-
21 Spannungsunsymmetrie
небаланс напряжений
Отличие по модулю значения хотя бы одного из фазных или линейных напряжений многофазной системы электроснабжения от значений напряжений других фаз.
[ ГОСТ 23875-88]EN
voltage unbalance
phenomenon due to the differences between voltage deviations on the various phases, at a point of a polyphase system, resulting from differences between the phase currents or geometrical asymmetry in the line
[IEV number 604-01-29]
voltage unbalance (imbalance)
in a polyphase system, a condition in which the magnitudes of the phase voltages or the phase angles between consecutive phases are not all equal (fundamental component)
NOTE In three phase systems, the degree of inequality is usually expressed as the ratio of the negative and zero sequence components to the positive sequence component. In this technical report, voltage unbalance is considered in relation to three-phase systems and negative sequence only
[IEC 61000-3-13, ed. 1.0 (2008-02)]
voltage unbalance
condition in a polyphase system in which the r.m.s. values of the line voltages (fundamental component), and/or the phase angles between consecutive line voltages, are not all equal
NOTE 1 The degree of the inequality is usually expressed as the ratios of the negative- and zero-sequence components to the positive-sequence component.
NOTE 2 In this standard, voltage unbalance is considered in relation to 3-phase systems.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
déséquilibre des tensions d'un réseau
phénomène résultant des différences de charge ou des dissymétries géométriques de lignes et qui provoque des différences entre les écarts de tension sur les diverses phases en un point d'un réseau polyphasé
[IEV number 604-01-29]
déséquilibre de tension
dans un réseau d’énergie électrique polyphasé, état dans lequel les valeurs efficaces des tensions entre conducteurs (composante fondamentale), et/ou les différences de phase entre conducteurs successifs, ne sont pas toutes égales
NOTE 1 Le taux de déséquilibre s’exprime habituellement par le rapport de la composante inverse ou homopolaire à la composante directe.
NOTE 2 Dans la présente norme, le déséquilibre de tension est relatif aux réseaux triphasés
[IEC 61000-4-30, ed. 2.0 (2008-10)]Параллельные тексты EN-RU
Voltage unbalance
Voltage unbalance on the most unbalanced phase, displayed as a percentage of Vavg.
[Schneider Electric]Небаланс напряжений
Самое значительное отличие по модулю значения одного из линейных напряжений, выраженное в процентах от среднего напряжения Vavg.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Смотри также
Немецко-русский словарь нормативно-технической терминологии > Spannungsunsymmetrie
22 machinery
машинное оборудование
термин " машинное оборудование" означает:
- сборочную единицу, состоящую из соединенных частей или компонентов, по крайней мере, одна из которых находится в движении, имеет соответствующие приводы, схему управления, цепь питания, и т.д., соединенные вместе с целью специального применения, в частности, для производства, обработки, перемещения или упаковки материала;
- группу машин, которые для достижения той же цели организованы и управляется таким образом, что они функционируют как единое целое;
- взаимозаменяемое оборудование, модифицирующее функции машины, которое отдельно поставляется на рынок и предназначено для установки на машине или на серии различных машин или на приводном устройстве самим оператором, при условии, что данное оборудование не является запасной частью или инструментом.
[Директива 98/37/ЕЭС по машинному оборудованию]EN
machinery
‘machinery’ means:
— an assembly of linked parts or components, at least one of which moves, with the appropriate
actuators, control and power circuits, etc., joined together for a specific application, in particular
for the processing, treatment, moving or packaging of a material,
— an assembly of machines which, in order to achieve the same end, are arranged and controlled so that they function as an integral whole,
— interchangeable equipment modifying the function of a machine, which is placed on the market for the purpose of being assembled with a machine or a series of different machines or with a tractor by the operator himself in so far as this equipment is not a spare part or a tool
[DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL]Параллельные тексты EN-RU
3. The following are excluded from the scope of this Directive:
3. Из области применения данной Директивы исключаются:
— machinery whose only power source is directly applied manual effort, unless it is a machine used for lifting or lowering loads,
- машинное оборудование, для которых источником энергии является исключительно непосредственное применение ручной силы, за исключением механизмов для подъема и опускания грузов;
— machinery for medical use used in direct contact with patients,
- медицинские приборы;
— special equipment for use in fairgrounds and/or amusement parks,
- специальное оборудование для использования в аттракционах и/или парках для развлечений;
— steam boilers, tanks and pressure vessels,
- паровые котлы, резервуары и сосуды под давлением;
— machinery specially designed or put into service for nuclear purposes which, in the event of failure, may result in an emission of radioactivity,
- машинное оборудование, специально сконструированное или используемое в атомной отрасли, которые в случае аварии могут привести к выделению радиоактивных веществ;
— radioactive sources forming part of a machine,
- радиоактивные источники, составляющие часть машин;
— firearms,
- стрелковое оружие;
— storage tanks and pipelines for petrol, diesel fuel, inflammable liquids and dangerous substances,
- емкости для хранения или трубопроводы для бензина, дизельного топлива, огнеопасных жидкостей и опасных веществ;
— means of transport, i.e. vehicles and their trailers intended solely for transporting passengers by air or on road, rail or water networks, as well as means of transport in so far as such means are designed for transporting goods by air, on public road or rail networks or on water. Vehicles used in the mineral extraction industry shall not be excluded,
- транспортные средства, т.е. средства перевозки и их прицепы, предназначенные исключительно для перевозки пассажиров по воздуху, автодороге, железной дороге, или водными путями, а также транспортные средства, сконструированные для транспортировки грузов по воздуху, по общедоступным дорогам, железным дорогам или водным путям. Средства транспортировки, используемые в горнодобывающей промышленности, не исключаются из области применения настоящей Директивы;
— seagoing vessels and mobile offshore units together with equipment on board such vessels or units,
- морские суда и мобильные береговые агрегаты вместе с оборудованием на борту, такие как танки или установки;
— cableways, including funicular railways, for the public or private transportation of persons,
- канатные дороги, включая фуникулерные железные дороги для общественного или частного пользования, предназначенные для транспортировки людей;
— agricultural and forestry tractors, as defined in Article 1(1) of Directive 74/150/EEC (1),
(1) Council Directive 74/150/EEC of 4 March 1974 on the approximation of the laws of the Member States relating to the type-approval of wheeled agricultural or forestry tractors (OJ L 84, 28.3.1974, p. 10). Directive as last amended by Decision 95/1/EC, Euratom, ECSC (OJ L 1.1.1995, p. 1).-сельскохозяйственные и лесные тракторы, подпадающие под определение статьи 1 (1) Директивы Совета 74/150/ЕЭС(1);
(1) Директива Совета 74/150/ЕЭС от 4 марта 1974 г. по сближению законодательных актов Государств-членов, относящихся к одобрению типов колесных сельскохозяйственных или лесных тракторов (Официальный журнал Европейских сообществ № L 84, 28.3.1974 г., стр.10). Директива, измененная последний раз Решением 95/1/ЕЭС, Евроатом, ECSC (Официальный журнал Европейских сообществ № L 1/1/1995 г., стр 1)— machines specially designed and constructed for military or police purposes,
- машины, специально сконструированные и созданные для военных и полицейских целей;
— lifts which permanently serve specific levels of buildings and constructions, having a car moving between guides which are rigid and inclined at an angle of more than 15 degrees to the horizontal and designed for the transport of:
(i) persons;
(ii) persons and goods;
(iii) goods alone if the car is accessible, that is to say, a person may enter it without difficulty, and fitted with controls situated inside the car or within reach of a person inside,- лифты и подъемные устройства, постоянно обслуживающие определенные уровни зданий и конструкций, имеющие транспортную тележку, движущуюся между жесткими направляющими, которые имеют угол наклона более 15 градусов к горизонтальной поверхности и сконструированы для транспортировки:
(i) людей;
(ii) людей и имущества;
(iii) только имущества, в том случае, если кабина лифта открыта, т.е. человек может легко войти в такое транспортное средство и манипулировать средствами управления, находящимися внутри кабины или в пределах досягаемости для человека;— means of transport of persons using rack and pinion rail mounted vehicles,
- транспортные средства для перевозки людей, с использованием зубчатых или реечных рельс, по которым перемещается транспортные средства;
— mine winding gear,
- шахтные канатные подъемные устройства;
— theatre elevators,
- театральные подъемники;
— construction site hoists intended for lifting persons or persons and goods.
- строительные подъемники, предназначенные для подъема людей или людей и грузов.
4. Where, for machinery or safety components, the risks referred to in this Directive are wholly or partly covered by specific Community Directives, this Directive shall not apply, or shall cease to apply, in the case of such machinery or safety components and of such risks on the implementation of these specific Directives.
4. Когда для машинного оборудования и компонентов безопасности риски, определенные в настоящей Директиве, полностью или частично покрываются специальными Директивами Сообщества, настоящая Директива не применяется или прекращает свое действие, такое машинное оборудование и компоненты безопасности и такие риски подпадают под действие этих специальных Директив.
5. Where, for machinery, the risks are mainly of electrical origin, such machinery shall be covered exclusively by Directive 73/23/EEC (2).
(2) Council Directive 73/23/EEC of 19 February 1973 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (OJ L 77, 26.3.1973, p. 29). Directive as last amended by Directive 93/68/EEC (OJ L 220, 30.8.1993, p. 1).5. Когда риски применения машинного оборудования связаны с электрическими источниками, то такое оборудование охватываются исключительно Директивой 73/23/ЕЭС(2).
