-
1 thermal load
Dictionary of Engineering, architecture and construction > thermal load
-
2 перегрузка
- surcharge d’un circuit
- surcharge
- débordement
перегрузка
Условия появления сверхтока в электрически не поврежденной цепи.
МЭК 60050(441-11-08).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
перегрузка
Условия оперирования в электрически неповреждённой цепи, которые вызывают сверхток.
В электрических цепях электроустановки здания могут возникать сверхтоки при отсутствии в них электрических повреждений. Причиной появления этих сверхтоков является перегрузка электрических цепей. Перегрузка характеризуется током перегрузки, который превышает номинальный ток электрической цепи и допустимые длительные токи её проводников. Длительная перегрузка проводников может вызвать их сильный нагрев и стать причиной пожара в здании. Поэтому в электроустановках зданий выполняют защиту от перегрузок с помощью устройств защиты от сверхтока. Перегрузки могут также возникать при переходных процессах в электрических цепях, например, при включении электрооборудования.
[ http://www.volt-m.ru/glossary/letter/%CF/view/46/]
перегрузка
Отношение время/электрический ток для цепи, в которой превышена максимальная допустимая нагрузка, когда цепь находится в исправном состоянии.
Примечание - Не следует использовать термин «перегрузка» как синоним термина «сверхток».
[ГОСТ ЕН 1070-2003]
перегрузка (цепи)
Времятоковая зависимость для цепи, в которой превышена максимальная нагрузка, когда цепь находится в исправном состоянии.
Примечание
Не следует использовать термин «перегрузка» как синоним сверхтока.
[ ГОСТ Р МЭК 60204-1-2007]
перегрузка
Превышение фактического значения мощности или тока электротехнического изделия (устройства) над номинальным значением.
Примечание. Допускается с введением соответствующего пояснения оценивать перегрузку полным значением параметра, превышающим номинальное значение.
[ ГОСТ 18311-80]
перегрузка
-
[IEV number 314-02-09]EN
overload
operating conditions in an electrically undamaged circuit which cause an over-current.
[IEC 60947-1, ed. 5.0 (2007-06)]
overload, noun
excess of the actual load over the full load, expressed by their difference
Source: 151-15-16
[IEV number 151-15-30]
overflow
condition which occurs when the numerical value of the output information exceeds the maximum possible value which can be displayed or represented
[IEV number 314-02-09]FR
surcharge
conditions de fonctionnement d’un circuit électriquement sain, qui provoquent une surintensité.
[IEC 60947-1, ed. 5.0 (2007-06)]
surcharge, f
excédent de la charge réelle sur la pleine charge, exprimé par leur différence
Source: 151-15-16
[IEV number 151-15-30]
débordement
condition de fonctionnement pour lequel la valeur numérique de l'information de sortie dépasse la possibilité maximale d'affichage ou de représentation de l'appareil
[IEV number 314-02-09]Тематики
- электротехника, основные понятия
Синонимы
EN
- OL
- overcharge
- overdrive
- overflow
- overload
- overload of a circuit
- overloading
- ovId
- surcharge load
- thermal overload situation
DE
FR
- débordement
- surcharge
- surcharge d’un circuit
Русско-французский словарь нормативно-технической терминологии > перегрузка
-
3 пуск переключением со звезды на треугольник
пуск переключением со звезды на треугольник
-EN
star-delta starting
the process of starting a three-phase motor by connecting it to the supply with the primary winding initially connected in star, then reconnected in delta for the running condition
[IEV number 411-52-16]FR
démarrage étoile-triangle
mode de démarrage d'un moteur triphasé à tension réduite, consistant à relier à la source à tension constante les enroulements statoriques, d'abord en couplage étoile, puis à passer au couplage triangle pour le fonctionnement normal
[IEV number 411-52-16]Magnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Y/Δ changeover node - Узел переключения со звезды на треугольник
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Contactor KΔ - Контактор KΔ
Contactor KY- Контактор KY
Параллельные тексты EN-RU Star-delta Y/Δ starting
Star-delta starting is the best known system and perhaps the commonest starting system at reduced voltage; it is used to start the motor reducing the mechanical stresses and limiting the current values during starting; on the other hand, it makes available a reduced inrush torque.This system can be used for motors with terminal box with 6 terminals and double supply voltage.
