-
1 unabhängig verzögerter Überstromauslöser
Максимальное реле или максимальный расцепитель тока с независимой выдержкой времени
Максимальное реле или максимальный расцепитель тока, срабатывающие с определенной выдержкой времени, которая может регулироваться, но не зависит от величины сверхтока.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
definite time-delay over-current release
an over-current release which operates with a definite time-delay, which may be adjustable, but is independent of the value of the over-current
[IEV number 441-16-34]FR
déclencheur à maximum de courant à retard indépendant
déclencheur à maximum de courant qui fonctionne avec un retard défini qui peut être réglable mais est indépendant de la valeur de la surintensité.
[IEV number 441-16-34]Параллельные тексты EN-RU Protection against overload may be provided on both the high-voltage side and the low-voltage side, depending on the transformer power. For low-power transformers the protection should be positioned on the low-voltage side, while for high-power transformers the protection should be provided on the high-voltage side. Protection against overloads on the HV side is provided using HV circuit breakers associated with maximum-current protections in constant time or independent time.
[Legrand]В зависимости от мощности трансформатора, защита от перегрузки выполняется на стороне высшего или низшего напряжения. Мощные трансформаторы защищают со стороны электросети, а маломощные – со стороны нагрузки. Защита от перегрузки на стороне высшего напряжения осуществляется высоковольтным автоматическим выключателем с максимальными расцепителями тока с независимой выдержкой времени.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
- реле электрическое
Классификация
>>>EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > unabhängig verzögerter Überstromauslöser
-
2 Grenzstrom(stärke) (eines Zählers)
1
максимальный ток
наибольшее значение тока, при котором счетчик удовлетворяет требованиям настоящего стандарта в отношении точности.
[ ГОСТ 6570-96]2
максимальный ток
-
[IEV number 314-07-03]EN
maximum current
highest value of current at which a meter meets the specified accuracy requirements
[IEV number 314-07-03]FR
courant maximal
valeur la plus grande pour laquelle un compteur est censé satisfaire aux prescriptions d’exactitude spécifiées
[IEV number 314-07-03]Тематики
EN
DE
FR
- courant maximal valeur la plus grande pour laquelle un compteur est censé satisfaire aux prescriptions d’exactitude spécifiées [IEV number 314-07-03]
Немецко-русский словарь нормативно-технической терминологии > Grenzstrom(stärke) (eines Zählers)
-
3 Kurzschlussstrom (einer Zelle oder Batterie), m
ток короткого замыкания химического источника тока
ток короткого замыкания
Максимальное значение тока разряда химического источника тока при коротком замыкании внешней цепи.
[ ГОСТ 15596-82]
ток короткого замыкания
Максимальный ток, отдаваемый батареей в цепь с минимальным сопротивлением по сравнению с сопротивлением батареи в заданных условиях.
[Инструкция по эксплуатации стационарных свинцово-кислотных аккумуляторных батарей в составе ЭПУ на объектах ВСС России. Москва 1998 г.]EN
short-circuit current (related to cells or batteries)
maximum current which should be delivered by a cell or battery into an external circuit with zero electric resistance, or an external circuit which depresses the cell or battery voltage to approximately zero volt
NOTE – Zero electric resistance is a hypothetical condition and in practice the short-circuit current is the peak current flowing in a circuit of very low resistance compared to the internal resistance of the battery.
[IEV number 482-03-26 ]FR
courant de court-circuit (d’un élément ou d’une batterie), m
courant maximal que pourrait fournir un élément ou une batterie dans un circuit extérieur de résistance électrique nulle, ou un circuit extérieur qui abaisse la tension aux bornes de l’élément ou de la batterie approximativement à zéro volt
NOTE – Une résistance électrique nulle est hypothétique et en pratique, le courant de court-circuit est le courant de crête circulant à travers un circuit de résistance très faible par rapport à la résistance interne de la batterie.
[IEV number 482-03-26 ]Тематики
Классификация
>>>Синонимы
EN
DE
- Kurzschlussstrom (einer Zelle oder Batterie), m
FR
- Kurzschlussstrom (einer Zelle oder Batterie), m
Немецко-русский словарь нормативно-технической терминологии > Kurzschlussstrom (einer Zelle oder Batterie), m
-
4 Zählertyp
1
тип счетчика
термин, используемый для определения совокупности конкретной конструкции счетчика, имеющей:
а) сходные метрологические характеристики;
б) конструктивное подобие элементов, определяющих эти характеристики.
