-
1 wiederkehrende Spannung
- восстанавливающееся напряжение (для контактора и пускателя)
- восстанавливающееся напряжение
- восстанавливающееся и возвращающееся напряжение
восстанавливающееся и возвращающееся напряжение
Напряжение, появляющееся на выводах полюса коммутационного аппарата или плавкого предохранителя после отключения тока..
Примечания
1 Напряжение можно рассматривать на протяжении двух последовательных интервалов времени, на первом из которых напряжение переходное, а на последующем — промышленной частоты.
2 Определение действительно для однополюсного аппарата. Для многополюсного аппарата — это межфазное напряжение на входных выводах аппаратов.
МЭК 60050(441-17-25)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
recovery voltage
the voltage which appears across the terminals of a pole of a switching device or a fuse after the breaking of the current
NOTE – This voltage may be considered in two successive intervals of time, one during which a transient voltage exists, followed by a second one during which the power frequency or the steady-state recovery voltage alone exists.
[IEV number 441-17-25]FR
tension de rétablissement
tension qui apparaît entre les bornes d'un appareil de connexion ou d'un fusible après l'interruption du courant
NOTE – Cette tension peut être considérée durant deux intervalles de temps consécutifs, l'un durant lequel existe une tension transitoire, suivi par un second intervalle durant lequel la tension de rétablissement à fréquence industrielle ou en régime établi existe seule.
[IEV number 441-17-25]Тематики
- электротехника, основные понятия
EN
DE
FR
восстанавливающееся напряжение
Напряжение, появляющееся на выводах полюса автоматического выключателя после отключения тока.
Примечания
1 Это напряжение можно рассматривать на протяжении двух последовательных интервалов времени, на первом из которых напряжение переходное, а на последующем втором — напряжение промышленной частоты.
2 Это определение действительно для однополюсного выключателя. Для многополюсного выключателя — это напряжение между входными выводами аппарата
(МЭС 441-17-25)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
восстанавливающееся напряжение
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]EN
recovery voltage
the voltage which appears across the terminals of a pole of a switching device or a fuse after the breaking of the current
NOTE – This voltage may be considered in two successive intervals of time, one during which a transient voltage exists, followed by a second one during which the power frequency or the steady-state recovery voltage alone exists.
[IEV number 441-17-25]FR
tension de rétablissement
tension qui apparaît entre les bornes d'un appareil de connexion ou d'un fusible après l'interruption du courant
NOTE – Cette tension peut être considérée durant deux intervalles de temps consécutifs, l'un durant lequel existe une tension transitoire, suivi par un second intervalle durant lequel la tension de rétablissement à fréquence industrielle ou en régime établi existe seule
[IEV number 441-17-25]Тематики
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
EN
- cleaning voltage
- recovery voltage
- restoring voltage
- restriking voltage
- transient recovery voltage
- TRV
DE
FR
восстанавливающееся напряжение
Напряжение, появляющееся на выводах полюса автоматического выключателя после отключения тока.
Примечания
1 Это напряжение можно рассматривать на протяжении двух последовательных интервалов времени, на первом из которых напряжение переходное, а на последующем втором — напряжение промышленной частоты.
2 Это определение действительно для однополюсного выключателя. Для многополюсного выключателя — это напряжение между входными выводами аппарата
3 У вакуумного контактора или пускателя наибольшее восстанавливающееся напряжение возможно не на первом отключаемом полюсе
(МЭС 441-17-25)
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]EN
recovery voltage
the voltage which appears across the terminals of a pole of a switching device or a fuse after the breaking of the current
NOTE – This voltage may be considered in two successive intervals of time, one during which a transient voltage exists, followed by a second one during which the power frequency or the steady-state recovery voltage alone exists.
[IEV number 441-17-25]FR
tension de rétablissement
tension qui apparaît entre les bornes d'un appareil de connexion ou d'un fusible après l'interruption du courant
NOTE – Cette tension peut être considérée durant deux intervalles de temps consécutifs, l'un durant lequel existe une tension transitoire, suivi par un second intervalle durant lequel la tension de rétablissement à fréquence industrielle ou en régime établi existe seule
[IEV number 441-17-25]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > wiederkehrende Spannung
-
2 Verzögerungsschalter
аппарат с выдержкой времени
Коммутационный электрический аппарат, имеющий устройство, обеспечивающее специально предусмотренную выдержку времени от момента подачи команды на выполнение коммутационной операции до начала ее выполнения.
[ ГОСТ 17703-72]EN
time-delay switch
TDS
switch provided with a time-delay device which operates for a certain time (the delay time). It may be either manually actuated and/or remotely electrically initiated
[IEC 60669-2-3, ed. 3.0 (2006-08)]
time-delay switch
TDS
a switch provided with a time-delay device, which operates for a certain time (the delay time) and which is operated by hand and/or by remote control by means of pulses
[IEV number 442-04-33]
mechanical time-delay device
device which, through a mechanical auxiliary, operates some time after the instant at which the conditions which cause it to operate are established
NOTE - This definition is only applicable to the switching circuit.
[IEC 60669-2-3, ed. 3.0 (2006-08)]FR
interrupteurs temporisés (minuteries)
interrupteur pourvu d’un dispositif de temporisation qui le fait fonctionner pendant un certain temps (la temporisation). Il peut être commandé manuellement et/ou lancé électriquement à distance
[IEC 60669-2-3, ed. 3.0 (2006-08)]
interrupteur temporisé
interrupteur pourvu d'un dispositif de temporisation qui le fait fonctionner pendant un certain temps (la temporisation) et qui est commandé manuellement et/ou à distance au moyen d'impulsions
[IEV number 442-04-33]
dispositif mécanique à action différée
dispositif qui, par l'effet d'un auxiliaire mécanique, fonctionne un certain temps après l'instant où les conditions prévues pour son fonctionnement sont réalisées
NOTE - Cette définition s’applique seulement au circuit de l’interrupteur.
[IEC 60669-2-3, ed. 3.0 (2006-08)]Тематики
- аппарат, изделие, устройство...
EN
DE
FR
выключатель с выдержкой времени (таймер)
Выключатель, имеющий устройство выдержки времени, которое приводит его в действие на определенное время, по истечении которого автоматически разрывается цепь выключателя, и управляемый вручную и/или дистанционно импульсным методом.
