-
21 электрические характеристики НКУ
электрические характеристики НКУ
-
[Интент]Параллельные тексты EN-RU
The Standard IEC 60439-1 identifies the nominal characteristics to be assigned to each assembly, defines the environmental service conditions, establishes the mechanical requirements and gives prescriptions about:
• insulation
• thermal behaviour
• short-circuit withstand strength
• protection against electrical shock
• degree of protection of the enclosure
• installed components, internal separation and connections inside the assembly
• electronic equipment supply circuits.
Information specified under items a) and b) shall be given on the nameplate according to the Standard.
Information from items c) to t), where applicable, shall be given either on the nameplates or in the technical documentation of the manufacturer:
a) manufacturer ’s name or trade mark;
b) type designation or identification number, or any other means of identification making it possible to obtain relevant information from the manufacturer;
c) IEC 60439-1;
d) type of current (and frequency, in the case of a.c.);
e) rated operational voltages;
f) rated insulation voltages (rated impulse withstand voltage, when declared by the manufacturer);
g) rated voltages of auxiliary circuits, if applicable;
h) limits of operation;
j) rated current of each circuit, if applicable;
k) short-circuit withstand strength;
l) degree of protection;
m) measures for protection of persons;
n) service conditions for indoor use, outdoor use or special use, if different from the usual service conditions.
Pollution degree when declared by the manufacturer;
o) types of system earthing (neutral conductor) for which the ASSEMBLY is designed;
p) dimensions given preferably in the order of height, width (or length), depth;
q) weight;
r) form of internal separation;
s) types of electrical connections of functional units;
t) environment 1 or 2.
[ABB]Стандарт МЭК 60439-1 определяет номинальные характеристики НКУ, условия эксплуатации, требования к механической части конструкции, а также следующие параметры:
• изоляция;
• превышение температуры;
• прочность к воздействию тока короткого замыкания;
• защита от поражения электрическим током;
• степень защиты, обеспечиваемая оболочкой;
• комплектующие элементы, внутреннее разделение НКУ ограждениями и перегородками, электрические соединения внутри НКУ;
• требования к цепям питания электронного оборудования.
Информация, относящаяся к пунктам а) и b), должна быть указана на паспортной табличке, соответствующей данному стандарту.
Информация, приведенная в пунктах с) … d), должна быть указана либо на паспортной табличке, либо в технической документации изготовителя:
a) наименование изготовителя или товарный знак;
b) обозначение типа, условного номера или другого знака, позволяющих получить необходимую информацию от изготовителя;
c) МЭК 60439-1;
d) род тока (а для переменно тока и частота.);
e) номинальные рабочие напряжения;
f) номинальное напряжение изоляции (или указываемое изготовителем номинальное импульсное выдерживаемое напряжение);
g) номинальное напряжение вспомогательных цепей, если таковые имеются;
h) предельные отклонения параметров;
j) номинальный ток каждой цепи, если таковые приводят;
k) прочность к воздействию короткого замыкания;
l) степень защиты;
m) меры защиты персонала;
n) нормальные условия эксплуатации при внутренней или наружной установке, а также специальные условия эксплуатации, если они отличаются от нормальных.
Степень загрязнения, если она указывается изготовителем;
o) вид системы заземления (режим нейтрали), который был принят при проектировании НКУ;
p) размеры, приводимые в следующей последовательности: высота, ширина (или длина), глубина;
q) масса;
r) вид внутреннего разделения;
s) типы электрических соединений функциональных блоков;
t) окружающая среда 1 или 2.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
Русско-английский словарь нормативно-технической терминологии > электрические характеристики НКУ
-
22 прочность
1) durability
2) <engin.> endurance
3) fastness
4) permanence
5) safety
6) solidity
7) stability
8) strength
9) toughness
– вибрационная прочность
– испытание на прочность
– конструкционная прочность
– местная прочность
– объемная прочность
– поверхностная прочность
– поперечная прочность
– продольная прочность
– прочность изоляции
– прочность конструкции
– прочность кратковременная
– прочность лица
– прочность на изгиб
– прочность на излом
– прочность на износ
– прочность на истирание
– прочность на ключ
– прочность на кручение
– прочность на пробой
– прочность на раздавливание
– прочность на разрыв
– прочность на раскалывание
– прочность на удар
– прочность покрытия
– прочность связи
– расчет на прочность
– ударная прочность
– усталостная прочность
импульсная прочность изоляции — impulse insulation strength
испытание на длительную прочность — stress-rupture test
прочность в мокром состояния — wet strength
-
23 прочность НКУ к воздействию тока короткого замыкания
прочность НКУ к воздействию тока короткого замыкания
-
[Интент]Параллельные тексты EN-RU
The components shall be assembled according to determined rules which can guarantee short-circuit withstand strength, compliance with the temperature-rise limits, insulation, etc.