Тип может иметь несколько значений номинального тока и номинального напряжения.
Счетчики обозначаются изготовителем одной или большим числом групп букв или цифр, или комбинацией букв и цифр. Каждый тип имеет только одно обозначение.
Примечание - Данный тип представляют один или несколько образцов счетчиков, предназначенных для проведения испытаний для целей утверждения типа, характеристики которых (номинальные токи и номинальные напряжения) соответствуют значениям, указанным изготовителем.
[ ГОСТ 6570-96]2
тип счетчика
-
[IEV number 314-07-07]EN
meter type
particular design of meter, manufactured by one manufacturer, having:
a) similar metrological properties;
b) the same uniform construction of parts determining these properties;
c) the same ratio of the maximum current to the reference current
NOTE 1 – The type may have several values of reference current and reference voltage.
NOTE 2 – Meters are designated by the manufacturer by one or more groups of letters or numbers, or a combination of letters and numbers. Each type has one designation only.
NOTE 3 – The type is represented by the sample meter(s) intended for the type tests and whose characteristics (reference current and reference voltage) are chosen from the values given in the tables proposed by the manufacturer.
[IEV number 314-07-07]FR
type
ensemble des compteurs fabriqués par un même constructeur et ayant:
a) des qualités métrologiques similaires;
b) l’uniformité constructive des constituants déterminant ces qualités;
c) un même rapport entre courant maximal et courant de référence
NOTE 1 – Le type peut comporter différentes valeurs de courant de référence et de tension de référence.
NOTE 2 – Les compteurs sont désignés par le constructeur, par une ou plusieurs associations soit de lettres, soit de chiffres. A chaque type correspond une seule désignation.
NOTE 3 – Le type est représenté par le ou les compteurs échantillons destinés aux essais de type et dont les caractéristiques (courant de référence et tension de référence) sont choisies parmi celles figurant dans les tableaux proposés par le constructeur.
[IEV number 314-07-07]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Zählertyp
-
5 Übernahmestrom
ток координации
Токовая координата точки пересечения время-токовых характеристик двух устройств для защиты от сверхтоков.
МЭК 60050(441-17-16).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
ток координации (Iв)
Координата точки пересечения время-токовых характеристик наибольшей отключающей способности двух аппаратов защиты от сверхтоков.
Примечания
1 Ток координации — предельное значение тока, выше которого при наличии двух последовательно соединенных аппаратов защиты от сверхтоков защитный аппарат, расположенный со стороны питания, как правило, но не обязательно обеспечивает резервную защиту второго защитного аппарата
2 Вместо время-токовых характеристик можно использовать характеристики I2t
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
take-over current
the current co-ordinate of the intersection between the time-current characteristics of two over-current protective devices
[IEV number 441-17-16]FR
courant d'intersection
valeur du courant correspondant à l'intersection des caractéristiques temps-courant de deux dispositifs de protection à maximum de courant
[IEV number 441-17-16]Тематики
EN
DE
FR
ток пересечения
-
[IEV number 442-05-61]EN
take-over current
the current co-ordinate of the intersection between the maximum break time-current characteristics of two overcurrent protective devices
Source: 441-17-16 MOD
[IEV number 442-05-61]FR
courant d'intersection
coordonnées du courant de l'intersection entre les caractéristiques de durée maximale de coupure temps-courant de deux dispositifs de protection à maximum de courant
Source: 441-17-16 MOD
[IEV number 442-05-61]Тематики
- электротехника, основные понятия
EN
DE
FR
ток пересечения IB
-
[IEV number 442-05-61]EN
take-over current
the current co-ordinate of the intersection between the maximum break time-current characteristics of two overcurrent protective devices
[IEV number 442-05-61]FR
courant d'intersection
coordonnées du courant de l'intersection entre les caractéristiques de durée maximale de coupure temps-courant de deux dispositifs de protection à maximum de courant
[IEV number 442-05-61]Тематики
Синонимы
- IB
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Übernahmestrom
-
6 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
7 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
8 Überstromselektivität
селективность по сверхтокам
Координация рабочих характеристик двух или нескольких устройств для защиты от сверхтоков с таким расчетом, чтобы в случае возникновения сверхтоков в пределах указанного диапазона срабатывало только устройство, предназначенное для оперирования в данном диапазоне, а прочие не срабатывали.