[ ГОСТ Р 51324.2.3-99 (МЭК 60669-2-3-97)]
выключатель с выдержкой времени
-
[IEV number 442-04-33]EN
ime-delay switch
TDS (abbreviation)
a switch provided with a time-delay device, which operates for a certain time (the delay time) and which is operated by hand and/or by remote control by means of pulses
[IEV number 442-04-33]FR
interrupteur temporisé
interrupteur pourvu d'un dispositif de temporisation qui le fait fonctionner pendant un certain temps (la temporisation) et qui est commandé manuellement et/ou à distance au moyen d'impulsions
[IEV number 442-04-33]Тематики
- выключатель, переключатель
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Verzögerungsschalter
-
3 Zeitschalter
аппарат с выдержкой времени
Коммутационный электрический аппарат, имеющий устройство, обеспечивающее специально предусмотренную выдержку времени от момента подачи команды на выполнение коммутационной операции до начала ее выполнения.
[ ГОСТ 17703-72]EN
time-delay switch
TDS
switch provided with a time-delay device which operates for a certain time (the delay time). It may be either manually actuated and/or remotely electrically initiated
[IEC 60669-2-3, ed. 3.0 (2006-08)]
time-delay switch
TDS
a switch provided with a time-delay device, which operates for a certain time (the delay time) and which is operated by hand and/or by remote control by means of pulses
[IEV number 442-04-33]
mechanical time-delay device
device which, through a mechanical auxiliary, operates some time after the instant at which the conditions which cause it to operate are established
NOTE - This definition is only applicable to the switching circuit.
[IEC 60669-2-3, ed. 3.0 (2006-08)]FR
interrupteurs temporisés (minuteries)
interrupteur pourvu d’un dispositif de temporisation qui le fait fonctionner pendant un certain temps (la temporisation). Il peut être commandé manuellement et/ou lancé électriquement à distance
[IEC 60669-2-3, ed. 3.0 (2006-08)]
interrupteur temporisé
interrupteur pourvu d'un dispositif de temporisation qui le fait fonctionner pendant un certain temps (la temporisation) et qui est commandé manuellement et/ou à distance au moyen d'impulsions
[IEV number 442-04-33]
dispositif mécanique à action différée
dispositif qui, par l'effet d'un auxiliaire mécanique, fonctionne un certain temps après l'instant où les conditions prévues pour son fonctionnement sont réalisées
NOTE - Cette définition s’applique seulement au circuit de l’interrupteur.
[IEC 60669-2-3, ed. 3.0 (2006-08)]Тематики
- аппарат, изделие, устройство...
EN
DE
FR
выключатель с выдержкой времени (таймер)
Выключатель, имеющий устройство выдержки времени, которое приводит его в действие на определенное время, по истечении которого автоматически разрывается цепь выключателя, и управляемый вручную и/или дистанционно импульсным методом.
[ ГОСТ Р 51324.2.3-99 (МЭК 60669-2-3-97)]
выключатель с выдержкой времени
-
[IEV number 442-04-33]EN
ime-delay switch
TDS (abbreviation)
a switch provided with a time-delay device, which operates for a certain time (the delay time) and which is operated by hand and/or by remote control by means of pulses
[IEV number 442-04-33]FR
interrupteur temporisé
interrupteur pourvu d'un dispositif de temporisation qui le fait fonctionner pendant un certain temps (la temporisation) et qui est commandé manuellement et/ou à distance au moyen d'impulsions
[IEV number 442-04-33]Тематики
- выключатель, переключатель
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Zeitschalter
-
4 Wettbewerbsverzerrung
нарушение условий конкуренции
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
distortion of competition
Article 85(1) of the EEC Treaty prohibits all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market. All such arrangements are automatically null and void under Article 85(2), unless exempted by the Commission pursuant to Article 85(3). The text of Article 85 is as follows: "1. The following shall be prohibited as incompatible with the common market: all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market, and in particular those which: (a) directly or indirectly fix purchase or selling prices or any other trading conditions; (b) limit or control production, markets, technical development, or investment; (c) share markets or sources of supply; (d) apply dissimilar conditions to equivalent transactions with other trading parties, thereby placing them at a competitive disadvantage; (e) make the conclusion of contracts subject to acceptance by the other parties of supplementary obligations which, by their nature or according to commercial usage, have no connection with the subject of such contracts. (Source: CLAORG)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Wettbewerbsverzerrung
-
5 Wettbewerbsbeschänkung
ограничение конкуренции
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
restriction on competition
Article 85(1) of the EEC Treaty prohibits all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market. All such arrangements are automatically null and void under Article 85(2), unless exempted by the Commission pursuant to Article 85(3). The text of Article 85 is as follows: "1. The following shall be prohibited as incompatible with the common market: all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market, and in particular those which: (a) directly or indirectly fix purchase or selling prices or any other trading conditions; (b) limit or control production, markets, technical development, or investment; (c) share markets or sources of supply; (d) apply dissimilar conditions to equivalent transactions with other trading parties, thereby placing them at a competitive disadvantage; (e) make the conclusion of contracts subject to acceptance by the other parties of supplementary obligations which, by their nature or according to commercial usage, have no connection with the subject of such contracts. (Source: CLAORG)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Wettbewerbsbeschänkung
-
6 Körper (eines elektrischen Betriebsmittels)
открытая проводящая часть
Проводящая часть, которой легко коснуться и которая в нормальных условиях эксплуатации не находится под напряжением, но может оказаться под ним в аварийных условиях.
(МЭС 441-11-10).
Примечание. К типичным открытым проводящим частям относятся стенки оболочек, ручки управления и т. п.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
открытая проводящая часть
Доступная прикосновению проводящая часть электрооборудования, которая обычно не находится под напряжением, но может оказаться под напряжением при повреждении основной изоляции.
Открытая проводящая часть представляет собой доступную прикосновению проводящую часть электрооборудования, которая, в отличие от токоведущих частей, не находится под напряжением при нормальных условиях. Человек и животные, находящиеся в здании, имеют многочисленные контакты с открытыми проводящими частями, во время которых они не подвергаются опасности поражения электрическим током. Если произошло повреждение основной изоляции опасной токоведущей части, открытая проводящая часть может оказаться под напряжением. Тогда она будет представлять реальную угрозу для человека и животных, которые прикоснулись к ней. К открытым проводящим частям, прежде всего, относят металлические оболочки и доступную прикосновению арматуру электрооборудования класса 0 и класса I, например, металлические корпусы холодильников, стиральных машин, электрических плит, металлическую арматуру светильников и др.