(2) Директива Совета 73/23/ЕЭС/ от 19 февраля 1973 года о гармонизации законов Государств-Участников в отношении электрооборудования, предназначенного для использования в условиях определенных пределов напряжения (Официальный журнал Европейских сообществ № L 77, 26.03.1973, стр. 29). Директива с последней поправкой Директивой 93/68/ЕЭС (Официальный журнал Европейских сообществ № L 220, 30.08.1993, стр.1).Article 2
1. Member States shall take all appropriate measures to ensure that machinery or safety components covered by this Directive may be placed on the market and put into service only if they do not endanger the health or safety of persons and, where appropriate, domestic animals or property, when properly installed and maintained and used for their intended purpose.Статья 2
1. Государства - члены должны предпринимать все необходимые меры для обеспечения того, чтобы машинное оборудование или компоненты безопасности, попадающие под действие настоящей Директивы, поставлялись на рынок и вводились в эксплуатацию, только если они не составляют угрозу для здоровья и безопасности людей и домашних животных, или имуществу при условии надлежащей установки и обслуживания, а также использования по прямому назначению.2. This Directive shall not affect Member States’ entitlement to lay down, in due observance of the Treaty, such requirements as they may deem necessary to ensure that persons and in particular workers are protected when using the machinery or safety components in question, provided that this does not mean that the machinery or safety components are modified in a way not specified in the Directive.
2. Настоящая Директива не ограничивает права Государств - членов устанавливать при должном соблюдении Договора такие требования, которые они посчитают необходимыми для обеспечения защиты людей, особенно работников, при использовании машинного оборудования или компонентов безопасности, при условии, что модификация такого машинного оборудования и компонентов безопасности была произведена в соответствии с положениями настоящей Директивы.
3. At trade fairs, exhibitions, demonstrations, etc., Member States shall not prevent the showing of machinery or safety components which do not conform to the provisions of this Directive, provided that a visible sign clearly indicates that such machinery or safety components do not conform and that they are not for sale until they have been brought into conformity by the manufacturer or his authorised representative established in the Community. During demonstrations, adequate safety measures shall be taken to ensure the protection of persons.
3. На торговых ярмарках, выставках, демонстрациях и т.п. Государства - члены не должны препятствовать демонстрации машинного оборудования или компонентов безопасности, которые не соответствуют положениям настоящей Директивы, при условии, что видимый знак четко указывает, что такое машинное оборудование или компоненты безопасности не соответствуют данной Директиве, и что они не предназначаются для продажи до тех пор, пока изготовитель или его уполномоченный представитель в Сообществе не приведет их в полное соответствие с Директивой. Во время демонстраций должны приниматься адекватные меры для обеспечения безопасности граждан.
Article 3
Machinery and safety components covered by this Directive shall satisfy the essential health and safety requirements set out in Annex I.Статья 3
Машинное оборудование, а также компоненты безопасности, относящиеся к области действия настоящей Директивы, должны полностью удовлетворять основным требованиям по обеспечению здоровья и безопасности, изложенным в Приложении 1.Article 4
1. Member States shall not prohibit, restrict or impede the placing on the market and putting into service in their territory of machinery and safety components which comply with this Directive.Статья 4
1. Государства - члены не должны запрещать, ограничивать или препятствовать поставке на рынок машинного оборудования, а также компонентов безопасности, которые соответствуют
требованиям настоящей Директивы.2. Member States shall not prohibit, restrict or impede the placing on the market of machinery where the manufacturer or his authorised representative established in the Community declares in accordance with point B of Annex II that it is intended to be incorporated into machinery or assembled with other machinery to constitute machinery covered by this Directive, except where it can function independently.
‘Interchangeable equipment’, as referred to in the third indent of Article 1(2)(a), must in all cases bear the CE marking and be accompanied by the EC declaration of conformity referred to in Annex II, point A.2. Государства - члены не должны запрещать, ограничивать или препятствовать поставке на рынок машинного оборудования, если изготовитель или его уполномоченный представитель в Сообществе заявляет в соответствии с Приложением II B, что они предназначены для включения в машинное оборудование или компоноваться с другим оборудованием, так, что в соединении они составят машинное оборудование, отвечающее требованиям настоящей Директивы, за исключением тех случаев, когда они могут функционировать независимо.
"Взаимозаменяемое оборудование" в смысле третьего абзаца с черточкой в Статье 1 (2) (a) должно во всех случаях иметь маркировку "СЕ" и сопровождаться декларацией соответствия, определенной в Приложении II, пункте А.3. Member States may not prohibit, restrict or impede the placing on the market of safety components as defined in Article 1(2) where they are accompanied by an EC declaration of conformity by the manufacturer or his authorised representative established in the Community as referred to in Annex II, point C.
3. Государства - члены не имеют права запрещать, ограничивать или препятствовать распространению на рынке компонентов безопасности, определенных Статьей 1 (2), если эти компоненты сопровождаются декларацией соответствия ЕС, заявленной изготовителем или его уполномоченным представителем в Сообществе, как определено в Приложении II, пункте С.
Article 5
1. Member States shall regard the following as conforming to all the provisions of this Directive, including the procedures for checking the conformity provided for in Chapter II:
— machinery bearing the CE marking and accompanied by the EC declaration of conformity referred to in Annex II, point A,
— safety components accompanied by the EC declaration of conformity referred to in Annex II, point C.Статья 5
1. Государства - члены должны считать нижеследующее соответствующим всем положениям настоящей Директивы, включая процедуры проверки соответствия, предусмотренной в Главе II:
- машинное оборудование, имеющее маркировку "СЕ" и сопровождаемое декларацией соответствия ЕС, как указано в Приложении II, пункте A;
- компоненты безопасности, сопровождаемые декларацией соответствия ЕС, как указано в Приложении II, пункте C.
При отсутствии гармонизированных стандартов Государства - члены должны предпринимать любые меры, которые они сочтут необходимыми, для привлечения внимания заинтересованных сторон к существующим национальным техническим стандартам и спецификациям, которые считаются важными или относятся к выполнению основных требований по обеспечению здоровья и безопасности в соответствии с Приложением 1.2. Where a national standard transposing a harmonised standard, the reference for which has been published in the Official Journal of the European Communities, covers one or more of the essential safety requirements, machinery or safety components constructed in accordance with this standard shall be presumed to comply with the relevant essential requirements.
Member States shall publish the references of national standards transposing harmonised standards.2. В тех случаях, когда национальный стандарт, заменяющий гармонизированный стандарт, ссылка на который была опубликована в Официальном журнале Европейских сообществ, покрывает одно или несколько основных требований безопасности, машинное оборудование или компоненты безопасности, сконструированные в соответствии с таким стандартом, должны считаться соответствующими основным требованиям.
Государства - члены должны публиковать ссылки на национальные стандарты, заменяющие гармонизированные стандарты.3. Member States shall ensure that appropriate measures are taken to enable the social partners to have an influence at national level on the process of preparing and monitoring the harmonised standards.
3. Государства - члены должны обеспечивать принятие необходимых мер для того, чтобы их социальные партнеры получали возможность влиять на национальном уровне на процессы подготовки и отслеживания гармонизированных стандартов.
Article 6
1. Where a Member State or the Commission considers that the harmonised standards referred to in Article 5(2) do not entirely satisfy the essential requirements referred to in Article 3, the Commission or the Member State concerned shall bring the matter before the committee set up under Directive 83/189/EEC, giving the reasons therefor. The committee shall deliver an opinion without delay.
Upon receipt of the committee’s opinion, the Commission shall inform the Member States whether or not it is necessary to withdraw those standards from the published information referred to in Article 5(2).Статья 6
1. В случае, если Государство - член или Комиссия считают, что гармонизированные стандарты, рассмотренные в Статье 5 (2), не полностью соответствуют основным требованиям, определенным в Статье 3, Комиссия или заинтересованное Государство - член должны поставить этот вопрос на рассмотрение комитета, созданного в соответствии с Директивой 83/189/ЕЭС, обосновав причины такого обращения. Комитет должен безотлагательно вынести решение.
После получения такого решения комитета Комиссия должна информировать Государства – члены, необходимо или нет отозвать эти стандарты из опубликованной информации, определенной в Статье 5 (2).2. A standing committee shall be set up, consisting of representatives appointed by the Member States and chaired by a representative of the Commission.
The standing committee shall draw up its own rules of procedure.
Any matter relating to the implementation and practical application of this Directive may be brought before the standing committee, in accordance with the following procedure:
The representative of the Commission shall submit to the committee a draft of the measures to be taken. The committee shall deliver its opinion on the draft, within a time limit which the chairman may lay down according to the urgency of the matter, if necessary by taking a vote.
The opinion shall be recorded in the minutes; in addition, each Member State shall have the right to ask to have its position recorded in the minutes.
The Commission shall take the utmost account of the opinion delivered by the committee.
It shall inform the committee of the manner in which its opinion has been taken into account.2. Должен быть создан постоянно действующий комитет, состоящий из представителей, назначенных Государствами – членами, и возглавляемый представителем Комиссии.
Постоянно действующий комитет будет сам устанавливать порядок действий и процедуры.
Любой вопрос, относящийся к выполнению и практическому применению настоящей Директивы, может быть поставлен на рассмотрение постоянно действующего комитета, в соответствии со следующими правилами:
Представитель Комиссии должен представить комитету проект предполагаемых к принятию мер. Комитет должен выразить свое мнение по проекту за время, установленное председателем в соответствии со срочностью вопроса, при необходимости определяемого путем голосования.
