-
81 function Ac
функция Ac (реле времени)
- Отсчет двух выдержек времени: после подачи и после снятия напряжения с управляющего входа.
- Задержка срабатывания и задержка возврата реле после подачи и после снятия напряжения с управляющего входа.
[Интент]EN
function Ac
Timing after closing and opening of control contact
[Crouzed]
function Ac
On-delay and off-delay relay with control signal
[Schneider Electric]
Рис. CrouzedПараллельные тексты EN-RU
After energisation, closure of the control contact causes the timing period T to commence and output relay R (or the load) changes state at the end of this interval.
When contact C (Y1) opens, relay R resets after a second timing period T.
[Crouzed]После подачи питания на реле и последующего замыкания контакта в цепи управляющего входа выполняется отсчет выдержки времени Т, по окончании которого выходное реле R (или нагрузка) изменяет свое состояние.
После размыкания контакта С еще раз отсчитывается выдержка времени Т, по окончании которой реле R возвращается в исходное состояние.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Ac
-
82 function H
функция H (реле времени)
Формирование импульса после включения питания реле
[Интент]EN
function H
Interval relay
[Schneider Electric]
function H
Timing on energisation
Interval timer - one shot
[Crouzet]Параллельные тексты EN-RU
Function H
Interval relay
On energization of the relay, timing period T starts and the output(s) R close(s).
At the end of the timing period T, output(s) R revert(s) to its/their initial state.
[Schneider Electric]Функция H
Формирование импульса после включения питания реле
При подаче питания на реле времени начинается отсчет выдержки T и замыкае(ю)тся выход(ы) R.
По окончании выдержки T выход(ы) R возвращае(ю)тся в исходное положение.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function H
-
83 function Ad
функция Ad (реле времени)
Задержка срабатывания и мгновенный возврат реле после каждой подачи напряжения на управляющий вход.
[Интент]EN
function Ad
Pulse delayed relay with control signal
[Schneider Electric]
function Ad
Delay on energisation by switch (not resettable)
[Crouzed]Параллельные тексты EN-RU
Function Ad
Pulse delayed relay with control signal
After power-up, pulsing or maintaining control contact C starts the timing T.
At the end of this timing period T, the output R closes.
The output R will be reset the next time control contact C is pulsed or maintained.
[Schneider Electric]
Function Ad
Delay on energisation by switch (not resettable)
After power-up, pressing or holding down the switch starts timing. At the end of timing, the output is energised.
The output will be reset the next time the switch is pressed or held down.
[Crouzed]Функция Ad
Задержка срабатывания и мгновенный возврат реле после каждой подачи напряжения на управляющий вход
После подачи питания на реле и последующей подачи импульса или постоянно напряжения на управляющий вход начинается отсчет выдержки времени T, по окончании которой выход реле R замыкается.
При следующей подаче импульса или постоянно напряжения на управляющий вход выход реле R возвращается в исходное состояние.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Ad
-
84 circuit
1) схема; цепь; контур2) эл. сеть4) шлейф ( в телефонии)•to track circuits — сопрягать контуры-
in-line hydraulic circuit
-
tee-test hydraulic circuit
-
absorption circuit
-
ac circuit
-
active circuit
-
adapter circuit
-
adder circuit
-
addressing circuit
-
aerial circuit
-
aerodrome circuit
-
aerodrome taxi circuit
-
aerodrome traffic circuit
-
aeromagnetic circuit
-
alarm circuit
-
alive circuit
-
amplifying circuit
-
analogous circuit
-
analog circuit
-
ancillary circuit
-
AND circuit
-
AND-to-OR circuit
-
AND-OR circuit
-
anticoincidence circuit
-
antihunt circuit
-
antireciprocal circuit
-
antiresonance circuit
-
antiresonant circuit
-
aperiodic circuit
-
approach circuit
-
astable circuit
-
autodyne circuit
-
automatic frequency control circuit
-
automatic reciprocation pneumatic circuit
-
auxiliary circuit
-
auxiliary coolant circuit
-
averaging circuit
-
back-to-back circuit
-
balanced circuit
-
balancing circuit
-
bias and erase circuit
-
bias circuit
-
bidirectional hydraulic motor circuit
-
bipolar circuit
-
bistable circuit
-
black-level restoring circuit
-
blanking circuit
-
blasting circuit
-
blocking circuit
-
booster hydraulic circuit
-
bound circuit
-
boxcar circuit
-
brake retraction circuit
-
branched circuit
-
branch circuit
-
breadboard circuit
-
break circuit
-
bridge circuit
-
bridged circuit
-
broken circuit
-
bubble circuit
-
bucket-brigade circuit
-
buffer circuit
-
burst-gating circuit
-
calibrating circuit
-
call circuit
-
carrier recovery circuit
-
cascode circuit
-
cavity circuit
-
charge circuit
-
charge-coupied device circuit
-
charging circuit
-
checkout circuit
-
cholesteric circuit
-
chopping circuit
-
chromatic circuit
-
circulating lubrication circuit
-
clamp circuit
-
cleaning circuit
-
clearing circuit
-
clipping circuit
-
clocked circuit
-
closed circuit
-
close circuit
-
closed loop circuit
-
closed loop hydraulic motor circuit
-
coaxial circuit
-
code track circuit
-
coincidence circuit
-
color-killer circuit
-
color-processing circuit
-
combination air-oil circuit
-
combinational circuit
-
common-base circuit
-
common-collector circuit
-
common-drain circuit
-
common-emitter circuit
-
common-gate circuit
-
common-source circuit
-
communication circuit
-
comparator circuit
-
compensating circuit
-
complementary circuit
-
completed circuit
-
composite circuit
-
condensate circuit
-
control circuit
-
convergence circuit
-
coolant circuit
-
cooling short circuit
-
cord circuit
-
correcting circuit
-
counter circuit
-
coupled circuits
-
cross rectifier circuit
-
crushing circuit
-
current circuit
-
current-feedback circuit
-
current-limiting circuit
-
current-limit circuit
-
damping circuit
-
Danington circuit
-
dc circuit
-
dead circuit
-
decision making circuit
-
decision circuit
-
decoding circuit
-
decoupling circuit
-
dedicated circuit
-
de-emphasis circuit
-
degaussing circuit
-
degenerative circuit
-
delay circuit
-
delta circuit
-
derived circuit
-
detecting circuit
-
detuned circuit
-
dial toll circuit
-
dial-up circuit
-
differentiating circuit
-
digital circuit
-
diplex circuit
-
direct circuit
-
direct speech circuit
-
discharge circuit
-
distributed-element circuit
-
dividing circuit
-
double-rail track circuit
-
drive circuit
-
driver circuit
-
dual circuit
-
dual-relief braking hydraulic motor circuit
-
duplex circuit
-
dynamic braking circuit
-
earthed circuit
-
earth circuit
-
edge-activated circuit
-
electric circuit
-
electrical safety circuit
-
electrolysis circuit
-
electronic circuit
-
emphasis circuit
-
enabling circuit
-
energized circuit
-
engineering circuit
-
enhancement circuit
-
equilization circuit
-
equivalent circuit
-
error correcting circuit
-
evaporating circuit
-
exciting circuit
-
exclusive OR circuit
-
exposure control circuit
-
exposure measuring circuit
-
external circuit
-
external load circuit
-
fallback circuit
-
feed circuit
-
feed motor circuit
-
feedback circuit
-
feedrate override circuit
-
filament circuit
-
filter hydraulic circuit
-
firing circuit
-
flip-flop circuit
-
flotation circuit
-
flow circuit
-
fluid circuit
-
forked circuit
-
four-terminal circuit
-
four-wire circuit
-
frame-scanning circuit
-
free-running circuit
-
frequency determining circuit
-
frequency-changing circuit
-
full-wave circuit
-
gain circuit
-
gas circuit
-
gate circuit
-
grinding circuit
-
ground short circuit
-
grounded circuit
-
ground circuit
-
half-duplex circuit
-
half-phantom circuit
-
half-wave circuit
-
half-wave track circuit
-
heat transport main circuit
-
heater circuit
-
holding circuit
-
horizontal scanning circuit
-
hotline circuit
-
hybrid-type circuit
-
hybrid circuit
-
hydraulic circuit
-
hydraulic servo circuit
-
identification circuit
-
idler circuit
-
ignition circuit
-
ignition primary circuit
-
ignition secondary circuit
-
impulse circuit
-
impulsing circuit
-
incoming track circuit
-
inductive circuit
-
inhibit circuit
-
input circuit
-
insulated circuit
-
integrated circuit
-
integrating circuit
-
intentional short circuit
-
interface circuit
-
interlocking circuit
-
interlock circuit
-
international television circuit
-
inverter circuit
-
invert circuit
-
iron circuit
-
jointless pulse track circuit
-
junction circuit
-
keep-alive circuit
-
ladder circuit
-
lagging circuit
-
latching circuit
-
LC circuit
-
leakage circuit
-
leak circuit
-
leased circuit
-
level circuit
-
linear circuit
-
linearizing circuit
-