[ABB]Компоненты должны быть смонтированы в соответствии с определенными правилами, которые обеспечивают прочность НКУ к воздействию тока короткого замыкания, т. е. способность выдерживать термическое действие тока без повреждений, препятствующих его дальнейшей работе.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
Русско-английский словарь нормативно-технической терминологии > прочность НКУ к воздействию тока короткого замыкания
-
24 электрическая прочность изоляции к импульсному напряжению
Engineering: impulse insulation level, impulse insulation strengthУниверсальный русско-английский словарь > электрическая прочность изоляции к импульсному напряжению
-
25 координация изоляции
- Isolationskoordination, f
координация изоляции
Корреляция изоляционных свойств электроаппарата с ожидаемыми перенапряжениями и с характеристиками устройств для защиты от перенапряжений, с одной стороны, и с предполагаемой микросредой и способами защиты от загрязнения — с другой.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
insulation coordination
selection of the electric strength of equipment in relation to the voltages which can appear on the system for which the equipment is intended, and taking into account the service environment and the characteristics of the available protective devices
Source: 604-03-08 MOD
[IEV number 581-21-04 ]FR
coordination de l’isolement
sélection de la rigidité diélectrique des matériels, en fonction des tensions qui peuvent apparaître dans le réseau auquel ces matériels sont destinés, et compte tenu de l'environnement de service et des caractéristiques des dispositifs de protection disponibles
Source: 604-03-08 MOD
[IEV number 581-21-04 ]EN
DE
- Isolationskoordination, f
FR
- coordination de l’isolement
Русско-немецкий словарь нормативно-технической терминологии > координация изоляции
-
26 дисковая катушечная обмотка
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Русско-английский словарь нормативно-технической терминологии > дисковая катушечная обмотка
-
27 координация изоляции
- coordination de l’isolement
координация изоляции
Корреляция изоляционных свойств электроаппарата с ожидаемыми перенапряжениями и с характеристиками устройств для защиты от перенапряжений, с одной стороны, и с предполагаемой микросредой и способами защиты от загрязнения — с другой.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
insulation coordination
selection of the electric strength of equipment in relation to the voltages which can appear on the system for which the equipment is intended, and taking into account the service environment and the characteristics of the available protective devices
Source: 604-03-08 MOD
[IEV number 581-21-04 ]FR
coordination de l’isolement
sélection de la rigidité diélectrique des matériels, en fonction des tensions qui peuvent apparaître dans le réseau auquel ces matériels sont destinés, et compte tenu de l'environnement de service et des caractéristiques des dispositifs de protection disponibles
Source: 604-03-08 MOD
[IEV number 581-21-04 ]EN
DE
- Isolationskoordination, f
FR
- coordination de l’isolement
Русско-французский словарь нормативно-технической терминологии > координация изоляции
-
28 измеритель
gage, instrument* * *измери́тель м.
