-
21 tension assignée
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Франко-русский словарь нормативно-технической терминологии > tension assignée
-
22 tension nominale
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
номинальное напряжение конденсатора
Максимальное напряжение, при котором конденсатор может работать в течение минимальной наработки в условиях, указанных в нормативно-технической документации
[ ГОСТ 21415-75]
номинальное напряжение конденсатора
Действующее значение синусоидального переменного напряжения при номинальной частоте, на которое рассчитан конденсатор. Номинальное напряжение многофазного конденсатора - значение напряжения между выводами.
[ ГОСТ 1282-88]Тематики
- конденсаторы для повыш. коэф. мощности
- конденсаторы для электронной аппаратуры
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tension nominale
-
23 Un
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Франко-русский словарь нормативно-технической терминологии > Un
-
24 UN
городская сеть
городская электросеть
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]Тематики
Синонимы
EN
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
3.11 уникальный идентификатор предмета (unique item identifier; UN): Номер, используемый для уникальной идентификации отдельного предмета учета, действительный в течение всего срока его службы.
Примечание 1 - В случае, если радиочастотная метка повторно используется для идентификации другого предмета, то ранее записанный на нее идентификатор предмета должен быть изменен.
Примечание 2 - Уникальный идентификатор Министерства обороны США (DoD Unique Identifier) и электронный код продукции (ЕРС) являются разновидностями идентификатора предмета. Например, идентификатор GS1 SSCC является идентификатором предмета (Item ID; IID) с ограниченным сроком действия, идентификатор GS1 GRAI - идентификатором предмета для присвоения возвратным активам, GS1 sGTIN - идентификатором предмета для присвоения товарной продукции.
Примечание 3 - Вместо термина «уникальный идентификатор предмета» не рекомендуется применять термин «уникальный идентификатор (UID)». То же самое относится к терминам «идентификатор микросхемы», «идентификатор радиочастотной метки» или «идентификатор объекта».
Источник: ГОСТ Р ИСО/МЭК 15963-2011: Информационные технологии. Радиочастотная идентификация для управления предметами. Уникальная идентификация радиочастотных меток оригинал документа
Англо-русский словарь нормативно-технической терминологии > UN
-
25 design voltage
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
3.7 номинальное напряжение (design voltage): Объявленное изготовителем напряжение, к которому относятся все характеристики устройства управления лампами и которое должно быть не менее 85 % наибольшего значения диапазона нормируемого напряжения.
Источник: ГОСТ Р МЭК 61347-1-2011: Устройства управления лампами. Часть 1. Общие требования и требования безопасности оригинал документа
Англо-русский словарь нормативно-технической терминологии > design voltage
-
26 nominal voltage
- номинальное напряжение химического источника тока
- номинальное напряжение пьезоэлектрического (электромеханического) фильтра
- номинальное напряжение аккумулятора
- номинальное напряжение
- напряжение номинальное
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
номинальное напряжение пьезоэлектрического (электромеханического) фильтра (Uном, Unom)
Значение входного напряжения, при котором измеряют параметры пьезоэлектрического (электромеханического) фильтра.
[ ГОСТ 18670-84]Тематики
EN
FR
номинальное напряжение химического источника тока
номинальное напряжение
Условное напряжение, определяемое электрохимической системой химического источника тока.
[ ГОСТ 15596-82]EN
nominal voltage
suitable approximate value of the voltage used to designate or identify a cell, a battery or an electrochemical system
[IEV number 482-03-31]FR
tension nominale, f
valeur approchée appropriée d’une tension, utilisée pour désigner ou identifier un élément, une batterie, ou un système électrochimique
[IEV number 482-03-31]Тематики
Классификация
>>>Синонимы
EN
DE
FR
- tension nominale, f
1.3.2 номинальное напряжение (nominal voltage): Номинальное напряжение герметичного никель-кадмиевого аккумулятора, равное 1,2 В.
Источник: ГОСТ Р МЭК 60622-2010: Аккумуляторы и аккумуляторные батареи, содержащие щелочной и другие некислотные электролиты. Герметичные никель-кадмиевые призматические аккумуляторы оригинал документа
3.3.6 номинальное напряжение аккумулятора (nominal voltage): Номинальное напряжение герметичного никель-металл-гидридного аккумулятора, равное 1,2 В.
Источник: ГОСТ Р МЭК 61951-2-2007: Аккумуляторы и аккумуляторные батареи, содержащие щелочной и другие некислотные электролиты. Портативные герметичные аккумуляторы. Часть 2. Никель-металл-гидрид оригинал документа
3.4 номинальное напряжение (nominal voltage): Подходящее приблизительное значение напряжения, используемое для идентификации напряжения аккумулятора или батареи.
Примечания
1. Номинальное напряжение литиевых аккумуляторов указано в таблице 1.
2. Номинальное напряжение батареи, состоящей из n соединенных последовательно аккумуляторов, равно номинальному напряжению отдельного аккумулятора, увеличенному в n раз.
Источник: ГОСТ Р МЭК 61960-2007: Аккумуляторы и аккумуляторные батареи, содержащие щелочной и другие некислотные электролиты. Аккумуляторы и аккумуляторные батареи литиевые для портативного применения оригинал документа
1.3.2 номинальное напряжение (nominal voltage): Номинальное напряжение открытого никель-кадмиевого аккумулятора с газовой рекомбинацией, равное 1,2 В.
Источник: ГОСТ Р МЭК 60623-2008: Аккумуляторы и аккумуляторные батареи, содержащие щелочной и другие некислотные электролиты. Аккумуляторы никель-кадмиевые открытые призматические оригинал документа
3.22 напряжение номинальное (nominal voltage): Максимально приближенное значение напряжения, принятое для удобства обозначения и идентификации аккумулятора или батареи одной электрохимической системы.
Источник: ГОСТ Р МЭК 62485-2-2011: Батареи аккумуляторные и установки батарейные. Требования безопасности. Часть 2. Стационарные батареи оригинал документа
3.2 номинальное напряжение (nominal voltage): Номинальное напряжение открытого никель-кадмиевого аккумулятора с газовой рекомбинацией, равное 1,2 В.
Источник: ГОСТ Р МЭК 62259-2007: Аккумуляторы и аккумуляторные батареи, содержащие щелочной и другие некислотные электролиты. Аккумуляторы никель-кадмиевые призматические с газовой рекомбинацией оригинал документа
3.15 номинальное напряжение (nominal voltage): Соответствующее приблизительное значение напряжения, которое используют при проектировании или идентификации элемента, батареи или электрохимической системы.
[IEV 482-03-31:2004]
Источник: ГОСТ Р МЭК 60086-4-2009: Батареи первичные. Часть 4. Безопасность литиевых батарей оригинал документа
3.10 номинальное напряжение (nominal voltage): Соответствующее приблизительное значение напряжения, которое используют для идентификации первичной батареи.
Источник: ГОСТ Р МЭК 60086-5-2009: Батареи первичные. Часть 5. Безопасность батарей с водным электролитом оригинал документа
3.18 номинальное напряжение (nominal voltage) Un: Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
Источник: ГОСТ Р 51317.4.30-2008: Электрическая энергия. Совместимость технических средств электромагнитная. Методы измерений показателей качества электрической энергии оригинал документа
3.17 номинальное напряжение (nominal voltage): Номинальное значение напряжения, которое определяет тип источника питания.
Источник: ГОСТ Р 55266-2012: Совместимость технических средств электромагнитная. Оборудование сетей связи. Требования и методы испытаний оригинал документа
Англо-русский словарь нормативно-технической терминологии > nominal voltage
-
27 rated voltage
- регламентированное напряжение
- расчетное напряжение
- нормируемое напряжение
- номинальное напряжение конденсатора
- номинальное напряжение (во взрывозащите)
- номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
номинальное напряжение
Значение напряжения, на которое рассчитаны рабочие и эксплуатационные характеристики распределенных электронагревателей.
[ ГОСТ Р МЭК 60050-426-2006]
Тематики
EN
номинальное напряжение конденсатора
Максимальное напряжение, при котором конденсатор может работать в течение минимальной наработки в условиях, указанных в нормативно-технической документации
[ ГОСТ 21415-75]
номинальное напряжение конденсатора
Действующее значение синусоидального переменного напряжения при номинальной частоте, на которое рассчитан конденсатор. Номинальное напряжение многофазного конденсатора - значение напряжения между выводами.
[ ГОСТ 1282-88]Тематики
- конденсаторы для повыш. коэф. мощности
- конденсаторы для электронной аппаратуры
EN
DE
FR
нормируемое напряжение
Питающее напряжение или напряжение, на которое светильник рассчитан изготовителем.
[ ГОСТ Р МЭК 60598-1-2014]Тематики
- лампы, светильники, приборы и комплексы световые
EN
расчетное напряжение
номинальное напряжение
нормальное эксплуатационное напряжение
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]Тематики
Синонимы
EN
расчётное напряжение
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999]Тематики
- электротехника, основные понятия
EN
3.17 номинальное напряжение (rated voltage): Напряжение, установленное для выключателя изготовителем.
