
Напряжение между линейным проводником и относительной землей в данной точке электрической цепи переменного тока.
[ ГОСТ Р МЭК 60050-195-2005]EN
line-to-earth voltage
line-to-ground voltage (US)
phase-to-earth voltage (deprecated)
voltage between a line conductor and reference earth at a given point of an electric circuit
Source: 195-05-03
[IEV number 826-11-08]FR
tension phase-terre, f
tension entre un conducteur de ligne et la terre de référence en un point donné d'un circuit électrique
Source: 195-05-03
[IEV number 826-11-08]Недопустимые, нерекомендуемые
Тематики
EN
DE
- Spannung Außenleiter - Erde, f
FR
- tension phase-terre, f
Франко-русский словарь нормативно-технической терминологии > tension phase-terre, f
70 connexion soudée
паяное соединение
Соединение, образованное пайкой
[ ГОСТ 17325-79]
[ ГОСТ 23887-79]
паяное соединение
Способ соединения, при котором проводник фиксируют механически, а непрерывность цепи обеспечивают пайкой.
[ГОСТ IЕС 60730-1-2011]
паяное соединение
-
[IEV number 581-23-04]EN
soldered connection
connection made by soldering
[IEV number 581-23-04]
solder termination
termination in which the conductor is secured by a mechanical means, and the circuit continuity is assured by solder
[IEC 60730-1, ed. 5.0 (2013-11)]FR
connexion soudée
connexion obtenue par soudure
[IEV number 581-23-04]
connexion soudée
connexion dans laquelle le conducteur est fixé mécaniquement et la continuité électrique est assurée par une soudure
[IEC 60730-1, ed. 5.0 (2013-11)]Тематики
- сборка
- сварка, резка, пайка
- соединение контактное
Обобщающие термины
EN
DE
- Lötverbindung, f
FR
Франко-русский словарь нормативно-технической терминологии > connexion soudée
СтраницыСм. также в других словарях:
Conducteur électrique — Conducteur (physique) Pour les articles homonymes, voir Conducteur. En physique, un conducteur est un matériau permettant des échanges d énergie entre deux systèmes, par opposition à un isolant. On distingue conducteurs électriques et les… … Wikipédia en Français
conducteur électrique — elektros laidininkas statusas T sritis fizika atitikmenys: angl. conductor of electricity vok. elektrischer Leiter, m rus. электрический проводник, m pranc. conducteur électrique, m … Fizikos terminų žodynas
Conducteur (Physique) — Pour les articles homonymes, voir Conducteur. En physique, un conducteur est un matériau permettant des échanges d énergie entre deux systèmes, par opposition à un isolant. On distingue conducteurs électriques et les conducteurs thermiques.… … Wikipédia en Français
Conducteur En Équilibre Électrostatique — Un conducteur électrique en équilibre électrostatique est un conducteur pour lequel les charges libres sont en moyenne fixes, par conséquent il y a absence de courant à l intérieur de celui ci. Supposons ce conducteur ohmique i.e. qu il vérifie… … Wikipédia en Français
Conducteur en equilibre electrostatique — Conducteur en équilibre électrostatique Un conducteur électrique en équilibre électrostatique est un conducteur pour lequel les charges libres sont en moyenne fixes, par conséquent il y a absence de courant à l intérieur de celui ci. Supposons ce … Wikipédia en Français
Conducteur (physique) — Pour les articles homonymes, voir Conducteur. En physique, un conducteur est un matériau permettant des échanges d énergie entre deux systèmes, par opposition à un isolant. On distingue les conducteurs d’électricité et les conducteurs thermiques … Wikipédia en Français
Conducteur en équilibre électrostatique — Un conducteur électrique en équilibre électrostatique est un conducteur qui n est parcouru par aucun courant. Cela signifie que toutes les charges électriques libres internes au conducteur sont toutes immobiles . Dans n importe quel conducteur,… … Wikipédia en Français
électrique — (é lèk tri k ) adj. 1° Terme de physique. Qui a rapport à l électricité, qui la développe ou en provient. Machine, batterie électrique. Courant, étincelle électrique. Force électrique, la cause inconnue des phénomènes de l électricité.… … Dictionnaire de la Langue Française d'Émile Littré
électrique — [ elɛktrik ] adj. • 1660; angl. electrick (1646); lat. sc. electricus « propre à l ambre » (1600); lat. electrum 1 ♦ Vx Qui peut recevoir ou communiquer l électricité. ♢ Mod. Propre ou relatif à l électricité. L énergie électrique. Phénomènes… … Encyclopédie Universelle
conducteur — conducteur, trice [ kɔ̃dyktɶr, tris ] n. et adj. • mil. XIVe; de conduire, d apr. lat. conductor I ♦ Personne qui conduit qqn ou qqch. 1 ♦ Littér. Personne qui dirige, mène des hommes. ⇒ berger, chef, guide, pasteur; leader. « Moïse a la grandeur … Encyclopédie Universelle
conducteur — conducteur, trice (kon du kteur, ktri s ) s. m. et f. 1° Celui, celle qui conduit. Le conducteur d une barque. Moïse était le conducteur du peuple de Dieu. • Ceux ci allaient toujours, sans regarder qu ils allaient à la servitude ; et leur… … Dictionnaire de la Langue Française d'Émile Littré
Перевод: с французского на все языки
со всех языков на французский- Со всех языков на:
- Французский
- С французского на:
- Все языки
- Английский
- Немецкий
- Португальский
- Русский
- Узбекский