Перевод: со всех языков на русский

с русского на все языки

С русского на:
Все языки
Со всех языков на:
Все языки
Английский
Русский

setup+path

Толкование Перевод

1 setup path

Техника: тракт установления соединения

Универсальный англо-русский словарь > setup path
2 setup path

тракт установления соединения

English-Russian dictionary of telecommunications and their abbreviations > setup path
3 path

1) путь

2) канал, тракт

3) цепь

•

- access path
- alternate path
- antenna-feeder path
- audio-frequency path
- baseband transmission path
- best redundant path
- cable path
- capacitive-coupling path
- closed path
- communication path
- conductive path
- conductor path
- control path
- coupling path
- coverage path
- digital radio path
- diver communication path
- electron-beam path
- feedback path
- feeder radio path
- flow transmitting path
- forward interaction path
- forward path
- holding path
- inductive coupling path
- intermediate point-to-intermediate point path
- interphase path
- junction path
- line-of-sight path
- loopless path
- managing station-to-intermediate point path
- network path
- nonlocked path
- optical path
- phone path
- pregroup path
- radiated path
- radio path
- ray path
- receiving path
- return interactive path
- setup path
- shortless loopless path
- signal path
- sneak path
- speech path
- standard path
- submarine cable path
- tape path
- telephone-to-telephone path
- tested path
- transfer path
- transmitting path
- video-frequency path
- voice-frequency path
- voltage path

English-Russian dictionary of telecommunications and their abbreviations > path
4 time

1. время, продолжительность; период; срок || рассчитывать по времени; отмечать время; хронометрировать

2. такт; темп

net time on bottom — время механического бурения

repair and servicing time — время на ремонт и обслуживание

time of running in — время, требуемое на спуск бурового инструмента

wait on plastic time — время ожидания затвердевания пластмассы (при тампонировании скважины полимерами) (до получения прочности, равной 7 МПа)

— arrival time

— average mooring time

— braking time

— closed-in time

— connection time

— delay time

— delta time

— development time

— down time

— drilling time

— equal travel time

— fiducial time

— final setting time

— finite time

— flush time

— full time

— idle time

— in unit time

— infinite closed-in time

— initial setting time

— intercept time

— jelling time

— lost time

— make up time

— mean time

— mooring time

— net drilling time

— operating time

— outage time

— pipe abandoning time

— pipe recovery time

— production time

— pumping time

— reaction time

— readiness time

— reciprocating time

— recovery time

— release time

— removal time

— response time

— rig time

— rig up time

— running time

— set time

— setting time

— setup time

— shot hole time

— shut-in time

— station time

— take time

— tear-down time

— thickening time

— time of advent

— time of arrival

— time of ascend

— time of heat

— time of setting

— time of transit

— time on trips

— transit time

— travel time

— travelling time

— trip time

— unproductive time

— uphole time

* * *

1. время; период; момент; срок; продолжительность

2. наработка

estimated mean time to failure — расчётная средняя наработка до отказа

expected time to first failure — ожидаемая наработка до первого отказа

expected time to repair — ожидаемая наработка до ремонта

mean time between complaints — среднее время между рекламациями; средняя наработка на рекламацию

mean time between defects — средняя наработка между появлениями дефектов

mean time between detectable failures — средняя наработка между обнаруживаемыми отказами

mean time between malfunctions — средняя наработка между отказами

mean time between unscheduled removals — средняя наработка между внеплановыми заменами

mean time of repair — средняя продолжительность ремонта

mean time to crash — средняя наработка до выхода из строя

mean time to diagnosis — среднее время до обнаружения неисправности (после её появления)

mean time to first failure — средняя наработка до первого отказа

mean time to isolate — средняя продолжительность обнаружения (неисправности)

mean time to maintenance — средняя наработка до технического обслуживания

mean time to removal — средняя наработка до замены

mean time to repair failures — среднее время устранения неисправностей

mean time to replacement — средняя наработка до замены

mean time to restore — средняя наработка до ремонта

mean time to return to service — среднее время возвращения в исправное состояние

mean time to unscheduled removal — средняя наработка до внеплановой замены

median time to failure — медиана наработки до отказа

minimum time to repair — минимальная наработка до ремонта

operating time between failures — наработка между отказами

repair time per failure — продолжительность ремонта на один отказ

required time of operation — требуемая наработка

time between maintenance actions — наработка между операциями технического обслуживания

time to first system failure — наработка до первого отказа системы

time to locate a failure — время до обнаружения местонахождения неисправности

time to repair completion — время до завершения ремонта;

time to system failure — наработка до отказа системы

— active maintenance time

— active repair time

— active technician time

— administrative time

— alert time

— attendance time

— available time

— awaiting repair time

— bad time

— corrective maintenance time

— delay technician time

— effective repair time

— engineering time

— equipment repair time

— exponential failure time

— failed time

— failure time

— failure-detection time

— failure-free time

— failure-reaction time

— fault time

— fault-detection time

— fault-free time

— fault-inception time

— final test time

— general repair time

— guarantee time

— in-commission time

— interfailure time

— interrepair time

— localization time

— maintenance time

— makeup time

— malfunction repair time

— mean operating time

— mean repair time

— mean up time

— median maintenance time

— nipple-down time

— nipple-up time

— nonactive maintenance time

— nonfailure operation time

— nonscheduled maintenance time

— operating time

— operational use time

— out-of-commission time

— overhaul time

— preventive maintenance time

— proving time

— pump down time

— readiness time

— ready time

— rejection operating time

— repair delay time

— repair-and-servicing time

— repair-to-repair time

— replacement time

— residual time

— routine maintenance time

— scheduled engineering time

— scheduled operating time

— search time

— service adequacy time

— service time

— standby unattended time

— supplementary maintenance time

— survival time

— switching delay time

— switching time

— technician delay time

— time between defects

— time between failures

— time between overhauls

— time between removals

— time between repairs

— time between replacements

— time between tests

— time since overhaul

— time to damage

— time to failure

— time to repair

— total maintenance time

— total technician time

— troubleshooting time

— turnaround time

— turnover time

— usable time

— wait-before-repair time

— wear-out time

* * *

время; продолжительность; темп; такт

* * *

время, момент

* * *

1) время; период; момент; срок; продолжительность

2) наработка

•

time at shot point — сейсм. вертикальное время;

time between defects — наработка между появлениями дефектов;

time between failures — наработка между отказами;

time between maintenance actions — наработка между операциями технического обслуживания;

time between overhauls — межремонтный срок службы; наработка между капитальными ремонтами;

time between removals — интервал между заменами ( элементов);

time between repairs — межремонтный срок службы; наработка между ремонтами;

time between replacements — интервал между заменами ( элементов);

time between tests — время между испытаниями;

time on bottom — продолжительность нахождения инструмента в забое;

time on trip — время на спуско-подъёмные операции;

time since circulation — интервал времени между остановкой циркуляции бурового раствора и началом каротажа;

time since overhaul — наработка после капитального ремонта;