Источник: ГОСТ Р 51324.1-2005: Выключатели для бытовых и аналогичных стационарных электрических установок. Часть 1. Общие требования и методы испытаний оригинал документа
1.5.10 номинальное напряжение (rated voltage): Номинальное напряжение - это либо эффективное значение рабочего напряжения номинальной частоты, либо рабочее постоянное напряжение, которое можно длительно подавать на выводы конденсатора при любой температуре между нижней и верхней температурами категории. Это означает, что у конденсаторов, на которые распространяется настоящий стандарт, напряжение категории равно номинальному напряжению.
Источник: ГОСТ Р МЭК 60384-14-2004: Конденсаторы постоянной емкости для электронной аппаратуры. Часть 14. Групповые технические условия на конденсаторы постоянной емкости для подавления электромагнитных помех и соединения с питающими магистралями оригинал документа
3.2.1 номинальное напряжение (rated voltage): Напряжение, указанное изготовителем для этой машины, или напряжение между фазами (линейное) - при трехфазном питании.
Источник: ГОСТ Р МЭК 60745-1-2005: Машины ручные электрические. Безопасность и методы испытаний. Часть 1. Общие требования оригинал документа
3.25 номинальное напряжение (rated voltage): Напряжение, установленное изготовителем соединителей, которое указывается в стандартах или технических условиях.
Источник: ГОСТ Р 51322.1-2011: Соединители электрические штепсельные бытового и аналогичного назначения. Часть 1. Общие требования и методы испытаний оригинал документа
3.4 номинальное напряжение (rated voltage): Напряжение или диапазон напряжений, маркируемый на лампе.
Источник: ГОСТ Р 53881-2010: Лампы со встроенными пускорегулирующими аппаратами для общего освещения. Требования безопасности оригинал документа
3.23 номинальное напряжение (rated voltage): Значение напряжения, на которое рассчитаны рабочие и эксплуатационные характеристики распределенных электронагревателей.
Источник: ГОСТ Р МЭК 60079-30-1-2009: Взрывоопасные среды. Резистивный распределенный электронагреватель. Часть 30-1. Общие технические требования и методы испытаний оригинал документа
1.5.9 номинальное напряжение (rated voltage): Напряжение или диапазон напряжения, заданное(ый) в соответствии с настоящим стандартом.
Примечание - Если в маркировке на лампе приведен диапазон напряжения, это значит, что возможна эксплуатация ламп при любом значении напряжения в пределах этого диапазона.
Источник: ГОСТ Р 52706-2007: Лампы накаливания вольфрамовые для бытового и аналогичного общего освещения. Эксплуатационные требования оригинал документа
2.1 нормируемое напряжение (rated voltage): Максимальное рабочее напряжение, заявленное изготовителем, на которое рассчитан патрон.
Источник: ГОСТ Р МЭК 60838-1-2008: Патроны различные для ламп. Часть 1. Общие требования и методы испытаний оригинал документа
1.2.1.1. номинальное напряжение (rated voltage): Указанное изготовителем напряжение источника сетевого электропитания (для трехфазного источника электропитания принимают линейное напряжение).
Источник: ГОСТ Р МЭК 60950-1-2009: Оборудование информационных технологий. Требования безопасности. Часть 1. Общие требования оригинал документа
1.2.1.1 номинальное напряжение (rated voltage): Указанное изготовителем напряжение источника сетевого электропитания (для трехфазного источника электропитания принимают линейное напряжение).
Источник: ГОСТ Р МЭК 60950-1-2005: Оборудование информационных технологий. Требования безопасности. Часть 1. Общие требования оригинал документа
3.37 номинальное напряжение (rated voltage): Значение напряжения для заданных условий эксплуатации.
Значение и условия должны быть указаны в соответствующем стандарте или изготовителем, или ответственным поставщиком.
Примечание - Номинальное напряжение выражают в вольтах (В).
Источник: ГОСТ Р 54814-2011: Светодиоды и светодиодные модули для общего освещения. Термины и определения оригинал документа
3.4 номинальное напряжение (rated voltage): Напряжение, указанное для прибора производителем.
Источник: ГОСТ Р МЭК 62301-2011: Приборы бытовые электрические. Измерение потребляемой мощности в режиме ожидания оригинал документа
1.3.4 номинальное напряжение (rated voltage): Напряжение или диапазон напряжения, заданное(ый) в соответствии с настоящим стандартом.
Примечание - Если в маркировке на лампе приведен диапазон напряжения, это значит, что возможна эксплуатация ламп при любом значении напряжения в пределах этого диапазона.
Источник: ГОСТ Р 52712-2007: Требования безопасности для ламп накаливания. Часть 1. Лампы накаливания вольфрамовые для бытового и аналогичного общего освещения оригинал документа
3.40 номинальное напряжение (rated voltage): Напряжение, установленное для машины изготовителем. При трехфазном питании - напряжение между фазами.
Источник: ГОСТ Р МЭК 60745-1-2009: Машины ручные электрические. Безопасность и методы испытаний. Часть 1. Общие требования оригинал документа
3.2.1 номинальное напряжение (rated voltage): Напряжение, указанное изготовителем для этой машины, или напряжение между фазами (линейное) - при трехфазном питании.
3.11 номинальное напряжение (rated voltage), UH (UN): Напряжение при номинальной частоте, прикладываемое между линейными выводами обмотки.
Источник: ГОСТ Р 54801-2011: Трансформаторы тяговые и реакторы железнодорожного подвижного состава. Основные параметры и методы испытаний оригинал документа
1.3.4 номинальное напряжение (rated voltage): Напряжение или диапазон напряжений, маркируемые на лампе.
Источник: ГОСТ Р 53879-2010: Лампы со встроенными пускорегулирующими аппаратами для общего освещения. Эксплуатационные требования оригинал документа
3.2 номинальное напряжение (rated voltage): Напряжение или диапазон напряжений, маркируемый на лампе.
Источник: ГОСТ Р МЭК 62560-2011: Лампы светодиодные со встроенным устройством управления для общего освещения на напряжения свыше 50 В. Требования безопасности оригинал документа
3.103 номинальное напряжение (rated voltage): Напряжение, указанное изготовителем, для конкретного корпуса.
Источник: ГОСТ Р 50827.5-2009: Коробки и корпусы для электрических аппаратов, устанавливаемые в стационарные электрические установки бытового и аналогичного назначения. Часть 24. Специальные требования к коробкам и корпусам, предназначенным для установки защитных и аналогичных аппаратов с большой рассеиваемой мощностью оригинал документа
3.2.1 номинальное напряжение (rated voltage); Ur:Междуфазное напряжение на выводах генератора при номинальных частоте и мощности.
Примечание - Номинальное напряжение генератора для рабочих и эксплуатационных характеристик устанавливает изготовитель.
Источник: ГОСТ Р 53986-2010: Электроагрегаты генераторные переменного тока с приводом от двигателя внутреннего сгорания. Часть 3. Генераторы переменного тока оригинал документа
3.2.1. номинальное напряжение (rated voltage):
Напряжение, для которого сконструирована установка (или ее часть).
Источник: ГОСТ Р МЭК 60519-1-2005: Безопасность электротермического оборудования. Часть 1. Общие требования оригинал документа
3.1.1 номинальное напряжение (rated voltage): Напряжение, установленное изготовителем для прибора.
Источник: ГОСТ Р 52161.1-2004: Безопасность бытовых и аналогичных электрических приборов. Часть 1. Общие требования оригинал документа
2.3 номинальное напряжение (rated voltage): Стандартное напряжение, на которое рассчитан кабель и которое служит для определения параметров электрических испытаний.
Источник: ГОСТ Р МЭК 60245-1-2006: Кабели с резиновой изоляцией на номинальное напряжение до 450/750 В включительно. Часть 1. Общие требования оригинал документа
2.3 номинальное напряжение (rated voltage): Стандартное напряжение, на которое рассчитан кабель и которое служит для определения параметров электрических испытаний.
Примечание 1 - Номинальное напряжение выражается сочетанием двух значений U0/U, выраженных в вольтах (В):
U0 - среднеквадратическое значение между любой изолированной жилой и «землей» (металлическим покрытием кабеля или окружающей средой);
U - среднеквадратическое значение между любыми двумя фазными жилами многожильного кабеля или системы одножильных кабелей.
В системе переменного тока номинальное напряжение кабеля должно быть не менее номинального напряжения системы, для которой он предназначен.
Это условие относится как к значению U0, так и к значению U.
В системе постоянного тока номинальное напряжение системы должно быть не более полуторного значения номинального напряжения кабеля.
Примечание 2 - Рабочее напряжение системы может постоянно превышать номинальное напряжение такой системы до 10 %. Кабель можно использовать при рабочем напряжении на 10 % выше его номинального напряжения, если последнее по крайней мере равно номинальному напряжению системы.
Источник: ГОСТ Р МЭК 60245-1-2009: Кабели с резиновой изоляцией на номинальное напряжение до 450/750 В включительно. Часть 1. Общие требования оригинал документа
1.2.11 нормируемое напряжение (rated voltage): Питающее напряжение или напряжение, на которое светильник рассчитан изготовителем.
Источник: ГОСТ Р МЭК 60598-1-2011: Светильники. Часть 1. Общие требования и методы испытаний оригинал документа
2.3 номинальное напряжение (rated voltage): Стандартное напряжение, на которое рассчитан кабель, служащее для определения параметров электрических испытаний.