Это мнение должно быть зафиксировано в протоколе; кроме того, каждое Государство - член имеет право потребовать отразить свою позицию в протоколе. Комиссия должна максимально учитывать мнение, вынесенное комитетом.
Она должна проинформировать комитет, каким образом было учтено его мнение.Article 7
1. Where a Member State ascertains that:
— machinery bearing the CE marking, or
— safety components accompanied by the EC declaration of conformity, used in accordance with their intended purpose are liable to endanger the safety of persons, and, where appropriate, domestic animals or property, it shall take all appropriate measures to withdraw such machinery or safety components from the market, to prohibit the placing on the market, putting into service or use thereof, or to restrict free movement thereof.
Member States shall immediately inform the Commission of any such measure, indicating the reason for its decision and, in particular, whether non-conformity is due to:
(a) failure to satisfy the essential requirements referred to in Article 3;
(b) incorrect application of the standards referred to in Article 5(2);
(c) shortcomings in the standards themselves referred to in Article 5(2).Статья 7
1. Если Государство - член устанавливает, что:
- машинное оборудование, имеющее маркировку "СЕ", либо
- компоненты безопасности, сопровождаемые декларацией соответствия ЕС, используемые в соответствии с их назначением, могут нести угрозу безопасности людям, и, если это имеет место, домашним животным или собственности, оно должно принять все необходимые меры для изъятия такого машинного оборудования, либо компонентов безопасности с рынка, запретить их поставку на рынок, ввод в эксплуатацию или использование, либо ограничить их свободное обращение.
Государства - члены должны немедленно информировать Комиссию о любых подобных мерах, указать причины такого решения и, в особенности, информировать о том, явилось ли это несоответствие результатом:
a) неспособности удовлетворить основным требованиям, определенным в Статье 3;
b) неправильного применения стандартов, определенных в Статье 5 (п.2);
c) недостатков самих стандартов, определенных в Статье 5 (п. 2).2. The Commission shall enter into consultation with the parties concerned without delay. Where the Commission considers, after this consultation, that the measure is justified, it shall immediately so inform the Member State which took the initiative and the other Member States. Where the Commission considers, after this consultation, that the action is unjustified, it shall immediately so inform the Member State which took the initiative and the manufacturer or his authorised representative established within the Community.
Where the decision referred to in paragraph 1 is based on a shortcoming in the standards, and where the Member State at the origin of the decision maintains its position, the Commission shall immediately inform the committee in order to initiate the procedures referred to in Article 6(1).2. Комиссия должна безотлагательно провести консультацию с заинтересованными сторонами. В случае, если после проведения такой консультации, Комиссия полагает, что такая мера обоснована, она должна немедленно информировать об этом Государство - член, которое выдвинуло эту инициативу, а также остальные Государства - члены. Если Комиссия после проведения такой консультации полагает, что действия не были обоснованными, она немедленно извещает об этом Государство - член, проявившее инициативу, и изготовителя, либо его уполномоченного представителя в Сообществе.
Если решение, указанное в параграфе 1, основано на недостатках в стандартах, и если Государство - член на основании такого решения сохраняет свои позиции, то Комиссия должна немедленно информировать комитет для того, чтобы начать процедуры, описанные в Статье 6 (п. 1).3. Where:
— machinery which does not comply bears the CE marking,
— a safety component which does not comply is accompanied by an EC declaration of conformity,
the competent Member State shall take appropriate action against whom so ever has affixed the marking or drawn up the declaration and shall so inform the Commission and other Member States.3. Если:
- машинное оборудование, не соответствующие требованиям, имеют маркировку "СЕ",
- компоненты безопасности, не соответствующие требованиям, имеют декларацию соответствия ЕС,
компетентное Государство - член должно начать соответствующие действия против любого, кто поставил маркировку, или составил декларацию, и должно проинформировать об этом Комиссию и другие Государства - члены.4. The Commission shall ensure that Member States are kept informed of the progress and outcome of this procedure.
4. Комиссия должна обеспечить, чтобы Государства – члены были постоянно информированы о ходе и результатах данной процедуры.
CHAPTER II
CONFORMITY ASSESSMENT PROCEDURES
Article 8
1. The manufacturer or his authorised representative established in the Community must, in order to certify that machinery and safety components are in conformity with this Directive, draw up for all machinery or safety components manufactured an EC declaration of conformity based on the model given in Annex II, point A or C as appropriate.
In addition, for machinery alone, the manufacturer or his authorised representatives established in the Community must affix to the machine the CE marking.Глава II
Процедуры оценки соответствия
Статья 8
1. Для подтверждения того, что машинное оборудование, а также компоненты безопасности соответствуют положениям настоящей Директивы, изготовитель или его уполномоченный представитель в Сообществе должен составить декларацию ЕС о соответствии на произведенное машинное оборудование и компоненты безопасности по образцу, приведенному в Приложении II, соответственно пунктам A или C.
Корме того, на машинное оборудование изготовитель или его уполномоченный представитель в Сообществе должен нанести маркировку "СЕ" в соответствии со Статьей 10.2. Before placing on the market, the manufacturer, or his authorised representative established in the Community, shall:
(a) if the machinery is not referred to in Annex IV, draw up the file provided for in Annex V;
(b) if the machinery is referred to in Annex IV and its manufacturer does not comply, or only partly complies, with the standards referred to in Article 5(2) or if there are no such standards, submit an example of the machinery for the EC type-examination referred to in Annex VI;
(c) if the machinery is referred to in Annex IV and is manufactured in accordance with the standards referred to in Article 5(2):
— either draw up the file referred to in Annex VI and forward it to a notified body, which will acknowledge receipt of the file as soon as possible and keep it,
— submit the file referred to in Annex VI to the notified body, which will simply verify that the standards referred to in Article 5(2) have been correctly applied and will draw up a certificate of adequacy for the file,
— or submit the example of the machinery for the EC type-examination referred to in Annex VI.2. Перед поставкой на рынок изготовитель или его уполномоченный представитель в Сообществе должен:
(a) в случае, если машинное оборудование не указано в Приложении IV, составить документацию, предусмотренную Приложением V;
(b) если машинное оборудование указано в Приложении IV, и их изготовитель не выполняет, либо выполняет лишь частично требования стандартов, упомянутых в Статье 5 (2), либо, если таких стандартов не существует, то представить образец машинного оборудования для его испытания ЕС, определенного в Приложении VI;
(c) если машинное оборудование указано в Приложении IV и изготовлено в соответствии со стандартами, определенными в Статье 5 (п. 2):
- либо составить документацию, указанную в Приложении VI, и передать ее нотифицированному органу, который подтверждает получение документации в возможно короткие сроки, а также сохраняет ее;
- представить документацию, указанную в Приложении VI, нотифицированному органу, который просто проверит, что стандарты, упомянутые в Статье 5 (2), были применены правильно и составит сертификат соответствия по этой документации;
- либо представить образец машинного оборудования для испытания ЕС типового образца, определенного в Приложении VI.3. Where the first indent of paragraph 2(c) of this Article applies, the provisions of the first sentence of paragraphs 5 and 7 of Annex VI shall also apply.
Where the second indent of paragraph 2(c) of this Article applies, the provisions of paragraphs 5, 6 and 7 of Annex VI shall also apply.3. В тех случаях, когда может быть применен первый абзац параграфа 2 (с) этой Статьи должны также применяться положения первого предложения параграфов 5 и 7 Приложения VI.
В тех случаях, когда может быть применен второй абзац пункта 2 (с), должны также применяться положения параграфов 5, 6 и 7 Приложения VI.4. Where paragraph 2(a) and the first and second indents of paragraph 2(c) apply, the EC declaration of conformity shall solely state conformity with the essential requirements of the Directive.
Where paragraph 2(b) and the third indent of paragraph 2(c) apply, the EC declaration of conformity shall state conformity with the example that underwent EC type-examination.4. В тех случаях, когда применяется параграф 2 (а) и первый и второй абзацы параграфа 2 (c), декларация ЕС о соответствии должна удостоверить соответствие основным требованиям настоящей Директивы.
В случае, когда применяется параграф 2 (b) и третий абзац параграфа 2 (c), декларация ЕС о соответствии должна удостоверить соответствие образцу, прошедшему испытание ЕС типового образца.5. Safety components shall be subject to the certification procedures applicable to machinery pursuant to paragraphs 2, 3 and 4. Furthermore, during EC type-examination, the notified body shall verify the suitability of the safety component for fulfilling the safety functions declared by the manufacturer.
5.Компоненты безопасности должны подвергаться процедурам сертификации, применимым к машинному оборудованию в соответствии с параграфами 2, 3, 4. Более того, во время испытания ЕС типового образца нотифицированный орган должен проверить пригодность компонентов безопасности для выполнения тех функций безопасности, которые заявлены изготовителем.
6. (a) Where the machinery is subject to other Directives concerning other aspects and which also provide for the affixing of the CE marking, the latter shall indicate that the machinery is also presumed to conform to the provisions of those other Directives.