time to damage — наработка до повреждения;

time to failure — наработка до отказа;

time to first system failure — наработка до первого отказа системы;

time to locate a failure — время до обнаружения местонахождения неисправности;

time to repair — наработка до ремонта;

time to repair completion — время до завершения ремонта;

time to restore — наработка до восстановления;

time to system failure — наработка до отказа системы;

time to the first system failure — наработка до первого отказа системы

- time of advent
- time of arrival
- time of ascend
- time of echo
- time of flight
- time of running-in
- time of service
- time of setting
- time transit
- active maintenance time
- active repair time
- active technician time
- actual casing cutting time
- actual drilling time
- administrative time
- alert time
- arrival time
- attendance time
- available time
- average time between maintenance
- average mooring time
- awaiting repair time
- bad time
- Barnaby time
- bedrock-reflection time
- bit time off-bottom
- bit time on-bottom
- bit run time
- boring time
- break time
- breakdown time
- casing-fluid decay time
- cement setting time
- cementing time
- changing time
- charging-up time
- circulation cycle time
- closed-in time
- composite delay time
- connection time
- coring time
- corrected travel time
- corrective maintenance time
- critical fault clearing time
- critical ray time
- cutting-in time
- datum-corrected time
- dead time
- delay technician time
- discharge time
- down time
- drainage time
- drilling time
- drilling time per bit
- drilling bit changing time
- effective repair time
- elapsed maintenance time
- end-to-end time
- engineering time
- equal travel time
- equipment repair time
- estimated time of repair
- estimated mean time to failure
- estimated repair time
- etching time
- expected time to first failure
- expected time to repair
- expected test time
- exponential failure time
- failed time
- failure time
- failure-detection time
- failure-free time
- failure-reaction time
- fault time
- fault-detection time
- fault-free time
- fault-inception time
- fill-up time
- filling time
- filtration time
- final cement setting time
- final setting time
- final test time
- first-arrival time
- first-break time
- first-event time
- fishing time
- flush time
- forward time
- general repair time
- geological time
- geometrical ray-path time
- geophone time
- ghost travel time
- gross drilling time
- guarantee time
- half-intercept time
- head-wave arrival time
- high-velocity time
- horizon time
- in-commission time
- infinite closed-in time
- infusion time
- initial setting time
- intercept time
- interfailure time
- interpolated time
- interrepair time
- interval time
- interval transit time
- jelling time
- lag time
- least travel time
- localization time
- lost time
- maintenance time
- makeup time
- malfunction repair time
- maximum repair time
- mean time
- mean time between complaints
- mean time between defects
- mean time between detectable failures
- mean time between malfunctions
- mean time between unscheduled removals
- mean time of repair
- mean time to crash
- mean time to diagnosis
- mean time to first failure
- mean time to isolate
- mean time to maintenance
- mean time to removal
- mean time to repair failures
- mean time to replacement
- mean time to restore
- mean time to return to service
- mean time to unscheduled removal
- mean corrective maintenance time
- mean diagnostic time
- mean maintenance time
- mean operating time
- mean repair time
- mean up time
- measured travel time
- median time to failure
- median maintenance time
- minimum time to repair
- mooring time
- moveout time
- moving time
- mud-path correction time
- net time on-bottom
- net drilling time
- nipple-down time
- nipple-up time
- nonactive maintenance time
- nonfailure operation time
- nonproductive rig time
- nonscheduled maintenance time
- normal arrival time
- observed travel time
- off-stream time
- oil field development time
- oil production time
- on-bottom time
- one-way time
- one-way travel time
- operating time
- operating time between failures
- operational use time
- out-of-commission time
- overall time
- overhaul time
- pipe abandoning time
- pipe recovery time
- pool formation time
- pressure build-up time
- pressure readjustment time
- preventive maintenance time
- production time
- productive time
- productive rig time
- propagation time
- proving time
- pulling-out time
- pulse time of arrival
- pumpability time
- pump-down time
- pumping time
- putting on production time
- raw time
- ray-path time
- readiness time
- ready time
- reciprocal time
- reciprocating time
- record time
- reflection arrival time
- reflection travel time
- refraction break time
- refraction travel time
- rejection operating time
- removal time
- repair time per failure
- repair-and-servicing time
- repair-delay time
- repair-to-repair time
- replacement time
- required time of operation
- residual time
- reversed time
- rig time
- rig-down time
- rig-up time
- round-trip time
- round-up time
- routine maintenance time
- running-in time
- sample deformation time
- scheduled engineering time
- scheduled operating time
- search time
- second-event time
- seismic interval time
- seismic record time
- service time
- service adequacy time
- servicing time
- setting time
- setting-up time
- setup time
- shooting time
- shot-hole time
- shot-to-receiver time
- shut-in time
- spending time
- standby time
- standby unattended time
- station time
- step-out time
- supplementary maintenance time
- surface-to-surface time
- survival time
- tank emptying time
- tear-down time
- technician delay time
- thickening time of cement
- total time on test
- total gaging time
- total maintenance time
- total path time
- total rig time
- total technician time
- transit time
- traveling time
- trip time
- troubleshooting time
- turnaround time
- turnover time
- two-way travel time
- unproductive time
- uphole time
- uphole-shooting time
- usable time
- vertical path time
- vertical travel time
- vibration time
- wait-before-repair time
- waiting-on-cement time
- waiting-on-plastic time
- water-break time
- wave arrival time
- wave transit time
- wave traveling time
- wavefront time
- wear-out time
- weathering time
- well building time
- well drilling time
- well shut-in time
- zero-offset arrival time
- zero-offset travel time
- zero-spread time
* * *

• время пребывания

• время удержания

• момент

Англо-русский словарь нефтегазовой промышленности > time
5 mode

1) вид; тип; характер

2) мода, вид [форма, тип\] колебаний; вид [тип\] волн

3) способ; метод; принцип

4) режим ( работы)