Номинальное напряжение выражают сочетанием двух значений - U0/U, выраженных в вольтах:
U0- среднеквадратическое значение между любой изолированной жилой и «землей» (металлическим покрытием кабеля или окружающей средой);
U - среднеквадратическое значение между любыми двумя фазными жилами многожильного кабеля или системы одножильных кабелей.
В системе переменного тока номинальное напряжение кабеля должно быть не менее номинального напряжения системы, для которого он предназначен.
Это требование относится как к значению U0, так и к значению U.
В системе постоянного тока номинальное напряжение системы должно быть не более полуторного значения номинального напряжения кабеля.
Примечание - Рабочее напряжение системы может постоянно превышать номинальное напряжение этой системы до 10 %. Кабель можно использовать при рабочем напряжении, на 10 % превышающем номинальное напряжение, если последнее по крайней мере равно номинальному напряжению системы.
Источник: ГОСТ Р МЭК 60227-1-2009: Кабели с поливинилхлоридной изоляцией на номинальное напряжение до 450/750 В включительно. Часть 1. Общие требования оригинал документа
3.2.4 регламентированное напряжение (rated voltage): Входное или выходное напряжение (напряжение фаза - фаза для трехфазного источника питания), указанное производителем.
Источник: ГОСТ Р 55061-2012: Совместимость технических средств электромагнитная. Статические системы переключения. Часть 2. Требования и методы испытаний оригинал документа
Англо-русский словарь нормативно-технической терминологии > rated voltage
-
28 voltage
1) напряжение, разность потенциалов2) потенциал•- accelerating voltagevoltage across — напряжение на (напр. зажимах)
- acceleration voltage
- active voltage
- actuating voltage
- allowable voltage
- alternating voltage
- anode voltage
- anode breakdown voltage
- anode-cathode voltage
- anode-to-cathode voltage
- applied voltage
- arc voltage
- arc-drop voltage
- asymptotic breakdown voltage
- avalanche voltage
- avalanche breakdown voltage
- average voltage
- back voltage
- balanced voltages
- barrier voltage
- base voltage
- baseband voltage
- base-to-emitter voltage
- bath voltage
- bias voltage
- birefringence threshold voltage
- black-out voltage
- blanking voltage
- blocking voltage
- blue video voltage
- booster voltage
- branch voltage
- breakdown voltage
- breakover voltage
- bridge supply voltage
- bucking voltage
- built-in voltage
- bus voltage
- calibration voltage
- capacitor voltage
- catcher voltage
- cathode voltage
- cathode sheath voltage
- cathode storage-element equilibrium voltage
- cell voltage
- charge voltage
- circuit voltage
- clamp voltage
- clock voltage
- closed-circuit voltage
- coercive voltage
- collector voltage
- collector breakdown voltage
- collector storage-element equilibrium voltage
- collector-to-base voltage
- collector-to-emitter voltage
- color voltage
- commercial-frequency voltage
- common-mode voltage
- commutating voltage
- compensating voltage
- complex voltage
- compliance voltage
- composite controlling voltage
- computer voltage
- constant voltage
- contact voltage
- control voltage
- control-circuit voltage
- convergence voltage
- corona start voltage
- counter voltage
- crest voltage
- critical voltage
- critical anode voltage
- critical grid voltage
- crossover voltage
- current-resistance voltage
- cutoff voltage
- dc voltage
- decelerating voltage
- decomposition voltage
- deflecting voltage
- derivative voltage
- dielectric breakdown voltage
- differential-mode voltage
- dipole voltage
- dipole barrier voltage
- direct voltage
- discharge voltage
- disruptive discharge voltage
- domain voltage
- drain voltage
- driving voltage
- drop-away voltage
- drop-out voltage
- effective voltage
- electric voltage
- electrode voltage
- emitter voltage
- equilibrium voltage
- error voltage
- excess voltage
- excess domain voltage
- excitation voltage
- extinction voltage
- extinguishing voltage
- extra-high voltage
- Faraday voltage
- field voltage
- filament voltage
- final voltage
- firing voltage
- first breakdown voltage
- first crossover voltage
- flashback voltage
- flashover voltage
- flat-band voltage
- floating voltage
- fluctuation voltage
- flyback voltage
- focusing voltage
- formation voltage
- forming voltage
- forward voltage
- forward breakover voltage
- forward gate voltage
- fuel-cell voltage
- gate voltage
- gate nontrigger voltage
- gate trigger voltage
- gate turn-off voltage
- generated voltage
- gradient-established storage-element equilibrium voltage
- green-video voltage
- grid voltage
- half-wave voltage
- Hall voltage
- heater voltage
- high voltage
- high-level voltage
- holding voltage
- ignition voltage
- impressed voltage
- induced voltage
- inflection-point voltage
- initial voltage
- initial inverse voltage
- injected voltage
- in-phase voltage
- input voltage
- input error voltage
- interference voltage
- internal correction voltage
- inverse voltage
- ionization voltage
- junction voltage
- keep-alive voltage
- kickback voltage
- line voltage
- link voltage
- load voltage
- logical-threshold voltage
- low-level voltage
- magnetron critical voltage
- mains voltage
- maintaining voltage
- mask voltage
- minimum off-state voltage
- neutralizing voltage
- node voltage
- node-to-datum voltage
- noise voltage
- no-load voltage
- nominal voltage
- offset voltage
- off-load voltage
- off-state voltage
- on-load voltage
- on-state voltage
- open-circuit voltage
- operating voltage
- oscillating voltage
- out-of-balance voltages
- out-of-phase voltage
- output voltage
- output offset voltage
- pace voltage
- peak voltage
- peak inverse voltage
- peak-point voltage
- peak reverse voltage
- peak-to-peak voltage
- periodic voltage
- permissible voltage
- phase voltage
- photoelectric voltage
- pickup voltage
- pinch-off voltage
- plate voltage
- polarizing voltage
- poling voltage
- primary voltage
- principal voltage
- projected peak-point voltage
- psophometric voltage
- pull-in voltage
- pulsating voltage
- pump voltage
- punch-through voltage
- puncture voltage
- push-pull voltages
- push-push -voltages
- rail voltage
- rated voltage
- rated impulse withstand voltage
- reactive voltage
- rectified voltage
- rectifier-load voltage
- red video voltage
- reference voltage
- reflector voltage
- reignition voltage
- residual voltage
- resistance voltage
- resonance voltage
- reverse voltage
- reverse-bias voltage
- reverse-bias breakdown voltage
- ripple voltage
- root-mean-square voltage
- saturation voltage
- sawtooth voltage
- scanning voltage
- screen-grid voltage
- secondary voltage
- secondary-emission crossover voltage
- second-crossover voltage
- self-breakdown voltage
- self-firing voltage
- self-induction voltage
- shot-noise voltage
- signal voltage
- single-ended input voltage
- single-ended output voltage
- sinusoidal voltage
- source voltage
- square-wave voltage
- stabilized voltage
- staircase voltage
- starter breakdown voltage
- starting voltage
- step voltage
- storage-element equilibrium voltage
- supply voltage
- surge voltage
- sweep voltage
- swing voltage
- switching voltage
- synchronousvoltage
- tank voltage
- target voltage
- temperature voltage
- thermocouple voltage
- thermoelectric voltage
- threshold voltage
- time-base voltage
- touch voltage
- tree-branch voltage
- tunnel breakdown voltage
- ultrahigh voltage
- unit step voltage
- valley voltage
- variable voltage
- working voltage
- Zener voltage -
29 impedance
полное сопротивление, импеданс- acoustic impedance
- anode impedance
- antenna input impedance
- backward impedance
- biasing impedance
- capacitance impedance
- cathode impedance
- characteristic acoustic impedance
- circuit impedance
- complex impedance
- dynamic input impedance
- dynamic output impedance
- forward impedance
- free impedance
- ground impedance
- inductive impedance
- input impedance
- line impedance
- load impedance
- loop impedance
- matched impedance
- matching impedance
- mutual impedance
- negative impedance
- normal impedance
- open-circuit impedance
- output impedance
- plate-load impedance
- radiation impedance
- reciprocal impedance
- reflected impedance
- rejector-dynamic impedance
- screen impedance
- source impedance
- suitable load impedance
- surge impedance
- wave impedanceEnglish-Russian dictionary of telecommunications and their abbreviations > impedance
-
30 mode
məud сущ.
1) метод, методика, способ The writer made use of a mode of teaching used commonly enough in the Bible. ≈ Писатель использует тот наставительный способ изложения, который достаточно часто применяется в Библии. mode of production Syn: method, manner, means
2) образ действий, манера поведения He explained it in his usual solemn mode. ≈ Он объяснил это в своей обычной важной манере. mode of life Syn: fashion
1.
3) вид, форма
4) состояние, режим a spacecraft in reentry mode ≈ космический корабль, находящийся в плотных слоях атмосферы when the camera is in automatic mode ≈ когда камера находится в автоматическом режиме Syn: status
5) стиль;
мода;
обычай It is the mode to live high, to spend more than we get. ≈ Это обычай жить богато, тратить больше, чем мы получаем. a slightly more elegant and formal mode of dress ≈ слегка более элегантный и формальный стиль одежды Syn: fashion
1., vogue, style
1.