meterизмери́тель ви́димости метеор. — visibility meterизмери́тель влагопроница́емости ( бумаги) — water penetration testerизмери́тель воздухопроница́емости ( бумаги) — air permeability testerизмери́тель временны́х интерва́лов — time-interval counterизмери́тель высоты́ (ни́жней грани́цы) облако́в — ceilometerизмери́тель вы́хода ( выходной мощности) — output meterизмери́тель глубины́ отпеча́тка ( твердомера) — imprint depth [indentation depth] indicatorизмери́тель деформа́ции — strain gaugeизмери́тель диа́метра сква́жины — hole calipering [section] gaugeизмери́тель добро́тности — Q-meter, quality-factor meterдо́плеровский измери́тель ( скорости и сноса) ав. — Doppler navigatorизмери́тель ды́рчатости ( бумаги) — hole detectorизмери́тель ё́мкости — capacitance meter, capacitometerизмери́тель жё́сткости — rigidimeterизмери́тель заземле́ния — earth-electrode resistance testerизмери́тель затуха́ния тра́кта — transmission measuring setизмери́тель звуково́го давле́ния — acoustic radiometerизмери́тель зо́льности ( бумаги) — ash meterизмери́тель интенси́вности излуче́ния — radiation rate meterизмери́тель искаже́ний — distortion meterизмери́тель истира́емости — abrasion testerизмери́тель капилля́рной впи́тываемости ( бумаги) — capillarity testerизмери́тель колеба́ний — vibration meterизмери́тель коэффицие́нта детона́ций ак. — wow-and-flutter meterизмери́тель коэффицие́нта мо́щности — power-factor meterизмери́тель коэффицие́нта отраже́ния — reflection [return loss] measuring setизмери́тель коэффицие́нта шумо́в — noise-figure meterизмери́тель лине́йной деформа́ции ( бумаги) — expansion testerизмери́тель магни́тного пото́ка — fluxmeterизмери́тель модуля́ции — modulation meter, modulation monitorизмери́тель мо́щности — power meterизмери́тель мо́щности до́зы радиа́ции — dose-rate meterизмери́тель мо́щности поглоща́ющего ти́па — terminating power meterизмери́тель накло́на бурово́й сква́жины — borehole dipmeterизмери́тель направле́ния ве́тра — wind indicatorизмери́тель напряжё́нности по́ля — field-intensity [field-strength] meterизмери́тель нелине́йных искаже́ний — distortion meter, distortion analyzerизмери́тель неодноро́дности цепи́ — reflection [return loss] measuring setизмери́тель оседа́ния кро́вли горн. — convergence recorderизмери́тель отклоне́ния частоты́ — frequency-deviation meterизмери́тель отрица́тельных ускоре́ний — decelerometerизмери́тель перехо́дных поме́х — cross-talk measuring set, cross-talk meterизмери́тель преломле́ния — refractometerизмери́тель проходя́щей мо́щности — feed-through power meterизмери́тель пыле́ния ( бумаги) — fluff testerизмери́тель радиоакти́вности — radioactivity meterизмери́тель радиопоме́х — radio-noise meterизмери́тель расхо́да (газа, жидкости) — flow (rate) meterизмери́тель расхо́да то́плива — fuel flow meterсамопи́шущий измери́тель у́ровня переда́чи — transmission level recorderизмери́тель си́лы зву́ка — sound level meterизмери́тель си́лы сигна́ла — signal-strength meter, S-meterизмери́тель ско́рости испаре́ния — evaporimeterизмери́тель ско́рости проце́сса — rate meterизмери́тель ско́рости ре́зания — cut meterизмери́тель ско́рости счё́та — count rate meterизмери́тель ско́рости тече́ния — current meterизмери́тель слы́шимости — audibility meterизмери́тель солё́ности морско́й воды́ — salinity meterизмери́тель сопротивле́ния изоля́ции — insulation testerизмери́тель толщины́ строки́ радио — linewidth gaugeизмери́тель угла́ сно́са — drift indicator, drift meterизмери́тель угловы́х ускоре́ний — angular accelerometerизмери́тель укло́на — gradient indicatorизмери́тель у́ровня — level [depth] gaugeизмери́тель у́ровня гро́мкости — volume-unit meterизмери́тель у́ровня жи́дкости — liquidometerизмери́тель у́ровня ма́сла — oil-depth [oilcontent] gaugeизмери́тель ускоре́ния — accelerometerизмери́тель цветово́й температу́ры — colour temperature meterизмери́тель часто́тной характери́стики — frequency-response analyser, frequency-response tracerизмери́тель ширины́ полосы́ прок. — width gaugeизмери́тель ширины́ полосы́, инфракра́сный прок. — infra-red width gaugeизмери́тель ширины́ полосы́, рентге́новский прок. — X-ray width gaugeизмери́тель ширины́ полосы́, электро́нный прок. — electronic width gaugeизмери́тель электри́ческого по́ля ( в атмосфере) — electric field meter* * * -
29 сопротивление
resistance
(величина эл. сопротивления)
сопротивление, которое оказывает электрическая цепь (проводник) движущимся в ней электрическим зарядам, выражается в омах. — а property of conductors which, depending on their dimensions, material, and temperature, determines the current produced by a given difference of potential. the practical unit of resistance is ohm.