5) вчт. состояние

6) швейн. мода

•

-
ablative pit-forming mode
-
abnormal mode
-
acceleration mode
-
access mode
-
accumulation mode
-
acoustic mode
-
acquisition mode
-
active mode
-
adaptive control mode
-
addressing mode
-
air-liquefaction mode
-
alternate mode
-
anticipation mode
-
approach mode
-
assemble mode
-
astable vibration mode
-
astable mode
-
automatic mode
-
automatic opening mode
-
automatic skinning mode
-
autopilot heading mode
-
autoposition mode
-
avalanche mode
-
axial mode
-
background mode
-
backward mode
-
backward propagating mode
-
backward scattering mode
-
backward scatter mode
-
backward traveling mode
-
bare resonator mode
-
basic mode
-
batch mode
-
birefringent mode
-
block mode
-
block-multiplex mode
-
bound modes
-
broadcast mode
-
buckling mode
-
burst mode
-
calibration mode
-
capture mode
-
cavity flipping mode
-
cavity mode
-
central mode
-
character generation mode
-
character mode
-
characteristic mode
-
charge-coupling mode
-
circularly polarized mode
-
cladding mode
-
clockwise polarized mode
-
coherently locked modes
-
cold mode
-
collective modes
-
command mode
-
common failure mode
-
common mode
-
compatibility mode
-
competing modes
-
compute mode
-
confined mode
-
constant cutting speed mode
-
constant speed mode
-
contention mode
-
continuous mode
-
continuous path mode
-
continuous-wave mode
-
contour modes
-
contradirectional modes
-
control mode
-
conversational mode
-
cooling mode
-
co-orbital mode
-
coplanar mode
-
core-guided mode
-
core mode
-
counterclockwise polarized mode
-
counterrotating circularly polarized modes
-
counting mode
-
coupled modes
-
cross polarized modes
-
cubic mode
-
current mode
-
current saving mode
-
cutoff mode
-
cutting mode
-
damped mode
-
data-processing mode
-
Debye-like mode
-
Debye mode
-
deceleration mode
-
deflected mode
-
degenerated mode
-
degenerate mode
-
depletion mode
-
design mode
-
dialog mode
-
difference mode
-
differential mode
-
diffraction-limited mode
-
diffusive mode
-
discrete mode
-
dispersion modes
-
display mode
-
distributed-feedback mode
-
DNC mode
-
dominant mode
-
double-pass mode
-
drift mode
-
dual-processing mode
-
duplex mode
-
dynamic mode
-
dynamic-scattering mode
-
E mode
-
edge mode
-
edit mode
-
eigen mode
-
electromagnetic mode
-
elementary mode
-
Emn mode
-
emulation mode
-
energy dissipating mode
-
enhancement mode
-
equal-loss modes
-
equally spaced modes
-
erase mode
-
evanescent mode
-
even mode
-
excited mode
-
exciting mode
-
executive mode
-
extensional mode
-
extraordinary mode
-
Fabry-Perot mode
-
face shear modes
-
fast mode
-
faulted mode
-
fiber mode
-
filamentary mode
-
first mode
-
flexural mode
-
forced mode
-
force mode
-
foreground mode
-
foreground-background mode
-
forward mode
-
forward propagating mode
-
forward scattering mode
-
forward scatter mode
-
forward shear mode
-
forward traveling mode
-
fracture mode
-
free-running mode
-
free-space mode
-
frequency-division multiplex mode
-
frequency-shift-keying mode
-
full program mode
-
full-duplex mode
-
fundamental mode
-
gated mode
-
gate mode
-
Gaussian mode
-
generator mode
-
go-ahead mode
-
graphics mode
-
graphic mode
-
guidance mode
-
guided-wave mode
-
guided mode
-
half-duplex mode
-
heating mode
-
height-lock mode
-
higher-order mode
-
high-frequency mode
-
high-loss mode
-
high-pass mode
-
high-resolution mode
-
Hmn mode
-
horizontally polarized mode
-
idler mode
-
independent mode
-
index mode
-
injected mode
-
injection-locked mode
-
in-phase modes
-
in-plane mode
-
insert mode
-
integer mode
-
interacting modes
-
interactive mode
-
internally trapped mode
-
interpretive mode
-
interrupt mode
-
inverter mode
-
isolated mode
-
jog mode
-
kernel mode
-
keyboard mode
-
laser mode
-
lasing mode
-
lattice mode
-
launched mode
-
leaking mode
-
leaky mode
-
left-hand polarized mode
-
left polarized mode
-
length extentional mode
-
length flexural mode
-
length modes
-
length-width flexural mode
-
light mode
-
linearly polarized mode
-
load mode
-
local mode
-
locate mode
-
lock mode
-
long coherence length mode
-
long wavelength mode
-
longitudinal mode
-
loopback mode
-
low-frequency mode
-
low-pass mode
-
low-resolution mode
-
lugdown mode
-
macro-by-macro mode
-
magnetron mode
-
main mode
-
malfunction mode
-
manual mode
-
manual skinning mode
-
mapping mode
-
maser mode
-
master mode
-
matched mode
-
measurement mode
-
message mode
-
mirror image mode
-
mixed mode
-
mode of behavior
-
mode of deformation
-
mode of excitation
-
mode of failure
-
mode of functioning
-
mode of propagation
-
mode of test
-
mode of transport
-
mode-locked mode
-
mode-match mode
-
monopulse mode
-
move mode
-
multiple-frame mode
-
multiplexed mode
-
multiplex mode
-
multitask mode
-
native mode
-
natural mode
-
nonaxial mode
-
noncounting mode
-
nondegenerate mode
-
nondegenerative mode
-
nonoscillating mode
-
nonpropagating mode
-
nonradiative mode
-
nonresonant mode
-
nonspiking mode
-
nontransparent mode
-
normal mode
-
odd mode
-
off mode
-
off-axis mode
-
off-design mode
-
off-line mode
-
off-normal mode
-
on-line mode
-
on-link mode
-
opening fracture mode
-
opening mode
-
operating mode
-
optical mode
-
ordinary mode
-
original mode
-
orthogonally polarized modes
-
oscillating mode
-
oscillation mode
-
oscillatory mode
-
out-of-plane mode
-
overtype mode
-
parallel mode
-
parametric mode
-
parasitic mode
-
partially suppressed mode
-
path following mode
-
path modifying mode
-
penetration mode
-
periodic mode
-
perturbed mode
-
photographing mode
-
photon-counting mode
-
pipelined mode
-
plane mode
-
plane polarized mode
-
plasma mode
-
plasma-guide mode
-
playback mode
-
point-to-point path mode
-
polarization mode
-
polarization-bistable mode
-
polarized mode
-
posttrigger mode
-
power-down mode
-
p-polarized mode
-
pretrigger mode
-
principal mode
-
priviledged mode
-
propagating mode
-
propagation mode
-
pulse counting mode
-
pulsed mode
-
pump mode
-
push-pull mode
-
Q-spoiled mode
-
Q-switched mode
-
quadrupole mode
-
quantum noise limited mode
-
radial mode
-
radially polarized mode
-
radiating mode
-
radiation mode
-
rail mode
-
ranging mode
-
ready mode
-
real-time mode
-
receive mode
-
record mode
-
rectifier mode
-
reflected mode
-
reflection mode
-
reflective mode
-
refracted mode
-
refrigeration mode
-
repetitive Q-switched mode
-
request mode
-
resonant mode
-
resonator mode
-
retropropulsion mode
-
return beam mode
-
reverse bias mode
-
reversible recording mode
-
right-hand polarized mode
-
right polarized mode
-
run mode
-
sample-and-hold mode
-
satellite mode
-
saturation mode
-
scanning mode
-
scan mode
-
scope mode
-
screen mode
-
search mode
-
selected mode
-
selector mode
-
self-ammoniation mode
-
self-heating mode
-
self-locked mode
-
self-Q-switched mode
-
self-refresh mode
-
self-reporting mode
-
self-trapping mode
-
serial mode
-
series mode
-
setup mode
-
severe wear mode
-
shear mode of crack initiation
-
shear mode
-
side mode
-
signal mode
-
simplex mode
-
simulation mode
-
single block mode
-
single mode
-
single Q-switched mode
-
single-channel mode
-
single-character mode
-
single-pulse mode
-
single-step mode
-
slave mode
-
slightly coupled modes
-
spatial mode
-
spectral mode
-
spiking mode
-
split-screen mode
-
s-polarized mode
-
spurious mode
-
spurious pulse mode
-
square mode
-
stable mode
-
standby mode
-
standing-wave mode
-
start-stop mode
-
static mode
-
stationary mode
-
steady state mode
-
stiffened mode
-
still-frame mode
-
storage mode
-
store-and-forward mode
-
stretching mode
-
stripped cladding modes
-
strong mode
-
strongly excited mode
-
substrate mode
-
superradiant mode
-
supervisor mode
-
switching mode
-
symmetric modes
-
synchronously pumped mode
-
tape auto mode
-
teaching mode
-
tearing mode
-
thickness-extensional modes
-
time compression mode
-
time mode
-
time-difference mode
-
time-shared mode
-
torsional modes
-
track-and-hold mode
-
tracking mode
-
transcribe mode
-
transfer mode
-
transformed mode
-
transient mode
-
transit mode
-
transit-time mode
-
transmission mode
-
transparent mode
-
transverse mode
-
TRAPATT mode
-
trapped mode
-
trapped plasma avalanche transit time mode
-
traveling-wave mode
-
triggering mode
-
trimming mode
-
truncated mode
-
tuning mode
-
tunneling mode
-
twist mode
-
two-level mode
-
unattended mode
-
uncoupled modes
-
undamped mode
-
unmanned mode
-
unperturbed mode
-
unstable mode
-
unstiffened mode
-
vertically polarized mode
-
vibration mode
-
vibration-free mode
-
virtual mode
-
voting mode
-
waiting mode
-
walk-off mode
-
warped mode
-
wave mode
-
wavefront watched modes
-
waveguide mode
-
wavy slip mode
-
wear mode
-
whispering modes
-
whistler mode
-
width modes
-
write mode
-
zero-order mode