Примечание. Различаются последовательная селективность, когда через различные устройства для защиты от сверхтоков проходит практически одинаковый сверхток, и параллельная селективность, когда через тождественные защитные устройства проходят различные доли сверхтока.
МЭК 60050(441-17-15).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
селективность при сверхтоке
Координация соответствующих характеристик двух или более устройств для защиты от сверхтоков с таким расчетом, чтобы при появлении сверхтоков в установленных пределах срабатывало устройство, рассчитанное на эти пределы, в то время как другое (ие) устройство (а) не срабатывало (и).
[ ГОСТ Р 50339. 0-2003 ( МЭК 60269-1-98)]
селективность при сверхтоке предохранителей
Координация соответствующих характеристик двух или нескольких предохранителей, или предохранителей и других защитных устройств, обеспечивающая при появлении сверхтоков, находящихся в данных пределах, состояние срабатывания предохранителя, предусмотренного для срабатывания в этих пределах, тогда как другие предохранители не срабатывают.
[ ГОСТ 17242-86]EN
over-current discrimination
co-ordination of the operating characteristics of two or more over-current protective devices such that, on the incidence of over-currents within stated limits, the device intended to operate within these limits does so, while the other(s) does (do) not
NOTE Distinction is made between series discrimination involving different over-current protective devices passing substantially the same over-current and network discrimination involving identical protective devices passing different proportions of the over-current.
[IEV 441-17-15]FR
sélectivité lors d'une surintensité
coordination entre les caractéristiques de fonctionnement de plusieurs dispositifs de protection à maximum de courant de telle façon qu'à l'apparition de surintensités comprises dans des limites données, le dispositif prévu pour fonctionner entre ces limites fonctionne, tandis que le ou les autres ne fonctionnent pas
NOTE On distingue la sélectivité série réalisée par différents dispositifs de protection à maximum de courant soumis pratiquement à la même surintensité et la sélectivité de réseau réalisée par des dispositifs de protection à maximum de courant identiques soumis à des fractions différentes de la surintensité
[IEV 441-17-15]Параллельные тексты EN-RU
Discrimination Method
Appropriate when downstream CB is capable of 100% fault current break within the entire range of protection.
[LS Industrial Systems]Селективность по сверхтокам
Данный метод применяется в том случае, когда автоматический выключатель, расположенный со стороны нагрузки, может в течение времени срабатывания выдержать 100 % тока короткого замыкания.
[Перевод Интент]Тематики
- выключатель автоматический
- предохранитель
- электротехника, основные понятия
- электроустановки
EN
- current discrimination
- discrimination method
- over-current discrimination
- overcurrent discrimination
- selectivity
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Überstromselektivität
-
9 maximaler unbeeinflußter Stoßstrom (eines Wechselstromkreises)
максимальный ожидаемый пиковый ток (цепи переменного тока)
Ожидаемый пиковый ток, возникающий в момент, обусловливающий его наибольшее возможное значение.
Примечание. В многофазной цепи многополюсного аппарата максимальный ожидаемый ток характеризует только один полюс
МЭК 60050(441-17-04).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
maximum prospective peak current (of an a.c. circuit)
the prospective peak current when initiation of the current takes place at the instant which leads to the highest possible value
NOTE – For a multiple device in a polyphase circuit, the maximum prospective peak current refers to a single pole only.
[IEV number 441-17-04]FR
valeur maximale de crête du courant présumé (d'un circuit à courant alternatif)
valeur de crête du courant présumé quand l'établissement du courant a lieu à l'instant qui conduit à la plus grande valeur possible
NOTE – Pour un appareil multipolaire dans un circuit polyphasé, la valeur maximale de crête du courant présumé ne se rapporte qu'à un seul pôle.
[IEV number 441-17-04]Тематики
- выключатель автоматический
- выключатель, переключатель
- электротехника, основные понятия
EN
- maximum prospective peak current (of an a.c. circuit)
DE
FR
- valeur maximale de crête du courant présumé (d'un circuit à courant alternatif)
Немецко-русский словарь нормативно-технической терминологии > maximaler unbeeinflußter Stoßstrom (eines Wechselstromkreises)
-
10 Sekundärstromauslöser
максимальный расцепитель тока косвенного действия
Максимальный расцепитель тока, питаемые током в главной цепи коммутационного аппарата через трансформатор тока или шунт.