6) муз. лад, тональность
7) грам.;
редк. наклонение Syn: mood II
8) лог. модальность суждения метод, способ - * of production (политэкономия) способ производства - * of publication способ издания( книг) - * of operation( специальное) способ или режим работы образ действий;
манера - * of life образ жизни - * of speaking манера говорить форма, вид - * of publication форма /вид/ издания (книг) - musical and literary *s of expression музыкальная и литературная формы выражения - * of combat( военное) вид боевых действий - * of decay( физическое) тип /форма, схема/ распада мода, обычай - today such a thing is the * сейчас такие вещи не в моде;
теперь мода на такие вещи - after the * of France на французский манер /лад/;
по французскому обычаю;
как принято во Франции (грамматика) (устаревшее) наклонение (музыкальное) лад, тональность (логика) модальность суждения (геология) действительный минералогический состав породы мода (в математической статистике) (физическое) тип движения;
мода (напр. колебаний) access ~ вчт. режим доступа addressing ~ вчт. способ адресации append ~ вчт. режим дозаписи attraction ~ вчт. демонстрационный режим auto-indent ~ вчт. режим автоматического отступа background ~ вчт. фоновый режим base ~ вчт. базовый режим batch ~ вчт. пакетный режим block ~ вчт. блочный режим broadcast ~ вчт. режим рассылки burst ~ вчт. монопольный режим capitals ~ вчт. режим прописных букв command ~ вчт. командный режим communication ~ вчт. режим связи compatibility ~ вчт. режим эмуляции compute ~ вчт. режим счета contention ~ вчт. состязательный режим conversational ~ вчт. диалоговый режим data-in ~ вчт. режим ввода данных data-out ~ вчт. режим вывода данных dialog ~ вчт. диалоговый режим display ~ вчт. экранный режим dual-processor ~ вчт. двухпроцессорный режим edit ~ вчт. режим редактирования event input ~ вчт. ввод с очередями failure ~ вчт. вид отказа file ~ вчт. режимный код файла fly-through ~ вчт. режим наблюдения с высоты птичьего полета free-running ~ вчт. режим свободного доступа full-screen ~ вчт. полноэкранный режим graphic ~ вчт. графический режим graphics ~ вчт. графический режим help ~ вчт. консультативный режим idle ~ вчт. нерабочий режим indexed ~ вчт. режим индексирования insert ~ вчт. режим вставки interactive ~ вчт. диалоговый режим interactive ~ вчт. интерактивный режим interpretive ~ вчт. режим интерпретации inverse video ~ вчт. режим выдачи негативного изображения kernel ~ вчт. режим ядра keyboard ~ вчт. клавиатурный режим learn ~ вчт. режим обучения local ~ вчт. автономный режим lock ~ вчт. режим блокировки manual ~ вчт. ручной режим mapped ~ вчт. режим с управлением памятью master ~ вчт. привелигированный режим mode вид ~ муз. лад, тональность ~ метод, способ;
mode of production способ производства ~ метод ~ мода;
обычай ~ образ ~ образ действий;
mode of life образ жизни ~ принцип работы ~ вчт. режим ~ способ ~ форма, вид ~ форма ~ of communication способ связи ~ of communication средство общения ~ образ действий;
mode of life образ жизни ~ of operation метод работы ~ of operation принцип работы ~ of operation способ действия ~ of payment форма платежа ~ метод, способ;
mode of production способ производства move ~ вчт. режим пересылки multitask ~ вчт. многозадачный режим native ~ вчт. режим работы в собственной системе команд nonwrap ~ вчт. режим без автоматического перевода строки off-line ~ вчт. автономный режим on-line ~ вчт. оперативный режим operating ~ вчт. рабочий режим page ~ вчт. страничный режим pipeline ~ вчт. конвейерный режим posted-write ~ вчт. режим отложенной записи privileged ~ вчт. привилегированный режим query ~ вчт. справочный режим question-answer ~ вчт. вопросно-ответный режим ready ~ вчт. режим готовности real address ~ вчт. режим реальной адресации real ~ вчт. реальный режим real time ~ вчт. режим реального времени replace ~ вчт. режим замещения run ~ вчт. режим прогона scope ~ вчт. экранный режим screen ~ вчт. экранный режим slave ~ вчт. непривилегированный режим slotted ~ вчт. режим с выделением квантов времени split-screen ~ вчт. полиэкранный режим spy ~ вчт. режим контрольных точек stream ~ вчт. пакетный режим supervisor ~ вчт. режим супервизора task ~ вчт. режим задачи test ~ вчт. тестовый режим text ~ вчт. текстовый режим through ~ вчт. режим работы на проход total-failure ~ вчт. режим полного отказа tracing ~ вчт. режим трассировки tracking-cross ~ вчт. режим отслеживания training ~ вчт. режим обучения transparent ~ вчт. прозрачный режим unoperable ~ вчт. режим простоя usage ~ вчт. режим использования user ~ вчт. режим пользователя user-operation ~ вчт. пользовательский режим verification ~ вчт. режим контроля virtual address ~ вчт. режим виртуальной адресации wave ~ тип волны wave ~ тип колебаний wrong ~ вчт. неверно выбранный режим -
31 press
1) (печатная) машина; уст. печатный станок2) пресс || прессовать; давить3) пресса; печать || печатать4) типография5) издательство6) тиражный оттиск7) нажимать (клавишу)- in press- D-pressАнгло-русский словарь по полиграфии и издательскому делу > press
-
32 system
система; комплекс; средство; способ; метод; сеть (напр. дорог) ;aiming-navigation system (analog, digital) — прицельно-навигационная система (аналоговая, цифровая)
air observation, acquisition and fire control system — (бортовая) система воздушной разведки, засечки целей и управления огнем
air support aircraft ECM (equipment) system — (бортовая) система РЭП для самолетов авиационной поддержки
airborne (ground) target acquisition and illumination laser system — ав. бортовая лазерная система обнаружения и подсветки (наземных) целей
airborne (ground) targeting and laser designator system — ав. бортовая лазерная система обнаружения и целеуказания (наземных целей)
airborne laser illumination, ranging and tracking system — ав. бортовая система лазерной подсветки, определения дальности и сопровождения цели
artillery (nuclear) delivery system — артиллерийская система доставки (ядерного) боеприпаса (к цели)
C2 system — система оперативного управления; система руководства и управления
C3 system — система руководства, управления и связи; система оперативного управления и связи
channel and message switching (automatic) communications system — АСС с коммутацией каналов и сообщений
country-fair type rotation system (of instruction) — метод одновременного обучения [опроса] нескольких учебных групп (переходящих от одного объекта изучения к другому)
dual-capable (conventional/nuclear) weapon delivery system — система доставки (обычного или ядерного) боеприпаса к цели
electromagnetic emitters identification, location and suppression system — система обнаружения, опознавания и подавления источников электромагнитных излучений [излучающих РЭС]
field antimissile (missile) system — полевой [войсковой] ПРК
fire-on-the-move (air defense) gun system — подвижный зенитный артиллерийский комплекс для стрельбы в движении [на ходу]
fluidic (missile) control system — ркт. гидравлическая [струйная] система управления полетом
forward (area) air defense system — система ПВО передового района; ЗРК для войсковой ПВО передового района
graduated (availability) operational readiness system — Бр. система поэтапной боевой готовности (частей и соединений)
high-resolution satellite IR detection, tracking and targeting system — спутниковая система с ИК аппаратурой высокой разрешающей способности для обнаружения, сопровождения целей и наведения средств поражения
ICBM (alarm and) early warning satellite system — спутниковая система обнаружения пусков МБР и раннего предупреждения (средств ПРО)
information storage, tracking and retrieval system — система накопления, хранения и поиска информации
instantaneous grenade launcher (armored vehicle) smoke system — гранатомет (БМ) для быстрой постановки дымовой завесы
Precision Location [Locator] (and) Strike system — высокоточная система обеспечения обнаружения и поражения целей; высокоточный разведывательно-ударный комплекс
rapid deceleration (parachute) delivery system — парашютная система выброски грузов с быстрым торможением
real time, high-resolution reconnaissance satellite system — спутниковая разведывательная система с высокой разрешающей способностью аппаратуры и передачей информации в реальном масштабе времени
received signal-oriented (output) jamming signal power-adjusting ECM system — система РЭП с автоматическим регулированием уровня помех в зависимости от мощности принимаемого сигнала
sea-based nuclear (weapon) delivery system — система морского базирования доставки ядерного боеприпаса к цели
small surface-to-air ship self-defense (missile) system — ЗРК ближнего действия для самообороны корабля
Status Control, Alerting and Reporting system — система оповещения, контроля и уточнения состояния [боевой готовности] сил и средств
surface missile (weapon) system — наземный [корабельный] РК
target acquisition, rapid designation and precise aiming system — комплекс аппаратуры обнаружения цели, быстрого целеуказания и точного прицеливания
— ABM defense system— antimissile missile system— central weapon system— countersurprise military system— laser surveying system— tank weapon system— vertical launching system— weapons system -
33 mode