Англо-русский словарь технических терминов > mode
6 mode

1) способ; метод; режим ( работы), мода

2) форма; тип; вид

3) форма колебаний, вид колебаний

4) состояние

5) наиболее вероятное значение

•

in an interactive mode — совместно с основными работами

in bar mode — при подаче прутка через отверстие в шпинделе ( токарного станка)

in one transfer mode — за один цикл передачи ( данных);

in rotary mode — при вращении

in shaft mode — при установке детали в центрах, при установке обрабатываемой детали в центрах (напр. токарного станка)

in the ready mode — в состоянии готовности

in traverse mode — при линейном перемещении

- 2D mode
- 3D mode
- acceleration mode
- accept/reject mode
- adapt mode
- adaptive control mode
- anticipation mode
- approach mode
- automatic mode of operation
- automatic mode
- automatic skinning mode
- autoposition mode
- batch mode
- closed loop position mode
- CNC mode
- command mode
- compliant mode
- constant cutting speed mode
- constant speed mode
- continuous machine control mode
- continuous mode
- continuous path mode
- contouring mode
- control mode
- conversational mode
- creep mode
- cruise mode
- cubic mode
- dash mode
- deceleration mode
- decentralized mode
- dialog mode
- DNC communication mode
- DNC mode
- dual-range cutting speed mode
- dwell mode
- eigen mode
- emulation mode
- extreme mode
- failsafe mode
- failure mode
- feed-through mode
- flexural nth mode
- full program mode
- hierarchical mode
- horizontal mode
- idle mode
- interactive graphics mode
- interactive mode
- interrupt mode
- iteration mode
- jog mode
- joystick mode
- learn mode
- machining mode
- manual data input mode of operation
- manual mode of operation
- manual skinning mode
- minimally manned mode
- mirror image mode
- mode of inspection
- mode of operation
- mode of servicing
- mode of test
- mode of vibration
- natural mode
- NC mode
- off-line mode
- one-off mode
- one-step drilling mode
- open loop mode
- operating mode
- operation mode
- part manual mode
- pass-through mode
- peck-feed mode
- playback mode
- point-to-point path mode
- ptp path mode
- pulsed mode of laser
- pulsed mode
- question-and-answer mode
- rapid traverse mode
- read-in mode
- replay mode
- retract mode
- rotary mode
- rotation mode
- run mode
- sets-of-parts mode
- setup mode
- single block mode of operation
- single block mode
- single-cycle mode
- skip mode
- skip-feed drill mode
- snap mode
- solving mode
- square mode
- standalone mode
- step-feed drilling mode
- system mode
- tape auto mode
- tape mode
- teach mode
- teaching mode
- track/touch mode
- tracking mode
- translation mode
- translucent mode
- traverse mode
- unattended mode
- unmanned mode
- variable speed mode
- vertical mode
- vibration mode
- vibrational mode
- vibration-free mode
- virtual call mode
- zoom mode

English-Russian dictionary of mechanical engineering and automation > mode
7 data

( pl от datum)

1) данные; информация; сведения

2) характеристики; параметры; координаты

3) измеренные величины; показания приборов

•

data above voice — данные, передаваемые на частотах выше речевого диапазона

data under voice — данные, передаваемые на частотах ниже речевого диапазона

- 2D scan data
- 2D-design data
- 3D scan data
- 3D-design data
- AC data
- adaptive data
- administrative data
- alphameric data
- alphameric machine-readable data
- alphanumeric data
- alphanumeric machine-readable data
- analog data
- assembly data
- attribute data
- attributes data
- audit data
- axis data
- behavioral data
- blank shape data
- brazing data
- CAD data
- CAD-generated data
- CAD-geometry data
- capability data
- C-L data
- CNC data
- command data
- computerized design data
- continuous data
- coordinate scan data
- correct data
- corrected profile data
- correction data
- correction offset data
- correlating data
- corrupted data
- curve data
- curve positional data
- curved surface data
- customer due data
- cutting data
- cutting tool data
- design data
- detecting data
- digital coded data
- digital data
- digital profile data
- digital program data
- dimensional component data
- dimensions data
- directory data
- discrete data
- DNC program data
- editing data
- electronic data
- entering program data
- equipment condition data
- explicit data
- failure analysis data
- failure data
- free-form data
- fused data
- gage data
- general management data
- graphical presentation data
- hard data
- historical data
- hyperbolic positional data
- image data
- implicit data
- inch-metric input data
- incoming sensory data
- initial data
- input data
- input shape data
- instruction data
- itemized data
- job-tracking data
- line-edited input data
- live data
- machine data
- machine setup data
- machine tool data
- machine-code data
- machining result data
- manufacturing data
- master data
- math data
- model data
- motion data
- multidigit data
- NC coded data
- NC data
- NC run data
- NC running data
- noisy data
- nonvolatile data
- observation data
- observational data
- observed data
- offset curve data
- offset data
- operating data
- operational control data
- operator-entered data
- ordering data
- output data
- part-programming data
- path data
- pattern data
- PC's data
- phase-modulated data
- point data
- position data
- positional data
- positional demand data
- predicted data
- presetting data
- probe data
- product tooling data
- quality-control data
- raw data
- real-time tool data
- reference data
- resources master data
- run data
- running data
- sampled data
- scan data
- sensor signal data
- sensory data
- service data
- setup weld data
- shared data
- slice data
- soldering data
- source data
- specified data
- spindle nose data
- static tooling data
- statistical data
- stored data
- structured tool data
- supplier data
- survey data
- synthetic data
- taped data
- tape-input data
- teaching data
- technology data
- test data
- testing data
- three-dimensional data
- timing data
- tool condition data
- tool location data
- tool master data
- torque data
- training data
- transient response data
- unprocessed position data
- video data
- vision data
- wireframe data
- work data
- workcycle data
- workpiece shape data