- (механическое, как мера прочности) — strength
- (элемент, создающий электрическое сопротивление) — resistor
устройство, включенное в эл. цепь для создания сопротивления протекающему току, сопротивления бывают постоянными и переменными. — а device connected into an electrical circuit to resist the flow of electric current in a circuit. there are two types - fixed and variable.
-, активное (эл.) — resistance
-, аэродинамическое — drag (d)
-, балансировочное — trim drag
-, буксировочное — tawing drag
-, включенное в цепь — resistor connected in circuit
-, волновое — wave drag
-, выносное (эл.) — remote resistor
-, гидравлическое — hydraulic resistance
-, добавочное (омическое) — additional resistance
-, дополнительное лобовое — additional drag
-, емкостное (эл.) — capacitive reactance
opposition offered by capacitors.
- жидкости — resistance of fluid
жидкость поглощает основную часть энергии амортстойки, преодолевая сопротивление жидкости, проходящей no каналам. — fluid absorbs most of impact energy of the shock strut, in overcoming resistance of fluid flowing through passages.
- изоляции — insulation resistance
-, индуктивное (аэродин.) — induced drag
составляющая полного лобового сопротивления крыла, изменяющаяся в зависимости от подъемной силы. — the part of the drag associated with the lift.
-, индуктивное (эл.) — inductive reactance
электрическое сопротивление, обусловленное индукционностью цепи синусоидального тока. — opposition to flow of alterhating or pulsating current by the inductance of a circuit.
-, кажущееся лобовое — apparent drag
- коррозии — resistance to corrosion
-, лобовое — drag (d)
проекция полной аэродинамической силы на направление полета (потока) или составляющая этой силы, направленная против движения самолета. — а retarding force acting upon а body in motion through а fluid (air) parallel to the direction of motion of the body.
-, магнитное — reluctance
отношение магнитодвижущей силы к магнитному потоку. — resistance of а magnetic path to flow of magnetic lines of force.
- материалов — strength of materials
-, нелинейное — nonlinear resistance
-, общее (напр., потенциометpa) — total resistance. ratio of output resistance to total resistance.
-, омическое — ohmic resistance
сопротивление постоянному — resistance to direct current.
-, относительное (отношение активного сопротивления к омическому) — resistance ratio, relative resistаnce
-, относительное, выходное — output resistance ratio
-, переменное — variable resistor
резистор с изменяемым cопротивлением. напр., реостат, потенциометр. — resistor, the resistance of which may be changed. (rheostat and potentiometer)
-, переходное (эл.) — contact resistance
- переходного контакта — contact resistance
- поверхностного трения — surface-friction drag
the part of the drag due to the tangential forces on the surface.
-, подборное (регулируемое) — adjustable resistor
-, полное (эл.) — impedance
полное сопротивление (омическое и реактивное), создаваемое цепью при прохождении переменного тока. измеряется в омах. — the total opposition (i.e. resistance and reactance) a circult offers to a.c. flow. measured in ohms.
-, полное лобовое — total drag
-, постоянное (резистор) — fixed resistor
нерегулируемый резистор, создающий заданную величину сопротивления в электрической цепи. — а resistor designed to introduce only а predetermined amount of resistance into ал electrical circuit and not adjustable.
- при нулевой подъемной силе, лобовое — zero-lift drag
правило площадей применяется при расчетах конструкции для получения минимального сопротивления при нулевой подъемной силе. — area rule is а method of design for obtaining minimum zero-lift drag.
-, профильное — profile drag
the sum of the surface-friction and form drags.
-, развязывающее — decoupling resistor
-, реактивное (эл.) — reactance
opposition to ас flow.
-, регулируемое — adjustable resistor
the resistor which can be adjusted occasionally by the user (by means of a screw).
- с отводом (эл.) — tapped resistor
-, суммарное лобовое — total drag
- трения — surface-friction drag
-, угольное (регулятора напряжений) — carbon pile resistor
- (лобового стекла) удару при столкновении с птицей (прочность) — bird strike resistance (of windscreen)
-, удельное (эл.) — specific resistance
resistance of а conductor expressed in ohms per unit length per unit area.
- формы (аэродинамического профиля, тела) — form drag. pressure drag less induced
-, электрическое — electric resistance
an ohmmeter is an instrument for measuring electric resistance.