[ http://www.volt-m.ru/glossary/letter/%CE/view/45/]
открытая проводящая часть
ТокопроводящаяПроводящая часть электрического оборудования, доступная прикосновению, которая обычно не находится, но может оказаться под напряжением в случае повреждения (МЭС 826-03-02, с изменением).
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
открытые проводящие части
Нетоковедущие, части, доступные прикосновению человека, между которыми или между ними и землей при нарушении изоляции токоведущих частей может возникнуть относительно земли напряжение, превышающее предельно допустимое для человека значение напряжения прикосновения. При этом под нетоковедущей частью понимается электропроводящая часть электроустановки, не находящаяся в процессе ее работы под рабочим напряжением.
[ ГОСТ Р 50669-94]
открытая проводящая часть
Доступная для прикосновения проводящая часть оборудования, которая нормально не находится под напряжением, но может оказаться под напряжением при повреждении основной изоляции.
[ ГОСТ Р МЭК 60050-195-2005]
[ ГОСТ Р МЭК 60050-826-2009]
открытаятокопроводящаяпроводящая часть
ТокопроводящаяПроводящая часть электрического оборудования, к которой можно прикоснуться и которая обычно не находится под напряжением, но в случае повреждения может оказаться под напряжением.
Примечание -ТокопроводящуюПроводящую часть электрического оборудования, которая в результате повреждения может оказаться под напряжением через открытуютокопроводящую часть, не считают открытой токопроводящей частью.
[ГОСТ ЕН 1070-2003]
открытая проводящая часть
незащищенная токопроводящая
Проводящая часть электрооборудования, которой можно коснуться и которая обычно не находится под напряжением, но в случаенеполадки может стать таковойповреждения может оказаться под напряжением.
[МЭС 826-12-10, модифицированный]
[ ГОСТ Р МЭК 60204-1-2007]EN
exposed-conductive-part
conductive part of equipment which can be touched and which is not normally live, but which can become live when basic insulation fails
Source: 195-06-10
[IEV number 826-12-10]
exposed conductive part
conductive part of electrical equipment, which can be touched and which is not live under normal operating conditions, but which can become live under fault conditions
[IEV 826-12-10, modified]
[IEC 60204-1, ed. 5.0 (2005-10)]
[IEC 60204-1-2006]FR
partie conductrice accessible, f
masse (dans une installation électrique), f
partie conductrice d'un matériel, susceptible d'être touchée, et qui n'est pas normalement sous tension, mais peut le devenir lorsque l'isolation principale est défaillante
Source: 195-06-10
[IEV number 826-12-10]
partie conductrice accessible;
masse
partie conductrice d'un matériel électrique susceptible d'être touchée et qui n'est pas normalement sous tension mais qui peut le devenir en cas de défaut
[IEC 60204-1, ed. 5.0 (2005-10)]Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Körper (eines elektrischen Betriebsmittels)
-
7 Leistungsschalter mit Einschaltsperre
- автоматический выключатель с блокировкой, препятствующей замыканию
автоматический выключатель с блокировкой, препятствующей замыканию
Выключатель, каждый подвижный контакт которого защищен от замыкания, достаточного для прохождения тока, если команда на включение подается в то время, как сохраняются определенные условия.
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]EN
circuit-breaker with lock-out preventing closing
a circuit-breaker in which none of the moving contacts can make current if the closing command is initiated while the conditions which should cause the opening operation remain established.
[IEC 62271-100, ed. 2.0 (2008-04)]
circuit-breaker with lock-out device preventing closing
a circuit-breaker in which each of the moving contacts is prevented from closing sufficiently to be capable of passing current if the closing command is initiated while specified conditions remain established.
[IEC 60947-2, ed. 4.0 (2006-05)]
circuit-breaker with lock-out preventing closing
a circuit-breaker in which none of the moving contacts can make current if the closing command is initiated while the conditions which should cause the opening operation remain established
[IEV number 441-14-23]FR
disjoncteur à fermeture empêchée
disjoncteur dont aucun des contacts mobiles ne peut établir le courant si l’ordre de fermeture est donné alors que demeurent maintenues les conditions qui devraient provoquer la manceuvre d’ouverture.
[IEC 62271-100, ed. 2.0 (2008-04)]
disjoncteur à fermeture empêchée
disjoncteur dont chacun des contacts mobiles est empêché de se fermer suffisamment pour être capable de laisser passer le courant si l’ordre de fermeture est donné alors que demeurent maintenues des conditions spécifiées.
[IEC 60947-2, ed. 4.0 (2006-05)]
disjoncteur à fermeture empêchée
disjoncteur dont aucun des contacts mobiles ne peut établir le courant si l'ordre de fermeture est donné alors que demeurent maintenues les conditions qui devraient provoquer la manoeuvre d'ouverture
[IEV number 441-14-23]Тематики
Классификация
>>>Обобщающие термины
EN
- circuit breaker with lock-out device preventing closing
- circuit breaker with lock-out preventing closing
- circuit-breaker with lock-out device preventing closing
- circuit-breaker with lock-out preventing closing
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Leistungsschalter mit Einschaltsperre
-
8 Schaltanlagen und/oder Schaltgeräte
аппаратура распределения и управления
Общий термин для коммутационных аппаратов и их комбинации с относящимися к ним устройствами управления, измерения, защиты и регулирования, а также для узлов, в которых такие аппараты и устройства соединяются с соответствующими фидерами, комплектующим оборудованием, оболочками и опорными конструкциями.
МЭК 60050 (441-11-01) [1].
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
switchgear and controlgear
general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEC 62271-1, ed. 1.0 (2007-10)]FR
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu’aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEC 62271-1, ed. 1.0 (2007-10)]Тематики
- аппарат, изделие, устройство...