English-Russian dictionary of mechanical engineering and automation > data
8 machining

обработка, механическая обработка, механообработка, обработка резанием, обработка на металлорежущем станке

machining all surfaces at a set — обработка всех поверхностей ( заготовки) с одного установа

machining for stock — обработка деталей складского резерва

machining from solid — обработка ( детали) из целого, обработка ( детали) из целого куска

machining from the solid — обработка ( детали) из целого, обработка ( детали) из целого куска

in machining — в обработке, при обработке

machining on all faces — обработка всех поверхностей ( заготовки)

machining through all angles — обработка под любым углом, обработка изделий под любым углом

machining to close limits — обработка с жёсткими допусками; точная обработка

- 2 1/2 D machining
- 2 1/2-dimensional machining
- 3D cavity machining
- 3D machining
- abrasive belt machining
- abrasive flow machining
- abrasive machining
- abrasive-electrochemical machining
- abrasive-waterjet machining
- adaptive controlled machining
- adaptive machining
- all-over machining
- angular machining
- anode-mechanical machining
- around-the-part machining
- associative machining
- automated machining
- automotive machining
- back end machining
- back-face machining
- balanced machining
- batch machining
- batch-lot machining
- beam machining
- bore machining
- CAM machining
- C-axis machining
- center machining
- chemical machining
- chip-type machining
- close tolerance machining
- closed loop machining
- CNC horizontal machining
- CNC machining
- CNC screw machining
- composite machining
- computer-controlled machining
- consistent machining
- constant power machining
- contact-initiated discharge machining
- contact-initiated machining
- continuous path machining
- contour machining
- contouring machining
- controlled machining
- conventional machining
- copy machining
- datum machining
- deephole machining
- diamond machining
- dual-spindle machining
- duplex machining
- duplicate machining
- edge machining
- electrical discharge machining
- electrical machining
- electrical spark machining
- electrochemical machining
- electroerosion abrasive machining
- electroerosion machining
- electrolytic abrasive machining
- electrolytic machining
- electron beam machining
- electron discharge machining
- electronic erosion machining
- electrophysical machining
- electrospark machining
- etch machining
- false machining
- fast laser machining
- feature-based machining
- final machining
- final tolerance machining
- finish machining
- finished machining
- five-axis CNC machining
- five-axis machining
- five-face machining
- five-sided machining
- fixed-axis machining
- flat abrasive machining
- flexible machining
- flow-line machining
- flowthru machining
- flush fine machining
- form-feature machining
- front-end machining
- gear machining
- generative machining
- group machining
- hard-part machining
- heavy machining
- heavy-duty machining
- high-accuracy machining
- high-definition finish machining
- high-efficiency machining
- high-production machining
- high-speed machining
- high-volume machining
- horizontal machining
- horizontal mode machining
- hot machining
- hydrodynamic machining
- inclined-plane machining
- in-cycle machining
- industrial laser machining
- in-place machining
- interference-free machining
- intol/outtol machining
- ion beam machining
- jet-assisted machining
- job shop machining
- laser machining
- laser-assisted machining
- laser-beam machining
- lathe machining
- LH machining
- light-duty machining
- lights-out machining
- magnetic abrasive machining
- manual machining
- medium-duty machining
- minimum-manned machining
- mirror image machining
- multiaccess machining
- multiaxis machining
- multicell machining
- multiface machining
- multilateral machining
- multimachine machining
- multiple machining
- multiple setup machining
- multiple surface flow-line machining
- multiple-axis machining
- multiple-cutter machining
- multiple-electrode electrical discharge machining
- multiple-pass machining
- multiple-source laser machining
- multiple-workpiece machining
- multiplunge machining
- multipurpose machining
- multistage machining
- NC machining
- NF machining
- no-handwork machining
- nonturning machining
- numerical control machining
- numerically controlled machining
- off-center machining
- one-hit machining
- one-operation machining
- one-pass machining
- one-stop machining and grinding
- on-line machining
- parabolic machining
- parallel machining
- partially manned machining
- photochemical machining
- photon beam machining
- photonic machining
- pick feed traverse machining
- plasma-arc machining
- plasma-assisted machining
- plunge machining
- point-to-point machining
- post-process machining
- precision machining
- primary machining
- prismatic machining
- radial machining
- random flexible machining
- rapid machining
- rear-end machining
- RH machining
- rotary machining
- rotary transfer machining
- rotational machining
- rough machining
- roughing machining
- screw machining
- sculpture machining
- sculptured-surface machining
- secondary machining
- semifinish machining
- semi-fourth axis machining
- semiunmanned machining
- series machining
- side machining
- simultaneous fourth-axis machining
- single setup machining
- single-cutter machining
- single-pass machining
- single-point machining
- six-face machining
- six-sided machining
- slideway machining
- solids-based machining
- spark discharge machining
- spark erosion machining
- standalone machining
- straight production machining
- strip machining
- surface intersection machining
- Swiss machining
- Swiss-style machining
- tandem machining
- tapeless machining
- tapered machining
- templet-controlled machining
- test machining
- thermochemical machining
- three-axis curve machining
- three-axis machining
- three-dimensional machining
- tombstone machining
- toolroom machining
- torque-controlled machining
- total machining
- tracer machining
- transfer machining
- transfer-line machining
- trial machining
- turned part machining
- turning machining
- two-and-half axis machining
- two-at-a-time machining
- two-pass machining
- ultrafast machining
- ultrahigh speed machining
- ultrasonic abrasive machining
- ultrasonic machining
- ultrasonically assisted machining
- unattended machining
- unattended multiple-workpiece machining
- unmanned machining overnight
- unmanned machining
- unstable machining
- untended machining
- vertical machining
- vertical mode machining
- vibroabrasive machining
- waterjet machining
- waterjet-assisted machining
- wire electric discharge machining
- wire erosion machining
- wire machining

English-Russian dictionary of mechanical engineering and automation > machining
9 position

1) позиция; место; положение; местоположение; расположение || располагать; размещать; устанавливать в заданное положение; позиционировать; определять [фиксировать\] местоположение