включать с. (в эл. цепь) — connect the resistor (in circuit)
оказывать с. (эл.) — offer opposition
capacitive reactance is opposition offered by capacitors.Русско-английский сборник авиационно-технических терминов > сопротивление
-
30 загрязнение (в электробезопасности)
загрязнение
Присутствие инородного вещества: твердого, жидкого или газообразного (ионизированные газы), - которое может вызвать уменьшение диэлектрической прочности или поверхностного сопротивления.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
загрязнение
Любое добавление инородных веществ, твердых, жидких или газообразных (ионизированных газов), которые могли бы уменьшить электрическую прочность изоляции или удельное сопротивление поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
pollution
any condition of foreign matter, solid, liquid or gaseous (ionized gases), that may affect dielectric strength or surface resistivity
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
any addition of foreign matter, solid, liquid or gaseous that can produce a permanent reduction of dielectric strength or surface resistivity of the insulation
NOTE – Ionized gases of a temporary nature are not considered as to be a pollution.
[IEV number 442-01-28]
contamination
the first is defined as area and the second as particulate. The first is caused by surface contaminants that cannot be removed by cleaning or are stained after cleaning. Those may be foreign matter on the surface of, for example a localized area that is smudged, stained, discoloured, mottled, etc., or large areas exhibiting a hazy or cloudy appearance resulting from a film of foreign materials
[IEC 62276, ed. 1.0 (2005-05)]FR
pollution
tout apport de matériau étranger solide, liquide ou gazeux (gaz ionisés) qui peut entraîner une réduction de la rigidité diélectrique ou de la résistivité de la surface
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
tout apport de matériau étranger solide, liquide ou gazeux qui peut entraîner une réduction permanente de la rigidité diélectrique ou de la résistivité de surface de l'isolation
NOTE – Les gaz ionisés de nature fugace ne sont pas considérés comme une pollution.
[IEV number 442-01-28]
Тематики
Обобщающие термины
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > загрязнение (в электробезопасности)
-
31 загрязнение (в электробезопасности)
загрязнение
Присутствие инородного вещества: твердого, жидкого или газообразного (ионизированные газы), - которое может вызвать уменьшение диэлектрической прочности или поверхностного сопротивления.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
загрязнение
Любое добавление инородных веществ, твердых, жидких или газообразных (ионизированных газов), которые могли бы уменьшить электрическую прочность изоляции или удельное сопротивление поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
pollution
any condition of foreign matter, solid, liquid or gaseous (ionized gases), that may affect dielectric strength or surface resistivity
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
any addition of foreign matter, solid, liquid or gaseous that can produce a permanent reduction of dielectric strength or surface resistivity of the insulation
NOTE – Ionized gases of a temporary nature are not considered as to be a pollution.
[IEV number 442-01-28]
contamination
the first is defined as area and the second as particulate. The first is caused by surface contaminants that cannot be removed by cleaning or are stained after cleaning. Those may be foreign matter on the surface of, for example a localized area that is smudged, stained, discoloured, mottled, etc., or large areas exhibiting a hazy or cloudy appearance resulting from a film of foreign materials
[IEC 62276, ed. 1.0 (2005-05)]FR
pollution
tout apport de matériau étranger solide, liquide ou gazeux (gaz ionisés) qui peut entraîner une réduction de la rigidité diélectrique ou de la résistivité de la surface
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
tout apport de matériau étranger solide, liquide ou gazeux qui peut entraîner une réduction permanente de la rigidité diélectrique ou de la résistivité de surface de l'isolation
NOTE – Les gaz ionisés de nature fugace ne sont pas considérés comme une pollution.
[IEV number 442-01-28]
Тематики
Обобщающие термины
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > загрязнение (в электробезопасности)
-
32 "дуговая" неисправность
"дуговая" неисправность
Неисправность, приводящая к возникновению дуги.
[Интент]Параллельные тексты EN-RU
An arc fault occurs when there is a reduction in the dielectric strength of the insulating means (air, in LV switchboards) interposed between two or more conducting elements at different potential.
The arc is generated at the moment when, due to the high ionization of the air, there is a breakdown of the dielectric of the medium and the consequent flow of the current through it.
In an arc fault the highest stresses are of thermal type and proportional to RaI2 owing to the high value taken by the arc resistance Ra; this because the fault current flows in a medium which is always insulating, even if extremely ionized.
Such stresses manifest themselves essentially in the form of:
• high thermal gradients caused by the quick and intense rise in the air temperature;
• high pressure gradients in the form of pressure wave;
• high ionization of the air with consequent reduction of its insulating strength.