(b) However, where one or more of those Directives allow the manufacturer, during a transitional period, to choose which arrangements to apply, the CE marking shall indicate conformity only to the Directives applied by the manufacturer. In this case, particulars of the Directives applied, as published in the Official Journal of the European Communities, must be given in the documents, notices or instructions required by the directives and accompanying such machinery.6. (a) В тех случаях, когда машинное оборудование подпадает под действие Директив по другим аспектам, которые также предусматривают нанесение маркировки "СЕ", последняя указывает, что такое машинное оборудование соответствуют положениям этих прочих директив.
(b) Тем не менее, когда одна или несколько таких Директив позволяют изготовителям в течение переходного периода выбирать, какие из положений применить, маркировка "СЕ" будет указывать на соответствие только тем Директивам, которые применялись изготовителем. В этом случае подробная информация о примененных Директивах, опубликованных в Официальном журнале Европейских сообществ, должен приводиться в документах, аннотациях или инструкциях, требуемых в соответствии с Директивами, и сопровождать такое машинное оборудование.7. Where neither the manufacturer nor his authorised representative established in the Community fulfils the obligations of paragraphs 1 to 6, these obligations shall fall to any person placing the machinery or safety component on the market in the Community. The same obligations shall apply to any person assembling machinery or parts thereof or safety components of various origins or constructing machinery or safety components for his own use.
7. Если ни изготовитель, ни его уполномоченный представитель в Сообществе не выполнят своих обязательств по предыдущим параграфам, то эти обязательства должны быть выполнены любыми лицами, поставляющими машинное оборудование или компоненты безопасности на рынок Сообщества. Такие же обязательства возлагаются на любые лица, осуществляющие сборку машинного оборудования, либо его частей или компонентов безопасности различного происхождения, либо создающие машинное оборудование или компоненты безопасности для собственного пользования.
8. The obligations referred to in paragraph 7 shall not apply to persons who assemble with a machine or tractor interchangeable equipment as provided for in Article 1, provided that the parts are compatible and each of the constituent parts of the assembled machine bears the CE marking and is accompanied by the EC declaration of conformity.
8. Обязательства, изложенные в параграфе 7, не применяются к лицам, которые собирают с машиной, механизмом или транспортным средством взаимозаменяемое оборудование, указанное в Статье 1, при условии, что эти части совместимы, и каждая из частей машины в сборе имеет маркировку "СЕ" и Декларацию ЕС о соответствии.
Article 9
1. Member States shall notify the Commission and the other Member States of the approved bodies which they have appointed to carry out the procedures referred to in Article 8 together with the specific tasks which these bodies have been appointed to carry out and the identification numbers assigned to them beforehand by the Commission.
The Commission shall publish in the Official Journal of the European Communities a list of the notified bodies and their identification numbers and the tasks for which they have been notified. The Commission shall ensure that this list is kept up to date.Статья 9
1. Государства - члены должны уведомить Комиссию и другие Государства - члены об утвержденных органах, которые назначаются для выполнения процедур, описанных в Статье 8, также как и для различных особых задач, которые этим органам предназначено выполнять, и об идентификационных номерах, предварительно присвоенных им Комиссией.В Официальном журнале Европейских сообществ Комиссия должна публиковать список таких нотифицированных органов и их идентификационные номера, а также задачи, для решения которых они предназначены. Комиссия должна обеспечить своевременность обновления списка.
2. Member States shall apply the criteria laid down in Annex VII in assessing the bodies to be indicated in such notification. Bodies meeting the assessment criteria laid down in the relevant harmonised standards shall be presumed to fulfil those criteria.
2. Государства - члены должны применять критерии, изложенные в Приложении VII, для определения органов, которые будут указаны в таких назначениях. Органы, удовлетворяющие критериям, изложенным в соответствующих гармонизированных стандартах, считаются соответствующими критериям.
3. A Member State which has approved a body must withdraw its notification if it finds that the body no longer meets the criteria referred to in Annex VII. It shall immediately inform the Commission and the other Member States accordingly.
3. Государство - член, утвердившее такой орган, должно отменить его назначение, если оно обнаружит, что он больше не соответствует критериям, изложенным в Приложении VII. Государство - член должно немедленно известить об этом Комиссию и другие Государства - члены.
CHAPTER III
CE MARKING
Article 10
1. The CE conformity marking shall consist of the initials ‘CE’. The form of the marking to be used is shown in Annex III.ГЛАВА III
МАРКИРОВКА "СЕ"
Статья 10
1. Маркировка "СЕ" состоит из заглавных букв "СЕ". Форма маркировки, которая будет использоваться, указана в Приложении III.2. The CE marking shall be affixed to machinery distinctly and visibly in accordance with point 1.7.3 of Annex I.
2. Маркировка "СЕ" должна наноситься на машинное оборудование четко, на видном месте в соответствии с пунктом 1.7.3. Приложения I.
3. The affixing of markings on the machinery which are likely to deceive third parties as to the meaning and form of the CE marking shall be prohibited. Any other marking may be affixed to the machinery provided that the visibility and legibility of the CE marking is not thereby reduced.
3. Нанесение маркировок на машинное оборудование таким образом, что это может ввести в заблуждение относительно значения и формы маркировки "СЕ", запрещено. Любые другие маркировки могут быть нанесены на машинное оборудование таким образом, чтобы не мешать видимости и различимости маркировки "СЕ".
4. Without prejudice to Article 7:
(a) where a Member State establishes that the CE marking has been affixed unduly, the manufacturer or his authorised representative established within the Community shall be obliged to make the product conform as regards the provisions concerning the CE marking and to end the infringement under the conditions imposed by the Member State;
(b) where non-conformity continues, the Member State must take all appropriate measures to restrict or prohibit the placing on the market of the product in question or to ensure that it is withdrawn from the market in accordance with the procedure laid down in Article 7.4. Без ограничения применения Статьи 7:
(a) если Государство - член устанавливает, что маркировка "СЕ" была нанесена неправильно, изготовитель или его уполномоченный представитель в Сообществе будет обязан привести продукцию в соответствии с положениями, касающимися маркировки "СЕ" и положить конец нарушениям на условиях, установленных Государством - членом;
(b) если такое несоответствие будет продолжаться, то Государство - член должно принять все соответствующие меры для ограничения или запрещения поставки на рынок такой продукции, либо обеспечить изъятие ее с рынка в соответствии с процедурами, изложенными в Статье 7.CHAPTER IV
FINAL PROVISIONS
Article 11
Any decision taken pursuant to this Directive which restricts the placing on the market and putting into service of machinery or a safety component shall state the exact grounds on which it is based. Such a decision shall be notified as soon as possible to the party concerned, who shall at the same time be informed of the legal remedies available to him under the laws in force in the Member State concerned and of the time limits to which such remedies are subject.ГЛАВА IV
ЗАКЛЮЧИТЕЛЬНЫЕ ПОЛОЖЕНИЯ
Статья 11
Любое решение, принятое в исполнение настоящей Директивы, ограничивающее поставку на рынок и ввод в эксплуатацию машинного оборудования или компонентов безопасности, должно указывать точные причины, на которых оно основано. Такое решение должно быть по возможности быстро доведено до сведения заинтересованных сторон, их также следует проинформировать о законных мерах, которые могут быть предприняты по действующему законодательству в соответствующем Государстве - члене и о сроках, в которые данные меры применяются.Article 12
The Commission will take the necessary steps to have information on all the relevant decisions relating to the management of this Directive made available.Статья 12
Комиссия предпримет все необходимые шаги для получения информации по всем соответствующим решениям, касающимся применения и распространения настоящей Директивы.Article 13
1. Member States shall communicate to the Commission the texts of the provisions of national law which they adopt in the field governed by this Directive.
2. The Commission shall, before 1 January 1994, examine the progress made in the standardisation work relating to this Directive and propose any appropriate measures.Статья 13
1. Государства - члены должны передать Комиссии тексты положений национальных законодательных актов, принимаемых в сфере, определяемой настоящей Директивой.
2. Комиссия должна до 1 января 1994 г. изучить развитие работ по стандартизации, относящиеся к области действия настоящей Директивы и предложить любые целесообразные меры.Тематики
EN
машины
оборудование
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва]
машины
Машина представляет собой аппарат, использующий или применяющий механическую энергию, состоящий из нескольких частей — каждая со своими определенными функциями, которые вместе выполняют некоторые виды работ. Для целей анализа это понятие включает отдельные машины или наборы машин. См. Машины и оборудование (МСО)
[ http://slovar-lopatnikov.ru/]Тематики
- экономика
- электротехника, основные понятия
Синонимы
EN
машины и оборудование
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]
машины и оборудование
МСО
Часть основных фондов компании (предприятия), которая включает устройства, преобразующие энергию, материалы и информацию. В аналитической и оценочной практике в общее понятие М. и о. включаются отдельно оцениваемые установки, машины, оборудование и транспортные средства, подразделяемые на виды, а каждый вид – на марки (последним термином для краткости можно обозначать разные модели и модификации машины). Разные марки машин одного вида используются для одних и тех же целей: они способны производить одну и ту же продукцию, выполнять одни и те же работы или оказывать одни и те же услуги ( в противном случае их надо относить в другому виду машин), а следовательно, «взаимозаменяемы» и являются товарами, конкурирующими между собой на рынке Рынок машин каждого вида делится на первичный (новые М..) и вторичный (бывшие в эксплуатации), для которых применяются разные оценочные приемы и инструменты.. М.и о. являются главным объектом инвестирования при разработке и реализации инвестиционного проекта, и, соответственно, одним из основных элементов оценки инвестиционных проектов. Важно, что в отличие от ценных бумаг, акций, М.и о. являются объектами реальных инвестиций, а не финансовых инвестиций.