2) координата || устанавливать на заданную координату

3) разряд ( числа); место цифры

•

to anchor in position — зафиксировать в позиции (напр. деталь на столе)

position up — рабочее состояние позиции

-
fuel-on position
-
full-on position
-
hold-in position
-
active position
-
actual position
-
actuating position
-
aircraft alert position
-
at-rest position
-
attitude position
-
beacon position
-
beginning position
-
bit position
-
blade float position
-
blade lower position
-
blade raise position
-
blade tilt position
-
blowing position
-
bottle-up position
-
braking position
-
carousel positions
-
center valve position
-
character position
-
charging position
-
code position
-
collapsed position
-
commanded drive position
-
commentator's position
-
computed grasp position
-
contact alignment position
-
continuous-path position
-
coordinate position
-
cursor home position
-
danger position
-
datum position
-
dead-center position
-
decimal position
-
design position
-
die position
-
digging position
-
digit position
-
docked position
-
drilling position
-
end position
-
extreme position
-
eye position
-
feed position
-
field transit position
-
final position
-
first position
-
flap approach position
-
flap en-route position
-
flap landing position
-
fouling position
-
grasping position
-
grinding position
-
grind position
-
half engine speed position
-
high-order position
-
home position
-
horizontal position
-
in-between position
-
initial position
-
initial setup position
-
inoperative position
-
instantaneous position
-
intermediate position
-
isolated position
-
jaw-loading position
-
knit selection position
-
level position
-
load/unload position
-
low-order position
-
manual-off position
-
manual-on position
-
miss selection position
-
neutral position
-
nominal position
-
nonknit position
-
nonoperating position
-
nonraised position
-
normal valve position
-
ocean transit position
-
off position
-
offset valve position
-
open flow valve position
-
open position
-
operating position
-
optimum feed position
-
overflew position
-
over-the-road position
-
parked position
-
park position
-
pick-out position
-
pick-up position
-
point position
-
position of extremum
-
position of game
-
prearranged position
-
prepulse position
-
programmed approach position
-
punching position
-
quench position
-
ready position
-
ready-to-work position
-
reference position
-
refining position
-
release position
-
reoriented position
-
rest position
-
retarder position
-
retracted position
-
reverse position
-
ring stable position
-
robot's position
-
rotational position
-
run-in position
-
running position
-
runout position
-
sate position
-
semisubmerged position
-
sign position
-
significant position
-
sit-on-bottom position
-
spinning position
-
standard position
-
starting position
-
start position
-
stationary position
-
storage position
-
stowed position
-
subreference position
-
tachograph second man position
-
takeoff position
-
tapping position
-
target position
-
taxi-holding position
-
tool releasing position
-
tool-change position
-
tool-gripping position
-
tool's position
-
tool-tip position
-
transfer selection position
-
tuck selection position
-
undocked position
-
unknown position
-
unlock position
-
vertical position
-
welt selection position
-
workpiece feed position
-
zero position

Англо-русский словарь технических терминов > position
10 error

1) ошибка; погрешность; отклонение

2) рассогласование; расхождение

•

error in parallelism — отклонение от параллельности

error in percent — относительная погрешность; отклонение в процентах

to recover from an error — восстанавливать работоспособность после отказа или сбоя

- Abbe error
- absolute error
- absolute input error
- absolute output error
- acceptable error
- accidental error
- accumulated error
- accumulative pitch error
- additional error
- adjacent pitch error
- admissible error
- alignment error
- allowable error
- appreciable error
- assembly error
- backlash error
- base pitch error
- basic error
- bias error
- calibration error
- center distance error in machining
- center distance error
- centering error
- chucking error
- combined error
- complementary error
- component error
- composite error of a worm gear
- composite error
- computer error
- concentricity error
- confidence error
- conjugate error
- connection error
- conscious error
- consistent error
- constant error
- contour error
- control error
- conventional error
- coupling error
- cumulative base pitch error
- cumulative error of contact line
- cumulative error
- cumulative gear meshing error
- cumulative pitch error of k pitches of a worm
- cumulative pitch error of k pitches of the rack
- cumulative pitch error
- cyclic error of a gear
- cyclic error
- cylindricity error
- data reduction error
- datum error
- dead-path error
- display error
- dividing error
- dynamic error
- error of a measuring instrument
- error of approximation
- error of division
- error of function
- error of locating
- error of measurement
- error of method
- error of total length
- experimental error
- extreme error
- fatigue-related error
- flatness error
- following error
- form error
- frictional error
- gearing error
- geometrical error
- gimbal error
- gross error
- helical surface error
- human error
- inclination error
- inconsistent error
- independent error
- indexing error
- indication error
- individual error
- initial error
- input error
- instantaneous error
- instrument error
- instrumental error
- intrinsic error
- limiting error
- linear error
- linear meshing error
- load screw error
- loading error
- long-wave error
- long-wave measuring error
- machine zero position error
- manufacturing error
- maximum composite error
- maximum error
- maximum out-off-position error in the teeth
- maximum permissible error
- mean error
- mean probable error
- meshing error
- method error
- mismatch error
- mispositioning error
- monitor error
- motion related error
- mounting distance error
- mounting error
- multiple error
- noncyclic error
- nonlinear error
- nonperpendicular error
- normal adjacent pitch error
- normal individual base pitch error
- normal tooth thickness error
- observation error
- observational error
- one-to-one error
- output error
- overcutting error
- overloading error
- overspeed error
- overwriting error
- parallax error
- parallelism error
- parasitic error
- partial error
- parts-to-platen error
- peak error
- peak negative error
- peak positive error
- phase error
- pitch error
- platen-to-machine error
- positional error
- position-following error
- positioning error
- prediction-following error
- probable error
- profile error
- program data error
- program error
- programming error
- progressive error
- quadrant error
- radial composite error
- random error
- reader error
- reconstruction error
- reduced error
- reducial error
- reference mean error
- reference-limiting error
- relative error
- relative input error
- relative output error
- relocation error
- repeatable error
- residual error
- response error
- response time error
- resultant error
- retroflectors rotational error
- reversal error
- right-angle error
- rotational error
- rounding error
- roundoff error
- running-in error
- sampling error
- scale error
- screw-sizing error
- semantic error
- separation error
- servo error
- servo excess error
- servo following error
- setting error
- setup error
- shaft angle error
- sharpening plane error
- short-wave error
- short-wave measuring error
- single error
- sizing error
- slide position error
- sliding error
- slip-stick-type error
- spacing error
- static error
- statistical error
- steady-state error
- storage error
- stored error
- straigthness error
- substitution error
- successive error of division
- syntactic error
- syntactical error
- system error
- systematic error
- tangential composite error
- tangential tooth-to-tooth composite error
- thermal growth error
- thermally induced errors
- threshold error
- tolerated error
- tool-setting error
- tooth profile error
- tooth-meshing error
- tooth-spacing error
- tooth-to-tooth composite error single flank
- total alignment error of tooth
- total composite error single flank
- total composite error
- total cumulative pitch error
- total error of distortion
- total error
- total instrument error
- total measuring device error
- total profile error
- tracking error
- transient error
- transmission error
- true error
- trueness error
- truncation error
- tuning error
- turning error
- twist errors
- velocity error
- velocity transmission error
- working error
- zero error
- zero following error