line-scanning circuit
-
line-to-ground short circuit
-
live circuit
-
load circuit
-
locking circuit
-
locking hydraulic circuit
-
locking track circuit
-
logic circuit
-
long-distance transmission circuit
-
loop circuit
-
low-loss circuit
-
lumped-element lumped-parameter circuit
-
lumped lumped-parameter circuit
-
lumped-element circuit
-
lumped circuit
-
magnetic circuit
-
magnetic-core circuit
-
main circuit
-
majority circuit
-
make circuit
-
matching circuit
-
match circuit
-
matrix circuit
-
maximum power control circuit
-
measuring circuit
-
memory circuit
-
mesh circuit
-
metallic circuit
-
meter-current circuit
-
metering circuit
-
meter-voltage circuit
-
microelectronic circuit
-
microwave circuit
-
molecular circuit
-
monitoring circuit
-
monostable circuit
-
motor control circuit
-
multidrop circuit
-
multiplication circuit
-
multipoint circuit
-
multistable circuit
-
multistage circuit
-
muting circuit
-
NAND circuit
-
narrowband circuit
-
network circuit
-
neutral track circuit
-
neutralizing circuit
-
noise-balancing circuit
-
noninductive circuit
-
NOR circuit
-
NOT circuit
-
NOT-AND circuit
-
NOT-OR circuit
-
offset compensating circuit
-
one-pole circuit
-
one-rail track circuit
-
one-wire circuit
-
open circuit
-
open loop circuit
-
open-wire circuit
-
OR circuit
-
order wire circuit
-
OR-ELSE circuit
-
oscillating circuit
-
oscillation circuit
-
oscillatory circuit
-
output circuit
-
overflux circuit
-
overhead circuit
-
packaged circuit
-
paging circuit
-
parallel circuit
-
parallel-resonant circuit
-
parallel-series circuit
-
passive circuit
-
peak white-limiting circuit
-
peaking circuit
-
phantom circuit
-
phase switching circuit
-
phase-comparison circuit
-
phase-compensating circuit
-
phase-equalizing circuit
-
phase-inverting circuit
-
phase-sensitive track circuit
-
phase-shifting circuit
-
phase-shift circuit
-
pilot circuit
-
pneumatic circuit
-
points control circuit
-
points track circuit
-
point-to-point circuit
-
polarity circuit
-
polarized track circuit
-
polling circuit
-
polyphase circuit
-
potential circuit
-
power circuit
-
precharge circuit
-
precision timing circuit
-
pressure control hydraulic circuit
-
primary circuit
-
primary coolant circuit
-
printed circuit
-
protection circuit
-
pulse circuit
-
pulse-shaping circuit
-
pump unloading hydraulic circuit
-
pumping circuit
-
pump circuit
-
push-pull circuit
-
push-to-type circuit
-
quadruplex circuit
-
radiation-hardened circuit
-
radio communication circuit
-
radio circuit
-
RC circuit
-
reaction circuit
-
reaction track circuit
-
reactive circuit
-
reclosing circuit
-
rectification circuit
-
reference circuit
-
reflex circuit
-
regenerative circuit
-
register mark recognition circuit
-
regrinding circuit
-
regulating circuit
-
rejector circuit
-
relay circuit
-
relay contact switching circuit
-
relay contact circuit
-
remote-ring circuit
-
replenishing hydraulic motor circuit
-
reset circuit
-
resonance circuit
-
retaining circuit
-
return circuit
-
ring circuit
-
ringing circuit
-
route locking circuit
-
sample circuit
-
sample-and-hold circuit
-
sampler circuit
-
scaling circuit
-
scanning circuit
-
schematic circuit
-
screening circuit
-
secondary circuit
-
secondary coolant circuit
-
selecting circuit
-
selection circuit
-
self-bias circuit
-
self-checking circuit
-
self-holding circuit
-
self-test circuit
-
semiconductor circuit
-
separation circuit
-
sequencing circuit
-
series circuit
-
series-resonant circuit
-
series-tuned circuit
-
service circuit
-
shell circuit
-
shifting circuit
-
short circuit
-
shunt circuit
-
shutoff circuit
-
signal circuit
-
signaling circuit
-
simplex circuit
-
single-phase circuit
-
single-rail track circuit
-
single-wire circuit
-
slow-wave circuit
-
smoothing circuit
-
sneak circuit
-
solid-state circuit
-
solid circuit
-
spare circuit
-
speaker circuit
-
speed regulating circuit
-
squelch circuit
-
standby circuit
-
star-connected circuit
-
starting circuit
-
station conventional track circuit
-
steady energy track circuit
-
stripline circuit
-
strip circuit
-
subcarrier recovery circuit
-
subtransmission circuit
-
superconducting circuit
-
supply circuit
-
suppression circuit
-
sustained short circuit
-
sweep circuit
-
switched circuit
-
switching circuit
-
symbolic circuit
-
symmetrical circuit
-
symmetric circuit
-
synchronization circuit
-
synchronizing hydraulic circuit
-
synchronous circuit
-
table circuit
-
tank circuit
-
tap circuit
-
tapped circuit
-
T-circuit
-
telegraph circuit
-
telephone circuit
-
temperature stabilized circuit
-
tension sensing circuit
-
terminal circuit
-
test circuit
-
thickening circuit
-
three-phase circuit
-
threshold circuit
-
throttled circuit
-
through circuit
-
tilt kickout hydraulic circuit
-
time-base circuit
-
time-delay circuit
-
timer circuit
-
time-slot assigner circuit
-
timing circuit
-
toll circuit
-
tool selector circuit
-
toroidal magnetic circuit
-
touch sensing circuit
-
track circuit
-
train dispatching circuit
-
transient short circuit
-
transmission hydraulic circuit
-
trap circuit
-
tree circuit
-
triggering circuit
-
trigger circuit
-
trouble-detecting circuit
-
trunk circuit
-
tube circuit
-
tuned circuit
-
two-port circuit
-
two-state circuit
-
two-terminal circuit
-
two-wire circuit
-
unbalanced circuit
-
unidirectional hydraulic motor circuit
-
unipolar circuit
-
vertical-scanning circuit
-
virtual circuit
-
voltage-feedback circuit
-
warning circuit
-
white clip circuit
-
wideband circuit
-
wire circuit
-
wired AND circuit
-
wired circuit
-
wired OR circuit
-
wye-connected circuit
-
wye circuit
-
zero-lose circuit -
85 valve
1) = float needle2) клапан (рис. 15,16); вентиль; задвижка; заслонка; золотник; кран; распределительный кран; створка (дверцы); электронная лампа; гидро- или пневмораспределитель; затвор (гидротехнический); (редко) форсунка; II подавать через клапан; питать через клапан; снабжать; обеспечивать - time the valves - valve acceleration - valve-actuating gear - valve adjusting screw - valve arrangement - valve base patch - valve cock disk - valve control mechanism - valve diameter - valve dust cap - valve edge - valve enclosure - valve end - valve extractor - valve grinding - valve gutter - valve guttering - valve head slot - valve holder - valve hole - valve inside - valve inside plunger pin - valve knock - valve lag - valve lap - valve lead - valve lifter roller - valve lifter roller pin - valve lifting cam - valve location - valve manifold - valve mechanism - valve of tyre - valve operating mechanism - valve refacer - valve refacing - valve refacing machine - valve regulation - valve remover - valve reseating - valve retainer lock - valve return - valve rim - valve rocker arm - valve rocker lever - valve rocker pedestal - valve rocker roller - valve rocker roller pin - valve rocker shaft - valve scaling - valve scorching - valve seal - valve seat bore - valve seat extractor - valve seat grinder - valve seating - valve seating tool - valve sinkage - valve slot - valve spring compressor - valve spring damper - valve spring holder - valve spring key - valve spring lifter - valve spring remover - valve spring retainer - valve spring seat - valve spring seat key - valve spring seat pin - valve spring surge - valve spring tool - valve spring washer - valve stem end - valve stem groove - valve stem guide - valve stem seal - valve stripping - valve surge damper - valve system - valve tab - valve tappet clearance - valve tappet roller pin - valve tappet tube - valve tension spring - valve the gas - valve thimble - valve throat - valve timing - valve timing diagram - valve tip - valve train - valve travel - valve unit - valve unloader assembly - valve velocity - valve wrench - supplementary air valve - clapper swing-check valve - closed-centre valve - cross-feed valve - compensation valve - flapper-nozzle valve - flow regulator valve - large capacity brake valve - metering valve - multipurpose valve - pilot valve - programmable valve with 24 hour/7 day timer for closing and opening the compressed air ringmain - programmable valve with line-to-valve-connection and 1 BSP - quick-closing valve - quick-opening valve - single-stage valve - slide valve collar - sliding-sleeve valve - sliding throttle valve - spool valve - spring turn - spring-and-ball valve - stainless steel padlockable decompressing valve- T-valve- water check valve - water-cooled valve - zero-lap valve -
86 function Ak
функция Ak (реле времени)
Независимые задержки срабатывания и возврата реле, отсчитываемые от момента подачи и снятия напряжения с управляющего входа соответственно.