EN
DE
- Schaltanlagen und/oder Schaltgeräte
FR
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
Немецко-русский словарь нормативно-технической терминологии > Schaltanlagen und/oder Schaltgeräte
-
9 atmosphärisches Ozon
атмосферный озон
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
atmospheric ozone
A triatomic molecule of oxygen; a natural constituent of the atmosphere, with the highest concentrations in the ozone layer or stratosphere; it is found at a level between 15 and 30 km above the Earth, which prevents harmful ultraviolet B radiation, which causes skin cancer and threatens plant life, from reaching the ground. The fragile shield is being damaged by chemicals released on Earth. The main chemicals that are depleting stratospheric ozone are chlorofluorocarbons (CFCs), which are used in refrigerators, aerosols and as cleaners in many industries and halons, which are used in fire extinguishers. The damage is caused when these chemicals release highly reactive forms of chlorine and bromine. (Source: GILP96 / WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > atmosphärisches Ozon
-
10 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
11 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
12 Betätigungsglied
исполнительный элемент
Часть, которую тянут, на которую нажимают, которую поворачивают или перемещают иным образом, чтобы изменить положение контактов выключателя.
[< size="2"> ГОСТ Р 51324. 1-2005 ( МЭК 60669-1: 2000)]EN
actuating member
a part which is pulled, pushed, turned or otherwise moved to cause an operation of the switch
[IEV number 442-04-14]FR
organe de manoeuvre
partie qui est tirée, poussée, tournée ou manipulée de toute autre façon pour provoquer le fonctionnement de l'interrupteur
[IEV number 442-04-14]Тематики
- выключатель, переключатель
- изделие электроустановочное
EN
DE
FR
орган управления
Частьсистемыаппарата управления, к которой прилагается извне усилие управления.
МЭК 60050(441-15-22).
Примечание. Орган управления может иметь форму рукоятки, ручки, нажимной кнопки, ролика, плунжера и т. п.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
орган управления
Часть приводного механизма, к которой прикладывается внешняя сила воздействия.
Примечание - Орган управления может иметь форму ручки, кнопки, ролика, поршня и т.д.
[ ГОСТ Р 52726-2007]
орган управления
Часть системы привода, подвергаемая внешнему силовому воздействию.
Примечания
1. Орган управления может иметь форму ручки, рукоятки, нажимной кнопки, ролика, плунжера и т.д.
2. Есть несколько способов приведения в действие, которые не требуют внешнего силового воздействия, а только какого-либо действия.
[ГОСТ ЕН 1070-2003]
орган управления
Часть системы управления, которая предназначена непосредственно для воздействия оператором, например путем нажатия.
[ГОСТ Р ЕН 614-1-2003]
орган управления
Часть системы приведения в действие, которая принимает воздействие человека.
[ ГОСТ Р МЭК 60447-2000]
орган управления
Часть системы приведения в действие, которая воспринимает воздействие человека (ГОСТ Р МЭК 60447).
Примечание
В настоящем стандарте орган управления в виде интерактивного экранного устройства отображения является частью этого устройства, которое представляет функцию органа управления.
[ ГОСТ Р МЭК 60073-2000]
орган управления
Часть механизма прибора управления, на который оказывается вручную внешнее силовое воздействие.
Примечание.
Орган управления может иметь форму ручки, рукоятки, кнопки, ролика, плунжера и т.д.
Некоторые органы управления не требуют воздействия внешней силы, а только какого-либо действия.
[ ГОСТ Р МЭК 60204-1-2007]
органы управления
Ручки, переключатели, потенциометры и другие органы, служащие для включения и регулировки аппаратуры. Термин относится преимущественно к аналоговым приборам.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
орган управления
-
[IEV number 442-04-14]
средства оперирования
-
[Интент]EN
actuator
the part of the actuating system to which an external actuating force is applied
NOTE – The actuator may take the form of a handle, knob, push-button, roller, plunger, etc.
[IEV number 441-15-22]
actuator
part of a device to which an external manual action is to be applied
NOTE 1 The actuator may take the form of a handle, knob, push-button, roller, plunger, etc.
NOTE 2 There are some actuating means that do not require an external actuating force, but only an action.
NOTE 3 See also 3.34.
[IEC 60204-1 -2005]
actuating member
a part which is pulled, pushed, turned or otherwise moved to cause an operation of the switch
[IEV number 442-04-14]FR
organe de commande
partie du mécanisme transmetteur à laquelle un effort extérieur de manoeuvre est appliqué
NOTE – L'organe de commande peut prendre la forme d'une poignée, d'un bouton, d'un bouton-poussoir, d'une roulette, d'un plongeur, etc.
[IEV number 441-15-22]
organe de manoeuvre
partie qui est tirée, poussée, tournée ou manipulée de toute autre façon pour provoquer le fonctionnement de l'interrupteur
[IEV number 442-04-14]
Аппарат должен оставаться механически действующим. Не допускается сваривание контактов, препятствующее операции размыкания при использовании нормальных средств оперирования.
[ГОСТ Р 50030.3-99 (МЭК 60947-3-99) ]
ВДТ следует оперировать как при нормальной эксплуатации. Операции размыкания должны проводиться в следующем порядке:
для первых 1000 циклов — с использованием ручных средств оперирования;...
[ ГОСТ Р 51326. 1-99 ( МЭК 61008-1-96)]Параллельные тексты EN-RU
The operating means (for example, a handle) of the supply disconnecting device shall be easily accessible and located between 0,6 m and 1,9 m above the servicing level.
[IEC 60204-1-2006]Органы управления, например, рукоятки аппаратов отключения питания, должны быть легко доступны и располагаться на высоте от 0,6 до 1,9 м от рабочей площадки.
[Перевод Интент]Where the external operating means is not intended for emergency operations, it is recommended that it be coloured BLACK or GREY.
[IEC 60204-1-2006]Если внешние средства оперирования не предназначены для выполнения действий при возникновении аварийных ситуаций, то рекомендуется, применять такие средства ЧЕРНОГО или СЕРОГО цвета.
[Перевод Интент]1.2.2. Control devices
Control devices must be:
— clearly visible and identifiable and appropriately marked where necessary,
— positioned for safe operation without hesitation or loss of time, and without ambiguity,
— designed so that the movement of the control is consistent with its effect,
— located outside the danger zones, except for certain controls where necessary, such as emergency stop, console for training of robots,
— positioned so that their operation cannot cause additional risk,
— designed or protected so that the desired effect, where a risk is involved, cannot occur without an intentional operation,
— made so as to withstand foreseeable strain; particular attention must be paid to emergency stop devices liable to be subjected to considerable strain.1.2.2. Органы управления
Органы управления должны быть:
- четко видны, хорошо различимы и, где это необходимо, иметь соответствующее обозначение;
- расположены так, чтобы ими можно было пользоваться без возникновения сомнений и потерь времени на выяснение их назначения;
- сконструированы так, чтобы перемещение органа управления согласовывалось с их воздействием;
- расположены вне опасных зон; исключение, где это необходимо, делается для определенных средств управления, таких, как средство экстренной остановки, пульт управления роботом;
- расположены так, чтобы их использование не вызывало дополнительных рисков;
- сконструированы или защищены так, чтобы в случаях, где возможно возникновение рисков, они не могли бы возникнуть без выполнения намеренных действий;
- сделаны так, чтобы выдерживать предполагаемую нагрузку; при этом особое внимание уделяется органам аварийного останова, которые могут подвергаться значительным нагрузкам.Where a control is designed and constructed to perform several different actions, namely where there is no one-to-one correspondence (e.g. keyboards, etc.), the action to be performed must be clearly displayed and subject to confirmation where necessary.
Если орган управления предназначен для выполнения разных действий, например, если в качестве органа управления используется клавиатура или аналогичное устройство, то должна выводиться четкая информация о предстоящем действии, и, если необходимо, должно выполняться подтверждение на выполнение такого действия.
Controls must be so arranged that their layout, travel and resistance to operation are compatible with the action to be performed, taking account of ergonomic principles.
Органы управления должны быть организованы таким образом, чтобы их расположение, перемещение их элементов и усилие, которое оператор затрачивает на их перемещение, соответствовали выполняемым операциям и принципам эргономики.
Constraints due to the necessary or foreseeable use of personal protection equipment (such as footwear, gloves, etc.) must be taken into account.
Необходимо учитывать скованность движений операторов при использовании необходимых или предусмотренных средств индивидуальной защиты (таких, как специальная обувь, перчатки и др.).
Machinery must be fitted with indicators (dials, signals, etc.) as required for safe operation. The operator must be able to read them from the control position.
Для обеспечения безопасной эксплуатации машинное оборудование должно быть оснащено индикаторами (циферблатами, устройствами сигнализации и т. д.). Оператор должен иметь возможность считывать их с места управления.
From the main control position the operator must be able to ensure that there are no exposed persons in the danger zones.
Находясь в главном пункте управления, оператор должен иметь возможность контролировать отсутствие незащищенных лиц.
If this is impossible, the control system must be designed and constructed so that an acoustic and/ or visual warning signal is given whenever the machinery is about to start.
Если это невозможно, то система управления должна быть разработана и изготовлена так, чтобы перед каждым пуском машинного оборудования подавался звуковой и/или световой предупредительный сигнал.
The exposed person must have the time and the means to take rapid action to prevent the machinery starting up.
[DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL]
Незащищенное лицо должно иметь достаточно времени и средств для быстрого предотвращения пуска машинного оборудования.
[Перевод Интент]
Тематики
- автоматизация, основные понятия
- аппарат, изделие, устройство...
- безопасность машин и труда в целом
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
- электробезопасность
- электротехника, основные понятия
Синонимы
EN
- actuating member
- actuator
- command unit
- control
- control device
- controller
- controls
- operating control
- operating means
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Betätigungsglied
-
13 Betätigungsorgan
исполнительный элемент
Часть, которую тянут, на которую нажимают, которую поворачивают или перемещают иным образом, чтобы изменить положение контактов выключателя.
[< size="2"> ГОСТ Р 51324. 1-2005 ( МЭК 60669-1: 2000)]EN
actuating member
a part which is pulled, pushed, turned or otherwise moved to cause an operation of the switch
[IEV number 442-04-14]FR
organe de manoeuvre
partie qui est tirée, poussée, tournée ou manipulée de toute autre façon pour provoquer le fonctionnement de l'interrupteur
[IEV number 442-04-14]Тематики
- выключатель, переключатель
- изделие электроустановочное
EN
DE
FR
орган управления
Частьсистемыаппарата управления, к которой прилагается извне усилие управления.
МЭК 60050(441-15-22).
Примечание. Орган управления может иметь форму рукоятки, ручки, нажимной кнопки, ролика, плунжера и т. п.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
орган управления
Часть приводного механизма, к которой прикладывается внешняя сила воздействия.
Примечание - Орган управления может иметь форму ручки, кнопки, ролика, поршня и т.д.
[ ГОСТ Р 52726-2007]
орган управления
Часть системы привода, подвергаемая внешнему силовому воздействию.
Примечания
1. Орган управления может иметь форму ручки, рукоятки, нажимной кнопки, ролика, плунжера и т.д.
2. Есть несколько способов приведения в действие, которые не требуют внешнего силового воздействия, а только какого-либо действия.
[ГОСТ ЕН 1070-2003]
орган управления
Часть системы управления, которая предназначена непосредственно для воздействия оператором, например путем нажатия.
[ГОСТ Р ЕН 614-1-2003]
орган управления
Часть системы приведения в действие, которая принимает воздействие человека.
[ ГОСТ Р МЭК 60447-2000]
орган управления
Часть системы приведения в действие, которая воспринимает воздействие человека (ГОСТ Р МЭК 60447).
Примечание
В настоящем стандарте орган управления в виде интерактивного экранного устройства отображения является частью этого устройства, которое представляет функцию органа управления.
[ ГОСТ Р МЭК 60073-2000]
орган управления
Часть механизма прибора управления, на который оказывается вручную внешнее силовое воздействие.
Примечание.
Орган управления может иметь форму ручки, рукоятки, кнопки, ролика, плунжера и т.д.
Некоторые органы управления не требуют воздействия внешней силы, а только какого-либо действия.
[ ГОСТ Р МЭК 60204-1-2007]
органы управления
Ручки, переключатели, потенциометры и другие органы, служащие для включения и регулировки аппаратуры. Термин относится преимущественно к аналоговым приборам.
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
орган управления
-
[IEV number 442-04-14]
средства оперирования
-
[Интент]EN
actuator
the part of the actuating system to which an external actuating force is applied
NOTE – The actuator may take the form of a handle, knob, push-button, roller, plunger, etc.
[IEV number 441-15-22]
actuator
part of a device to which an external manual action is to be applied
NOTE 1 The actuator may take the form of a handle, knob, push-button, roller, plunger, etc.
NOTE 2 There are some actuating means that do not require an external actuating force, but only an action.
NOTE 3 See also 3.34.
[IEC 60204-1 -2005]
actuating member
a part which is pulled, pushed, turned or otherwise moved to cause an operation of the switch
[IEV number 442-04-14]FR
organe de commande
partie du mécanisme transmetteur à laquelle un effort extérieur de manoeuvre est appliqué
NOTE – L'organe de commande peut prendre la forme d'une poignée, d'un bouton, d'un bouton-poussoir, d'une roulette, d'un plongeur, etc.
[IEV number 441-15-22]
organe de manoeuvre
partie qui est tirée, poussée, tournée ou manipulée de toute autre façon pour provoquer le fonctionnement de l'interrupteur
[IEV number 442-04-14]
Аппарат должен оставаться механически действующим. Не допускается сваривание контактов, препятствующее операции размыкания при использовании нормальных средств оперирования.
[ГОСТ Р 50030.3-99 (МЭК 60947-3-99) ]
ВДТ следует оперировать как при нормальной эксплуатации. Операции размыкания должны проводиться в следующем порядке:
для первых 1000 циклов — с использованием ручных средств оперирования;...
[ ГОСТ Р 51326. 1-99 ( МЭК 61008-1-96)]Параллельные тексты EN-RU
The operating means (for example, a handle) of the supply disconnecting device shall be easily accessible and located between 0,6 m and 1,9 m above the servicing level.
[IEC 60204-1-2006]Органы управления, например, рукоятки аппаратов отключения питания, должны быть легко доступны и располагаться на высоте от 0,6 до 1,9 м от рабочей площадки.
[Перевод Интент]Where the external operating means is not intended for emergency operations, it is recommended that it be coloured BLACK or GREY.
[IEC 60204-1-2006]Если внешние средства оперирования не предназначены для выполнения действий при возникновении аварийных ситуаций, то рекомендуется, применять такие средства ЧЕРНОГО или СЕРОГО цвета.
[Перевод Интент]1.2.2. Control devices
Control devices must be:
— clearly visible and identifiable and appropriately marked where necessary,
— positioned for safe operation without hesitation or loss of time, and without ambiguity,
— designed so that the movement of the control is consistent with its effect,
— located outside the danger zones, except for certain controls where necessary, such as emergency stop, console for training of robots,
— positioned so that their operation cannot cause additional risk,
— designed or protected so that the desired effect, where a risk is involved, cannot occur without an intentional operation,
— made so as to withstand foreseeable strain; particular attention must be paid to emergency stop devices liable to be subjected to considerable strain.1.2.2. Органы управления
Органы управления должны быть:
- четко видны, хорошо различимы и, где это необходимо, иметь соответствующее обозначение;
- расположены так, чтобы ими можно было пользоваться без возникновения сомнений и потерь времени на выяснение их назначения;
- сконструированы так, чтобы перемещение органа управления согласовывалось с их воздействием;
- расположены вне опасных зон; исключение, где это необходимо, делается для определенных средств управления, таких, как средство экстренной остановки, пульт управления роботом;
- расположены так, чтобы их использование не вызывало дополнительных рисков;
- сконструированы или защищены так, чтобы в случаях, где возможно возникновение рисков, они не могли бы возникнуть без выполнения намеренных действий;
- сделаны так, чтобы выдерживать предполагаемую нагрузку; при этом особое внимание уделяется органам аварийного останова, которые могут подвергаться значительным нагрузкам.Where a control is designed and constructed to perform several different actions, namely where there is no one-to-one correspondence (e.g. keyboards, etc.), the action to be performed must be clearly displayed and subject to confirmation where necessary.
Если орган управления предназначен для выполнения разных действий, например, если в качестве органа управления используется клавиатура или аналогичное устройство, то должна выводиться четкая информация о предстоящем действии, и, если необходимо, должно выполняться подтверждение на выполнение такого действия.
Controls must be so arranged that their layout, travel and resistance to operation are compatible with the action to be performed, taking account of ergonomic principles.
Органы управления должны быть организованы таким образом, чтобы их расположение, перемещение их элементов и усилие, которое оператор затрачивает на их перемещение, соответствовали выполняемым операциям и принципам эргономики.
Constraints due to the necessary or foreseeable use of personal protection equipment (such as footwear, gloves, etc.) must be taken into account.
Необходимо учитывать скованность движений операторов при использовании необходимых или предусмотренных средств индивидуальной защиты (таких, как специальная обувь, перчатки и др.).
Machinery must be fitted with indicators (dials, signals, etc.) as required for safe operation. The operator must be able to read them from the control position.
Для обеспечения безопасной эксплуатации машинное оборудование должно быть оснащено индикаторами (циферблатами, устройствами сигнализации и т. д.). Оператор должен иметь возможность считывать их с места управления.
From the main control position the operator must be able to ensure that there are no exposed persons in the danger zones.
Находясь в главном пункте управления, оператор должен иметь возможность контролировать отсутствие незащищенных лиц.
If this is impossible, the control system must be designed and constructed so that an acoustic and/ or visual warning signal is given whenever the machinery is about to start.
Если это невозможно, то система управления должна быть разработана и изготовлена так, чтобы перед каждым пуском машинного оборудования подавался звуковой и/или световой предупредительный сигнал.
The exposed person must have the time and the means to take rapid action to prevent the machinery starting up.
[DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL]
Незащищенное лицо должно иметь достаточно времени и средств для быстрого предотвращения пуска машинного оборудования.
[Перевод Интент]
Тематики
- автоматизация, основные понятия
- аппарат, изделие, устройство...
- безопасность машин и труда в целом
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
- электробезопасность
- электротехника, основные понятия
Синонимы
EN
- actuating member
- actuator
- command unit
- control
- control device
- controller
- controls
- operating control
- operating means
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Betätigungsorgan
-
14 Verfassungsrecht
конституционное право
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
constitutional law
That branch of the public law of a nation or state which treats of the organization, powers and frame of government, the distribution of political and governmental authorities and functions, the fundamental principles which are to regulate the relations of government and citizen and which prescribes generally the plan and method according to which the public affairs of the nation or state are to be administered. (Source: BLACK)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Verfassungsrecht
-
15 unvorbereiteter Leiter
неподготовленный проводник
Проводник отрезанный и с удаленной изоляцией для вставки в вывод.
Примечание. К неподготовленным относятся проводники, форма которых изменена для вставки в вывод или жилы которых скручены для упрочнения конца
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
проводник, не подготовленный к присоединению
-
[IEV number 442-01-26]EN
unprepared conductor
conductor which has been cut and the insulation of which has been removed for insertion into a terminal
NOTE - A conductor, the shape of which is arranged for introduction into a terminal or the strands of which are twisted to consolidate the end is considered to be an unprepared conductor.
[IEC 61095, ed. 2.0 (2009-02)]
[IEV number 442-01-26]FR
conducteur non préparé
conducteur qui a été coupé et dont l'isolation a été retirée en vue de son insertion dans une borne
NOTE - Un conducteur dont la forme est arrangée pour qu'il soit dans une borne ou dont les torons sont torsadés pour en consolider l'extrémité est considéré comme un conducteur non préparé
[IEC 61095, ed. 2.0 (2009-02)]
[IEV number 442-01-26]

Проводник с удаленной изоляцией и с уплотненным концом многопроволочной жилы
Проводник с частично снятой (прорезанной) изоляцией
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > unvorbereiteter Leiter
-
16 Schadstoffsenke
поглотитель загрязнения
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
pollution sink
Vehicle for removal of a chemical or gas from the atmosphere-biosphere-ocean system, in which the substance is absorbed into a permanent or semi-permanent repository, or else transformed into another substance. A carbon sink, for example, might be the ocean (which absorbs and holds carbon from other parts of carbon cycle) or photosynthesis (which converts atmospheric carbon into plant material). Sinks are a fundamental factor in the ongoing balance which determines the concentration of every greenhouse gas in the atmosphere. If the sink is greater than the sources of a gas, its concentration in the atmosphere will decrease; if the source is greater than the sink, the concentration will increase. (Source: GLOCHA)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Schadstoffsenke
-
17 ununterbrochener Betrieb
продолжительный режим
Режим при котором главные контакты автоматического выключателя остаются замкнутыми, непрерывно проводя установившийся ток в течение длительного времени (неделями, месяцами или даже годами).
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
uninterrupted duty
duty in which the main contacts of a circuit-breaker remain closed whilst carrying a steady current without interruption for long periods (which could be weeks, months, or even years)
[IEC 60898-1, ed. 1.0 (2002-01)]FR
service ininterrompu
service dans lequel les contacts principaux d'un disjoncteur restent fermés tout en transportant un courant régulier sans interruption pendant de longues périodes (qui peuvent être des semaines, des mois, et même des années)
[IEC 60898-1, ed. 1.0 (2002-01)]Тематики
EN
DE
FR
непрерывный режим
длительный режим
-
[IEV number 442-05-43]EN
uninterrupted duty (for a switching device)
duty in which the main contacts of a switching device remain closed whilst carrying a steady current without interruption for long periods (which could be weeks, months, or even years)
[IEV number 442-05-43]FR
service ininterrompu (pour un dispositif de coupure)
service dans lequel les contacts principaux d'un dispositif de coupure restent fermés tout en transportant un courant permanent sans interruption pendant de longues périodes (qui peuvent être des semaines, des mois, et même des années)
[IEV number 442-05-43]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
Синонимы
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > ununterbrochener Betrieb
-
18 Prozessrecht
процессуальный закон
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
procedural law
Law which prescribes method of enforcing rights or obtaining redress for their invasion. Laws which fix duties, establish rights and responsibilities among and for persons, natural or otherwise, are "substantive laws" in character, while those which merely prescribe the manner in which such rights and responsibilities may be exercised and enforced in a court are "procedural laws". (Source: BLACK)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Prozessrecht
-
19 Rat der Europäischen Union
Совет ЕС
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
EU Council
The Council of the European Union is an institution which exercises legislative and decision-making powers. At the same time, it is the forum in which the representatives of the Governments of the 15 Member States can assert their interests and try to reach compromises. The Council ensures general coordination of the activities of the European Community, the main objective of which is the establishment of an internal market, i.e. an area without internal frontiers guaranteeing four freedoms of movement - for goods, persons, services and capital - to which should soon be added a single currency. In addition, the Council is responsible for intergovernmental cooperation, in common foreign and security policy (CFSP) and in the areas of justice and home affairs (JHA), including for example matters of immigration and asylum, combating terrorism and drugs and judicial cooperation. (Source: UEEU)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Rat der Europäischen Union
-
20 Leistungsschalter
автоматический выключатель
Механический коммутационный аппарат1), способный включать, проводить и отключать токи при нормальном состоянии электрической цепи, а также включать, проводить в течение заданного времени и автоматически отключать токи в указанном аномальном состоянии электрической цепи, например, при коротком замыкании.
(МЭС 441-14-20)
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]
автоматический выключатель
-
[IEV number 442-05-01]EN
circuit breaker
a mechanical switching device, capable of making, carrying and breaking currents under normal circuit conditions and also making, carrying for a specified time and breaking currents under specified abnormal circuit conditions such as those of short circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
circuit breaker
A device designed to open and close a circuit by nonautomatic means and to open the circuit automatically on a predetermined overcurrent without damage to itself when properly applied within its rating.
NOTE The automatic opening means can be integral, direct acting with the circuit breaker, or remote from the circuit breaker.
Adjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker can be set to trip at various values of current, time, or both within a predetermined range. Instantaneous-trip (as applied to circuit breakers). A qualifying term indicating that no delay is purposely introduced in the tripping action of the circuit breaker.
Inverse-time (as applied to circuit breakers). A qualifying term indicating a delay is purposely introduced in the tripping action of the circuit breaker, which delay decreases as the magnitude of the current increases.
Nonadjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker does not have any adjustment to alter the value of current at which it will trip or the time required for its operation.
Setting (of a circuit breaker). The value of current, time, or both at which an adjustable circuit breaker is set to trip.
[National Electrical Cod]FR
disjoncteur
1) Должно быть контактный коммутационный аппарат
appareil mécanique de connexion capable d’établir, de supporter et d’interrompre des courants dans les conditions normales du circuit, ainsi que d’établir, de supporter pendant une durée spécifiée et d’in- terrompre des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
[Интент]КЛАССИФИКАЦИЯ
- По роду тока
- По напряжению
- По числу полюсов
- По виду корпуса
- По месту установки
- По изолирующей среде
- По установленным расцепителям
- По дополнительным защитам
- По назначению
- По категории применения
- По виду привода взвода пружины
- По выполняемой функции
-
По влиянию монтажного положения
Автоматические выключатели ABB
Модульные автоматические выключатели
1. НЕКОТОРЫЕ СВЕДЕНИЯ ОБ АВТОМАТИЧЕСКИХ ВЫКЛЮЧАТЕЛЯХ Автоматический выключатель — это электрический аппарат, который автоматически отключает (и тем самым защищает) электрическую цепь при возникновении в ней аномального режима. Режим становится аномальным, когда в цепи начинает недопустимо изменяться (т. е. увеличиваться или уменьшаться относительно номинального значения) ток или напряжение.