[məud]access mode вчт. режим доступа addressing mode вчт. способ адресации append mode вчт. режим дозаписи attraction mode вчт. демонстрационный режим auto-indent mode вчт. режим автоматического отступа background mode вчт. фоновый режим base mode вчт. базовый режим batch mode вчт. пакетный режим block mode вчт. блочный режим broadcast mode вчт. режим рассылки burst mode вчт. монопольный режим capitals mode вчт. режим прописных букв command mode вчт. командный режим communication mode вчт. режим связи compatibility mode вчт. режим эмуляции compute mode вчт. режим счета contention mode вчт. состязательный режим conversational mode вчт. диалоговый режим data-in mode вчт. режим ввода данных data-out mode вчт. режим вывода данных dialog mode вчт. диалоговый режим display mode вчт. экранный режим dual-processor mode вчт. двухпроцессорный режим edit mode вчт. режим редактирования event input mode вчт. ввод с очередями failure mode вчт. вид отказа file mode вчт. режимный код файла fly-through mode вчт. режим наблюдения с высоты птичьего полета free-running mode вчт. режим свободного доступа full-screen mode вчт. полноэкранный режим graphic mode вчт. графический режим graphics mode вчт. графический режим help mode вчт. консультативный режим idle mode вчт. нерабочий режим indexed mode вчт. режим индексирования insert mode вчт. режим вставки interactive mode вчт. диалоговый режим interactive mode вчт. интерактивный режим interpretive mode вчт. режим интерпретации inverse video mode вчт. режим выдачи негативного изображения kernel mode вчт. режим ядра keyboard mode вчт. клавиатурный режим learn mode вчт. режим обучения local mode вчт. автономный режим lock mode вчт. режим блокировки manual mode вчт. ручной режим mapped mode вчт. режим с управлением памятью master mode вчт. привелигированный режим mode вид mode муз. лад, тональность mode метод, способ; mode of production способ производства mode метод mode мода; обычай mode образ mode образ действий; mode of life образ жизни mode принцип работы mode вчт. режим mode способ mode форма, вид mode форма mode of communication способ связи mode of communication средство общения mode образ действий; mode of life образ жизни mode of operation метод работы mode of operation принцип работы mode of operation способ действия mode of payment форма платежа mode метод, способ; mode of production способ производства move mode вчт. режим пересылки multitask mode вчт. многозадачный режим native mode вчт. режим работы в собственной системе команд nonwrap mode вчт. режим без автоматического перевода строки off-line mode вчт. автономный режим on-line mode вчт. оперативный режим operating mode вчт. рабочий режим page mode вчт. страничный режим pipeline mode вчт. конвейерный режим posted-write mode вчт. режим отложенной записи privileged mode вчт. привилегированный режим query mode вчт. справочный режим question-answer mode вчт. вопросно-ответный режим ready mode вчт. режим готовности real address mode вчт. режим реальной адресации real mode вчт. реальный режим real time mode вчт. режим реального времени replace mode вчт. режим замещения run mode вчт. режим прогона scope mode вчт. экранный режим screen mode вчт. экранный режим slave mode вчт. непривилегированный режим slotted mode вчт. режим с выделением квантов времени split-screen mode вчт. полиэкранный режим spy mode вчт. режим контрольных точек stream mode вчт. пакетный режим supervisor mode вчт. режим супервизора task mode вчт. режим задачи test mode вчт. тестовый режим text mode вчт. текстовый режим through mode вчт. режим работы на проход total-failure mode вчт. режим полного отказа tracing mode вчт. режим трассировки tracking-cross mode вчт. режим отслеживания training mode вчт. режим обучения transparent mode вчт. прозрачный режим unoperable mode вчт. режим простоя usage mode вчт. режим использования user mode вчт. режим пользователя user-operation mode вчт. пользовательский режим verification mode вчт. режим контроля virtual address mode вчт. режим виртуальной адресации wave mode тип волны wave mode тип колебаний wrong mode вчт. неверно выбранный режим -
34 range
2) зона; область3) амплитуда, размах ( колебаний) || колебаться в пределах4) вчт. семейство; множество значений; область значений6) дальность [радиус\] действия7) геофиз. дистанция9) ряд || располагать в ряд10) строит. ряд кладки12) мор. створ13) класс || классифицировать; систематизировать15) полигон16) направление17) (кухонная) плита18) экол. ареал, область обитания19) геод. провешивать линию20) простираться; иметь указанную дальность действия•to adjust over a limited range — регулировать в ограниченных пределах;to extend flight range — увеличивать дальность полёта;to extend the measurement range — расширять диапазон [пределы\] измерений-
normal oreing range
-
adhesive tack range
-
adjustment range
-
aileron range
-
aircraft capacity range
-
aircraft operational range
-
aircraft range
-
altitude range
-
angle-of-attack range
-
angular range
-
annealing range
-
annual range
-
antenna range
-
aperture range
-
austenitic range
-
ball center range
-
blind range
-
blue brittle temperature range
-
blue brittle range
-
boiling range
-
boring range
-
built-in range
-
calibration range
-
capacitance range
-
capacity range
-
capture range
-
carrier-frequency range
-
category temperature range
-
center of gravity range
-
centralized traffic control range
-
close-to-critical range
-
comfort range
-
compressive shrinking range
-
contrast range
-
control range
-
cooling range
-
correction range
-
counter range
-
coupling range
-
cruising range
-
day visibility range
-
delivery range
-
detection range
-
devitrification range
-
diaphragm range
-
direct-reading range
-
discrete range
-
distillation range
-
diurnal range
-
dynamic range
-
ecological range
-
effective range
-
elastic range of stress
-
elastic unloading range
-
electrical range
-
electronic tuning range
-
enlargement range
-
entrance range
-
environmental range
-
error range
-
excursion range
-
expanded range
-
exposure range
-
extended range
-
extreme range
-
ferritic range
-
ferry range
-
film dynamic range
-
firing range
-
flight service range
-
flight visual range
-
flow temperature range
-
flying range
-
focal length variation range
-
focusing range
-
forecast range
-
freak range
-
free spectral range
-
freezing range
-
frequency range
-
frequency tuning range
-
fuel explosive range
-
fuel range
-
fusion range
-
gasoline range
-
glass-forming range
-
glass-transition range
-
gripping range
-
ground range
-
hardening range
-
head range
-
hold-in range
-
holding range
-
horizontal range
-
hydraulic fluid temperature range
-
ignition range
-
indication range
-
inflammability range
-
input range
-
input voltage range
-
instrument range
-
interlocking range
-
intermediate range
-
intrinsic range
-
legitimate range
-
linear range
-
line-of-sight range
-
lock-in range
-
locking range
-
lock-on range
-
lug speed range
-
luminance range
-
machining range
-
magnification range
-
mapping range
-
martensite decomposition range
-
mass range
-
measurement range
-
mechanical tuning range
-
melting range
-
meteorological optical range
-
meter range
-
movement range
-
multitrack range
-
nighttime visual range
-
night visual range
-
number range
-
oblique visual range
-
omnidirectional range
-
on-scale range
-
operating free-air temperature range
-
operating pressure range
-
operating range
-
operating temperature range
-
operating voltage range
-
operative range
-
optical range
-
overlapping ranges
-
penetration range
-
pipe range
-
plastic range of stress
-
point size range
-
power range
-
projected range
-
pull-in range
-
radar range
-
radio range
-
range of application
-
range of audibility
-
range of definition
-
range of motion
-
range of products
-
range of sea level
-
range of sensitivity
-
range of stability
-
range of stress
-
range of warp knitting machine
-
rated frequency range
-
reception range
-
recording range
-
red range of temperature gage
-
reduction range
-
reference range
-
refrigeration range
-
regulating range
-
resistance range
-
rolled-products range
-
runway visual range
-
saturation range
-
scale range
-
screen range
-
seam-height range
-
setting range
-
shooting range
-
shore range
-
single-phase preboiling range
-
sintering range
-
slant range
-
slant visual range
-
source range
-
spectral range
-
spectral sensitivity range
-
speed range
-
stability range
-
steaming range
-
still-air flight range
-
strain-hardening range
-
stress range
-
suppressed-zero range
-
surface range
-
synchronization range
-
tapping range
-
target range
-
temperature range
-
thermocline range
-
tidal range
-
tolerance range
-
tonal range
-
tool offset range
-
torque conversion range
-
total range
-
tracking range
-
traffic range
-
transfer gears range
-
transmission range
-
travel range
-
trial range
-
tuning range
-
turn-off range
-
type size range
-
unambiguous range
-
variable range
-
vat pigment pad stream range
-
visibility range
-
visual range
-
vitrification range
-
volatility range
-
voltage range
-
volume range
-
wool scouring range
-
work-hardening range
-
working range
-
zoom range -
35 control
1) управление; регулирование || управлять; регулировать2) контроль || контролировать3) управляющее устройство; устройство управления; регулятор4) профессиональное мастерство, квалификация, техническая квалификация5) pl органы управления•"in control" — "в поле допуска" ( о результатах измерения)
to control closed loop — управлять в замкнутой системе; регулировать в замкнутой системе
- 2-handed controlsto control open loop — управлять в разомкнутой системе; регулировать в разомкнутой системе
- 32-bit CPU control
- acceptance control
- access control
- acknowledge control
- active process control
- adaptable control
- adaptive constraint control
- adaptive control for optimization
- adaptive control
- adaptive feed rate control
- adaptive quality control
- adjustable feed control
- adjustable rotary control
- adjustable speed control
- adjusting control
- adjustment control
- AI control
- air logic control
- analog data distribution and control
- analogical control
- analytical control
- application control
- arrows-on-curves control
- autodepth control
- autofeed control
- automated control of a document management system
- automated technical control
- automatic backlash control
- automatic control
- automatic editing control
- automatic gain control
- automatic gripper control
- automatic level control
- automatic process closed loop control
- automatic remote control
- automatic sensitivity control
- automatic sequence control
- automatic speed control
- automatic stability controls
- auxiliaries control
- balanced controls
- band width control
- bang-bang control
- bang-bang-off control
- basic CNC control
- batch control
- bibliographic control
- bin level control
- boost control
- built-in control
- button control
- cam control
- cam throttle control
- camshaft control
- carriage control
- Cartesian path control
- Cartesian space control
- cascade control
- C-axis spindle control
- cell control
- center control
- central control
- central supervisory control
- centralized control
- centralized electronic control
- central-station control
- changeover control
- chip control
- circumferential register control
- close control
- closed cycle control
- closed loop control
- closed loop machine control
- closed loop manual control
- closed loop numerical control
- closed loop position control
- clutch control