[Интент]EN
function Ak
Asymmetrical On-delay and Off-delay with external control
[Schneider Electric]Параллельные тексты EN-RU
Рис. Schneider Electric
U - Напряжение питания реле времени
С - Управляющий вход (положение контакта, коммутирующего управляющий вход)
G - Вход прерывания (положение контакта, коммутирующего вход прерывания)
R - контактный или полупроводниковый выход релеAfter power-up, closing of the control contact C causes the timing period T to start (timing can be interrupted by operating the Gate control contact G).
At the end of this timing period, the relay closes.
When control contact C re-opens, the timing T starts.
At the end of this timing period T, the output reverts to its initial position (timing can be interrupted by operating the Gate control contact G).
[Schneider Electric]После подачи питания на реле времени, а затем напряжения на управляющий вход С, начинается отсчет выдержки времени Т (отсчет может прерываться подачей напряжения на вход прерывания G).
По окончании выдержки времени контакт реле замыкается.
После снятия напряжения с управляющего входа С возобновляется отсчет выдержки времени Т.
По окончании выдержки времени контакт реле размыкается (реле времени возвращается в исходное положение). Отсчет выдержки времени может прерываться подачей напряжения на вход прерывания G.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Ak
-
87 time delay
- задержка срабатывания
- задержка (в электронно-лучевой трубке)
- задержка
- выдержка времени
- время задержки
- временная задержка
время задержки
—
[Интент]Параллельные тексты EN-RU
The relay remains energized for the duration of the timer.
[Schneider Electric]Реле остается включенным до истечения времени задержки.
[Перевод Интент]
Тематики
- электротехника, основные понятия
EN
выдержка времени
(в реле времени)
[Интент]Параллельные тексты EN-RU
The timing period T starts on energization.
At the end of the timing period T, the output R closes.
Closing of the control contact C makes the output R open.
Opening of control contact C restarts timing period T.
At the end of the timing period T, the output R closes.
[Schneider Electric]Отсчет выдержки времени T начинается от момента подачи питания на реле времени.
По окончании выдержки T выход R замыкается.
При подаче напряжения на управляющий вход C выход R размыкается.
В момент снятия напряжения с управляющего входа C вновь начинается отсчет выдержки T.
По окончании отсчета выдержки времени T выход R замыкается.
[Перевод Интент]
Тематики
Сопутствующие термины
- начало отсчета выдержки времени
- окончание выдержки времени
- отсчет выдержки времени
- прерывание отсчета выдержки времени
EN
временная задержка
запаздывание
фиксированная задержка
заданная задержка
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]
задержка
-
[Интент]
задержка
запаздывание
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]Тематики
Синонимы
EN
задержка
запаздывание
Период времени, который требуется для вывода изображения на экран электронно-лучевой трубки, в течение которого его не видно. Это вызвано эффектом послесвечения люминофора.
[ http://www.morepc.ru/dict/]Тематики
Синонимы
EN
задержка срабатывания
-
[Интент]Параллельные тексты EN-RU
As implemented in the LTM R controller, all motor protection function trip time delays are definite time, except for the Thermal Overload function, which also offers inverse thermal trip time delays.
[Schneider Electric]Применительно к контроллеру LTM R, все задержки срабатывания защиты электродвигателя являются фиксированными, кроме функции защиты от перегрузки, определяемой по тепловому состоянию, которая может использовать и обратнозависимые задержки срабатывания.
[Перевод Интент]When the overfluxing value exceeds this threshold the P63x will determine the tripping time according to the overfluxing magnitude value and the set characteristic.
[Schneider Electric]Если значение перевозбуждения становится выше заданного предельного значения, то устройство P63x определяет задержку срабатывания в зависимости от значения перевозбуждения и заданной характеристики.
[Перевод Интент]
Тематики
- автоматизация, основные понятия
- выключатель автоматический
- релейная защита
EN
Англо-русский словарь нормативно-технической терминологии > time delay
-
88 specified time
выдержка времени
(в реле времени)
[Интент]Параллельные тексты EN-RU
The timing period T starts on energization.
At the end of the timing period T, the output R closes.
Closing of the control contact C makes the output R open.
Opening of control contact C restarts timing period T.
At the end of the timing period T, the output R closes.
[Schneider Electric]Отсчет выдержки времени T начинается от момента подачи питания на реле времени.
По окончании выдержки T выход R замыкается.
При подаче напряжения на управляющий вход C выход R размыкается.
В момент снятия напряжения с управляющего входа C вновь начинается отсчет выдержки T.
По окончании отсчета выдержки времени T выход R замыкается.
[Перевод Интент]
Тематики
Сопутствующие термины
- начало отсчета выдержки времени
- окончание выдержки времени
- отсчет выдержки времени
- прерывание отсчета выдержки времени
EN
выдержка времени электрического реле
Интервал времени от момента подачи или съема возбуждения электрического реле до мгновения выполнения этим реле предназначенной функции, являющейся нормируемой характеристикой времени
[ ГОСТ 16022-83]EN
specified time
a time interval which is a specified characteristic of a specified-time relay
[IEV number 446-17-14]FR
temporisation
un des temps caractérisant une fonction d'un relais à temps spécifié
[IEV number 446-17-14]Тематики
EN
DE
FR
заданное время
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]
заданное время
-
[Интент]Тематики
- электротехника, основные понятия
EN
125. Выдержка времени электрического реле
D. Zeitverhalten
E. Specified time
F. Temporisation
Интервал времени от момента подачи или съема возбуждения электрического реле до мгновения выполнения этим реле предназначенной функции, являющейся нормируемой характеристикой времени
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Англо-русский словарь нормативно-технической терминологии > specified time
-
89 function D
функция D (реле времени)
Периодическая последовательность импульсов с равными длительностями паузы и импульса, начинающаяся с отсутствия импульса
[Интент]EN
function D
Symmetrical flasher relay (starting pulse off)
[Schneider Electric]
function D
Flip-flop
[Crouzet]Параллельные тексты EN-RU
Function D
Symmetrical flasher relay
Repetitive cycle with two timing periods T of equal duration, with output(s) R changing state at the end of each timing period T.
[Schneider Electric]Функция D
Периодическая последовательность импульсов с равными длительностями паузы и импульса
Периодическая последовательность с двумя выдержками времени T равной длительности, выход(ы) R меняе(ю)т свое состояние в конце каждой выдержки времени T.
[Перевод Интент]Function D
Flip-flop
Repetitive cycle which switches the output alternately between the rest and operating position for equal time bases.
[Crouzet]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function D
-
90 function Di
функция Di (реле времени)
Периодическая последовательность импульсов с равными длительностями паузы и импульса, начинающаяся с наличия импульса
[Интент]EN
function Di
Symmetrical flasher relay (starting pulse on)
[Schneider Electric]
function Di
Flip-flop
[Crouzet]Параллельные тексты EN-RU
Function Di
Symmetrical flasher relay
Repetitive cycle with two timing periods T of equal duration, with output(s) R changing state at the end of each timing period T.