[Интент]EN
indirect over-current release
an over-current release energized by the current in the main circuit of a mechanical switching device through a current transformer or a shunt.
[IEV number 441-16-37]
[IEC 62271-100, ed. 2.0 (2008-04)]FR
déclencheur indirect à maximum de courant
déclencheur à maximum de courant alimenté par le courant dans le circuit principal d’un appareil mécanique de connexion par I’intermédiaire d’un transformateur de courant ou d’un shunt.
[IEV number 441-16-37]
[IEC 62271-100, ed. 2.0 (2008-04)]
Недопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Sekundärstromauslöser
-
11 Primärstromauslöser
максимальный расцепитель тока прямого действия
Максимальный расцепитель тока, срабатывающий непосредственно от тока главной цепи коммутационного аппарата.
[Интент]EN
direct over-current release
an over-current release directly energized by the current in the main circuit of a mechanical switching device.
[IEV number 441-16-36]
[IEC 62271-100, ed. 2.0 (2008-04)]FR
déclencheur direct à maximum de courant
déclencheur à maximum de courant alimenté directement par le courant dans le circuit principal d’un appareil mécanique de connexion.
[IEV number 441-16-36]
[IEC 62271-100, ed. 2.0 (2008-04)]
Недопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Primärstromauslöser
-
12 abhängig verzögerter Überstromauslöser
максимальное реле или максимальный расцепитель тока с обратнозависимой выдержкой времени
Максимальное реле или максимальный расцепитель тока, срабатывающие с выдержкой времени, находящейся в обратной зависимости от значения сверхтока.
Примечание. Такие реле или расцепитель могут быть спроектированы так, чтобы при высоких значениях сверхтока выдержка времени достигала определенного минимального значения.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
максимальный расцепитель тока с обратно-зависимой выдержкой времени
Максимальный расцепитель тока, срабатывающий после выдержки времени, находящейся в обратной зависимости от значения сверхтока.
Примечание — Такой расцепитель может быть спроектирован так, чтобы эта выдержка времени при высоких значениях сверхтока достигала определенного минимального значения
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
inverse time-delay over-current release
an over-current release which operates after a time-delay inversely dependent upon the value of the over-current
NOTE - Such a release may be designed so that the time-delay approaches a definite minimum value for high values of over-current.
[IEV number 441-16-35]
[IEC 62271-100, ed. 2.0 (2008-04)]
inverse time-delay overcurrent release
overcurrent release which operates after a time-delay inversely dependent upon the value of the overcurrent
NOTE - Such a release may be designed so that the time-delay approaches a definite minimum for high values of overcurrent.
[IEV number 441-16-35]
[IEC 60898-1, ed. 1.0 (2002-01)]FR
déclencheur à maximum de courant à temps inverse
déclencheur à maximum de courant qui fonctionne après un intervalle de temps qui varie en raison inverse de la valeur de la surintensité
NOTE - Un tel déclencheur peut être prévu pour que le retard atteigne une valeur minimale définie pour les valeurs élevées de la surintensité.
[IEV number 441-16-35]
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEC 60898-1, ed. 1.0 (2002-01)]Недопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > abhängig verzögerter Überstromauslöser
-
13 Durchlaßstromkennlinie
характеристика тока отсечки (характеристика пропускания тока)
Кривая, отражающая зависимость тока отсечки от ожидаемого тока в указанных рабочих условиях.
Примечание.
В случае переменного тока значения токов отсечки — это максимальные значения, которые могут быть достигнуты при любой степени асимметрии.
В случае постоянного тока значения токов отсечки — это максимальные значения, достигнутые при указанной постоянной времени.
МЭК 60050(441-17-14).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
cut-off (current) characteristic
let-through (current) characteristic
a curve giving the cut-off current as a function of the prospective current, under stated conditions of operation
NOTE – In the case of a.c., the values of the cut-off currents are the maximum values which can be reached whatever the degree of asymmetry. In the case of d.c., the values of the cut-off currents are the maximum values reached related to the time constant as specified.