- CNC control
- CNC indexer control
- CNC programmable control
- CNC symbolic conversational control
- CNC/CRT control
- CNC/MDI control
- coarse control
- coded current control
- coded current remote control
- color control
- combination control
- command-line control
- compensatory control
- composition control
- compound control
- computed-current control
- computed-torque control
- computer control
- computer numerical control
- computer process control
- computer-aided measurement and control
- computer-integrated manufacturing control
- computerized control
- computerized numerical control
- computerized process control
- constant surface speed control
- constant value control
- contactless control
- contact-sensing control
- contamination control
- continuous control
- continuous path control
- continuous process control
- contour profile control
- contouring control
- conventional hardware control
- conventional numerical control
- conventional tape control
- convergent control
- conversational control
- conversational MDI control
- coordinate positioning control
- coordinate programmable control
- copymill control
- counter control
- crossed controls
- current control
- cycle control
- dash control
- data link control
- data storage control
- deadman's handle controls
- depth control
- derivative control
- dial-in control
- differential control
- differential gaging control
- differential gain control
- differential temperature control
- digital brushless servo control
- digital control
- digital position control
- digital readout controls
- dimensional control
- direct computer control
- direct control
- direct digital control
- direct numerical control
- direction control
- directional control
- dirt control
- discontinuous control
- discrete control
- discrete event control
- discrete logic controls
- dispatching control
- displacement control
- distance control
- distant control
- distributed control
- distributed numerical control
- distributed zone control
- distribution control
- dog control
- drum control
- dual control
- dual-mode control
- duplex control
- dust control
- dynamic control
- eccentric control
- edge position control
- EDP control
- electrical control
- electrofluidic control
- electromagnetic control
- electronic control
- electronic level control
- electronic speed control
- electronic swivel control
- elevating control
- emergency control
- end-point control
- engineering change control
- engineering control
- entity control
- environmental control
- error control
- error plus error-rate control
- error-free control
- external beam control
- factory-floor control
- false control
- feed control
- feed drive controls
- feedback control
- feed-forward control
- field control
- fine control
- finger-tip control
- firm-wired numerical control
- fixed control
- fixed-feature control
- fixture-and-tool control
- flexible-body control
- floating control
- flow control
- fluid flow control
- follow-up control
- foot pedal control
- force adaptive control
- forecasting compensatory control
- fork control
- four quadrant control
- freely programmable CNC control
- frequency control
- FROG control
- full computer control
- full order control
- full spindle control
- gage measurement control
- gain control
- ganged control
- gap control
- gear control
- generative numerical control
- generic path control
- geometric adaptive control
- graphic numerical control
- group control
- grouped control
- guidance control
- hairbreath control
- hand control
- hand feed control
- hand wheel control
- hand-held controls
- handle-type control
- hand-operated controls
- hardened computer control
- hardwared control
- hardwared numerical control
- heating control
- heterarchical control
- hierarchical control
- high-integrity control
- high-level robot control
- high-low control
- high-low level control
- high-technology control
- horizontal directional control
- humidity control
- hybrid control
- hydraulic control
- I/O control
- immediate postprocess control
- inching control
- in-cycle control
- independent control
- indexer control
- indirect control
- individual control
- industrial processing control
- industrial-style controls
- infinite control
- infinite speed control
- in-process control
- in-process size control
- in-process size diameters control
- input/output control
- integral CNC control
- integral control
- integrated control
- intelligent control
- interacting control
- interconnected controls
- interlinking control
- inventory control
- job control
- jogging control
- joint control
- joystick control
- just-in-time control
- language-based control
- laser health hazards control
- latching control
- lead control
- learning control
- lever control
- lever-operated control
- line motion control
- linear control
- linear path control
- linearity control
- load control
- load-frequency control
- local control
- local-area control
- logic control
- lubricating oil level control
- machine control
- machine programming control
- machine shop control
- macro control
- magnetic control
- magnetic tape control
- main computer control
- malfunction control
- management control
- manual control
- manual data input control
- manual stop control
- manually actuatable controls
- manufacturing change control
- manufacturing control
- master control
- material flow control
- MDI control
- measured response control
- mechanical control
- memory NC control
- memory-type control
- metering control
- metrological control of production field
- microbased control
- microcomputer CNC control
- microcomputer numerical control
- microcomputer-based sequence control
- microprocessor control
- microprocessor numerical control
- microprogrammed control
- microprogramming control
- milling control
- model reference adaptive control
- model-based control
- moisture control
- motion control
- motor control
- motor speed control
- mouse-driven control
- movable control
- multicircuit control
- multidiameter control
- multilevel control
- multimachine tool control
- multiple control
- multiple-processor control
- multiposition control
- multistep control
- multivariable control
- narrow-band proportional control
- navigation control
- NC control
- neural network adaptive control
- noise control
- noncorresponding control
- noninteracting control
- noninterfacing control
- nonreversable control
- nonsimultaneous control
- numerical contouring control
- numerical control
- numerical program control
- odd control
- off-line control
- oligarchical control
- on-board control
- one-axis point-to-point control
- one-dimensional point-to-point control
- on-line control
- on-off control
- open loop control
- open loop manual control
- open loop numerical control
- open-architecture control
- operating control
- operational control
- operator control
- optical pattern tracing control
- optimal control
- optimalizing control
- optimizing control
- oral numerical control
- organoleptic control
- overall control
- overheat control
- override control
- p. b. control
- palm control
- parameter adaptive control
- parameter adjustment control
- partial d.o.f. control
- path control
- pattern control
- pattern tracing control
- PC control
- PC-based control
- peg board control
- pendant control
- pendant-actuated control
- pendant-mounted control
- performance control
- photoelectric control
- physical alignment control
- PIC control
- PID control
- plugboard control
- plug-in control
- pneumatic control
- point-to-point control
- pose-to-pose control
- position/contouring numerical control
- position/force control
- positional control
- positioning control
- positive control
- postprocess quality control
- power adaptive control
- power control
- power feed control
- power-assisted control
- powered control
- power-operated control
- precision control
- predictor control
- preselective control
- preset control
- presetting control
- pressbutton control
- pressure control
- preview control
- process control
- process quality control
- production activity control
- production control
- production result control
- programmable adaptive control
- programmable cam control
- programmable control
- programmable logic adaptive control
- programmable logic control
- programmable machine control
- programmable microprocessor control
- programmable numerical control
- programmable sequence control
- proportional plus derivative control
- proportional plus floating control
- proportional plus integral control
- prototype control
- pulse control
- pulse duration control
- punched-tape control
- purpose-built control
- pushbutton control
- quality control
- radio remote control
- radium control
- rail-elevating control
- ram stroke control
- ram-positioning control
- rapid-traverse controls for the heads
- rate control
- ratio control
- reactive control
- real-time control
- reduced-order control
- register control
- registration control
- relay control
- relay-contactor control
- remote control
- remote program control
- remote switching control
- remote valve control
- remote-dispatch control
- resistance control
- resolved motion rate control
- retarded control
- reversal control
- revolution control
- rigid-body control
- robot control
- robot perimeter control
- robot teach control
- rod control
- safety control
- sampled-data control
- sampling control
- schedule control
- SCR's control
- second derivative control
- selective control
- selectivity control
- self-acting control
- self-adaptive control
- self-adjusting control
- self-aligning control
- self-operated control
- self-optimizing control
- self-programming microprocessor control
- semi-automatic control
- sensitivity control
- sensor-based control
- sequence control
- sequence-type control
- sequential control
- series-parallel control
- servo control
- servo speed control
- servomotor control
- servo-operated control
- set value control
- shaft speed control
- shape control
- shift control
- shop control
- shower and high-pressure oil temperature control
- shut off control
- sight control
- sign control
- single variable control
- single-flank control
- single-lever control
- size control
- slide control
- smooth control
- software-based NC control
- softwared numerical control
- solid-state logic control