Generally speaking, in a LV assembly designed and tested according to the Standard IEC 60439-1 an arc fault is not very likely to occur; however, should it occur, the consequences would be extremely harmful to both the equipment as well as the personnel (see Chapters 2.2 and 2.3).
The causes of an arc fault can be both technical as well as non technical; among the latter the most frequent are the following:
• personnel errors, above all during maintenance operations;
• installation operations not sufficiently accurate;
• inadequate maintenance, above all in the case of severe environmental conditions.
Among the technical causes of an arc fault in a LV assembly the following ones are to be remembered:
• breakdown of the insulation essentially in the proximity of the supports of the busbars and of the plug-in contacts of the withdrawable units (75% of cases);
• overvoltages generating disruptive discharges between the points at minimum clearances (15% of cases);
• constructional defects of the apparatus (10% of cases).
[ABB]К «дуговой» неисправности, относится неисправность, обусловленная уменьшением электрической прочности изолирующей среды (воздуха в НКУ) между двумя или более токоведущими частями, находящимися под разными электрическими потенциалами.
Дуга образуется в тот момент, когда вследствие высокой ионизации воздуха происходит пробой изолирующей среды, вследствие чего через нее начинает протекать электрический ток.
Проявлением дуговой неисправности, является тепловое воздействие, пропорциональное RaI2 и достигающее большого значения вследствие большого сопротивления дуги Ra.
Дело в том, что ток дуги протекает через среду, которая всегда является изолирующей, пусть даже и чрезвычайно ионизированной.
Указанные воздействия очевидны сами по себе особенно в форме:
• теплового градиента температуры, вызванного быстрым и интенсивным подъемом температуры воздуха;
• высоким градиентом давления в форме волны давления;
• высокой ионизацией воздуха с последующим уменьшением электрической прочности.
Вообще говоря, в НКУ, разработанных и испытанных в соответствии с требованиями стандарта МЭК 60439-1 «дуговая» неисправность маловероятна. Однако, если дуга все таки возникнет, ее последствия буду чрезвычайно тяжелыми как для оборудования, так и для персонала (см. п. 2.2 и 2.3).
Причина дуговой неисправности может носить как технический, так и нетехнический характер. Среди последних наиболее часто возникают следующие:
• ошибки персонала, совершаемые главным образом во время технического обслуживания;
• недостаточно аккуратное выполнение монтажа;
• ненадлежащее техническое обслуживание, главным образом при эксплуатации НКУ в тяжелых условиях окружающей среды.
Среди технических причин дуговой неисправности в НКУ необходимо помнить о следующих:
• пробой изоляции, особенно вблизи опор шин и втычных контактов выдвижных частей НКУ (75 % случаев);
• перенапряжения, вызываемые разрушительными электрическими разрядами между точками с минимальными зазорами (15 % случаев);
• конструктивные дефекты аппаратуры (10 % случаев).
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
Русско-английский словарь нормативно-технической терминологии > "дуговая" неисправность
-
33 загрязнение (в электробезопасности)
загрязнение
Присутствие инородного вещества: твердого, жидкого или газообразного (ионизированные газы), - которое может вызвать уменьшение диэлектрической прочности или поверхностного сопротивления.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
загрязнение
Любое добавление инородных веществ, твердых, жидких или газообразных (ионизированных газов), которые могли бы уменьшить электрическую прочность изоляции или удельное сопротивление поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
pollution
any condition of foreign matter, solid, liquid or gaseous (ionized gases), that may affect dielectric strength or surface resistivity
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
any addition of foreign matter, solid, liquid or gaseous that can produce a permanent reduction of dielectric strength or surface resistivity of the insulation
NOTE – Ionized gases of a temporary nature are not considered as to be a pollution.
[IEV number 442-01-28]
contamination
the first is defined as area and the second as particulate. The first is caused by surface contaminants that cannot be removed by cleaning or are stained after cleaning. Those may be foreign matter on the surface of, for example a localized area that is smudged, stained, discoloured, mottled, etc., or large areas exhibiting a hazy or cloudy appearance resulting from a film of foreign materials
[IEC 62276, ed. 1.0 (2005-05)]FR
pollution
tout apport de matériau étranger solide, liquide ou gazeux (gaz ionisés) qui peut entraîner une réduction de la rigidité diélectrique ou de la résistivité de la surface
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
tout apport de matériau étranger solide, liquide ou gazeux qui peut entraîner une réduction permanente de la rigidité diélectrique ou de la résistivité de surface de l'isolation
NOTE – Les gaz ionisés de nature fugace ne sont pas considérés comme une pollution.