English-Russian dictionary of mechanical engineering and automation > error
11 information

информация; данные

to downline information — передавать информацию в ЭВМ низшего уровня

- abstract information
- alpha-numeric dimensional information
- alpha-numeric manufacturing information
- arbitrary information
- average information
- back information
- barcoded information
- billet information
- bulk information
- business information
- camera information
- clear-test information
- coded information
- command information
- control information
- corrective action information
- current information
- cutter preset information
- design information
- digital information
- digitized information
- dimensional information
- directional sinusoid information
- disciplinary information
- documentary information
- edited information
- end-of-life tool information
- engineering information
- external information
- extralinguistic information
- extraneous information
- factual information
- feed-forward information
- function information
- gaging information
- generated wheel form information
- hierarchical information
- historical information
- inhouse information
- initial information
- instantly access actionable information
- interblock information
- intercomputer information
- inventory information
- job information
- legal information
- limit and fit information
- line information
- linguistic information
- locating information
- machining information
- measurement information
- motion information
- multisensor information
- numeric information
- numerical information
- operator information
- out-of-balance information
- part program information
- patent information
- path information
- planning information
- postprocessed information
- precise information
- probability information
- problem-specific information
- process information
- processed information
- product assurance information
- production engineering information
- production information
- product-related information
- prompting information
- rapid information
- raw information
- real-time status information
- redundant information
- reference information
- request information
- retrospective information
- scientific and technical information
- select information
- semantic information
- sensitive information
- sensory information
- setup information
- skill information
- spatial information
- SPC information
- status information
- STI information
- subject information
- summary information
- tactile information
- tape edit information
- technical information
- techno-economic information
- technological information
- temporary information
- tolerance information
- tool management information
- tracking information
- undocumented information
- updated information
- user-selected information
- vital information

English-Russian dictionary of mechanical engineering and automation > information
12 position

1) позиция; положение, заданное положение; координата || устанавливать в положение, устанавливать в заданное положение, позиционировать

2) расположение

•

at a specified position — в заданной позиции; в заданном положении

in a clamped down position — в зафиксированном положении

in a spaced position — на определённом расстоянии

in retracted position — в отведённом положении

to accurately position — точно позиционировать

to anchor in position — зафиксировать в позиции

to bring into an active position — выводить в рабочую позицию, выводить в рабочее положение

to position down — перемещать вниз, перемещаться вниз

to fixedly position — жёстко фиксировать ( одну деталь относительно другой)

to hold the position — сохранять положение, сохранять заданное положение

to manually position — позиционировать вручную; устанавливать вручную

to position up — перемещать вверх, перемещаться вверх

- off position
- on position
- out position
- absolute ordinate slide position
- active position
- actual position
- actuated position
- advanced position
- angular position
- article-capturing position
- at-rest position
- axial position
- best running position
- bevel position
- blank position
- broach position
- broaching position
- buffer position
- carousel positions
- Cartesian positions
- center position
- check position
- clearance position
- closed position
- command position
- commanded drive position
- commanded position
- continuous path position
- coordinate position
- cradle position
- cut-off position
- cutter axial position
- cutting position
- datum position
- dead center position
- defined position
- demand position
- desired load/unload position
- desired position
- disengaging position
- docking position
- down position
- downhand position
- downwardmost position
- dressing position
- dwell position
- dynamic position
- end position
- equally-spaced positions
- equilibrium position
- exchange position
- extreme position
- farthest position
- farthest withdrawn position
- feed position
- fetch position
- final position
- finger-closed position
- finger-open position
- first position
- flat position
- full finger-open position
- full retract position
- full-open position
- fully retracted position
- gaging position
- grasping position
- gravity position
- grind position
- grinding position
- grinding wheel datum position
- gripping position
- home position
- inactive position
- indexed position
- initial position
- initial setup position
- innermost position
- inoperative position
- input position
- instantaneous position
- jaw-loading position
- joint position
- lattice position
- levitating position
- lifted-up position
- lift-off position
- live-tool position
- load/unload position
- locked position
- locking position
- lower position
- lowered position
- lowermost position
- machine tool reference position
- machining position
- manual-off position
- manual-on position
- meshing position
- mid position
- mid-point position
- mid-travel position
- miter position
- neutral position
- nonoperating position
- offset position
- open position
- operating position
- operation-terminating position
- operative position
- operator position
- origin position
- outermost position
- out-of-reach position
- out-of-the way position
- out-of-tolerance position
- output position
- overhead position
- pallet buffer position
- pallet position
- pallet stand position
- pallet storage position
- pallet-loading position
- park position
- parked position
- part interchange position
- part pickup position
- peak-damage position
- pick-up position
- position of load application
- position of minimum out-of-true running
- position of rest
- positive position
- preadjusted cutting position
- prearranged position
- predetermined position
- prepulse position
- prescribed position
- preset position
- previous tool change position
- programmed approach position
- raised position
- ready position
- ready-to-change position
- ready-to-replace position
- ready-to-work position
- reference position
- reference target position
- referenced position
- registered position
- regulating unit position
- relative position
- release position
- reset position
- rest position
- retracted position
- retrieval position
- ring stable position
- robot pick-up position
- robot's position
- rotary tooling position
- rotational position
- running position
- runout position
- safe position
- scanning position
- service position
- setpoint position
- shaft position
- sloping position
- stable equilibrium position
- stall position
- standard position
- standby position
- start position
- static tooling position
- stop position
- storage position
- subreference position
- target levitating position
- target position
- task position
- tilted position
- tool change position
- tool home position
- tool tip position
- tool-gripping position
- tooling buffer position
- tool-loading position
- tool-releasing position
- tool's position
- true position of axis
- true position
- TSS null position
- unknown position
- unlocked position
- unlocking position
- up position
- updated position
- uppermost position
- upwardmost position
- valve position
- waiting position
- weld position
- welding position
- work loading/unloading position
- working position
- workpiece grinding position
- workpiece-loading position
- Z-axis return position
- zero position

English-Russian dictionary of mechanical engineering and automation > position
13 register

1) регистр

2) регистрировать

3) линейка слов ( в ассоциативном ЗУ)

4) точное совпадение; совмещение

5) точно совпадать; совмещать(ся)