- space-follow-up control
- speed control
- stabilizing control
- stable control
- standalone control
- start controls
- static control
- station control
- statistical quality control
- steering control
- step-by-step control
- stepless control
- stepped control
- stick control
- stock control
- stop controls
- stop-point control
- storage assignment control
- straight cut control
- straight line control
- stroke control
- stroke length control
- supervisor production control
- supervisory control
- swarf control
- switch control
- symbolic control
- synchronous data link control
- table control
- tap-depth controls
- tape control
- tape loop control
- teach controls
- temperature control
- temperature-humidity air control
- template control
- tension control
- test control
- thermal control
- thermostatic control
- three-axis contouring control
- three-axis point-to-point control
- three-axis tape control
- three-mode control
- three-position control
- throttle control
- thumbwheel control
- time control
- time cycle control
- time optimal control
- time variable control
- time-critical control
- time-proportional control
- timing control
- token-passing access control
- tool life control
- tool run-time control
- torque control
- total quality control
- touch-panel NC control
- touch-screen control
- tracer control
- tracer numerical control
- trajectory control
- triac control
- trip-dog control
- TRS/rate control
- tuning control
- turnstile control
- two-axis contouring control
- two-axis point-to-point control
- two-dimension control
- two-hand controls
- two-position control
- two-position differential gap control
- two-step control
- undamped control
- user-adjustable override controls
- user-programmable NC control
- variable flow control
- variable speed control
- variety control
- varying voltage control
- velocity-based look-ahead control
- vise control
- vision responsive control
- visual control
- vocabulary control
- vocal CNC control
- vocal numerical control
- voltage control
- warehouse control
- washdown control
- water-supply control
- welding control
- wheel control
- wide-band control
- zero set control
- zoned track controlEnglish-Russian dictionary of mechanical engineering and automation > control
-
36 circuit
2) канал3) т. граф. простая цепь, контур•- active circuit
- acyclic circuit
- adding circuit
- add circuit
- addressing circuit
- advancing circuit
- alarm circuit
- amplifying circuit
- analogous circuit
- analog circuit
- AND-to-OR circuit
- antialiasing circuit
- anticoincidence circuit
- antihunting circuit
- antihunt circuit
- aperiodic circuit
- arithmetic circuit
- arithmetical circuit
- astable circuit
- averaging circuit
- balanced circuit
- basis circuit
- beam-lead integrated circuit
- benchmark circuit
- binary-valued digital circuit
- binary-valued circuit
- bipolar circuit
- bistable circuit
- blanking circuit
- bleeder circuit
- bridge circuit
- buffer circuit
- carry circuit
- character selection circuit
- checking circuit
- check circuit
- clamping circuit
- clocked circuit
- clock-recovery circuit
- closed circuit
- code disjoint circuit
- coincidence circuit
- combinational circuit
- combinatorial circuit
- communication circuit
- comparator circuit
- compare circuit
- comparison circuit
- complementary circuit
- complementary integrated circuit
- complementary transistor logic circuit
- complex function circuit
- computer circuit
- computer test circuit
- computing circuit
- control circuit
- core-diode circuit
- core-transistor circuit
- correcting circuit
- correction circuit
- counter circuit
- counting circuit
- coupling circuit
- current-limit circuit
- current-operated circuit
- current-summation circuit
- custom product integrated circuit
- custom integrated circuit
- custom-wired integrated circuit
- cutoff circuit
- cycle circuit
- cyclic circuit
- dead-on-arrival integrated circuit
- decode circuit
- decoding circuit
- deenergizing circuit
- deflection circuit
- delay circuit
- densely packed circuit
- differentiating circuit
- digital computing circuit
- diode circuit
- diode-coupled circuit
- diode-transistor logic circuit
- direct-coupled circuit
- direct-coupled transistor logic circuit
- direct-current circuit
- discrete component circuit
- discrete logic-level
- discrete wired circuit
- display circuit
- divide-by-two circuit
- dividing circuit
- double-sided printed circuit
- doubling circuit
- drive circuit
- dry circuit
- dual circuit
- duplex circuit
- Eccles-Jordan circuit
- edge-activated circuit
- emitter-coupled circuit
- emitter-coupled logic circuit
- emitter-emitter-coupled logic circuit
- equality circuit
- equivalent circuit
- etched circuit
- Euler circuit
- except circuit
- fanout-free circuit
- fast-switching circuit
- fault detection circuit
- fault-free circuit
- fault-secure circuit
- faulty circuit
- feedback circuit
- ferrite-diode circuit
- ferrite-transistor circuit
- ferroresonant computing circuit
- film integrated circuit
- flag-testing circuit
- flat-pack integrated circuit
- flexible printed circuit
- flexible circuit
- flip-chip integrated circuit
- flip-flop circuit
- frame-grounding circuit
- frequency-halving circuit
- function circuit
- gate circuit
- Goto-pair circuit
- half-duplex circuit
- halving circuit
- Hamilton circuit
- hand-designed circuit
- hardwired circuit
- high-speed circuit
- high-threshold logic circuit
- holding circuit
- hybrid circuit
- idler circuit
- imbedded circuit
- IMOS circuit
- impulse circuit
- inhibit circuit
- input circuit
- integrated circuit
- integrating circuit
- integro-differential circuit
- interchange circuit
- interface circuit
- interfacing circuit
- interlock circuit
- invert circuit
- ion-implanted MOS circuit
- irredundant circuit
- Josephson integrated circuit
- junction transistor circuit
- ladder circuit
- lag-lead circuit
- laminar circuit
- large arithmetic circuit
- large-scale integrated circuit
- large-scale integration circuit
- latch circuit
- lead-lag circuit
- leased circuit
- level circuit
- linear circuit
- linear integrated circuit
- linearity circuit
- liquid logic circuit
- load circuit
- locked pair circuit
- locking circuit
- logic circuit
- logical circuit
- low-threshold integrated circuit
- LSI circuit
- lumped circuit
- magnetic circuit
- magnetic-core circuit
- majority circuit
- match circuit
- material equivalence circuit
- matrix circuit
- maximum-remembering circuit
- measuring circuit
- medium-scale integration circuit
- memory circuit
- memory-decoder circuit
- message circuit
- metal-oxide-semiconductor circuit
- microamp circuit
- microelectronic integrated circuit
- microminiature circuit
- microwave circuit
- mil spec integrated circuit
- milliwatt circuit
- miniature circuit
- minimum-remembering circuit
- mixed-level circuit
- mixing circuit
- modularized circuit
- molecular integrated circuit
- monitoring circuit
- monolithic integrated circuit
- monostable circuit
- MOS circuit
- MOS integrated circuit
- MOS LSI circuit
- MSI circuit
- multichip integrated circuit
- multifunction integrated circuit
- multilayer circuit
- multilevel circuit
- multiple output circuit
- multiplying circuit
- multipoint circuit
- multistable circuit
- multistage circuit
- nanosecond circuit
- n-channel circuit
- network circuit
- noise-balancing circuit
- noncoincidence circuit
- noncutoff circuit
- non-self-checking circuit
- one-core-per-bit circuit
- one-generator equivalent circuit
- one-out-of-four selecting circuit
- one-shot circuit
- open circuit
- optical commutation circuit
- optical memory circuit
- optically coupled circuit
- optoelectronic circuit
- output circuit
- packaged circuit
- packed circuit
- p-channel circuit
- phantom circuit
- phase-comparison circuit
- phase-inverting circuit
- picosecond circuit
- pilot circuit
- plastic-embedded circuit
- point-to-point circuit
- power circuit
- power monitoring circuit
- power-fail circuit
- printed circuit
- priority circuit
- propagation circuit
- protection circuit
- pulse circuit
- pulse-actuated circuit
- pulse-broadening circuit
- pulse-regenerating circuit
- pulse-shaping circuit
- pulse-stretching circuit
- pulse-switching circuit
- pumped tunnel-diode transistor logic circuit
- pumping circuit
- quenching circuit
- race-free circuit
- radio-frequency circuit
- random-logic circuit
- ratioed circuit
- reading circuit
- received-data circuit
- receiving circuit
- reconfigurable integrated circuit
- redundant circuit
- reference circuit
- refreshing circuit
- relaxation circuit
- reset circuit
- retriggerable circuit
- rewriting circuit
- ring circuit
- rounding circuit
- sample-hold circuit
- saturated circuit
- scale-of-N circuit
- scale-of-two circuit
- scaling circuit
- schematic circuit
- Schmitt trigger circuit
- Schmitt circuit
- screen printed circuit
- selection circuit
- select circuit
- self-checking circuit
- self-testing circuit
- self-timed circuit
- semiconductor circuit
- send-request circuit
- sequential circuit
- shifting circuit
- shift circuit
- short circuit
- shunt-peaking circuit
- sign-controlled circuit
- silicon integrated circuit
- silicon-on-sapphire integrated circuit
- simplex circuit
- single-chip circuit
- single-ended circuit
- single-level circuit
- single-phase circuit
- single-shot circuit
- small-scale integration circuit
- solid-state circuit
- solid circuit
- SOS integrated circuit
- squaring circuit
- SSI circuit
- stabilizing circuit
- stamped circuit
- start-stop circuit
- steering circuit
- storage circuit
- storage-selection circuit
- strongly fault-secure circuit
- subtraction circuit
- summing circuit
- sweep circuit
- switching circuit
- symbolic circuit
- synchronizing circuit
- synthesis circuit
- thick-film circuit
- thin-film circuit
- threshold circuit
- time-anticoincidence circuit
- time-base circuit
- time-coincidence circuit
- time-delay circuit
- toll circuit
- totally self-checking circuit
- transistor circuit
- transistor-core circuit
- transistor-resistor circuit
- transistor-transistor-logic circuit
- translation circuit
- transmitted-data circuit
- transmitting circuit
- tree circuit
- trigger -action circuit
- trigger circuit
- trunk circuit
- tunnel diode circuit
- twin-tunnel-diode circuit
- twin circuit
- two-cores-per-bit circuit
- two-input circuit