[ http://slovar-lopatnikov.ru/]EN
machinery
A group of parts or machines arranged to perform a useful function. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
Синонимы
EN
DE
FR
механизм
Совокупность подвижно соединённых звеньев, совершающих под действием приложенных сил заранее определённые целесообразные движения
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]
машины, механизмы
Совокупность связанных между собой частей и устройств, как минимум одно из которых движется, имеет соответствующий привод, органы управления и энергетические узлы, соединенные вместе для определенного применения, например для обработки, переработки, производства, транспортирования или упаковки материалов.
Термины «машина» и «механизм» также распространяются на совокупность машин, которые размещаются и управляются таким образом, чтобы функционировать как единое целое.
Примечание
В приложении А приведено общее схематическое изображение машины.
[ ГОСТ Р ИСО 12100-1:2007]EN
DE
FR
оборудование
оборудование
Совокупность связанных между собой частей или устройств, из которых по крайней мере одно движется, а также элементы привода, управления и энергетические узлы, которые предназначены для определенного применения, в частности для обработки, производства, перемещения или упаковки материала. К термину «оборудование» относят также машину и совокупность машин, которые так устроены и управляемы, что они функционируют как единое целое для достижения одной и той же цели.
[ГОСТ ЕН 1070-2003]
-
[IEV number 151-11-25 ]
оборудование
Оснащение, материалы, приспособления, устройства, механизмы, приборы, инструменты и другие принадлежности, используемые в качестве частей электрической установки или в соединении с ней.
[ ГОСТ Р МЭК 60204-1-2007]EN
equipment
single apparatus or set of devices or apparatuses, or the set of main devices of an installation, or all devices necessary to perform a specific task
NOTE – Examples of equipment are a power transformer, the equipment of a substation, measuring equipment.
[IEV number 151-11-25 ]
equipment
material, fittings, devices, components, appliances, fixtures, apparatus, and the like used as part of, or in connection with, the electrical equipment of machines
[IEC 60204-1-2006]FR
équipement, m
matériel, m
appareil unique ou ensemble de dispositifs ou appareils, ou ensemble des dispositifs principaux d'une installation, ou ensemble des dispositifs nécessaires à l'accomplissement d'une tâche particulière
NOTE – Des exemples d’équipement ou de matériel sont un transformateur de puissance, l’équipement d’une sous-station, un équipement de mesure.
[IEV number 151-11-25]Тематики
EN
- accessories
- apparatus
- appliance
- assets
- environment
- equipment
- facility
- fitment
- fixing
- gear
- H/W
- hardware
- hardware environment
- HW
- installation
- instrument
- instrumentation
- layout
- machinery
- outfit
- paraphernalia
- plant
- plant stock
- product
- provisions
- rig
- rigging
- set-up
- stock-in-trade
- tackle
- technical equipment
- technique
DE
FR
- machine
- matériel, m
- équipement, m
организационный аппарат
—
[ http://www.iks-media.ru/glossary/index.html?glossid=2400324]Тематики
- электросвязь, основные понятия
EN
3.26 машины (machinery): Устройство, состоящее из соединенных между собой частей или компонентов, по крайней мере, один из которых движется, с соответствующими исполнительными механизмами, силовыми цепями и цепями управления и т.д., объединенных вместе в целях конкретного применения, в частности, для обработки, переработки, перемещения или упаковки материала (материал означает эквивалент вещества или изделия).
Термин «машины» одновременно означает совокупность машин и механизмов, которые для достижения одной и той же цели установлены и управляются таким образом, что они функционируют как единое целое.
Англо-русский словарь нормативно-технической терминологии > machinery
23 imbalance in the voltages
небаланс напряжений
Отличие по модулю значения хотя бы одного из фазных или линейных напряжений многофазной системы электроснабжения от значений напряжений других фаз.
[ ГОСТ 23875-88]EN
voltage unbalance
phenomenon due to the differences between voltage deviations on the various phases, at a point of a polyphase system, resulting from differences between the phase currents or geometrical asymmetry in the line
[IEV number 604-01-29]
voltage unbalance (imbalance)
in a polyphase system, a condition in which the magnitudes of the phase voltages or the phase angles between consecutive phases are not all equal (fundamental component)
NOTE In three phase systems, the degree of inequality is usually expressed as the ratio of the negative and zero sequence components to the positive sequence component. In this technical report, voltage unbalance is considered in relation to three-phase systems and negative sequence only
[IEC 61000-3-13, ed. 1.0 (2008-02)]
voltage unbalance
condition in a polyphase system in which the r.m.s. values of the line voltages (fundamental component), and/or the phase angles between consecutive line voltages, are not all equal
NOTE 1 The degree of the inequality is usually expressed as the ratios of the negative- and zero-sequence components to the positive-sequence component.
NOTE 2 In this standard, voltage unbalance is considered in relation to 3-phase systems.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
déséquilibre des tensions d'un réseau
phénomène résultant des différences de charge ou des dissymétries géométriques de lignes et qui provoque des différences entre les écarts de tension sur les diverses phases en un point d'un réseau polyphasé
[IEV number 604-01-29]
déséquilibre de tension
dans un réseau d’énergie électrique polyphasé, état dans lequel les valeurs efficaces des tensions entre conducteurs (composante fondamentale), et/ou les différences de phase entre conducteurs successifs, ne sont pas toutes égales
NOTE 1 Le taux de déséquilibre s’exprime habituellement par le rapport de la composante inverse ou homopolaire à la composante directe.
NOTE 2 Dans la présente norme, le déséquilibre de tension est relatif aux réseaux triphasés
[IEC 61000-4-30, ed. 2.0 (2008-10)]Параллельные тексты EN-RU
Voltage unbalance
Voltage unbalance on the most unbalanced phase, displayed as a percentage of Vavg.
[Schneider Electric]Небаланс напряжений
Самое значительное отличие по модулю значения одного из линейных напряжений, выраженное в процентах от среднего напряжения Vavg.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Смотри также
Англо-русский словарь нормативно-технической терминологии > imbalance in the voltages
24 unbalance voltage
небаланс напряжений
Отличие по модулю значения хотя бы одного из фазных или линейных напряжений многофазной системы электроснабжения от значений напряжений других фаз.
[ ГОСТ 23875-88]EN
voltage unbalance
phenomenon due to the differences between voltage deviations on the various phases, at a point of a polyphase system, resulting from differences between the phase currents or geometrical asymmetry in the line
[IEV number 604-01-29]
voltage unbalance (imbalance)
in a polyphase system, a condition in which the magnitudes of the phase voltages or the phase angles between consecutive phases are not all equal (fundamental component)
NOTE In three phase systems, the degree of inequality is usually expressed as the ratio of the negative and zero sequence components to the positive sequence component. In this technical report, voltage unbalance is considered in relation to three-phase systems and negative sequence only
[IEC 61000-3-13, ed. 1.0 (2008-02)]
voltage unbalance
condition in a polyphase system in which the r.m.s. values of the line voltages (fundamental component), and/or the phase angles between consecutive line voltages, are not all equal
NOTE 1 The degree of the inequality is usually expressed as the ratios of the negative- and zero-sequence components to the positive-sequence component.
NOTE 2 In this standard, voltage unbalance is considered in relation to 3-phase systems.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
déséquilibre des tensions d'un réseau
phénomène résultant des différences de charge ou des dissymétries géométriques de lignes et qui provoque des différences entre les écarts de tension sur les diverses phases en un point d'un réseau polyphasé
[IEV number 604-01-29]
déséquilibre de tension
dans un réseau d’énergie électrique polyphasé, état dans lequel les valeurs efficaces des tensions entre conducteurs (composante fondamentale), et/ou les différences de phase entre conducteurs successifs, ne sont pas toutes égales
NOTE 1 Le taux de déséquilibre s’exprime habituellement par le rapport de la composante inverse ou homopolaire à la composante directe.
NOTE 2 Dans la présente norme, le déséquilibre de tension est relatif aux réseaux triphasés
[IEC 61000-4-30, ed. 2.0 (2008-10)]Параллельные тексты EN-RU
Voltage unbalance
Voltage unbalance on the most unbalanced phase, displayed as a percentage of Vavg.
[Schneider Electric]Небаланс напряжений
Самое значительное отличие по модулю значения одного из линейных напряжений, выраженное в процентах от среднего напряжения Vavg.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Смотри также
Англо-русский словарь нормативно-технической терминологии > unbalance voltage
25 voltage imbalance
небаланс напряжений
Отличие по модулю значения хотя бы одного из фазных или линейных напряжений многофазной системы электроснабжения от значений напряжений других фаз.
[ ГОСТ 23875-88]EN
voltage unbalance
phenomenon due to the differences between voltage deviations on the various phases, at a point of a polyphase system, resulting from differences between the phase currents or geometrical asymmetry in the line
[IEV number 604-01-29]
voltage unbalance (imbalance)
in a polyphase system, a condition in which the magnitudes of the phase voltages or the phase angles between consecutive phases are not all equal (fundamental component)
NOTE In three phase systems, the degree of inequality is usually expressed as the ratio of the negative and zero sequence components to the positive sequence component. In this technical report, voltage unbalance is considered in relation to three-phase systems and negative sequence only
[IEC 61000-3-13, ed. 1.0 (2008-02)]
voltage unbalance
condition in a polyphase system in which the r.m.s. values of the line voltages (fundamental component), and/or the phase angles between consecutive line voltages, are not all equal
NOTE 1 The degree of the inequality is usually expressed as the ratios of the negative- and zero-sequence components to the positive-sequence component.