[Schneider Electric]Функция Di
Периодическая последовательность импульсов с равными длительностями паузы и импульса
Периодическая последовательность с двумя выдержками времени T равной длительности, выход(ы) R меняе(ю)т свое состояние в конце каждой выдержки времени T.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Di
91 automatic
автоматический аппарат; II автоматический; самодействующий; автоматизированный- automatic acceleration control unit - automatic accumulator charging - automatic action - automatic adjustment - automatic adjustment mechanism - automatic advance control - automatic air regulator - automatic alarm - automatic alarm signal transmitter - automatic alternation - automatic amplitude control - automatic arc welding - automatic arc welding machine - automatic arc-welding machine - automatic assemblage - automatic assembly - automatic assembly machine - automatic backing-up - automatic backlash control - automatic backup - automatic balance control - automatic balancer - automatic balancing - automatic bar fed turning center - automatic bar feed - automatic bias control - automatic block - automatic bonding unit - automatic brake - automatic brake adjuster - automatic brake arrangement - automatic brake controller - automatic braking - automatic braking system - automatic brazing equipment - automatic buffing machine - automatic burette - automatic butt splicer - automatic calibration - automatic cam-controlled machine - automatic cathead - automatic centering - automatic chain-bending machine - automatic change of tools - automatic change-over - automatic change-over switch - automatic check - automatic check-out recording equipment - automatic checking balance - automatic checking machine - automatic checkout equipment - automatic checkout system - automatic checkout-and-readiness equipment - automatic choke - automatic chuck - automatic chuck extractor - automatic chuck-changing system - automatic chuck jaw changing - automatic chucker - automatic circuit - automatic circuit breaker - automatic circuit recloser - automatic climate control system - automatic closing system - automatic clutch - automatic cold upsetter - automatic come-along clamp - automatic compensation option - automatic compensator - automatic consistency checking - automatic constant tension mooring winch - automatic control - automatic control actuator - automatic control channel - automatic control circuit - automatic control engineering - automatic control equipment - automatic control halting instruction - automatic control installation - automatic control loop - automatic control rod - automatic control system - automatic controller - automatic conveying - automatic coupler - automatic coupling - automatic coupling device - automatic coupling screwing unit - automatic crab winch - automatic crimper - automatic crossover - automatic cut-out torque wrench - automatic cutout - automatic cycle - automatic cycle mechanism - automatic cycle working - automatic cycling equipment - automatic data analyzer - automatic data distribution - automatic data entry - automatic data processing - automatic data processing field branch - automatic data unit - automatic datum search - automatic deicing system - automatic device - automatic diagnosis - automatic diagnostic-and-recovery system - automatic discharging device - automatic disk changer - automatic door - automatic door closer - automatic door photoelectric relay - automatic drilling control - automatic drilling rig - automatic drinking bowl - automatic drive - automatic drive detection - automatic drive engagement - automatic dump - automatic-dump truck - automatic dust ejector - automatic dust unloading valve - automatic ejection - automatic electric drive - electrical drive - automatic electrode changer - automatic elevator - automatic emergency valve - automatic end stop - automatic error correction - automatic error detection - automatic exchange of tools - automatic expansion valve - automatic fault detection - automatic fault finding - automatic fault isolation - automatic fault isolation tester - automatic fault reporting - automatic fault signalling - automatic feature - automatic feed - automatic feed drill - automatic feed-off mechanism - automatic feeder - automatic feeding mechanism - automatic feedoff - automatic fire alarm - automatic fire alarm system - automatic fire annunciator - automatic fire detector - automatic fire sprinkler - automatic fixturing system - automatic flanger - automatic float-type pump-out unit - automatic flour meter - automatic flow tank - automatic focus correction servo-system - automatic forging machine - automatic front wheel drive engagement - automatic fuel economizing device - automatic fuel-control unit - automatic fuel saving device - automatic fuel shut-off - automatic fuse - automatic gage - automatic gaging-and-compensating system - automatic gain adjustment - automatic gain control - automatic gas-cutting machine - automatic gas-welding machine - automatic gate - automatic gate closer - automatic gate opener - automatic gauging - automatic gearbox - automatic generating plant - automatic generator - automatic grab - automatic gripper change - automatic gripper control - automatic guided vehicle - automatic half-hose machine - automatic heater - automatic hill holder - automatic hinged trip spider - automatic hitch - automatic holding - automatic holding device - automatic hopper-feed machine - automatic humidity regulator - automatic identification- Auto-ID- AIS - automatic idling control - automatic ignition - automatic ignition system - automatic ignition timing - automatic input - automatic insertion - automatic interlocking - automatic internal diagnosis - automatic jaw changer - automatic jaw shift device - automatic latching - automatic level - automatic level compensation - automatic level control - automatic level control system - automatic level gauge - automatic level setup - automatic leveling control system - automatic light - automatic light control - automatic light regulation - automatic line - automatic line disconnection - automatic line switching - ALS - automatic load control - automatic load sustaining brake - automatic load-gripping device - automatic loader - automatic loading - automatic lock - automatic locking - automatic locking holder - automatic locking hub - automatic locking spindle - automatic lockout - automatic lockout feature - automatic lubrication - automatic lubricator - automatic machine cycle - automatic magazine bar feed - automatic maintenance - automatic manipulator - automatic measurement-and-compensation system - automatic measuring facilities - automatic metal forming machine - automatic mixture control - automatic mode switching - automatic moisture regulator - automatic monitoring - automatic motor control gear - automatic movements starting - automatic multicam machine - automatic noise limiter - automatic noise-reduction system - automatic oil-flow controller - automatic oiling - automatic opening circuit breaker - automatic opening cover - automatic optimization - automatic overload control - automatic overload limiter - automatic overload stop - automatic packing - automatic pallet handler - automatic pallet storage-retrieval system - automatic part gaging - automatic part-loading conveyor - automatic photodetector - automatic pipe handling system - automatic pipe stabber - automatic placement - automatic plant - automatic polishing machine - automatic positioning - automatic power control - automatic power drawbar control - automatic power rotary scraper - automatic power slips - automatic press for cold pressing of nuts - automatic press for stamping electric motor stator and rotor notches - automatic pressure control - automatic pressure regulator - automatic probe changer - automatic probe changing - automatic probing cycle - automatic punch - automatic rack stacker - automatic radiator shutter - automatic ram pile driver - automatic reading - automatic reclosing circuit breaker - automatic recovery - automatic recovery program - automatic regulation - automatic regulation of belt tension - automatic regulation of drive chain tension - automatic regulation rod - automatic regulator - automatic release - automatic releaser - automatic repeat - automatic remote control - automatic reset - automatic reset-data circuit - automatic restart - automatic return - automatic return valve - automatic rotary line - automatic router - automatic routine - automatic rpm changer - automatic safety device - automatic sample changer - automatic sampler - automatic sampling - automatic sampling device - automatic sampling equipment - automatic sand-blasting machine - automatic scales - automatic screen - automatic selective overdrive - automatic sensitivity control - automatic set point - automatic shaft-position data encoder - automatic shaker bag - automatic shank spindle - automatic shift - automatic shut-off valve - automatic shutdown - automatic side-dumping - automatic signaling - automatic signalization - automatic size control tooling - automatic sorting machine - automatic spark advance - automatic spark advance governor - automatic spark advance magneto - automatic spark timer - automatic spectrometer - automatic spectrophotometer - automatic speed compensation - automatic speed control - automatic speed selection device - automatic spider - automatic spindle gear changing - automatic sprinkler fire control system - automatic stability - automatic stability controls - automatic stabilization and control system - automatic stabilizer - automatic stacker crane - automatic start - automatic starting - automatic starting motor - automatic start-up - automatic steel - automatic steering - automatic step selection - automatic stop - automatic stop switch - automatic straightening and cutting machine - automatic strip-straightening machine - automatic submerged-arc welder - automatic submerged-arc welding - automatic sucker rod spanner - automatic suction pump - automatic surveillance - automatic switch - automatic switchable redundance - automatic switchboard - automatic swivel spindle - automatic synchronization - automatic synchronizer - automatic takeup - automatic takeup mechanism - automatic temperature recording controller - automatic temperature regulator - automatic tensioning winch - automatic test analysis system - automatic test equipment - automatic test system - automatic thrust adjustment - automatic time switch - automatic time-delay switch - automatic timed magneto - automatic timer - automatic timing - automatic timing control - automatic timing device - automatic tipper - automatic tool changing apparatus - automatic tool transport mechanism - automatic tool wear-tool broken sensing system - automatic toolsetting - automatic tongs - automatic training idler - automatic transmission - automatic transmission fluid - automatic trip - automatic troubleshooting - automatic tuning - automatic two-speed geared head - automatic update - automatic vacuum deposition system - automatic valve - automatic valve adjustment - automatic viscosity controller - automatic voltage control - automatic voltage regulator - automatic warehousing - automatic warning - automatic washer - automatic water bowl - automatic water spray fire-fighting system - automatic weight controller - automatic weighing machine - automatic weigher - automatic weld - automatic welder - automatic welding - automatic welding machine - automatic wire feed - automatic workhandling - automatic workhandling device - automatic zero adjustment - automatic zero set92 function A
функция A (реле времени)
задержка срабатывания при подаче питания
[Интент]EN
function A
Параллельные тексты EN-RU
delay on energisation
[Crouzed]
function A
power on delay relay
[Schneider Electric]The timing period T begins on energization.