- two-level circuit
- two-way circuit
- ultra-large-scale integration circuit
- unidirectional circuit
- unpackaged circuit
- unpacked circuit
- very-high-speed integrated circuit
- very-large-scale integration circuit
- virtual circuit
- VLSI circuit
- voice circuit
- voice-grade circuit
- voltage-control circuit
- voltage-doubling circuit
- voltage-multiplying circuit
- voltage-summation circuit
- voter circuit
- wave-shaping circuit
- whole-wafer circuit
- wired AND circuit
- wired OR circuit
- wire-wrapped circuit
- writing circuit
- zero circuitEnglish-Russian dictionary of computer science and programming > circuit
-
37 instruction
2) инструкция; программа действий3) обучение•- accumulator shift instruction
- actual instruction
- address modification instruction
- addressless instruction
- alphanumeric instruction
- alphameric instruction
- arithmetical instruction
- arithmetic instruction
- assignment instruction
- autocode instruction
- autoindexed instruction
- basic instruction
- bit-manipulation instruction
- blank instruction
- block-move instruction
- branching instruction
- branch instruction
- branching-programmed instruction
- branch-on-zero instruction
- breakpoint instruction
- broadcast instruction
- byte instruction
- call instruction
- card read instruction
- character-oriented instruction
- clear and add instruction
- clear store instruction
- clearing instruction
- compare instruction
- comparison instruction
- complete instruction
- compound instruction
- computer instruction
- computer-aided instruction
- computer-assisted instruction
- conditional assembly instruction
- conditional branch instruction
- conditional breakpoint instruction
- conditional instruction
- conditional jump instruction
- conditional stop instruction
- conditional transfer instruction
- conflicting instructions
- constant instruction
- consumer instruction
- control instruction
- control transfer instruction
- convert instruction
- current instruction
- data movement instruction
- data transfer instruction
- decimal instruction
- decision instruction
- declarative instruction
- decoded instruction
- diagnose instruction
- direct access instruction
- direct instruction
- discarded instruction
- discrimination instruction
- display instruction
- do-nothing instruction
- double-precision instruction
- dual-issued instructions
- dummy instruction
- edit instruction
- effective instruction
- engineering instruction
- entry instruction
- exchange instruction
- executive instruction
- external devices instruction
- extracode instruction
- extract instruction
- floating-point instruction
- follow the instructions carefully
- format instruction
- four-address instruction
- full-word instruction
- general instruction
- half-word instruction
- halt instruction
- housekeeping instruction
- idle instruction
- ignore instruction
- illegal instruction
- immediate address instruction
- immediate instruction
- imperative instruction
- indirect instruction
- input/output instruction
- inquiry input/output instruction
- integer instruction
- internal manipulation instruction
- interpretive instruction
- interrupt instruction
- interruptable instruction
- invitation instruction
- invite instruction
- iterative instruction
- jump instruction
- jump to subroutine instruction
- keyboard instruction
- linear programmed instruction
- link instruction
- linkage macro instruction
- load index register instruction
- load repeat counter instruction
- logical instruction
- logic instruction
- look-up instruction
- machine code instruction
- machine instruction
- machine language instruction
- macro instruction
- macroexpansion instruction
- macroprocessing instruction
- maintenance instruction
- math instruction
- memory load instruction
- memory protect privileged instruction
- memory-reference instruction
- micro instruction
- microprogrammable instruction
- mnemonic instruction
- modified instruction
- monadic instruction
- monitor call instruction
- motion video instruction
- move instruction
- MQ register sign jump instruction
- MQ sign jump instruction
- multiaddress instruction
- multilplying instruction
- multiple-address instruction
- multiple instruction
- multiple-cycle instruction
- multiple-length instruction
- multiplier-quotient register sign jump instruction
- multiplier-quotient sign jump instruction
- multiply-accumulate instruction
- N-address instruction
- native instruction
- noaddress instruction
- nonmemory-reference instruction
- nonprint instruction
- nonprivileged instruction
- non-speculative instruction
- no-op instruction
- no-operation instruction
- normalized instruction
- normalize instruction
- N-plus-one address instruction
- null instruction
- object instruction
- on-chip instruction
- one-address instruction
- one-and-a-half-address instruction
- one-over-one address instruction
- one-plus-one address instruction
- on-screen instruction
- operational-address instruction
- operation-address instruction
- optional halt instruction
- optional pause instruction
- optional stop instruction
- organizational instruction
- overflow jump instruction
- overriding instruction
- pause instruction
- picture-description instruction
- preempted instruction
- presumptive instruction
- prewired instruction
- privileged instruction
- producer instruction
- programmed instruction
- propagation instruction
- pseudo instruction
- quadruple address instruction
- quasi instruction
- reading instruction
- read instruction
- red-tape instruction
- reference instruction
- register-to-register instruction
- relative instruction
- repeat instruction
- repetition instruction
- restart instruction
- return instruction
- right shift instruction
- rotate instruction
- roundoff instruction
- scalar instruction
- search instruction
- seek instruction
- shift instruction
- shift-jump instruction
- short instruction
- single-address instruction
- single-cycle instruction
- single-operand instruction
- skeleton instruction
- skip instruction
- source-designation instruction
- source-destination instruction
- stack instruction
- steering instruction
- stop instruction
- string instruction
- summarize instruction
- supervisor call instruction
- symbolic instruction
- table look-up instruction
- tape instruction
- text-entry instruction
- three-address instruction
- three-plus-one-address instruction
- transfer instruction
- transfer of control instruction
- trap instruction
- try instruction
- two-address instruction
- two-plus-one-address instruction
- unconditional branch instruction
- unconditional control transfer instruction
- unconditional jump instruction
- unconditional transfer instruction
- unmodified instruction
- unretired instruction
- variable instruction
- variable length instruction
- variable-cycle instruction
- vector-processing instruction
- vector instruction
- verbal instruction
- waste instruction
- write instruction
- zero-address instruction
- zeroing instruction
- zero-suppress instructionEnglish-Russian dictionary of computer science and programming > instruction
-
38 buffer
1) буферное устройство, буферное ЗУ•- frame buffer
- incoming buffer
- input/output buffer
- outgoing buffer
- parallel buffer
- receiver buffer
- screen image buffer
- sender buffer
- STD-input buffer
- variable-length buffer
- video buffer
- write bufferEnglish-Russian dictionary of telecommunications and their abbreviations > buffer
-
39 data-in mode
-
40 display mode
режим визуального отображения; режим работы с выводом на дисплей
См. также в других словарях:
Screen scraping — is a technique in which a computer program extracts data from the display output of another program. The program doing the scraping is called a screen scraper. The key element that distinguishes screen scraping from regular parsing is that the… … Wikipedia
Input device — In computing, an input device is any peripheral (piece of computer hardware equipment) used to provide data and control signals to an information processing system such as a computer or other information appliance. Input and output devices make… … Wikipedia
Screen reader — A screen reader is a software application that attempts to identify and interpret what is being displayed on the screen (or, more accurately, sent to standard output, whether a video monitor is present or not). This interpretation is then re… … Wikipedia
Screen — Contents 1 Separation or partitioning 2 Filtration/selection processes 3 Media display … Wikipedia
screen saver — noun (computer science) a moving design that appears on a computer screen when there has been no input for a specified period of time screen savers prevent the damage that occurs when the same areas of light and dark are displayed too long •… … Useful english dictionary
Soft Input Panel — The Soft Input Panel (also called SIP) is a special on screen input method for devices which do not have standard keyboards. SIP is commonly used in PocketPC and Tablet PC devices, where there is no room for keyboard. In Windows there is a… … Wikipedia
System/34 and System/36 Screen Design Aid — Screen Design Aid (System/34 and System/36) (SDA) is a utility for the IBM System/34, System/36, System/38, and AS/400 (iSeries) midrange computers.This article refers to the S/34 and S/36 implementations of SDA. S/38 and AS/400 use a different… … Wikipedia
touch screen — screen used as an input device by identifying the place on a screen that has been touched … English contemporary dictionary
Tablet PC Input Panel — A component of Microsoft Windows Details Included with Windows XP Tablet PC Edition, Windows Vista and onwards The Tablet PC Input Panel is an accessory included in Microsoft Windows that allows input of text using a pen and digitizing tablet,… … Wikipedia
Delimiterless input — is a special feature of some mini and all micro computers in which the computer can recognize and act upon a single character or keypress without requiring use of a transmit or send key. Older mini and mainframe computers generally operated on a… … Wikipedia
Unicode input — Many systems provide direct Unicode input support in some form to allow selection of arbitrary Unicode characters. Selection from a screen Many systems provide a way to select Unicode characters visually. ISO 14755 refers to this as a screen… … Wikipedia