NOTE 2 In this standard, voltage unbalance is considered in relation to 3-phase systems.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
déséquilibre des tensions d'un réseau
phénomène résultant des différences de charge ou des dissymétries géométriques de lignes et qui provoque des différences entre les écarts de tension sur les diverses phases en un point d'un réseau polyphasé
[IEV number 604-01-29]
déséquilibre de tension
dans un réseau d’énergie électrique polyphasé, état dans lequel les valeurs efficaces des tensions entre conducteurs (composante fondamentale), et/ou les différences de phase entre conducteurs successifs, ne sont pas toutes égales
NOTE 1 Le taux de déséquilibre s’exprime habituellement par le rapport de la composante inverse ou homopolaire à la composante directe.
NOTE 2 Dans la présente norme, le déséquilibre de tension est relatif aux réseaux triphasés
[IEC 61000-4-30, ed. 2.0 (2008-10)]Параллельные тексты EN-RU
Voltage unbalance
Voltage unbalance on the most unbalanced phase, displayed as a percentage of Vavg.
[Schneider Electric]Небаланс напряжений
Самое значительное отличие по модулю значения одного из линейных напряжений, выраженное в процентах от среднего напряжения Vavg.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Смотри также
неуравновешенность напряжений
асимметрия напряжений (многофазной системы)
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999]Тематики
- электротехника, основные понятия
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > voltage imbalance
26 CTI
1) Военный термин: command technical inspection, complaint-type investigation, contract technical instructor2) Техника: color transient improvement, communications technician I, communications technician intercept radioman, conductivity-temperature indicator, controlled time interval3) Химия: Charge Transfer Inefficiency4) Телекоммуникации: Computer Telephony Integration5) Сокращение: Central Technical Institute, Central Tyre Inflation, Component Test Instruction, Comprehensive Technologies International Inc. (USA), Critical Technologies Institute, Computers in Teaching Initiative6) Университет: Collegiate Training Initiative, Columbus Technical Institute7) Электроника: Cycle Time Improvement8) Вычислительная техника: Channel Terminal Interconnector, Computational Testbed for Industry, объединение компьютерных и телефонных систем9) Холодильная техника: Cooling Tower Institute10) Деловая лексика: Complete And Total Integration11) Бурение: coiled tubing injector, coiled tubing injector unit12) Образование: Computers Teaching Initiative13) Сетевые технологии: computer-telephony integration, computer/telephone integration14) Полимеры: cyclohexane triisocyanate15) Пластмассы: Comparative Tracking Index16) Нефть и газ: колтюбинговый инжектор17) МИД: Committee on Trade and Investment18) Электротехника: сравнительный индекс трекингостойкости, СИТ (Comparative Tracking Index)19) Hi-Fi. Color Transition Improvement20) NYSE. Chart Industries, Inc.21) Программное обеспечение: Computer Telephony Interface22) Международная торговля: Customer Trade Indicator27 TCR
1) Общая лексика: hum. сокр. T Cell Receptor2) Компьютерная техника: The Computer Room, Transmission Confirmation Report3) Спорт: Team Crash Racing4) Военный термин: Tactical Control Room, Time Critical Requirements, Transfer Control Record, Transportation Corps release, technical change request, technical characteristics review, technical compliance record, terrain clearance radar, terrain-closure rate, test condition requirements, traffic control radar5) Техника: tab card reader, target-to clutter ratio, telemetry compression routine, temperature coefficient of reactivity, temperature control reference, temperature-controlled room, thermofor catalytic reforming, time code reader, time constant regulator, transfer control register, two-color radiometer, Термический коэффициент сопротивления (Thermal Coefficient of Resistivity)6) Оптика: temperature coefficient of resistance7) Сокращение: Tracer8) Генетика: ГЕНОМНАЯ ОРГАНИЗАЦИЯ T-КЛЕТОЧНЫХ РЕЦЕПТОРОВ9) Иммунология: T Cell Receptor10) Банковское дело: Transaction Component Records11) Полимеры: technically classified rubber12) Полупроводники: temperature coefficient of resistivity13) Энергосистемы: theoretical capacity remuneration14) Электротехника: thyristor controlled reactor, thyristor controlled rectifier15) Чат: Twentieth Century Romeo16) NYSE. Cornerstone Realty Income Trust I28 TSC
1) Компьютерная техника: Telecom Signaling Card3) Военный термин: TROJAN Switching Center, Tactical Support Company, Top Secret Club, Top Secret Control, Troop Support Command, tactical satellite communications, tactical support center, target selection confusion, technical subcommittee, terminal service company, test steering committee, test support controller, total system control, training support center4) Техника: target signature classification, telephone signaling converter, television scan converter, test set computer, thermally stimulated conductivity, time sharing control task, total soluble cations, totally self-checking system, transportable communications system, twisted smectic c-phase5) Сельское хозяйство: Tractor Sales Corporation6) Религия: Texas Soul Clinic7) Юридический термин: sign a contract8) Бухгалтерия: True Stranded Costs9) Астрономия: Thermally Stimulated Currents10) Металлургия: thin slab caster11) Телекоммуникации: Test System Controller12) Сокращение: Tactical Support Centre, Technical Support Center, Theater Surface Combatant, Total Ship Computer (system), Total Ship Computing, Transport Support Command, Triple Store Carrier, термоструктурные композиты (Thermostructural Composites)13) Университет: Taggart Student Center14) Физиология: Thermal Shock Chamber, Triage Station Controller, Tuberous Sclerosis Complex15) Вычислительная техника: Triton System Component, Triton System Controller, transmitter start code, Time Stamp Counter (Intel), Triton System Controller (Intel, Triton, IC)16) Транспорт: Transportable Storage Canister, Two Stroke Cycle17) Фирменный знак: The Service Center, The Service Company, Tractor Supply Company18) СМИ: The Space Channel19) Деловая лексика: Time Stamp Counter20) Производство: total annual stocking cost21) Полимеры: thermal stress cracking, total solids concentration22) Океанография: Transportation Systems Center23) Расширение файла: Time Sharing Control24) Нефть и газ: ТПК - Технический подкомитет (Technical subcommittee)25) Электротехника: thermally stimulated current, thyristor switched capacitors26) Майкрософт: счётчик метки времени27) AMEX. Stephan Company29 Tsc
1) Компьютерная техника: Telecom Signaling Card3) Военный термин: TROJAN Switching Center, Tactical Support Company, Top Secret Club, Top Secret Control, Troop Support Command, tactical satellite communications, tactical support center, target selection confusion, technical subcommittee, terminal service company, test steering committee, test support controller, total system control, training support center4) Техника: target signature classification, telephone signaling converter, television scan converter, test set computer, thermally stimulated conductivity, time sharing control task, total soluble cations, totally self-checking system, transportable communications system, twisted smectic c-phase5) Сельское хозяйство: Tractor Sales Corporation6) Религия: Texas Soul Clinic7) Юридический термин: sign a contract8) Бухгалтерия: True Stranded Costs9) Астрономия: Thermally Stimulated Currents10) Металлургия: thin slab caster11) Телекоммуникации: Test System Controller12) Сокращение: Tactical Support Centre, Technical Support Center, Theater Surface Combatant, Total Ship Computer (system), Total Ship Computing, Transport Support Command, Triple Store Carrier, термоструктурные композиты (Thermostructural Composites)13) Университет: Taggart Student Center14) Физиология: Thermal Shock Chamber, Triage Station Controller, Tuberous Sclerosis Complex15) Вычислительная техника: Triton System Component, Triton System Controller, transmitter start code, Time Stamp Counter (Intel), Triton System Controller (Intel, Triton, IC)16) Транспорт: Transportable Storage Canister, Two Stroke Cycle17) Фирменный знак: The Service Center, The Service Company, Tractor Supply Company18) СМИ: The Space Channel19) Деловая лексика: Time Stamp Counter20) Производство: total annual stocking cost21) Полимеры: thermal stress cracking, total solids concentration22) Океанография: Transportation Systems Center23) Расширение файла: Time Sharing Control24) Нефть и газ: ТПК - Технический подкомитет (Technical subcommittee)25) Электротехника: thermally stimulated current, thyristor switched capacitors26) Майкрософт: счётчик метки времени27) AMEX. Stephan Company30 tcr
1) Общая лексика: hum. сокр. T Cell Receptor2) Компьютерная техника: The Computer Room, Transmission Confirmation Report3) Спорт: Team Crash Racing4) Военный термин: Tactical Control Room, Time Critical Requirements, Transfer Control Record, Transportation Corps release, technical change request, technical characteristics review, technical compliance record, terrain clearance radar, terrain-closure rate, test condition requirements, traffic control radar5) Техника: tab card reader, target-to clutter ratio, telemetry compression routine, temperature coefficient of reactivity, temperature control reference, temperature-controlled room, thermofor catalytic reforming, time code reader, time constant regulator, transfer control register, two-color radiometer, Термический коэффициент сопротивления (Thermal Coefficient of Resistivity)6) Оптика: temperature coefficient of resistance7) Сокращение: Tracer8) Генетика: ГЕНОМНАЯ ОРГАНИЗАЦИЯ T-КЛЕТОЧНЫХ РЕЦЕПТОРОВ9) Иммунология: T Cell Receptor10) Банковское дело: Transaction Component Records11) Полимеры: technically classified rubber12) Полупроводники: temperature coefficient of resistivity13) Энергосистемы: theoretical capacity remuneration14) Электротехника: thyristor controlled reactor, thyristor controlled rectifier15) Чат: Twentieth Century Romeo16) NYSE. Cornerstone Realty Income Trust I31 tsc