•

- accumulator register
- activity register
- addend-partial product register
- adding-storage register
- address register
- address-formation register
- arithmetic register
- balanced-pair storage register
- bank address register
- base address register
- base interrupt address register
- base register
- base-bound register
- base-limit register
- base-of-stack register
- bidirectional shift register
- bound register
- boundary register
- branch register
- breakpoint register
- B-register
- bucket-brigade shift register
- buffer register
- cache control register
- cash register
- charge coupled shift register
- check register
- circulating shift register
- circulation code register
- circulation register
- clock register
- clock-select register
- coincidence register
- command and status register
- command register
- configuration register
- console display register
- control register
- control shift register
- control status register
- coordinate register
- counter register
- current instruction register
- data access register
- data direction register
- data register
- data transfer register
- data-path register
- datum-limit register
- decimation register
- dedicated register
- delay present register
- delay-line register
- descriptor base register
- destination register
- directly addressable register
- display register
- double ranked register
- double register
- double-length register
- double-shift register
- double-word register
- doubling register
- dual shift register
- dynamic register
- edge-triggered register
- equal-word register
- error register
- exchange register
- extension register
- extracode control register
- feedback shift register
- ferromagnetic shift register
- final address register
- flag register
- flag status register
- flip-flop register
- floating-point register
- holding register
- hotline register
- icand register
- ier register
- increment register
- incrementing address register
- index addressing register
- index register
- information register
- input buffer register
- input channel buffer register
- input register
- input-output register
- instruction address register
- instruction counting register
- instruction register
- interface buffer register
- internal function register
- interrogate register
- interrogation register
- interrupt control register
- interrupt register
- interrupt status register
- item activity register
- level status register
- lift-to-right shift register
- limit-of-stack register
- linear feedback shift register
- link register
- linkage register
- load shifting register
- local storage address register
- machine register
- magnetic shift register
- main control register
- main storage data register
- maintenance state register
- mask register
- master-slave shift register
- match/mismatch register
- matched word register
- mechanical buffer register
- memory address register
- memory buffer register
- memory data register
- memory input register
- memory lockout register
- memory pointer register
- memory register
- memory selection register
- memory-information register
- microinstruction register
- modifier register
- motion register
- multiple accumulating register
- multiplicand register
- multiplier register
- multiplier-quotient register
- non-linear feedback shift register
- n-tuple length register
- n-tuple register
- number register
- numerator register
- on-chip address register
- operand address register
- operand register
- operation address register
- operation register
- operational address register
- order register
- ordering function register
- output buffer register
- output channel buffer register
- output register
- output shift register
- page address register
- page register
- parallel register
- partial product register
- partial sum register
- pattern register
- ping-pong register
- pipeline register
- prefix register
- product register
- program address register
- program control register
- program register
- queue register
- quotient register
- read-only storage channel address register
- read-only storage data register
- readout register
- receiving register
- remainder register
- residue register
- result register
- return register
- routing register
- scalar register
- scan-in/scan-out register
- scratchpad register
- search register
- sequence control register
- sequence register
- serial register
- serial/parallel register
- settable register
- setup register
- shadow register
- shift register
- shifting register
- shiftless register
- sign register
- signature register
- single shift register
- sort register
- special-function register
- special-purpose register
- spilled register
- stack register
- standard linkage register
- standby register
- static flip-flop register
- static register
- status register
- stepping register
- storage address register
- storage limits register
- storage register
- sum product register
- switch register
- temporary register
- temporary storage register
- time register
- timed-access register
- top-of-stack register
- trigger register
- user register
- user-visible register
- vacant register
- vector register
- word register
- working register
- X-register
- Y-register

English-Russian dictionary of computer science and programming > register
14 delay

задержка; запаздывание

- absolute delay
- access delay
- adjustable delay
- answering delay
- artificial-time delay
- automatic-call delay
- average-packet delay
- backoff delay
- base-line delay
- cable delay
- call-pass delay
- call-passing delay
- call-queueing delay
- call-setup delay
- connection-establisment delay
- dial-tone sending delay
- differential RGB delays
- drop-cut delay
- envelope delay
- field delay
- fine delay
- fixed delay
- frame delay
- group delay
- half-symbol delay
- handshaking delay
- incoming-response delay
- intranetwork delay
- line delay
- mean queueing delay
- multimode-pulse delay
- on-line delay
- phase delay
- post-dialing delay
- propagation delay
- propagation-time delay
- queueing delay
- rescheduling delay
- retry delay
- sky-wave transmission delay
- stage delay
- through-connection delay
- time delay
- transit delay
- transmit-after-receive time delay
- transmitter-attack time delay
- transmitter-release time delay
- trasmission-path delay
- turn-off delay
- turn-on delay

English-Russian dictionary of telecommunications and their abbreviations > delay

См. также в других словарях:

Open Shortest Path First — (OSPF) is an adaptive routing protocol for Internet Protocol (IP) networks. It uses a link state routing algorithm and falls into the group of interior routing protocols, operating within a single autonomous system (AS). It is defined as OSPF… … Wikipedia
Windows Installer — This article is about the Microsoft Windows component. For the installation of the operating system itself, see Windows Setup. Windows Installer Default window (after running msiexec.exe) Original author(s) Microsoft … Wikipedia
Afshar experiment — The Afshar experiment is an optical experiment which may challenge the principle of complementarity in quantum mechanics, although there is as yet no consensus on this in physics. The result of the experiment, which was first devised and carried… … Wikipedia
Windows Vista networking technologies — This article is part of a series on Windows Vista New features Overview Technical and core system Security and safety Networking technologies I/O technologies Management and administration Removed features … Wikipedia
Features removed from Windows Vista — While Windows Vista contains many new features, a number of capabilities and certain programs that were a part of Windows XP are no longer present or changed, resulting in the removal of certain functionality. The following is a list of features… … Wikipedia
Features new to Windows Vista — This article is part of a series on Windows Vista New features Overview Technical and core system Security and safety Networking technologies I/O technologies Management and administration Removed features … Wikipedia
Glossary of cue sports terms — The following is a glossary of traditional English language terms used in the three overarching cue sports disciplines: carom (or carambole) billiards referring to the various carom games played on a billiard table without pockets; pool (pocket… … Wikipedia
Signaling System 7 — Signaling System #7 (SS7) is a set of telephony signaling protocols which are used to set up most of the world s public switched telephone network telephone calls. The main purpose is to set up and tear down telephone calls. Other uses include… … Wikipedia
Management features new to Windows Vista — This article is part of a series on Windows Vista New features Overview Technical and core system Security and safety Networking technologies I/O technologies Management and administration Removed features … Wikipedia
Ant colony optimization algorithms — Ant behavior was the inspiration for the metaheuristic optimization technique. In computer science and operations research, the ant colony optimization algorithm (ACO) is a probabilistic technique for solving computational problems which can be… … Wikipedia
Clock skew — Contents 1 In circuit design 1.1 Harmful skew 1.2 Beneficial skew 2 On a network 3 Interfaces … Wikipedia

Словари и энциклопедии на Академике

Перевод: со всех языков на русский

setup+path

См. также в других словарях:

Поделиться ссылкой на выделенное

Словари и энциклопедии на Академике

Перевод: со всех языков на русский

setup+path

См. также в других словарях:

Поделиться ссылкой на выделенное

Прямая ссылка: