-
1 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
2 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
3 temps de fermeture (d'ouverture) stable
время устойчивого замыкания (размыкания) контакта электрического реле
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
[ ГОСТ 16022-83]EN
time to stable closed condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is closed and fulfils specified requirements
[IEV number 446-17-24]
time to stable open condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is open and fulfils specified requirements
[IEV number 446-17-25]FR
temps de fermeture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est fermé et répond aux prescriptions spécifiées
[IEV number 446-17-24]
temps d'ouverture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est ouvert et répond aux prescriptions spécifiées
[IEV number 446-17-25]
Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > temps de fermeture (d'ouverture) stable
-
4 contact "a"
замыкающий контакт электрической цепи
Контакт электрической цепи, разомкнутый в начальном положении устройства и замыкающийся при переходе устройства в конечное положение
[ ГОСТ 14312-79]
контакт a - замыкающий контакт
Контакт управления или вспомогательный контакт, замкнутый, когда замкнуты главные контакты механического коммутационного аппарата, и разомкнутый, когда они разомкнуты.
МЭК 60050(441-15-12).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контакт «а»
замыкающий контакт
-
[IEV number 442-05-31]EN
make contact
a contact which is closed when the relay is in its operate condition and which is opened when the relay is in its release condition
[IEV number 446-16-15]
a-contact
make contact
a control or auxiliary contact which is closed when the main contacts of the circuit‑breaker or contactor are closed and open when they are open
Source: 441-15-12 MOD
[IEV number 442-05-31]FR
contact de travail
contact à fermeture
contact fermé lorsque le relais est à l'état de travail et ouvert lorsque le relais est à l'état de repos
[IEV number 446-16-15]
contact de fermeture
contact "a"
contact de commande ou contact auxiliaire qui est fermé lorsque les contacts principaux du disjoncteur ou du contacteur sont fermés et qui est ouvert lorsque ces contacts sont ouverts
Source: 441-15-12 MOD
[IEV number 442-05-31]Замыкающий контакт
(условное графическое обозначение)Недопустимые, нерекомендуемые
- Н.О. контакт
- нормально-открытый контакт
Тематики
Синонимы
- замыкающий контакт электрической цепи
- контакт «а»
EN
- a-contact
- circuit-closing contact
- closing contact
- form a relay
- form-a contact
- form-a relay
- make contact
- NO contact
- normally open contact
- normally-off contact
- open contact
- operating contact
DE
FR
Франко-русский словарь нормативно-технической терминологии > contact "a"
-
5 contact de fermeture
замыкающий контакт электрической цепи
Контакт электрической цепи, разомкнутый в начальном положении устройства и замыкающийся при переходе устройства в конечное положение
[ ГОСТ 14312-79]
контакт a - замыкающий контакт
Контакт управления или вспомогательный контакт, замкнутый, когда замкнуты главные контакты механического коммутационного аппарата, и разомкнутый, когда они разомкнуты.
МЭК 60050(441-15-12).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контакт «а»
замыкающий контакт
-
[IEV number 442-05-31]EN
make contact
a contact which is closed when the relay is in its operate condition and which is opened when the relay is in its release condition
[IEV number 446-16-15]
a-contact
make contact
a control or auxiliary contact which is closed when the main contacts of the circuit‑breaker or contactor are closed and open when they are open
Source: 441-15-12 MOD
[IEV number 442-05-31]FR
contact de travail
contact à fermeture
contact fermé lorsque le relais est à l'état de travail et ouvert lorsque le relais est à l'état de repos
[IEV number 446-16-15]
contact de fermeture
contact "a"
contact de commande ou contact auxiliaire qui est fermé lorsque les contacts principaux du disjoncteur ou du contacteur sont fermés et qui est ouvert lorsque ces contacts sont ouverts
Source: 441-15-12 MOD
[IEV number 442-05-31]Замыкающий контакт
(условное графическое обозначение)Недопустимые, нерекомендуемые
- Н.О. контакт
- нормально-открытый контакт
Тематики
Синонимы
- замыкающий контакт электрической цепи
- контакт «а»
EN
- a-contact
- circuit-closing contact
- closing contact
- form a relay
- form-a contact
- form-a relay
- make contact
- NO contact
- normally open contact
- normally-off contact
- open contact
- operating contact
DE
FR
Франко-русский словарь нормативно-технической терминологии > contact de fermeture
-
6 contact de travail
замыкающий контакт электрической цепи
Контакт электрической цепи, разомкнутый в начальном положении устройства и замыкающийся при переходе устройства в конечное положение
[ ГОСТ 14312-79]
контакт a - замыкающий контакт
Контакт управления или вспомогательный контакт, замкнутый, когда замкнуты главные контакты механического коммутационного аппарата, и разомкнутый, когда они разомкнуты.
МЭК 60050(441-15-12).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контакт «а»
замыкающий контакт
-
[IEV number 442-05-31]EN
make contact
a contact which is closed when the relay is in its operate condition and which is opened when the relay is in its release condition
[IEV number 446-16-15]
a-contact
make contact
a control or auxiliary contact which is closed when the main contacts of the circuit‑breaker or contactor are closed and open when they are open
Source: 441-15-12 MOD
[IEV number 442-05-31]FR
contact de travail
contact à fermeture
contact fermé lorsque le relais est à l'état de travail et ouvert lorsque le relais est à l'état de repos
[IEV number 446-16-15]
contact de fermeture
contact "a"
contact de commande ou contact auxiliaire qui est fermé lorsque les contacts principaux du disjoncteur ou du contacteur sont fermés et qui est ouvert lorsque ces contacts sont ouverts
Source: 441-15-12 MOD
[IEV number 442-05-31]Замыкающий контакт
(условное графическое обозначение)Недопустимые, нерекомендуемые
- Н.О. контакт
- нормально-открытый контакт
Тематики
Синонимы
- замыкающий контакт электрической цепи
- контакт «а»
EN
- a-contact
- circuit-closing contact
- closing contact
- form a relay
- form-a contact
- form-a relay
- make contact
- NO contact
- normally open contact
- normally-off contact
- open contact
- operating contact
DE
FR
Франко-русский словарь нормативно-технической терминологии > contact de travail
-
7 contact à fermeture
замыкающий контакт электрической цепи
Контакт электрической цепи, разомкнутый в начальном положении устройства и замыкающийся при переходе устройства в конечное положение
[ ГОСТ 14312-79]
контакт a - замыкающий контакт
Контакт управления или вспомогательный контакт, замкнутый, когда замкнуты главные контакты механического коммутационного аппарата, и разомкнутый, когда они разомкнуты.
МЭК 60050(441-15-12).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контакт «а»
замыкающий контакт
-
[IEV number 442-05-31]EN
make contact
a contact which is closed when the relay is in its operate condition and which is opened when the relay is in its release condition
[IEV number 446-16-15]
a-contact
make contact
a control or auxiliary contact which is closed when the main contacts of the circuit‑breaker or contactor are closed and open when they are open
Source: 441-15-12 MOD
[IEV number 442-05-31]FR
contact de travail
contact à fermeture
contact fermé lorsque le relais est à l'état de travail et ouvert lorsque le relais est à l'état de repos
[IEV number 446-16-15]
contact de fermeture
contact "a"
contact de commande ou contact auxiliaire qui est fermé lorsque les contacts principaux du disjoncteur ou du contacteur sont fermés et qui est ouvert lorsque ces contacts sont ouverts
Source: 441-15-12 MOD
[IEV number 442-05-31]Замыкающий контакт
(условное графическое обозначение)Недопустимые, нерекомендуемые
- Н.О. контакт
- нормально-открытый контакт
Тематики
Синонимы
- замыкающий контакт электрической цепи
- контакт «а»
EN
- a-contact
- circuit-closing contact
- closing contact
- form a relay
- form-a contact
- form-a relay
- make contact
- NO contact
- normally open contact
- normally-off contact
- open contact
- operating contact
DE
FR
Франко-русский словарь нормативно-технической терминологии > contact à fermeture
-
8 contact "b"
размыкающий контакт электрической цепи
Контакт электрической цепи, замкнутый в начальном положении устройства и размыкающийся при переходе устройства в конечное положение
[ ГОСТ 14312-79]
контакт b — размыкающий контакт
Контакт управления или вспомогательный контакт, разомкнутый, когда главные контакты контактного коммутационного аппарата замкнуты, и замкнутый, когда они разомкнуты.
МЭК 60050(441-15-13)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контакт «b»
размыкающий контакт
-
[IEV number 442-05-32]EN
break contact
a contact which is opened when the relay is in its operate condition and which is closed when the relay is in its release condition
[IEV number 446-16-16]
b-contact
break contact
a control or auxiliary contact which is open when the main contacts of the circuit-breaker or contactor are closed and closed when they are open
Source: 441-15-13 MOD
[IEV number 442-05-32]FR
contact de repos
contact à ouverture
contact ouvert lorsque le relais est à l'état de travail et fermé lorsque le relais est à l'état de repos
[IEV number 446-16-16]
contact d'ouverture
contact "b"
contact de commande ou contact auxiliaire qui est ouvert lorsque les contacts principaux du disjoncteur ou du contacteur sont fermés et qui est fermé lorsque ces contacts sont ouverts
Source: 441-15-13 MOD
[IEV number 442-05-32]Размыкающий контакт
(условное обозначение)This setting defines whether there is an intervention in the control process of external switchgear units by using external termination contacts.
[Schneider Electric]Данный параметр определяет возможность вмешательства в процесс управления внешними коммутационными аппаратами с помощью внешних размыкающих контактов.
[Перевод Интент]Недопустимые, нерекомендуемые
- Н.З. контакт
- нормально-закрытый контакт
Тематики
Обобщающие термины
Синонимы
- контакт «b»
- размыкающий контакт электрической цепи
EN
- "b" contact
- assistance switch b contact
- b contact
- b-contact
- BC
- break contact
- circuit-opening contact
- clearing contact
- cutoff contact
- form b relay
- form-b relay
- NC contact
- normally closed contact
- normally-on contact
- rest contact
- termination contact
DE
FR
- contact "b"
- contact d'ouverture
- contact de repos
- contact à ouverture
Франко-русский словарь нормативно-технической терминологии > contact "b"
-
9 contact d'ouverture
размыкающий контакт электрической цепи
Контакт электрической цепи, замкнутый в начальном положении устройства и размыкающийся при переходе устройства в конечное положение
[ ГОСТ 14312-79]
контакт b — размыкающий контакт
Контакт управления или вспомогательный контакт, разомкнутый, когда главные контакты контактного коммутационного аппарата замкнуты, и замкнутый, когда они разомкнуты.
МЭК 60050(441-15-13)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контакт «b»
размыкающий контакт
-
[IEV number 442-05-32]EN
break contact
a contact which is opened when the relay is in its operate condition and which is closed when the relay is in its release condition
[IEV number 446-16-16]
b-contact
break contact
a control or auxiliary contact which is open when the main contacts of the circuit-breaker or contactor are closed and closed when they are open
Source: 441-15-13 MOD
[IEV number 442-05-32]FR
contact de repos
contact à ouverture
contact ouvert lorsque le relais est à l'état de travail et fermé lorsque le relais est à l'état de repos
[IEV number 446-16-16]
contact d'ouverture
contact "b"
contact de commande ou contact auxiliaire qui est ouvert lorsque les contacts principaux du disjoncteur ou du contacteur sont fermés et qui est fermé lorsque ces contacts sont ouverts
Source: 441-15-13 MOD
[IEV number 442-05-32]Размыкающий контакт
(условное обозначение)This setting defines whether there is an intervention in the control process of external switchgear units by using external termination contacts.
[Schneider Electric]Данный параметр определяет возможность вмешательства в процесс управления внешними коммутационными аппаратами с помощью внешних размыкающих контактов.
[Перевод Интент]Недопустимые, нерекомендуемые
- Н.З. контакт
- нормально-закрытый контакт
Тематики
Обобщающие термины
Синонимы
- контакт «b»
- размыкающий контакт электрической цепи
EN
- "b" contact
- assistance switch b contact
- b contact
- b-contact
- BC
- break contact
- circuit-opening contact
- clearing contact
- cutoff contact
- form b relay
- form-b relay
- NC contact
- normally closed contact
- normally-on contact
- rest contact
- termination contact
DE
FR
- contact "b"
- contact d'ouverture
- contact de repos
- contact à ouverture
Франко-русский словарь нормативно-технической терминологии > contact d'ouverture
-
10 contact de repos
размыкающий контакт электрической цепи
Контакт электрической цепи, замкнутый в начальном положении устройства и размыкающийся при переходе устройства в конечное положение
[ ГОСТ 14312-79]
контакт b — размыкающий контакт
Контакт управления или вспомогательный контакт, разомкнутый, когда главные контакты контактного коммутационного аппарата замкнуты, и замкнутый, когда они разомкнуты.
МЭК 60050(441-15-13)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контакт «b»
размыкающий контакт
-
[IEV number 442-05-32]EN
break contact
a contact which is opened when the relay is in its operate condition and which is closed when the relay is in its release condition
[IEV number 446-16-16]
b-contact
break contact
a control or auxiliary contact which is open when the main contacts of the circuit-breaker or contactor are closed and closed when they are open
Source: 441-15-13 MOD
[IEV number 442-05-32]FR
contact de repos
contact à ouverture
contact ouvert lorsque le relais est à l'état de travail et fermé lorsque le relais est à l'état de repos
[IEV number 446-16-16]
contact d'ouverture
contact "b"
contact de commande ou contact auxiliaire qui est ouvert lorsque les contacts principaux du disjoncteur ou du contacteur sont fermés et qui est fermé lorsque ces contacts sont ouverts
Source: 441-15-13 MOD
[IEV number 442-05-32]Размыкающий контакт
(условное обозначение)This setting defines whether there is an intervention in the control process of external switchgear units by using external termination contacts.
[Schneider Electric]Данный параметр определяет возможность вмешательства в процесс управления внешними коммутационными аппаратами с помощью внешних размыкающих контактов.
[Перевод Интент]Недопустимые, нерекомендуемые
- Н.З. контакт
- нормально-закрытый контакт
Тематики
Обобщающие термины
Синонимы
- контакт «b»
- размыкающий контакт электрической цепи
EN
- "b" contact
- assistance switch b contact
- b contact
- b-contact
- BC
- break contact
- circuit-opening contact
- clearing contact
- cutoff contact
- form b relay
- form-b relay
- NC contact
- normally closed contact
- normally-on contact
- rest contact
- termination contact
DE
FR
- contact "b"
- contact d'ouverture
- contact de repos
- contact à ouverture
размыкающий магнитоуправляемый контакт
Магнитоуправляемый контакт, замкнутый в исходном положении и разомкнутый в рабочем положении
[ ГОСТ 17499-82]EN
FR
Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > contact de repos
-
11 contact à ouverture
размыкающий контакт электрической цепи
Контакт электрической цепи, замкнутый в начальном положении устройства и размыкающийся при переходе устройства в конечное положение
[ ГОСТ 14312-79]
контакт b — размыкающий контакт
Контакт управления или вспомогательный контакт, разомкнутый, когда главные контакты контактного коммутационного аппарата замкнуты, и замкнутый, когда они разомкнуты.
МЭК 60050(441-15-13)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
контакт «b»
размыкающий контакт
-
[IEV number 442-05-32]EN
break contact
a contact which is opened when the relay is in its operate condition and which is closed when the relay is in its release condition
[IEV number 446-16-16]
b-contact
break contact
a control or auxiliary contact which is open when the main contacts of the circuit-breaker or contactor are closed and closed when they are open
Source: 441-15-13 MOD
[IEV number 442-05-32]FR
contact de repos
contact à ouverture
contact ouvert lorsque le relais est à l'état de travail et fermé lorsque le relais est à l'état de repos
[IEV number 446-16-16]
contact d'ouverture
contact "b"
contact de commande ou contact auxiliaire qui est ouvert lorsque les contacts principaux du disjoncteur ou du contacteur sont fermés et qui est fermé lorsque ces contacts sont ouverts
Source: 441-15-13 MOD
[IEV number 442-05-32]Размыкающий контакт
(условное обозначение)This setting defines whether there is an intervention in the control process of external switchgear units by using external termination contacts.
[Schneider Electric]Данный параметр определяет возможность вмешательства в процесс управления внешними коммутационными аппаратами с помощью внешних размыкающих контактов.
[Перевод Интент]Недопустимые, нерекомендуемые
- Н.З. контакт
- нормально-закрытый контакт
Тематики
Обобщающие термины
Синонимы
- контакт «b»
- размыкающий контакт электрической цепи
EN
- "b" contact
- assistance switch b contact
- b contact
- b-contact
- BC
- break contact
- circuit-opening contact
- clearing contact
- cutoff contact
- form b relay
- form-b relay
- NC contact
- normally closed contact
- normally-on contact
- rest contact
- termination contact
DE
FR
- contact "b"
- contact d'ouverture
- contact de repos
- contact à ouverture
размыкающий магнитоуправляемый контакт
Магнитоуправляемый контакт, замкнутый в исходном положении и разомкнутый в рабочем положении
[ ГОСТ 17499-82]EN
FR
Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > contact à ouverture
-
12 hors-jeu
Position d'un joueur qui, au moment où le ballon est touché par un coéquipier, est plus près de la ligne de but adverse que le ballon et l'avant-dernier joueur adverse.► Etre en position de hors-jeu n'est une infraction que si le joueur en position de hors-jeu prend une part active au jeu, auquel cas l' arbitre accorde à l' équipe adverse un coup franc indirect.
♦ Etre en position de hors-jeu; se trouver en position de hors-jeu; tirer avantage d'une position de hors-jeu; sanctionner une position de hors-jeu.Syn. hors-jeu mPosition in which a player is nearer to the opposing team's goal line than both the ball and the second last opposing player at the moment when the ball is played by another player of his own team.► An offside position is only considered as an offence when the player in the offside position is involved in active play at the moment when the ball touches or is being played by one of his team, in which case the referee awards the opposing team an indirect free kick.
♦ To be in an offside position. -
13 position de hors-jeu
Position d'un joueur qui, au moment où le ballon est touché par un coéquipier, est plus près de la ligne de but adverse que le ballon et l'avant-dernier joueur adverse.► Etre en position de hors-jeu n'est une infraction que si le joueur en position de hors-jeu prend une part active au jeu, auquel cas l' arbitre accorde à l' équipe adverse un coup franc indirect.
♦ Etre en position de hors-jeu; se trouver en position de hors-jeu; tirer avantage d'une position de hors-jeu; sanctionner une position de hors-jeu.Syn. hors-jeu mPosition in which a player is nearer to the opposing team's goal line than both the ball and the second last opposing player at the moment when the ball is played by another player of his own team.► An offside position is only considered as an offence when the player in the offside position is involved in active play at the moment when the ball touches or is being played by one of his team, in which case the referee awards the opposing team an indirect free kick.
♦ To be in an offside position.Dictionnaire Français-Anglais (UEFA Football) > position de hors-jeu
-
14 interrupteur de défaut
аварийный выключатель
Вспомогательный выключатель, срабатывающий только при отключении1) автоматического выключателя, с которым он связан.
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]EN
alarm switch
an auxiliary switch which operates only upon the tripping of the circuit-breaker with which it is associated
[IEC 60947-2, ed. 4.0 (2006-05)]FR
interrupteur de défaut
interrupteur auxiliaire ne fonctionnant que lors du déclenchement du disjoncteur auquel il est associé
[IEC 60947-2, ed. 4.0 (2006-05)]
1) Должно быть "при срабатывании". При ручном отключении автоматического выключателя аварийный выключатель не срабатывает.
[Интент]
Параллельные тексты EN-RU
Диаграмма состояния контакта сигнализации AX
Контакт имеет два положения: одно положение - в положении автоматического выключателя ВКЛ. (ON) и ОТКЛ. (OFF); второе положение - в положениях автоматического выключателя СРАБОТАЛ (TRIP).
Рис. LS Industrial SystemsAlarm switches offer provisions for immediate audio or visual indication of a tripped breaker due to overload, short-circuit, operation of shunt trip, or undervoltage trip conditions, operation of push button.
They are particularly useful in automated plants where operators must be signaled about changes in the electrical distribution system.
This switch features a closed contact when the circuit breaker is tripped automatically.
In other words, this switch does not function when the breaker is operated manually.
Its contact is open when the circuit breaker is reset.
[LS Industrial Systems]Контакт сигнализации предназначен для реализации звуковой или световой сигнализации срабатывания автоматического выключателя, произошедшей вследствие перегрузки, короткого замыкания, срабатывания минимального расцепителя напряжения, независимого расцепителя или при нажатии кнопки ПРОВЕРКА.
Такие контакты часто применяют в автоматизированных электроустановках, операторы которых должны контролировать изменения, происходящие в системе распределения электроэнергии.
Данный контакт замыкается только при срабатывании автоматического выключателя.
Другими словами, контакт сигнализации не изменяет своего состояния при ручном включении или отключении автоматического выключателя.
Контакт сигнализации размыкается при переводе автоматического выключателя из положения СРАБОТАЛ в положение ОТКЛЮЧЕН.
[Перевод Интент]
В низковольтных автоматических выключателеях аварийный выключатель (контакт сигнализации) является дополнительной принадлежностью, которая встраивается в гнездо автоматического выключателя
Дополнительные (электрические) принадлежности, встраиваемые в специальные гнезда автоматического выключателя:
1 - Левое гнездо;
2 - Автоматический выключатель;
3 - Правое гнездо.
Рис. LS Industrial SystemsТематики
Классификация
>>>Синонимы
EN
- AL
- alarm switch
FR
Франко-русский словарь нормативно-технической терминологии > interrupteur de défaut
-
15 érosion par l'eau
водная эрозия
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
water erosion
The breakdown of solid rock into smaller particles and its removal by water. As weathering, erosion is a natural geological process, but more rapid soil erosion results from poor land-use practices, leading to the loss of fertile topsoil and to the silting of dams, lakes, rivers and harbours. There are three classes of erosion by water. a) Splash erosion occurs when raindrops strike bare soil, causing it to splash, as mud, to flow into spaces in the soil and to turn the upper layer of soil into a structureless, compacted mass that dries with a hard, largely impermeable crust. b) Surface flow occurs when soil is removed with surface run-off during heavy rain. c) Channelized flow occurs when a flowing mixture of water and soil cuts a channel, which is then deepened by further scouring. A minor erosion channel is called a rill, a larger channel a gully. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > érosion par l'eau
-
16 déclencheur à manque de tension
минимальный расцепитель напряжения
Расцепитель, автоматически срабатывающий, когда подаваемое напряжение опускается ниже заданного уровня.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]
минимальное реле или минимальной расцепитель напряжения
Реле или расцепитель, допускающие размыкание или замыкание контактного коммутационного аппарата с выдержкой времени или без нее, когда напряжение на выводах этого реле или расцепителя падает ниже заданной величины
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
under-voltage release
a shunt release which permits a mechanical switching device to open or close, with or without time-delay, when the voltage across the terminals of the release falls below a predetermined value.
[IEC 62271-100, ed. 2.0 (2008-04)
undervoltage release
release which causes a CBE to open, with or without delay, when the voltage across the terminals of the release falls below a predetermined value
[IEC 60934, ed. 3.0 (2000-10)]FR
déclencheur à minimum de tension
déclencheur shunt qui permet l’ouverture ou la fermeture, avec ou sans retard, d’un appareil mécanique de connexion lorsque la tension aux bornes du déclencheur tombe au-dessous d’une valeur prédéterminée.
[IEC 62271-100, ed. 2.0 (2008-04)]
déclencheur à manque de tension
déclencheur qui provoque l'ouverture du DPE avec ou sans retard, lorsque la tension aux bornes du déclencheur tombe au-dessous d'une valeur prédéterminée
[IEC 60934, ed. 3.0 (2000-10)]
Параллельные тексты EN-RU
The undervoltage trip automatically opens a circuit breaker when voltage drops to a value ranging between 35% to 70% of the line voltage.
The operation is instantaneous, and the circuit breaker cannot be reclosed until the voltage returns to 85% of line voltage.
Continuously energized, the undervoltage trip must be operating before the circuit breaker can be closed.
[LS Industrial Systems]Минимальный расцепитель напряжения вызывает срабатывание автоматического выключателя, если линейное напряжение защищаемой цепи падает до 35-70 % от номинального значения.
Срабатывание происходит мгновенно, после чего автоматический выключатель невозможно перевести во включенное положение до тех, пока линейное напряжение защищаемой цепи не повысится до 85 %.
Минимальный расцепитель постоянно находится под напряжением защищаемой цепи и всегда успевает сработать до того, как будет предпринята попытка включения автоматического выключателя.
[Перевод Интент]
В низковольтных автоматических выключателеях минимальный расцепитель напряжения является дополнительной принадлежностью, которая встраивается в гнездо автоматического выключателя
Дополнительные (электрические) принадлежности, встраиваемые в специальные гнезда автоматического выключателя:
1 - Левое гнездо;
2 - Автоматический выключатель;
3 - Правое гнездо.
Рис. LS Industrial SystemsНедопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
- low-voltage release
- under voltage release
- under voltage trip
- under voltage trip coil
- under voltage trip device
- under voltage trip unit
- undervoltage release
- undervoltage trip
- undervoltage trip device
- undervoltage trip unit
- UVT
FR
Франко-русский словарь нормативно-технической терминологии > déclencheur à manque de tension
-
17 déclencheur à minimum de tension
минимальный расцепитель напряжения
Расцепитель, автоматически срабатывающий, когда подаваемое напряжение опускается ниже заданного уровня.
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]
минимальное реле или минимальной расцепитель напряжения
Реле или расцепитель, допускающие размыкание или замыкание контактного коммутационного аппарата с выдержкой времени или без нее, когда напряжение на выводах этого реле или расцепителя падает ниже заданной величины
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
under-voltage release
a shunt release which permits a mechanical switching device to open or close, with or without time-delay, when the voltage across the terminals of the release falls below a predetermined value.
[IEC 62271-100, ed. 2.0 (2008-04)
undervoltage release
release which causes a CBE to open, with or without delay, when the voltage across the terminals of the release falls below a predetermined value
[IEC 60934, ed. 3.0 (2000-10)]FR
déclencheur à minimum de tension
déclencheur shunt qui permet l’ouverture ou la fermeture, avec ou sans retard, d’un appareil mécanique de connexion lorsque la tension aux bornes du déclencheur tombe au-dessous d’une valeur prédéterminée.
[IEC 62271-100, ed. 2.0 (2008-04)]
déclencheur à manque de tension
déclencheur qui provoque l'ouverture du DPE avec ou sans retard, lorsque la tension aux bornes du déclencheur tombe au-dessous d'une valeur prédéterminée
[IEC 60934, ed. 3.0 (2000-10)]
Параллельные тексты EN-RU
The undervoltage trip automatically opens a circuit breaker when voltage drops to a value ranging between 35% to 70% of the line voltage.
The operation is instantaneous, and the circuit breaker cannot be reclosed until the voltage returns to 85% of line voltage.
Continuously energized, the undervoltage trip must be operating before the circuit breaker can be closed.
[LS Industrial Systems]Минимальный расцепитель напряжения вызывает срабатывание автоматического выключателя, если линейное напряжение защищаемой цепи падает до 35-70 % от номинального значения.
Срабатывание происходит мгновенно, после чего автоматический выключатель невозможно перевести во включенное положение до тех, пока линейное напряжение защищаемой цепи не повысится до 85 %.
Минимальный расцепитель постоянно находится под напряжением защищаемой цепи и всегда успевает сработать до того, как будет предпринята попытка включения автоматического выключателя.
[Перевод Интент]
В низковольтных автоматических выключателеях минимальный расцепитель напряжения является дополнительной принадлежностью, которая встраивается в гнездо автоматического выключателя
Дополнительные (электрические) принадлежности, встраиваемые в специальные гнезда автоматического выключателя:
1 - Левое гнездо;
2 - Автоматический выключатель;
3 - Правое гнездо.