[IEV number 441-17-14]FR
caractéristique de courant coupé limité
courbe donnant, pour des conditions déterminées de fonctionnement, le courant coupé limité en fonction du courant présumé
NOTE – En courant alternatif, les valeurs du courant coupé limité sont les valeurs maximales quel que soit le degré d'asymétrie. En courant continu, ce sont les valeurs du courant coupé limité maximales atteintes compte tenu de la constante de temps spécifiée.
[IEV number 441-17-14]
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Durchlaßstromkennlinie
-
14 Grenzwerte von Eingangsstromstärke und -spannung
максимально допустимые значения входного тока и напряжения
-
[IEV number 314-04-05]EN
maximum permissible values of the input current and voltage
values of current and voltage assigned by the manufacturer which the transducer will withstand indefinitely without damage
[IEV number 314-04-05]FR
valeurs maximales admissibles du courant et de la tension d’entrée
valeurs du courant et de la tension indiquées par le constructeur comme étant les valeurs que le transducteur peut supporter indéfiniment sans dommage
[IEV number 314-04-05]Тематики
- измерение электр. величин в целом
EN
DE
FR
- valeurs maximales admissibles du courant et de la tension d’entrée
Немецко-русский словарь нормативно-технической терминологии > Grenzwerte von Eingangsstromstärke und -spannung
-
15 Selektivitäts-Grenzstrom
предельный ток селективности Is Токовая координата точки пересечения полной время-токовой характеристики защитного аппарата со стороны нагрузки и преддуговой (для плавких предохранителей) время-токовой характеристики или время-токовой характеристики расцепления второго защитного аппарата.
Предельный ток селективности (см. рисунок А.1) — это предельное значение тока:- ниже которого при последовательном соединении двух аппаратов защиты от сверхтоков защитный аппарат со стороны нагрузки завершает операцию отключения, чтобы воспрепятствовать началу действия второго защитного аппарата (т. е. обеспечивается селективность);
- выше которого при последовательном соединении двух аппаратов защиты от сверхтоков защитный аппарат со стороны нагрузки может не успеть вовремя завершить операцию отключения, чтобы воспрепятствовать началу действия второго защитного аппарата (т. е. селективность не обеспечивается).
Is - предельный ток селективности;
Icu - номинальная предельная наибольшая отключающая способность;
А - преддуговая характеристика плавкого предохранителя;
В - рабочая характеристика плавкого предохранителя;
С - рабочая характеристика нетокоограничивающего выключателя (N) (время отключения/ток и I2t/ток) Примечания.
1. А считают нижним пределом, В и С - верхними пределами.
2. Недиабатическая зона для I2t показана пунктиром Рис. А1.
Координация по сверхтокам между автоматическим выключателем и предохранителем
или резервной защитой, осуществляемой предохранителем.
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]EN
selectivity-limit current
the current coordinate of the intersection between the maximum break time-current characteristic of the protective device on the load side and the pre-arcing (for fuses) or tripping (for residual current devices) time-current characteristic of the other protective device
[IEV number 442-05-60]FR
courant limite
coordonnée du courant de l'intersection entre la caractéristique de durée maximale de coupure temps-courant du dispositif de protection côté aval et la caractéristique temps-courant de pré-arc (pour les fusibles) ou de déclenchement (pour les dispositifs de coupure différentiels) de l'autre dispositif de protection.
[IEV number 442-05-60]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
Синонимы
- Is
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Selektivitäts-Grenzstrom
-
16 Schaltanlage
распределительное устройство
Распределительным устройством (РУ) называется электроустановка, служащая для приема и распределения электроэнергии и содержащая сборные и соединительные шины, коммутационные аппараты, вспомогательные устройства (компрессорные, аккумуляторные и др.), а также устройства защиты, автоматики и измерительные приборы.
[РД 34.20.185-94]
распределительное устройство
Электроустановка, предназначенная для приема и распределения электрической энергии на одном напряжении и содержащая коммутационные аппараты и соединяющие их сборные шины [секции шин], устройства управления и защиты.
Примечание. К устройствам управления относятся аппараты и связывающие их элементы обеспечивающие контроль, измерение, сигнализацию и выполнение команд.
[ ГОСТ 24291-90]
[ ГОСТ Р 53685-2009]
электрическое распределительное устройство
распределительное устройство
Устройство, предназначенное для приема и распределения электроэнергии на одном напряжении и содержащее коммутационные аппараты и соединяющие их сборные соединительные устройства.