After timing, the output R close.
[Schneider Electric]Отсчет выдержки времени T начинается от момента подачи питания на реле времени.
По окончании выдержки T выход R замыкается.
[Перевод Интент]Single timing cycle which begins on energisation.
The output changes state after timing.
[Crouzed]Однократный отсчет выдержки времени, начинающийся от момента подачи питания на реле времени.
Выход реле изменяет свое состояние после окончания выдержки времени
[Перевод Интент]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function A
93 system
1) система || системный3) вчт операционная система; программа-супервизор5) вчт большая программа6) метод; способ; алгоритм•system halted — "система остановлена" ( экранное сообщение об остановке компьютера при наличии серьёзной ошибки)
- CPsystem- H-system- h-system- hydrogen-air/lead battery hybrid system- Ksystem- Lsystem- L*a*b* system- master/slave computer system- p-system- y-system- Δ-system94 function B
функция B (реле времени)
Формирование импульса при подаче напряжения на управляющий вход.
[Интент]EN
function B
Interval relay with control signal
[Schneider Electric]
function B
Timing on impulse one shot. On pulse (with constant supply)
[Crouzet]Параллельные тексты EN-RU
U - Напряжение питания реле времени
С - Управляющий вход (положение контакта, коммутирующего управляющий вход)
G - Вход прерывания (положение контакта, коммутирующего вход прерывания)
R - контактный или полупроводниковый выход релеAfter power-up, pulsing or maintaining control contact C starts the timing T.
The output R closes for the duration of the timing period T then reverts to its initial state.
[Schneider Electric]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function B
95 function C
функция C (реле времени)
Срабатывание при подаче напряжения на управляющий вход и задержка возврата при снятии напряжения с управляющего входа.
[Интент]EN
function C
Off-delay relay with control signal
[Schneider Electric]
function C
Timing after impulse
Delay OFF (with constant supply
[Crouzet]Параллельные тексты EN-RU
U - Напряжение питания реле времени
С - Управляющий вход (положение контакта, коммутирующего управляющий вход)
G - Вход прерывания (положение контакта, коммутирующего вход прерывания)
R - контактный или полупроводниковый выход релеAfter power-up and closing of the control contact C, the output R closes.
When control contact C re-opens, timing T starts.
At the end of the timing period, output(s) R revert(s) to its/their initial state.
[Schneider Electric]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function C
96 реле времени
97 system
система; установка; устройство; ркт. комплекс"see to land" system — система посадки с визуальным приземлением
A.S.I. system — система указателя воздушной скорости
ablating heat-protection system — аблирующая [абляционная] система тепловой защиты
ablating heat-shield system — аблирующая [абляционная] система тепловой защиты
active attitude control system — ксм. активная система ориентации
aft-end rocket ignition system — система воспламенения заряда с задней части РДТТ [со стороны сопла]
aircraft response sensing system — система измерений параметров, характеризующих поведение ЛА
air-inlet bypass door system — дв. система перепуска воздуха на входе
antiaircraft guided missile system — ракетная система ПВО; зенитный ракетный комплекс
antiaircraft guided weapons system — ракетная система ПВО; зенитный ракетный комплекс
attenuated intercept satellite rendez-vous system — система безударного соединения спутников на орбите
attitude and azimuth reference system — система измерения или индикации углов тангажа, крена и азимута
automatic departure prevention system — система автоматического предотвращения сваливания или вращения после сваливания
automatic drift kick-off system — система автоматического устранения угла упреждения сноса (перед приземлением)
automatic hovering control system — верт. система автостабилизации на висении
automatic indicating feathering system — автоматическая система флюгирования с индикацией отказа (двигателя)
automatic mixture-ratio control system — система автоматического регулирования состава (топливной) смеси
automatic pitch control system — автомат тангажа; автоматическая система продольного управления [управления по каналу тангажа]
B.L.C. high-lift system — система управления пограничным слоем для повышения подъёмной силы (крыла)
backpack life support system — ксм. ранцевая система жизнеобеспечения
beam-rider (control, guidance) system — ркт. система наведения по лучу
biowaste electric propulsion system — электрический двигатель, работающий на биологических отходах
buddy (refueling, tank) system — (подвесная) автономная система дозаправки топливом в полете
closed(-circuit, -cycle) system — замкнутая система, система с замкнутым контуром или циклом; система с обратной связью
Cooper-Harper pilot rating system — система баллов оценки ЛА лётчиком по Куперу — Харперу
deployable aerodynamic deceleration system — развёртываемая (в атмосфере) аэродинамическая тормозная система
depressurize the fuel system — стравливать избыточное давление (воздуха, газа) в топливной системе
driver gas heating system — аэрд. система подогрева толкающего газа
dry sump (lubrication) system — дв. система смазки с сухим картером [отстойником]
electrically powered hydraulic system — электронасосная гидросистема (в отличие от гидросистемы с насосами, приводимыми от двигателя)
exponential control flare system — система выравнивания с экспоненциальным управлением (перед приземлением)
flywheel attitude control system — ксм. инерционная система ориентации
gas-ejection attitude control system — ксм. газоструйная система ориентация
gas-jet attitude control system — ксм. газоструйная система ориентация
ground proximity extraction system — система извлечения грузов из самолёта, пролетающего на уровне земли
hot-air balloon water recovery system — система спасения путем посадки на воду с помощью баллонов, наполняемых горячими газами
hypersonic air data entry system — система для оценки аэродинамики тела, входящего в атмосферу планеты с гиперзвуковой скоростью
igh-temperature fatigue test system — установка для испытаний на выносливость при высоких температурах
interceptor (directing, vectoring) system — система наведения перехватчиков
ion electrical propulsion system — ксм. ионная двигательная установка
isotope-heated catalytic oxidizer system — система каталитического окислителя с нагревом от изотопного источника
jet vane actuation system — ркт. система привода газового руля
laminar flow pumping system — система насосов [компрессоров] для ламинаризации обтекания
launching range safety system — система безопасности ракетного полигона; система обеспечения безопасности космодрома
leading edge slat system — система выдвижных [отклоняемых] предкрылков
low-altitude parachute extraction system — система беспосадочного десантирования грузов с малых высот с использованием вытяжных парашютов
magnetic attitude control system — ксм. магнитная система ориентации
magnetically slaved compass system — курсовая система с магнитной коррекцией, гироиндукционная курсовая система
mass-expulsion attitude control system — система ориентации за счёт истечения массы (газа, жидкости)
mass-motion attitude control system — ксм. система ориентации за счёт перемещения масс
mass-shifting attitude control system — ксм. система ориентации за счёт перемещения масс
monopropellant rocket propulsion system — двигательная установка с ЖРД на унитарном [однокомпонентном] топливе
nucleonic propellant gauging and utilization system — система измерения и регулирования подачи топлива с использованием радиоактивных изотопов
open(-circuit, -cycle) system — открытая [незамкнутая] система, система с незамкнутым контуром или циклом; система без обратной связи
plenum chamber burning system — дв. система сжигания топлива во втором контуре
positioning system for the landing gear — система регулирования высоты шасси (при стоянке самолёта на земле)
radar altimeter low-altitude control system — система управления на малых высотах с использованием радиовысотомера
radar system for unmanned cooperative rendezvous in space — радиолокационная система для обеспечения встречи (на орбите) беспилотных кооперируемых КЛА
range and orbit determination system — система определения дальностей [расстояний] и орбит
real-time telemetry processing system — система обработки радиотелеметрических данных в реальном масштабе времени
recuperative cycle regenerable carbon dioxide removal system — система удаления углекислого газа с регенерацией поглотителя, работающая по рекуперативному циклу
rendezvous beacon and command system — маячно-командная система обеспечения встречи («а орбите)
satellite automatic terminal rendezvous and coupling system — автоматическая система сближения и стыковки спутников на орбите
Schuler tuned inertial navigation system — система инерциальной навигации на принципе маятника Шулера
sodium superoxide carbon dioxide removal system — система удаления углекислого газа с помощью надперекиси натрия
space shuttle separation system — система разделения ступеней челночного воздушно-космического аппарата
stellar-monitored astroinertial navigation guidance system — астроинерциальная система навигации и управления с астрокоррекцией
terminal control landing system — система управления посадкой по траектории, связанной с выбранной точкой приземления