Рис. LS Industrial SystemsНедопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
- low-voltage release
- under voltage release
- under voltage trip
- under voltage trip coil
- under voltage trip device
- under voltage trip unit
- undervoltage release
- undervoltage trip
- undervoltage trip device
- undervoltage trip unit
- UVT
FR
Франко-русский словарь нормативно-технической терминологии > déclencheur à minimum de tension
-
18 prolifération d'algues
рост водорослей
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
algal bloom
Excessive and rapid growth of algae and other aquatic plants when they are stimulated to grow too quickly by pollution. It takes place when there are too many nutrients in the water and is aggravated when accompanied by a rise in temperature. Although the algae grow quickly they soon die because they have swallowed up all the water's nutrients. As they decompose they tend to rise to the surface and form a green slime. Algal bloom have increased because higher levels of nitrogen and phosphates from agricultural areas have leached from the fields into water courses. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > prolifération d'algues
-
19 procédure de remplacement
Procédure à laquelle il faut se conformer lors du remplacement d'un joueur par un joueur remplaçant, selon laquelle ce dernier n'a le droit de pénétrer sur le terrain de jeu que sur un signe de l' arbitre et qu'après la sortie du joueur qu'il doit remplacer.Procedure to be observed in order to replace a player during a match, when the substitute player may only enter the field of play when permitted to do so by the referee and once the player being replaced has left the field.Dictionnaire Français-Anglais (UEFA Football) > procédure de remplacement
-
20 verrou
Système défensif, développé par la Suisse dans les années 1930, qui se caractérise par la présence d'un quatrième défenseur en retrait des trois autres, libéré de tout marquage, verrouillant ainsi la défense.► Système rendu célèbre par l'entraîneur autrichien Karl Rappan.
Syn. verrou Rappan m, verrou mTeam tactical system developed by Switzerland in the 1930s in which all players move forward when on the attack but all fall back in defence when the opposing team counter-attacks, the forwards attempting to confront this counter-attack at the halfway line.► The bolt was introduced by the Austrian Karl Rappan who was player-manager of Servette Geneva in 1932 and later went on to become Swiss national coach.
См. также в других словарях:
when — [ wen, hwen ] function word *** When can be used in the following ways: as a conjunction (connecting two clauses): When he saw me, he waved. as a question adverb (introducing a direct or indirect question): When should we meet? Do you know when… … Usage of the words and phrases in modern English
when — W1S1 [wen] adv, conj, pron [: Old English; Origin: hwanne, hwenne] 1.) at what time ▪ When are we leaving? ▪ When did you first meet Dr Darnall? ▪ When will the work be finished? ▪ I don t know when I ll see her again. when to do sth ▪ I ll tell… … Dictionary of contemporary English
When — When, adv. [OE. when, whan, whenne, whanne, AS. hw[ae]nne, hwanne, hwonne; akin to OS. hwan, OD. wan, OHG. wanne, G. wann when, wenn if, when, Goth. hwan when, and to E. who. ????. See {Who}.] [1913 Webster] 1. At what time; used interrogatively … The Collaborative International Dictionary of English
When as — When When, adv. [OE. when, whan, whenne, whanne, AS. hw[ae]nne, hwanne, hwonne; akin to OS. hwan, OD. wan, OHG. wanne, G. wann when, wenn if, when, Goth. hwan when, and to E. who. ????. See {Who}.] [1913 Webster] 1. At what time; used… … The Collaborative International Dictionary of English
when — [hwen, wen] adv. [ME whenne < OE hwænne, akin to Ger wann, when, wenn, if, akin to hwa, who: see WHAT] 1. a) at what time? [when did they leave? he asked when he should go] b) on what occasion or under what circumstances? [when do you double… … English World dictionary
When — may refer to:* When?, one of the Five Ws, questions used in journalism * WHEN, a sports radio station in Syracuse once affiliated with WTVH * WHEN, the former call letters of TV station WTVH in Syracuse, New York, U.S.In music: * When (1958 song) … Wikipedia
When — Saltar a navegación, búsqueda «When» Sencillo de Shania Twain del álbum Come on Over Publicación 1 de junio de 1998 (Reino Unido) Formato Radio Single Maxi Single … Wikipedia Español
when — when·as; when·ness; when·som·ev·er; when; when·ev·er; when·so·ev·er; … English syllables
When I Go — may refer to: * When I Go , a song by Screaming Jets from their 1997 album World Gone Crazy * When I Go (album), a 1998 album by Dave Carter and Tracy Grammer … Wikipedia
when — O.E. hwænne, hwenne, hwonne, from Gmc. pronomial stem *khwa (Cf. O.S. hwan, O.Fris. hwenne, M.Du. wan, O.H.G. hwanne, Ger. wann when ), from PIE interrogative base *qwo (see WHO (Cf. who)) … Etymology dictionary
when|as — «hwehn AZ, hwuhn », conjunction. Archaic. when; while; whereas … Useful english dictionary