[IEV number 442-01-28]
Тематики
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > загрязнение (в электробезопасности)
-
34 импульсная прочность изоляции
Makarov: impulse insulation strengthУниверсальный русско-английский словарь > импульсная прочность изоляции
-
35 поддержание электрической прочности изоляции
Engineering: maintenance of insulation strengthУниверсальный русско-английский словарь > поддержание электрической прочности изоляции
-
36 прочность теплоизоляции
Русско-английский словарь по строительству и новым строительным технологиям > прочность теплоизоляции
-
37 импульсная прочность изоляции
Русско-английский научно-технический словарь Масловского > импульсная прочность изоляции
-
38 измеритель
м. meter -
39 прочность изоляции
Русско-английский глоссарий по космической технике > прочность изоляции
-
40 выравнивание потенциалов
выравнивание потенциалов
Метод снижения напряжения прикосновения и шага между точками электрической цепи, к которым возможно одновременное прикосновение или на которых может одновременно стоять человек
[ ГОСТ 12.1.009-76]
выравнивание потенциала
-
[IEV number 151-15-51]EN
potential grading
reduction of substantial inequalities of electric field strength in or along an insulator or insulation by constructional measures
[IEV number 151-15-51]FR
répartition des potentiels, f
réduction des inégalités importantes du champ électrique à l'intérieur ou à la surface d'un isolateur ou d'une isolation par des moyens incorporés au dispositif
[IEV number 151-15-51]Тематики
EN
DE
FR
- répartition des potentiels, f
Русско-немецкий словарь нормативно-технической терминологии > выравнивание потенциалов
См. также в других словарях:
insulation resistance — izoliacijos atsparumas statusas T sritis fizika atitikmenys: angl. insulating strength; insulation resistance vok. Isolationsfestigkeit, f rus. прочность изоляции, f pranc. rigidité d’isolement, f … Fizikos terminų žodynas
Dielectric strength — In physics, the term dielectric strength has the following meanings: Of an insulating material, the maximum electric field strength that it can withstand intrinsically without breaking down, i.e., without experiencing failure of its insulating… … Wikipedia
Building insulation materials — A selection of insulation materials can aid in building insulation. All of these are based on standard principles of thermal insulation. Materials used to reduce heat transfer by conduction, radiation or convection are employed in varying… … Wikipedia
Thermal insulation — The term thermal insulation can refer to materials used to reduce the rate of heat transfer, or the methods and processes used to reduce heat transfer.Heat energy can be transferred by conduction, convection, radiation or when undergoing a phase… … Wikipedia
Installing building insulation — Due to the variety of building insulation materials available and the various building elements that may require insulation, there are a number of ways of installing building insulation.Where to insulateWhere to insulate depends on where your… … Wikipedia
Exterior insulation finishing system — Exterior insulation and finishing system (EIFS) is a type of building exterior wall cladding system that provides exterior walls with an insulated finished surface and waterproofing in an integrated composite material system. Contents 1… … Wikipedia
Exterior Insulation Finishing System — Exterior Insulation and Finish Systems (EIFS) are a type of building product that provides exterior walls with an insulated finished surface, and waterproofing in an integrated composite material system. Terminology Although often called… … Wikipedia
Multi-layer insulation — Closeup of Multi layer insulation from a satellite. The metal coated plastic layers and the scrim separator are visible. Multi layer insulation, or MLI, is thermal insulation composed of multiple layers of thin sheets often used on spacecraft. It … Wikipedia
Rigid Insulation Board — An insulation product made of a fibrous material or plastic foams, pressed or extruded into board like forms. It provides thermal and acoustical insulation strength with low weight, and coverage with few heat loss paths … Energy terms
dielectric strength — noun : the maximum intensity of electric field that a given dielectric can sustain without disruptive discharge, usually expressed in kilovolts per millimeter * * * Elect. the maximum voltage that can be applied to a given material without… … Useful english dictionary
insulating strength — izoliacijos atsparumas statusas T sritis fizika atitikmenys: angl. insulating strength; insulation resistance vok. Isolationsfestigkeit, f rus. прочность изоляции, f pranc. rigidité d’isolement, f … Fizikos terminų žodynas