Примечание. В состав распределительного устройства дополнительно могут входить устройства защиты и управления
[ОСТ 45.55-99]
распределительное устройство
Электроустановка, служащая для приема и распределения электроэнергии и содержащая коммутационные аппараты, сборные и соединительные шины, вспомогательные устройства (компрессорные, аккумуляторные и др.), а также устройства защиты, автоматики и измерительные приборы.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]
устройство распределительное
Совокупность аппаратов и приборов для приёма и распределения электроэнергии одного напряжения, вырабатываемой электростанцией или преобразуемой подстанцией
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
switching substation
a substation which includes switchgear and usually busbars, but no power transformers
[IEV number 605-01-02]FR
poste de sectionnement
poste de coupure
poste comprenant des organes de manoeuvre et généralement des jeux de barres, à l'exclusion de transformateurs de puissance
[IEV number 605-01-02]В качестве РУ 6—10 кВ используется сборка высокого напряжения с однополюсными разъединителями и вертикальным расположением фаз одного присоединения и одна камера КСО с выключателем нагрузки и предохранителями для подключения трансформатора. Для РУ 0,4 кВ применяются сборки низкого напряжения с предохранителями и вертикальным расположением фаз одного присоединения.
На ПС применяются открытые (ОРУ), закрытые (ЗРУ) или комплектные (КРУ) распределительные устройства.
[ http://energy-ua.com/elektricheskie-p/klassifikatsiya.html]
В общем случае ПС и РУ являются составной частью электроустановок, которые различаются:
-
по назначению:
- генерирующие,
- преобразовательно-распределительные,
-
потребительские.
Генерирующие электроустановки служат для выработки электроэнергии, преобразовательно-распределительные электроустановки преобразуют электроэнергию в удобный для передачи и потребления вид, передают ее и распределяют между потребителями;
-
по роду тока:
- постоянного тока,
- переменного тока.
-
по напряжению:
- до 1000 В,
- выше 1000 В.
ГОСТ 29322—92 установлена следующая шкала номинальных напряжений:
Шкала номинальных напряжений ограничена сравнительно небольшим числом стандартных значений, благодаря чему изготавливается небольшое число типоразмеров машин и оборудования, а электросети выполняются более экономичными. В установках трехфазного тока номинальным напряжением принято считать напряжение между фазами (междуфазовое напряжение). Согласнодля электросетей переменного тока частотой 50 Гц междуфазовое напряжение должно быть: 12, 24, 36, 42, 127, 220, 380 В; 3, 6, 10, 20, 35, 110, 150, 220, 330, 500, 750 и 1150 кВ;
для электросетей постоянного тока: 12, 24, 36, 48, 60, 110, 220, 440, 660, 825, 3000 В и выше.-
по способу присоединения к электросети ПС разделяются на:
- тупиковые (блочные),
- ответвительные (блочные),
- проходные (транзитные)
- узловые.
Тупиковые ПС получают питание по одной или двум тупиковым ВЛ.
Ответвительные ПС присоединяются ответвлением к одной или двум проходящим ВЛ с односторонним или двухсторонним питанием.
Проходные ПС включаются в рассечку одной или двух проходящих ВЛ с односторонним или двухсторонним питанием.
Узловые ПС кроме питающих имеют отходящие радиальные или транзитные ВЛ.-
по способу управления ПС могут быть:
- только с телесигнализацией,
- телеуправляемыми с телесигнализацией,
- с телесигнализацией и управлением с общеподстанционного пункта управления (ОПУ).
Подстанции оперативно обслуживаются постоянным дежурным персоналом на щите управления, дежурными на дому или оперативно-выездными бригадами (ОВБ). Ремонт ПС осуществляется специализированными выездными бригадами централизованного ремонта или местным персоналом подстанции.
В РУ напряжением до 1000 В провода, шины, аппараты, приборы и конструкции выбирают как по нормальным условиям работы (напряжению и току), так и по термическим и динамическим воздействиям токов коротких замыканий (КЗ) или предельно допустимой отключаемой мощности.