terminal descent control system — ксм. система управления на конечном этапе спуска [снижения]
terminal guidance system for a satellite rendezvous — система управления на конечном участке траектории встречи спутников
test cell flow system — ркт. система питания (двигателя) топливом в огневом боксе
vectored thrust (propulsion) system — силовая установка с подъёмно-маршевым двигателем [двигателями]
water to oxygen system — ксм. система добывания кислорода из воды
wind tunnel data acquisition system — система регистрации (и обработки) данных при испытаниях в аэродинамической трубе
— D system98 реле времени
Большой англо-русский и русско-английский словарь > реле времени
99 control
1) управление; регулирование || управлять; регулировать2) контроль || контролировать3) управляющее устройство; устройство управления; регулятор4) профессиональное мастерство, квалификация, техническая квалификация5) pl органы управления•"in control" — "в поле допуска" ( о результатах измерения)
to control closed loop — управлять в замкнутой системе; регулировать в замкнутой системе
- 2-handed controlsto control open loop — управлять в разомкнутой системе; регулировать в разомкнутой системе
- 32-bit CPU control
- acceptance control
- access control
- acknowledge control
- active process control
- adaptable control
- adaptive constraint control
- adaptive control for optimization
- adaptive control
- adaptive feed rate control
- adaptive quality control
- adjustable feed control
- adjustable rotary control
- adjustable speed control
- adjusting control
- adjustment control
- AI control
- air logic control
- analog data distribution and control
- analogical control
- analytical control
- application control
- arrows-on-curves control
- autodepth control
- autofeed control
- automated control of a document management system
- automated technical control
- automatic backlash control
- automatic control
- automatic editing control
- automatic gain control
- automatic gripper control
- automatic level control
- automatic process closed loop control
- automatic remote control
- automatic sensitivity control
- automatic sequence control
- automatic speed control
- automatic stability controls
- auxiliaries control
- balanced controls
- band width control
- bang-bang control
- bang-bang-off control
- basic CNC control
- batch control
- bibliographic control
- bin level control
- boost control
- built-in control
- button control
- cam control
- cam throttle control
- camshaft control
- carriage control
- Cartesian path control
- Cartesian space control
- cascade control
- C-axis spindle control
- cell control
- center control
- central control
- central supervisory control
- centralized control
- centralized electronic control
- central-station control
- changeover control
- chip control
- circumferential register control
- close control
- closed cycle control
- closed loop control
- closed loop machine control
- closed loop manual control
- closed loop numerical control
- closed loop position control
- clutch control
- CNC control
- CNC indexer control
- CNC programmable control
- CNC symbolic conversational control
- CNC/CRT control
- CNC/MDI control
- coarse control
- coded current control
- coded current remote control
- color control
- combination control
- command-line control
- compensatory control
- composition control
- compound control
- computed-current control
- computed-torque control
- computer control
- computer numerical control
- computer process control
- computer-aided measurement and control
- computer-integrated manufacturing control
- computerized control
- computerized numerical control
- computerized process control
- constant surface speed control
- constant value control
- contactless control
- contact-sensing control
- contamination control
- continuous control
- continuous path control
- continuous process control
- contour profile control
- contouring control
- conventional hardware control
- conventional numerical control
- conventional tape control
- convergent control
- conversational control
- conversational MDI control
- coordinate positioning control
- coordinate programmable control
- copymill control
- counter control
- crossed controls
- current control
- cycle control
- dash control
- data link control
- data storage control
- deadman's handle controls
- depth control
- derivative control
- dial-in control
- differential control
- differential gaging control
- differential gain control
- differential temperature control
- digital brushless servo control
- digital control
- digital position control
- digital readout controls
- dimensional control
- direct computer control
- direct control
- direct digital control
- direct numerical control
- direction control
- directional control
- dirt control
- discontinuous control
- discrete control
- discrete event control
- discrete logic controls
- dispatching control
- displacement control
- distance control
- distant control
- distributed control
- distributed numerical control
- distributed zone control
- distribution control
- dog control
- drum control
- dual control
- dual-mode control
- duplex control
- dust control
- dynamic control
- eccentric control
- edge position control
- EDP control
- electrical control
- electrofluidic control
- electromagnetic control
- electronic control
- electronic level control
- electronic speed control
- electronic swivel control
- elevating control
- emergency control
- end-point control
- engineering change control
- engineering control
- entity control
- environmental control
- error control
- error plus error-rate control
- error-free control
- external beam control
- factory-floor control
- false control
- feed control
- feed drive controls
- feedback control
- feed-forward control
- field control
- fine control
- finger-tip control
- firm-wired numerical control
- fixed control
- fixed-feature control
- fixture-and-tool control
- flexible-body control
- floating control
- flow control
- fluid flow control
- follow-up control
- foot pedal control
- force adaptive control
- forecasting compensatory control
- fork control
- four quadrant control
- freely programmable CNC control
- frequency control
- FROG control
- full computer control
- full order control
- full spindle control
- gage measurement control
- gain control
- ganged control
- gap control
- gear control
- generative numerical control
- generic path control
- geometric adaptive control
- graphic numerical control
- group control
- grouped control
- guidance control
- hairbreath control
- hand control
- hand feed control
- hand wheel control
- hand-held controls
- handle-type control
- hand-operated controls
- hardened computer control
- hardwared control
- hardwared numerical control
- heating control
- heterarchical control
- hierarchical control
- high-integrity control
- high-level robot control
- high-low control
- high-low level control
- high-technology control
- horizontal directional control
- humidity control
- hybrid control
- hydraulic control
- I/O control
- immediate postprocess control
- inching control
- in-cycle control
- independent control
- indexer control
- indirect control
- individual control
- industrial processing control
- industrial-style controls
- infinite control
- infinite speed control
- in-process control
- in-process size control
- in-process size diameters control
- input/output control
- integral CNC control
- integral control
- integrated control
- intelligent control
- interacting control
- interconnected controls
- interlinking control
- inventory control
- job control
- jogging control
- joint control
- joystick control
- just-in-time control
- language-based control
- laser health hazards control
- latching control
- lead control
- learning control
- lever control
- lever-operated control
- line motion control
- linear control
- linear path control
- linearity control
- load control
- load-frequency control
- local control
- local-area control
- logic control
- lubricating oil level control
- machine control
- machine programming control
- machine shop control
- macro control
- magnetic control
- magnetic tape control
- main computer control
- malfunction control
- management control
- manual control
- manual data input control
- manual stop control
- manually actuatable controls
- manufacturing change control
- manufacturing control
- master control
- material flow control
- MDI control
- measured response control
- mechanical control
- memory NC control
- memory-type control
- metering control
- metrological control of production field
- microbased control
- microcomputer CNC control
- microcomputer numerical control
- microcomputer-based sequence control
- microprocessor control
- microprocessor numerical control
- microprogrammed control
- microprogramming control
- milling control
- model reference adaptive control
- model-based control
- moisture control
- motion control
- motor control
- motor speed control
- mouse-driven control
- movable control
- multicircuit control
- multidiameter control
- multilevel control
- multimachine tool control
- multiple control
- multiple-processor control
- multiposition control
- multistep control
- multivariable control
- narrow-band proportional control
- navigation control
- NC control
- neural network adaptive control
- noise control
- noncorresponding control
- noninteracting control
- noninterfacing control
- nonreversable control