1) Компьютерная техника: Telecom Signaling Card3) Военный термин: TROJAN Switching Center, Tactical Support Company, Top Secret Club, Top Secret Control, Troop Support Command, tactical satellite communications, tactical support center, target selection confusion, technical subcommittee, terminal service company, test steering committee, test support controller, total system control, training support center4) Техника: target signature classification, telephone signaling converter, television scan converter, test set computer, thermally stimulated conductivity, time sharing control task, total soluble cations, totally self-checking system, transportable communications system, twisted smectic c-phase5) Сельское хозяйство: Tractor Sales Corporation6) Религия: Texas Soul Clinic7) Юридический термин: sign a contract8) Бухгалтерия: True Stranded Costs9) Астрономия: Thermally Stimulated Currents10) Металлургия: thin slab caster11) Телекоммуникации: Test System Controller12) Сокращение: Tactical Support Centre, Technical Support Center, Theater Surface Combatant, Total Ship Computer (system), Total Ship Computing, Transport Support Command, Triple Store Carrier, термоструктурные композиты (Thermostructural Composites)13) Университет: Taggart Student Center14) Физиология: Thermal Shock Chamber, Triage Station Controller, Tuberous Sclerosis Complex15) Вычислительная техника: Triton System Component, Triton System Controller, transmitter start code, Time Stamp Counter (Intel), Triton System Controller (Intel, Triton, IC)16) Транспорт: Transportable Storage Canister, Two Stroke Cycle17) Фирменный знак: The Service Center, The Service Company, Tractor Supply Company18) СМИ: The Space Channel19) Деловая лексика: Time Stamp Counter20) Производство: total annual stocking cost21) Полимеры: thermal stress cracking, total solids concentration22) Океанография: Transportation Systems Center23) Расширение файла: Time Sharing Control24) Нефть и газ: ТПК - Технический подкомитет (Technical subcommittee)25) Электротехника: thermally stimulated current, thyristor switched capacitors26) Майкрософт: счётчик метки времени27) AMEX. Stephan Company32 CTP
1) Авиация: component test program2) Медицина: cytidine triphosphate, ЦТФ, цитидинтрифосфат3) Американизм: Call To Power4) Спорт: Closest To The Pin5) Военный термин: Communications Terminal Processor, Component Transition Plan, central transfer point, combat training program, consolidated telecommunications program, coordinated test plan, coordinated test program, общая тактическая обстановка (Common Tactical Picture), ОТО, общая тактическая картина6) Техника: Center for Theoretical Physics, charge transformation parameter, coded telemetry processor, communications timing procedure, connectionless transport protocol, construction test procedure, containment test pressurization, controlled temperature profile7) Математика: Complement Taking Predicate8) Бухгалтерия: Corporate Trade Payment9) Автомобильный термин: closed throttle position10) Биржевой термин: Composite Theoretical Performance11) Сокращение: Centralized Token Passing, Common Tactical Picture, Common Transport Policy, Comparative Test Programme (NATO), Continuum Training Plan, capacity-to-promise12) Театр: Chi Town Players13) Университет: Coach Training Program14) Вычислительная техника: Cordless Telephony Profile (Bluetooth)15) Нефть: cleaning to pits, compressional travel time, очистка со сбросом выбуренной породы в отстойные амбары (cleaning to pits)16) Иммунология: Converged Technologies Professional17) Банковское дело: форма размещения евронот, при которой неразмещённые евроноты забирают участники аукциона (continuous tender panel)18) СМИ: Cartoon Television Program19) Инвестиции: continuous tender panel20) Макаров: computer-to-plate, laser computer-to-plate22) Чат: Congenial Talking Philosophers23) NYSE. C M P Group, Inc.24) НАСА: Critical Technical Parameter25) Программное обеспечение: Click Through Program, Customer Technology Preview26) Хобби: Card Type Possible33 IEC
1) Общая лексика: МЭК (стандарт), Information, Education and Communication2) Компьютерная техника: International Electrotechnical Commitee3) Медицина: Независимый этический комитет (НЭК) (Independent Ethics Committee)4) Американизм: Inland Empire Coalition5) Военный термин: Imagery Exploitation Center, Intelligence Exchange Conference, International Electro-technical commission, integrated environmental control, integrated equipment component, inventory effectiveness control, item entry control, Imagery Exploitation Cell (w/in CARS)6) Техника: integrated electronic control7) Сельское хозяйство: ion exchange capacity8) Телекоммуникации: Interexchange Carrier, International electromagnetic commission9) Сокращение: Inter-Exchange Carrier, Injection Emitter Coupling, Integrated Electronic Component, International Electrotechnical Committee, Information, education and communication - Информация, образование, общение - кампания по профилактике ВИЧ/СПИД., Independent Ethics Committee10) Университет: Interuniversity Expertise Center11) Электроника: Internet Easy Chat12) Вычислительная техника: informational exception control, Inter-Exchange Carrier (AT&T, MCI, LEC), Inter-Exchange Carrier (Telephony, see also, IXC), International Electrotechnical Commission (organization, Schweiz)13) Деловая лексика: Код импортёра-экспортера14) Глоссарий компании Сахалин Энерджи: induction log, Международная электротехническая комиссия (International Electrotechnical Commission)15) Образование: Information Education Communication16) Сетевые технологии: Information Exchange Center17) Полимеры: International Electrochemical Commission18) Автоматика: infused emitter coupling19) Научный термин: Институциональный этический комитет (Institutional Ethics Committee)20) Макаров: International Electrical Commission21) Расширение файла: International Electrotechnical Commission22) Электротехника: международная электротехническая комиссия, МЭК (International Electrotechnical Commission), (International Electric Code) Международный стандарт по электротехнике23) Федеральное бюро расследований: Intelligence Evaluation Committee24) Международные перевозки: Import Export Code34 Group
35 Group
в соч.- European Unix Users Group
- Frankfurt Group
- Government Electronics Group
- Group 1
- Group 2
- Group 3
- Group 4
- High Sierra Group
- Hollywood Digital Video Advisory Group
- Internet Engineering and Planning Group
- Internet Engineering Steering Group
- Joint Photographic Expert Group
- Joint Test Action Group
- Moving Picture Experts Group
- MUMPS User Group
- Object Management Group
- Open Group
- Peripheral Component Interconnect Industrial Computers Manufacturers Group
- Peripheral Component Interconnection Industrial Computers Manufacturers Group
- Post Office Code Standardization Advisory Group
- Rock Ridge Group
- Special Interest Group for CD Applications and Technology
- Special Interest Group for Computer Graphics
- Special Interest Group for Human-Computer Interaction
- Speech Coding Experts Group
- Standards Promotion and Application Group
- Super Post Office Code Standardization Advisory Group
- TEX Users Group
- Universal Asymmetric Digital Subscriber Line Working Group
- Universal Messaging Interoperability GroupThe New English-Russian Dictionary of Radio-electronics > Group
36 GMF
1) Общая лексика: Graphical Modeling Framework (framework within the Eclipse platform. It provides a generative component and runtime infrastructure for developing graphical editors based on the Eclipse Modeling Framework (EMF) and Graphical Editing Framework (GEF)2) Военный термин: Global Military Force, ground mobile forces, guided missile facilities3) Техника: galactic magnetic field4) Сокращение: George MacDonald Fraser (British writer) (http://encyclopedia.thefreedictionary.com/George+MacDonald+Fraser), German Marshall Fund (non-partisan American public policy and grantmaking institution dedicated to promoting greater cooperation and understanding between the United States and Europe.), Ground Mobile Force, got me fucked (сленг. often used by technical students after technical instructors ask a really difficult question, что-то вроде нашего х.з.), Garantie Mutuelle des Fonctionnaires (French), General Mail Facility, General Medical Floor, General Message File, Generalized Mainline Framework, Generalized Matched Filter, Generalized Monitoring Facility, Global Missions Fellowship, Government Materials Furnished, Grand Mother's Funck (Swiss band), Greatly Modulated Frequency, Group-Matched Filter, Groupes de Me'decine de Famille (French; Quebec, Canada), Guided Missile Facility, Gulf of Mexico Foundation, генетически модифицированные продукты питания5) Физиология: Genital Male Function6) Вычислительная техника: Graphics Monitor Facility7) Силикатное производство: Glass Manufacturers Federation8) Окружающая среда: "Зеленый муниципальный фонд", Green Municipal Fund9) Сетевые технологии: графическая программа мониторинга10) Полимеры: para-quinonedioxime11) Автоматика: General Motors Fanuc12) Расширение файла: CGM graphics (APPLAUSE)13) Хобби: Galactic Military Forces37 program
1. nto administer a program — выполнять / осуществлять программу
to apply a program — использовать / применять программу
to approve a program — утверждать / одобрять программу
to carry out a program — выполнять / осуществлять программу
to contribute to a program — способствовать выполнению программы; вносить вклад в программу
to expand / to extend a program — расширять программу
to lay out a program — излагать / намечать программу
to map out a program — намечать / составлять программу
to outline a program — излагать / намечать программу
to profess a program — придерживаться программы; отстаивать программу
to set out a program — излагать / намечать программу
to slash a program — урезать ассигнования на какую-л. программу
to unfreeze one's nuclear program — размораживать свою ядерную программу
- action-oriented programto water down one's program — ослаблять свою программу
- activated program
- ad hoc program
- advanced technical training programs
- aerospace program
- agrarian program
- agrarian reform program
- aid program
- all-embracing program
- alternative program
- ambitious program
- anti-inflation program
- anti-marine pollution programs
- armament program
- assistance program
- atomic energy program
- atoms-for-peace program
- austerity program
- ballot-counting program
- bilateral program
- black programs
- broad program
- broad-ranging program
- budget program
- categorical assistance program
- civil nuclear program
- civil nuclear-power program
- clear-cut program
- coherent program
- component program
- comprehensive program
- compromise program
- concerted program
- concrete program
- consolidated program
- constructive program
- coordinator of a program
- country programs
- crash program
- daily program of sittings
- detailed program
- development program