It is particularly suitable for no-load starting or with low and constant load torque or lightly increasing load torque, such as in the case of fans or low power centrifugal pumps.
Making reference to the diagram of Figure 6, the starting modality foresees the initial phase with star-connection of the windings to be realized through the closing of the circuit-breaker, of the line contactor KL and of the star contactor KY.
After a suitable predetermined period of time, the opening of the contactor KY and the closing of KΔ allow switching to delta-connection, which is also the configuration of normal running position.
[ABB]Пуск переключением со звезды на треугольник
Пуск переключением со звезды на треугольник является самым известным способом и, возможно, самой распространенной схемой пуска на пониженном напряжении. С одной стороны, этот способ используется для снижения механических нагрузок и ограничения пускового тока, а с другой - обеспечивает уменьшение пускового момента.Такая возможность может быть реализована в двигателях с шестью зажимами в выводной коробке, что позволяет питать его от двух напряжений.
Особенно этот способ подходит для ненагруженного пуска и пуска с низким постоянным или немного увеличивающимся вращающим моментом, например, для пуска вентиляторов или маломощных центробежных насосов.
Схема пуска переключением со звезды на треугольник представлена на рисунке 6. В начальный момент пуска обмотки статора соединяют звездой путем замыкания контактов автоматического выключателя, линейного контактора KL и контактора KY со схемой "звезда".
По истечении заданного времени контакты контактора KY размыкаются и замыкаются контакты контактора КΔ со схемой треугольник.
В результате выполняется переключение обмоток статора со схемы «звезда» на схему «треугольник».
Обе схемы соединения обмоток являются схемами нормального рабочего режима.
[Перевод Интент]Тематики
Обобщающие термины
EN
- star-delta starting
- Y/Δ starting
DE
FR
Русско-французский словарь нормативно-технической терминологии > пуск переключением со звезды на треугольник
-
4 wind
* -
5 прямой пуск вращающегося электродвигателя
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Русско-французский словарь нормативно-технической терминологии > прямой пуск вращающегося электродвигателя
См. также в других словарях:
thermal load — šiluminė apkrova statusas T sritis fizika atitikmenys: angl. heat load; thermal load vok. thermische Beanspruchung, f; thermische Belastung, f; Wärmebelastung, f rus. тепловая нагрузка, f pranc. charge calorifique, f; charge thermique, f … Fizikos terminų žodynas
thermal load — Смотри тепловая нагрузка … Энциклопедический словарь по металлургии
Thermal barrier coating — Thermal barrier coatings are highly advanced material systems applied to metallic surfaces, such as gas turbine or aero engine parts, operating at elevated temperatures. These coatings serve to insulate metallic components from large and… … Wikipedia
Thermal power station — Republika Power Plant, a thermal power station in Pernik, Bulgaria … Wikipedia
Thermal energy storage — District heating accumulation tower from Theiss near Krems an der Donau in Lower Austria with a thermal capacity of 2 GWh Thermal energy storage comprises a number of technologies that store thermal energy in energy storage reservoirs for later… … Wikipedia
Thermal oxidation — In microfabrication, thermal oxidation is a way to produce a thin layer of oxide (usually silicon dioxide) on the surface of a wafer (semiconductor). The technique forces an oxidizing agent to diffuse into the wafer at high temperature and react… … Wikipedia
Thermal copper pillar bump — The Thermal Copper Pillar Bump, also known as the thermal bump , is a thermoelectric device made from thin film thermoelectric material embedded in flip chip interconnects (in particular copper pillar solder bumps) for use in electronics and… … Wikipedia
Thermal (energy) Storage — A technology that lowers the amount of electricity needed for comfort conditioning during utility peak load periods. A buildings thermal energy storage system might, for example, use off peak power to make ice or to chill water at night, later… … Energy terms
heat load — šiluminė apkrova statusas T sritis fizika atitikmenys: angl. heat load; thermal load vok. thermische Beanspruchung, f; thermische Belastung, f; Wärmebelastung, f rus. тепловая нагрузка, f pranc. charge calorifique, f; charge thermique, f … Fizikos terminų žodynas
thermal (heat) load — Смотри тепловая нагрузка … Энциклопедический словарь по металлургии
Solar thermal energy — Solar thermal system for water heating in Santorini, Greece … Wikipedia