- nonsimultaneous control
- numerical contouring control
- numerical control
- numerical program control
- odd control
- off-line control
- oligarchical control
- on-board control
- one-axis point-to-point control
- one-dimensional point-to-point control
- on-line control
- on-off control
- open loop control
- open loop manual control
- open loop numerical control
- open-architecture control
- operating control
- operational control
- operator control
- optical pattern tracing control
- optimal control
- optimalizing control
- optimizing control
- oral numerical control
- organoleptic control
- overall control
- overheat control
- override control
- p. b. control
- palm control
- parameter adaptive control
- parameter adjustment control
- partial d.o.f. control
- path control
- pattern control
- pattern tracing control
- PC control
- PC-based control
- peg board control
- pendant control
- pendant-actuated control
- pendant-mounted control
- performance control
- photoelectric control
- physical alignment control
- PIC control
- PID control
- plugboard control
- plug-in control
- pneumatic control
- point-to-point control
- pose-to-pose control
- position/contouring numerical control
- position/force control
- positional control
- positioning control
- positive control
- postprocess quality control
- power adaptive control
- power control
- power feed control
- power-assisted control
- powered control
- power-operated control
- precision control
- predictor control
- preselective control
- preset control
- presetting control
- pressbutton control
- pressure control
- preview control
- process control
- process quality control
- production activity control
- production control
- production result control
- programmable adaptive control
- programmable cam control
- programmable control
- programmable logic adaptive control
- programmable logic control
- programmable machine control
- programmable microprocessor control
- programmable numerical control
- programmable sequence control
- proportional plus derivative control
- proportional plus floating control
- proportional plus integral control
- prototype control
- pulse control
- pulse duration control
- punched-tape control
- purpose-built control
- pushbutton control
- quality control
- radio remote control
- radium control
- rail-elevating control
- ram stroke control
- ram-positioning control
- rapid-traverse controls for the heads
- rate control
- ratio control
- reactive control
- real-time control
- reduced-order control
- register control
- registration control
- relay control
- relay-contactor control
- remote control
- remote program control
- remote switching control
- remote valve control
- remote-dispatch control
- resistance control
- resolved motion rate control
- retarded control
- reversal control
- revolution control
- rigid-body control
- robot control
- robot perimeter control
- robot teach control
- rod control
- safety control
- sampled-data control
- sampling control
- schedule control
- SCR's control
- second derivative control
- selective control
- selectivity control
- self-acting control
- self-adaptive control
- self-adjusting control
- self-aligning control
- self-operated control
- self-optimizing control
- self-programming microprocessor control
- semi-automatic control
- sensitivity control
- sensor-based control
- sequence control
- sequence-type control
- sequential control
- series-parallel control
- servo control
- servo speed control
- servomotor control
- servo-operated control
- set value control
- shaft speed control
- shape control
- shift control
- shop control
- shower and high-pressure oil temperature control
- shut off control
- sight control
- sign control
- single variable control
- single-flank control
- single-lever control
- size control
- slide control
- smooth control
- software-based NC control
- softwared numerical control
- solid-state logic control
- space-follow-up control
- speed control
- stabilizing control
- stable control
- standalone control
- start controls
- static control
- station control
- statistical quality control
- steering control
- step-by-step control
- stepless control
- stepped control
- stick control
- stock control
- stop controls
- stop-point control
- storage assignment control
- straight cut control
- straight line control
- stroke control
- stroke length control
- supervisor production control
- supervisory control
- swarf control
- switch control
- symbolic control
- synchronous data link control
- table control
- tap-depth controls
- tape control
- tape loop control
- teach controls
- temperature control
- temperature-humidity air control
- template control
- tension control
- test control
- thermal control
- thermostatic control
- three-axis contouring control
- three-axis point-to-point control
- three-axis tape control
- three-mode control
- three-position control
- throttle control
- thumbwheel control
- time control
- time cycle control
- time optimal control
- time variable control
- time-critical control
- time-proportional control
- timing control
- token-passing access control
- tool life control
- tool run-time control
- torque control
- total quality control
- touch-panel NC control
- touch-screen control
- tracer control
- tracer numerical control
- trajectory control
- triac control
- trip-dog control
- TRS/rate control
- tuning control
- turnstile control
- two-axis contouring control
- two-axis point-to-point control
- two-dimension control
- two-hand controls
- two-position control
- two-position differential gap control
- two-step control
- undamped control
- user-adjustable override controls
- user-programmable NC control
- variable flow control
- variable speed control
- variety control
- varying voltage control
- velocity-based look-ahead control
- vise control
- vision responsive control
- visual control
- vocabulary control
- vocal CNC control
- vocal numerical control
- voltage control
- warehouse control
- washdown control
- water-supply control
- welding control
- wheel control
- wide-band control
- zero set control
- zoned track controlEnglish-Russian dictionary of mechanical engineering and automation > control
100 circuit
1) схема; цепь; контур2) линия3) канал4) сеть•- adapter circuit
- adjustment circuit
- alive circuit
- announcing circuit
- anode circuit
- antisidetone circuit
- asynchronous circuit
- automatic reset-data circuit
- automatic ringdown circuit
- automatic start circuit
- auxiliary circuit
- balanced circuit
- balanced-wire circuit
- balancing circuit
- band-switching circuit
- basic circuit
- black-level restoring circuit
- black-level stretch circuit
- bootstrap circuit
- branch circuit
- branched circuit
- bridge antisidetone circuit
- building-out circuit
- built-up circuit
- Buttler circuit
- bypass circuit
- cached circuit
- call circuit
- capacitor-coupled circuit
- capacitor-switched circuit
- capacitor-switching circuit
- central-battery circuit
- chain-type connection circuit
- character generator large-scale integration circuit
- charge-coupled device circuit
- check parity circuit
- checkout circuit
- chrominance matrix circuit
- chrominance separation circuit
- chrominance takeoff circuit
- clamp-on circuit
- closed circuit
- coarse phasing circuit
- coaxial circuit
- coincidence circuit
- color-balance circuit
- color-indexing circuit
- color-purity circuit
- combinational-circuit circuit
- combined-supply circuit
- common-base circuit
- common-battery circuit
- common-collector circuit
- common-drain circuit
- common-emitter circuit
- common-gate circuit
- common-source circuit
- common-user circuit
- communication circuit
- comparing circuit
- compensating antisidetone circuit
- complemental metal-oxide-semiconductor circuit
- composite circuit
- conductor-bundled static wire circuit
- conference circuit
- connecting circuit
- constant-closed circuit
- contactor-relay circuit
- continental circuit
- convergence circuit
- cord circuit
- correcting circuit
- Costas circuit
- counter-coupling circuit
- counting-down circuit
- coupled circuit
- cross-bus matrix circuit
- crossed-waveguide circuit
- cue circuit
- cutoff circuit
- Darlingtone circuit
- data circuit
- data-transmission circuit
- dc restoration circuit
- decoder circuit
- delay circuit
- demodulation circuit
- dial-up circuit
- diamond circuit
- differencing circuit
- differential-frequency circuit
- digital circuit
- digital-excitation circuit
- digital-leased circuit
- diode-clamping circuit
- diode-clipping circuit
- diode-stabilitron circuit
- direct international circuit
- direct-connection circuit
- direct-transit international circuit
- direct-wire circuit
- double half-wave circuit
- double-ended cord circuit
- double-loop circuit
- dual circuit
- earth circuit
- earthed circuit
- echo-absorption circuit
- edge derivation circuit
- electric circuit
- electronic circuit
- elementary circuit
- encoding circuit
- energized circuit
- engineering circuit
- equivalent circuit
- error-subtracting circuit
- external circuit
- fallback circuit
- feed circuit
- feedback circuit
- fiber-optic circuit
- fire-control circuit
- fixed-virtual circuit
- flexible circuit
- flexible-stage circuit
- flywheel circuit
- forked circuit
- four-wire circuit
- frame scanning circuit
- frequency-changing circuit
- frequency-protection circuit
- full-accessible circuit
- full-period allocated circuit