- diminution in a program
- disarmament program
- disease control programs
- domestic assaults on a program
- dormant program
- draft program
- economic development program
- economic recovery program
- economic reform program
- election program
- energy program
- established program
- European Recovery Program
- execution of a program
- expanded program
- export promotion program
- family planning program
- famine relief program
- feasible program
- feed-back program
- fellowship program
- field programs
- fiscal program
- flight program
- follow-on program
- follow-up program
- food program
- foreign policy program
- general democratic program
- global program
- government program
- halt to the program
- health program
- home-policy program
- housing program
- implementation of a program
- industrial development program
- innovative program
- in-plant training program
- integrated program
- interdisciplinary program of research
- intergovernmental program
- investment promotion program
- job-training program
- joint program
- land reform program
- large-scale program
- live program
- long-range program
- long-term program
- major program
- manned program
- marine program
- massive program
- maximum program
- medium-term programs
- militant program
- military-political program
- military-space programs
- minimum program
- modernization program
- monitoring and evaluating programs
- multilateral aid program
- national program
- nation-wide program
- natural resources development program
- negotiating program
- nondefense program
- non-nuclear defense program
- nuclear program
- nuclear test program
- nuclear-power program
- nuclear-weapons program
- operational program
- optional program
- party program
- Peace Program
- peaceful program
- performance of a program
- phased program
- pilot program
- political program
- population program
- power program
- price support program
- priority program
- privatization program
- production program
- program aimed at smth
- program for economic cooperation
- program for peace and international cooperation
- program has begun its most difficult period
- program has raised objections
- program of action
- program of activities
- program of consolidation
- program of general and complete disarmament
- program of gradual change
- program of measures
- program of militarization
- program of national rebirth
- program of research
- program of revival
- program of work
- promotion program
- public investment program
- public program
- reconstruction program
- recovery program
- reform program
- regional program
- regular program
- rehabilitation program
- research program
- resettlement program
- restructured program
- retraining program
- revised program
- revision of a program
- rural development program
- safeguards program
- safety standards program
- scientific program
- social program
- social welfare program
- sound program
- space exploration program
- space program
- special-purpose program
- Star Wars program
- Strategic Defense Initiative Program
- study program
- systematic assessment of the relevance, adequacy, progress, efficiency, effectiveness and impact of a program
- target program
- technical aid program
- terrorism reward program
- tough program
- training program
- unconstructive program
- under the program
- unemployment insurance program
- UNEP
- United Nations Environment Program
- utopian program
- vast program
- viable program
- war program
- wasteful program
- welfare program
- well-balanced program
- well-planned program
- well-thought-out program
- wide-ranging program
- work program
- world food program
- youth exchange program 2. vсоставлять программу, разрабатывать программу; программировать38 division
отдел; бюро; отделение ( компании) ; сектор; управление; дивизион; дивизия; отсек; (раз)деление; разборкаAdvanced Spacecraft and Technology division — НАСА отдел усовершенствованных космических аппаратов и технологии
Aerospace Research Pilot division — отдел подготовки лётчиков-испытателей воздушно-космических аппаратов и космонавтов (на авиабазе им. Эдвардса ВВС США)
Air Organization and Training division — Бр. управление организации и боевой подготовки (авиации ВМС)
Biotechnology and Human Research division — НАСА отдел биотехники и исследований человеческого организма
Electronic Engineering and Instrumentation Systems division — НАСА отдел электронной техники и приборно-измерительных систем
Experimental Test Pilot division — школа лётчиков-испытателей (на авиабазе им. Эдвардса ВВС США)
Flight-Evaluation and Operations Studies division — НАСА отдел лётной оценки и исследования операций
Instrumentation and Communications division — НАСА отдел приборно-измерительного оборудования и средств связи
Instrumentation and Electronic Systems division — НАСА отдел приборно-измерительного оборудования и электронных систем
Manned Space Sciences division — НАСА отдел научных проблем, связанных с полётом человека в космическом пространстве
Manufacturing Research and Technology division — НАСА отдел производственных исследований и технологии производства
Nuclear Systems and Space Power division — НАСА отдел ядерных систем и источников питания для космических аппаратов
Research and Development Applications division — НАСА отдел применения [внедрения] научно-исследовательских и опытно-конструкторских работ
39 appareillage
аппаратура распределения и управления
Общий термин для коммутационных аппаратов и их комбинации с относящимися к ним устройствами управления, измерения, защиты и регулирования, а также для узлов, в которых такие аппараты и устройства соединяются с соответствующими фидерами, комплектующим оборудованием, оболочками и опорными конструкциями.
МЭК 60050 (441-11-01) [1].
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
switchgear and controlgear
general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEC 62271-1, ed. 1.0 (2007-10)]FR
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu’aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEC 62271-1, ed. 1.0 (2007-10)]Тематики
- аппарат, изделие, устройство...
EN
DE
- Schaltanlagen und/oder Schaltgeräte
FR
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
СП
D. Werkstückaufnahmevorrichtung
E. Machine retaining device
F. Appareillage
Приспособление, применяемое на металлорежущем и (или) деревообрабатывающем станке
Источник: ГОСТ 31.010.01-84: Приспособления станочные. Термины и определения оригинал документа
Франко-русский словарь нормативно-технической терминологии > appareillage
40 ensemble d'appareillage de puissance
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
силовое комплектное устройство распределения и управления
СНКУ
Низковольтное комплектное устройство распределения и управления, применяемое для распределения и управления энергией всех типов нагрузок промышленного, коммерческого и аналогичного назначений, не предназначенное для управления не квалифицированным персоналом.
[ ГОСТ Р МЭК 61439.2-2012]EN
power switchgear and controlgear assembly
PSC-assembly
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
NOTE It is not excluded for a PSC-assembly to be located in an area accessible to ordinary persons.
[IEC 61439-2, ed. 2.0 (2011-08)]FR
ensemble d'appareillage de puissance
ensemble EAP
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
NOTE Il n’est pas exclu d’implanter un ensemble EAP dans une zone accessible aux personnes ordinaires.
[IEC 61439-2, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
FR
Франко-русский словарь нормативно-технической терминологии > ensemble d'appareillage de puissance
СтраницыСм. также в других словарях:
Technical architecture — is one of several architecture domains that form the pillars of an enterprise architecture or solution architecture. It describes the structure and behaviour of the technology infrastructure of an enterprise, solution or system. It covers the… … Wikipedia
Technical illustration — is the use of illustration to visually communicate information of a technical nature. Technical illustrations can be component drawings or diagrams.Today, technical illustration can be broken down into three categories. * For specialized… … Wikipedia
Technical Services Staff — is the United States Central Intelligence Agency component responsible for providing supporting gadgets, disguises, forgeries, secret writings, weapons and assassinations. In the 1950s and early 1960s it also researched, investigated, and… … Wikipedia
Technical drawing — Drafter at work … Wikipedia
Component Object Model — Not to be confused with COM file. Component Object Model (COM) is a binary interface standard for software componentry introduced by Microsoft in 1993. It is used to enable interprocess communication and dynamic object creation in a large range… … Wikipedia
Technical analysis — Financial markets Public market Exchange Securities Bond market Fixed income Corporate bond Government bond Municipal bond … Wikipedia
Component Manager — In Apple Macintosh computer programming, Component Manager was one of many approaches to sharing code that originated on the pre PowerPC Macintosh. It was originally introduced as part of QuickTime, which remained the part of Mac OS that used it… … Wikipedia
Technical support — For technical support in finance, see Support and resistance. AT T Mobility provides technical support for some of its mobile phones through Device Support Centers. Technical support or tech support refers to a range of services by which… … Wikipedia
Component content management system — A component content management system (CCMS) is a content management system that manages content at a granular level (component) rather than at the document level. Each component represents a single topic, concept or asset (e.g., image, table,… … Wikipedia
Technical marketing — The term technical marketing originated at the beginning of the explosion of the commercial Internet. Technical Marketing bridges the gap between engineering and sales. In a sentence it can be condensed to, “the art of bringing together… … Wikipedia
technical documentation — Visual information documentation (with or without sound as an integral documentation component) of an actual event made for purposes of evaluation. Typically, technical documentation contributes to the study of human or mechanical factors,… … Military dictionary
Перевод: со всех языков на русский
с русского на все языки- С русского на:
- Все языки
- Со всех языков на:
- Все языки
- Английский
- Арабский
- Испанский
- Немецкий
- Русский
- Словенский
- Украинский
- Французский