Другими словами (более "инженерно") можно сказать, что автоматический выключатель защищает от токов короткого замыкания и токов перегрузки отходящую от него питающую линию, например, кабель и приемник(и) электрической энергии (осветительную сеть, розетки, электродвигатель и т. п.).
Как правило, автоматический выключатель может применятся также для нечастого (несколько раз в сутки) включения и отключения защищаемых электроприемников (защищаемой нагрузки).
[Интент]Выключатель предназначен для проведения тока в нормальном режиме и отключения тока при коротких замыканиях, перегрузках, недопустимых снижениях напряжения, а также до 30 оперативных включений и отключений электрических цепей в сутки и рассчитан для эксплуатации в электроустановках с номинальным рабочим напряжением до 660 В переменного тока частоты 50 и 60 Гц и до 440 В постоянного тока.
[Типовая фраза из российской технической документации] 2. ПРИНЦИП ДЕЙСТВИЯ Для защиты цепи от короткого замыкания применяется автоматический выключатель с электромагнитным расцепителем.
1 - Пружина (в данном случае во взведенном положении растянута)
Автоматический выключатель устроен таким образом, что сначала необходимо взвести пружину и только после этого его можно включить. У многих автоматических выключателей для взвода пружины необходимо перевести ручку вниз. После этого ручку переводят вверх. При этом замыкаются главные контакты.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Электромагнитный расцепитель;
5 - Сердечник
6 - Катушка
7 - Контактные зажимы автоматического выключателя
На рисунке показан один полюс автоматического выключателя во включенном положении: пружина 1 взведена, а главный контакт 2 замкнут.
Как только в защищаемой цепи возникнет короткое замыкание, ток, протекающий через соответствующий полюс автоматического выключателя, многократно возрастет. В катушке 6 сразу же возникнет сильное магнитное поле. Сердечник 5 втянется в катушку и освободит удерживающее устройство. Под действием пружины 1 главный контакт 2 разомкнется, в результате чего автоматический выключатель отключит и тем самым защитит цепь, в которой возникло короткое замыкание. Такое срабатывание автоматического выключателя происходит практически мгновенно (за сотые доли секунды).
Для защиты цепи от тока перегрузки применяют автоматические выключатели с тепловым расцепителем.
1 - Пружина (в данном случае во взведенном положении растянута)
Принцип действия такой же как и в первом случае, с той лишь разницей, что удерживающее устройство 3 освобождается под действием биметаллической пластины 5, которая изгибается от тепла, выделяемого нагревательным элементом 6. Количество тепла определяется током, протекающим через защищаемую цепь.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Тепловой расцепитель
5 - Биметаллическая пластина
6 - Нагревательный элемент
7 - Контактные зажимы автоматического выключателя
[Интент]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Обобщающие термины
Действия
- включение автоматического выключателя
- оперирование автоматического выключателя
- отключение автоматического выключателя
- срабатывание автоматического выключателя
EN
- auto-cutout
- automatic circuit breaker
- automatic cutout
- automatic switch
- breaker
- CB
- circuit breaker
- circuit-breaker
- cutout
DE
FR
Смотри также
силовой выключатель
-
[Интент]EN
circuit-breaker
a mechanical switching device, capable of making, carrying and breaking currents under normal circuit conditions and also making, carrying for a specified time and breaking currents under specified abnormal circuit conditions such as those of short circuit
[IEV ref 441-14-20]FR
disjoncteur
appareil mécanique de connexion capable d'établir, de supporter et d'interrompre des courants dans les conditions normales du circuit, ainsi que d'établir, de supporter pendant une durée spécifiée et d'interrompre des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit
[IEV ref 441-14-20]
Рис. Siemens
Силовой ( баковый элегазовый) выключатель 3AP1 DT
Рис. Siemens
Силовой (колонковый элегазовый) выключательТематики
- высоковольтный аппарат, оборудование...
- комплектное распред. устройство (КРУ)
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Leistungsschalter
См. также в других словарях:
Which — Which, pron. [OE. which, whilk, AS. hwilc, hwylc, hwelc, from the root of hw[=a] who + l[=i]c body; hence properly, of what sort or kind; akin to OS. hwilik which, OFries. hwelik, D. welk, G. welch, OHG. wel[=i]h, hwel[=i]h, Icel. hv[=i]l[=i]kr,… … The Collaborative International Dictionary of English
Which — which Unix утилита, отображающая полный путь к указанным командам или сценариям. Содержание 1 Описание 2 Опции 3 Пример использования … Википедия
Which — Voir « which » sur le Wiktionnaire … Wikipédia en Français
Which — is an English relative pronoun and interrogative pronoun.Which may also refer to: *Which?, a UK charity and its magazine *which (Unix), a Unix command See also * English relative clauses, for discussion of when to use which and when to use that… … Wikipedia
Which? — Infobox Magazine title = Which? image size = image caption = frequency = Monthly category = Consumer publisher = Which? firstdate = October 1957 country = flagcountry|United Kingdom language = English website = [http://www.which.co.uk… … Wikipedia
which — /hwich, wich/, pron. 1. what one?: Which of these do you want? Which do you want? 2. whichever: Choose which appeals to you. 3. (used relatively in restrictive and nonrestrictive clauses to represent a specified antecedent): The book, which I… … Universalium
which — I. adjective Etymology: Middle English, of what kind, which, from Old English hwilc; akin to Old High German wilīh of what kind, which, Old English hwā who, gelīk like more at who, like Date: before 12th century 1. being what one or ones out of a … New Collegiate Dictionary
Which? — a magazine produced each month by the Consumers’ Association in Britain. It consists of reports comparing different makes of similar products and services, to help people to decide which one to buy. It is only available to members of the… … Universalium
which — See: GAME AT WHICH TWO CAN PLAY … Dictionary of American idioms
which — See: GAME AT WHICH TWO CAN PLAY … Dictionary of American idioms
Which (Unix) — which Voir « which » sur le Wiktionnaire … Wikipédia en Français
Перевод: с немецкого на русский
- С немецкого на:
- Английский