- functional-switching circuit
- gallium-arsenide integrated circuit
- gating circuit
- generating circuit
- Gilbert circuit
- Grets circuit
- grid circuit
- ground-return circuit
- grouping circuit
- half-bridge circuit
- half-wave circuit
- hardened circuit
- head circuit
- HF-correction circuit
- holding circuit
- horizontal deflection circuit
- hybrid circuit
- hypothetical reference circuit
- idle lighting limiting circuit
- inclined adjustment circuit
- incoming circuit
- independent circuit
- inductive circuit
- input circuit
- input-by-output matrix circuit
- inquiry circuit
- integrated circuit
- integrating circuit
- interchange circuit
- interface-integrated circuit
- interferenced circuit
- interferencing circuit
- international leased circuit
- interstage coupling circuit
- invertor circuit
- ISDN echo cancellation circuit
- isochronic circuit
- Jiakoletto circuit
- junction circuit
- Karp circuit
- keep-alive circuit
- key section power circuit
- killer circuit
- ladder circuit
- lamp circuit
- large-scale integration circuit
- latched circuit
- LCR circuit
- lead changeover circuit
- LF-correction circuit
- line circuit
- linear circuit
- link circuit
- live circuit
- local circuit
- lock-in circuit
- locking circuit
- lock-out circuit
- long circuit
- long-distance circuit
- longitudinal circuit
- loop circuit
- lossless resonant circuit
- L-shaped circuit
- magnetic convergence circuit
- main supply circuit
- make circuit
- Marx circuit
- match circuit
- matching circuit
- matrix circuit
- message circuit
- microelectronic circuit
- microphone supply circuit
- multidrop circuit
- multijunctor circuit
- multiloop circuit
- multipoint circuit
- muting circuit
- neodymium magnetic circuit
- neutral circuit
- neutralization circuit
- neutralizing circuit
- noise-rejecting circuit
- noise-suicide circuit
- nonlinear circuit
- NOT circuit
- on-call circuit
- open circuit
- optoelectronic integrated circuit
- OR circuit
- order wire circuits
- OR-ELSE circuit
- oscillating circuit
- oscillation circuit
- output circuit
- output voltage tracking circuit
- packaged circuit
- paging circuit
- parallel circuit
- partially accessible circuit
- peaking circuit
- periodic closed circuit
- phantom circuit
- phase comparating circuit
- phase compensating circuit
- phase-shift circuit
- phase-substitution circuit
- physical circuit
- pilot circuit
- pilot-make-busy circuit
- planar circuit
- point-to-point circuit
- polling circuit
- polyphase circuit
- power circuit
- power-supply circuit
- precision phasing circuit
- primary circuit
- printed circuit
- private leased circuit
- protection circuit
- pulse-phase control circuit
- push-to-talk circuit
- push-to-type circuit
- quenching circuit
- quiet-tuning circuit
- radial supply circuit
- radio circuit
- RC circuit
- reactance control circuit
- reading circuit
- rectification circuit
- reference circuit
- rejecting circuit
- relay cutout circuit
- remote control circuit
- remote-ring circuit
- repeat circuit
- reset circuit
- resonance circuit
- resonant circuit
- reverse circuit
- reverse diode circuit
- ring circuit
- ringing circuit
- sample-and-hold circuit
- scaling circuit
- Scott circuit
- secondary circuit
- section substitution circuit
- selecting circuit
- selective circuit
- self-locked circuit
- series circuit
- series-oscillating circuit
- series-parallel circuit
- series-peaking circuit
- series-tuned circuit
- shaping circuit
- shaved single frequency circuit
- short circuit
- shunt circuit
- shunting circuit
- shunt-peaking circuit
- side circuit
- signal circuit
- signal processing circuit
- signal recovery circuit
- single-current circuit
- single-ended push-pull circuit
- single-frequency resonance circuit
- single-phase bridge circuit
- single-phase circuit
- snap-acting circuit
- solving circuit
- sound-program circuit
- spark-safe circuit
- speech circuit
- speed regulating circuit
- squaring circuit
- stabilizer circuit
- stable circuit
- stage circuit
- stage control circuit
- standard cable circuit
- standard circuit
- standby circuit
- stenode circuit
- storage large-scale integration circuit
- storage locking circuit
- straightforward circuit
- strap magnetic circuit
- strip-line circuit
- super large scale integration circuit
- superimposed circuit
- superposed circuit
- supply circuit
- sweep circuit
- switched circuit
- switching circuit
- symistor control circuit
- synchronous circuit
- tail circuit
- talk-back circuit
- tandem data circuit
- tank circuit
- tapped magnetic circuit
- tapped stage circuit
- telecommunication circuit
- telecommunication-protection circuit
- telegraph circuit
- telegraph grade circuit
- telegraph signal generating circuit
- telephone circuit
- telephone signal generating circuit
- telesignaling receiving circuit
- telesignaling sending circuit
- television circuit
- terminal circuit
- test circuit
- testing circuit
- third circuit
- three-loop circuit
- three-phase input circuit
- three-wire circuit
- through circuit
- thyristor control circuit
- time protection circuit
- time-delay circuit
- time-interval protection circuit
- time-setting circuit
- timing circuit
- toll circuit
- touch sensing circuit
- touch tone dial circuit
- transformer substitution circuit
- transformer-coupled circuit
- transistor clipping circuit
- transistor collector circuit
- transistor control circuit
- transistor protection circuit
- tributary circuit
- triode clamp circuit
- trunk circuit
- T-shaped circuit
- tuned circuit
- twelve-pulse circuit
- two-frequency resonance circuit
- two-loop circuit
- two-wire-ground circuit
- uniform circuit
- unstable circuit
- untapped circuit
- untapped magnetic circuit
- U-shaped circuit
- variometer controlling circuit
- video circuit
- virtual circuit
- voice circuit
- voltage multiplying circuit
- voltage sensor circuit
- watching output circuit
- wideband circuit
- wire circuit
- wired circuitEnglish-Russian dictionary of telecommunications and their abbreviations > circuit
СтраницыСм. также в других словарях:
Electronic timing relay — Электронное реле времени … Краткий толковый словарь по полиграфии
Digital protective relay — In electrical engineering of power systems, a digital protective relay uses a microcontroller with software based protection algorithms for the detection of electrical faults. Such relays are also termed as microprocessor type protective relays.… … Wikipedia
Swimming at the 2008 Summer Olympics - Men's 4 x 100 metre freestyle relay — Infobox Olympic event event = Men s 4×100 metre freestyle relay games = 2008 Summer caption = The medal ceremony of the event. venue = Beijing National Aquatics Center dates = August 10 (qualification) August 11 (final) competitors = TBD nations … Wikipedia
Large Observatory For X-ray Timing — Caractéristiques Organisation Agence spatiale européenne Domaine Observation du Soleil Type de mission télescope X Statut projet Masse 2 tonnes … Wikipédia en Français
Swimming at the 2008 Summer Olympics - Women's 4 x 100 metre medley relay — The women s 4×100 metre medley relay event at the 2008 Olympic Games took place on 15th (qualification) and 17th August (final) at the Beijing National Aquatics Centre. This swimming event used medley swimming as a relay. Because an Olympic size… … Wikipedia
Men's 4 x 100 metres relay world record progression — The first world record in the 4 x 100 metres relay for men (athletics) was recognized by the International Amateur Athletics Federation, now known as the International Association of Athletics Federations, in 1912. To June 21, 2009, the IAAF has… … Wikipedia
Swimming at the 2008 Summer Olympics - Men's 4 x 100 metre medley relay — The men s 4×100 metre medley relay event at the 2008 Olympic Games took place on August 15 (qualification) and August 17 (final) at the Beijing National Aquatics Center. This swimming event uses medley swimming as a relay. Because an Olympic size … Wikipedia
Swimming at the 2008 Summer Olympics - Women's 4 x 100 metre freestyle relay — The women s 4×100 metre freestyle relay event at the 2008 Olympic Games took place on 9th (qualification) and 10th August (final) at the Beijing National Aquatics Centre. This swimming event used freestyle as a relay, with swimmers typically… … Wikipedia
Swimming at the 2008 Summer Olympics - Women's 4 x 200 metre freestyle relay — The women s 4×200 metre freestyle relay event at the 2008 Olympic Games took place on 13th (Qualification) and 14th August (final) at the Beijing National Aquatics Centre. This swimming event used freestyle as a relay, with swimmers typically… … Wikipedia
электрическое реле времени — Логическое электрическое реле с нормируемой выдержкой времени [ГОСТ 16022 83] EN time relay specified time relay (deprecated) all or nothing relay with one or more specified time functions [IEV number 445 01 01] FR relais à temps… … Справочник технического переводчика
component — Synonyms and related words: actuator, adjunct, air, amplifier, anode, appurtenance, aspect, atom, atomic particles, base, brute matter, building block, capacitator, cathode, chemical element, circumstance, clock, constituent, contents, contingent … Moby Thesaurus
Перевод: со всех языков на русский
с русского на все языки- С русского на:
- Все языки
- Со всех языков на:
- Все языки
- Английский
- Болгарский
- Испанский
- Немецкий
- Румынский, Молдавский
- Русский
- Сербский
- Финский
- Французский