В РУ и ПС напряжением выше 1000 В расстояния между электрооборудованием, аппаратами, токоведущими частями, изоляторами, ограждениями и конструкциями устанавливаются так, чтобы при нормальном режиме работы электроустановки возникающие физические явления (температура нагрева, электрическая дуга, выброс газов, искрение и др.) не могли привести к повреждению оборудования и КЗ.[ http://energy-ua.com/elektricheskie-p/klassifikatsiya.html]
Several different classifications of switchgear can be made:- By the current rating.
-
By interrupting rating (maximum short circuit current that the device can safely interrupt)
- Circuit breakers can open and close on fault currents
- Load-break/Load-make switches can switch normal system load currents
- Isolators may only be operated while the circuit is dead, or the load current is very small.
-
By voltage class:
- Low voltage (less than 1,000 volts AC)
- Medium voltage (1,000–35,000 volts AC)
- High voltage (more than 35,000 volts AC)
-
By insulating medium:
-
By construction type:
- Indoor (further classified by IP (Ingress Protection) class or NEMA enclosure type)
- Outdoor
- Industrial
- Utility
- Marine
- Draw-out elements (removable without many tools)
- Fixed elements (bolted fasteners)
- Live-front
- Dead-front
- Open
- Metal-enclosed
- Metal-clad
- Metal enclosed & Metal clad
- Arc-resistant
-
By IEC degree of internal separation
- No Separation (Form 1)
- Busbars separated from functional units (Form 2a, 2b, 3a, 3b, 4a, 4b)
- Terminals for external conductors separated from busbars (Form 2b, 3b, 4a, 4b)
- Terminals for external conductors separated from functional units but not from each other (Form 3a, 3b)
- Functional units separated from each other (Form 3a, 3b, 4a, 4b)
- Terminals for external conductors separated from each other (Form 4a, 4b)
- Terminals for external conductors separate from their associated functional unit (Form 4b)
-
By interrupting device:
-
By operating method:
- Manually operated
- Motor/stored energy operated
- Solenoid operated
-
By type of current:
-
By application:
-
By purpose
- Isolating switches (disconnectors)
- Load-break switches.
- Grounding (earthing) switches
A single line-up may incorporate several different types of devices, for example, air-insulated bus, vacuum circuit breakers, and manually operated switches may all exist in the same row of cubicles.
Ratings, design, specifications and details of switchgear are set by a multitude of standards. In North America mostly IEEE and ANSI standards are used, much of the rest of the world uses IEC standards, sometimes with local national derivatives or variations.
[Robert W. Smeaton (ed) Switchgear and Control Handbook 3rd Ed., Mc Graw Hill, new York 1997]
[ http://en.wikipedia.org/wiki/High_voltage_switchgear]Тематики
- электрификация, электроснабж. железных дорог
- электроагрегаты генераторные
- электробезопасность
- электроснабжение в целом
Синонимы
EN
- distribution
- energy distribution board
- gear
- switch-gear
- switchboard
- switchgear
- switching substation
- switchyard
DE
FR
36. Электрическое распределительное устройство
Распределительное устройство
D. Schaltanlage
E. Switch-gear
По ГОСТ 24291
Источник: ГОСТ 20375-83: Электроагрегаты и передвижные электростанции с двигателями внутреннего сгорания. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Schaltanlage
-
по назначению:
-
17 Schaltstation
распределительное устройство
Распределительным устройством (РУ) называется электроустановка, служащая для приема и распределения электроэнергии и содержащая сборные и соединительные шины, коммутационные аппараты, вспомогательные устройства (компрессорные, аккумуляторные и др.), а также устройства защиты, автоматики и измерительные приборы.
[РД 34.20.185-94]
распределительное устройство
Электроустановка, предназначенная для приема и распределения электрической энергии на одном напряжении и содержащая коммутационные аппараты и соединяющие их сборные шины [секции шин], устройства управления и защиты.
Примечание. К устройствам управления относятся аппараты и связывающие их элементы обеспечивающие контроль, измерение, сигнализацию и выполнение команд.
[ ГОСТ 24291-90]
[ ГОСТ Р 53685-2009]
электрическое распределительное устройство
распределительное устройство
Устройство, предназначенное для приема и распределения электроэнергии на одном напряжении и содержащее коммутационные аппараты и соединяющие их сборные соединительные устройства.
Примечание. В состав распределительного устройства дополнительно могут входить устройства защиты и управления
[ОСТ 45.55-99]
распределительное устройство
Электроустановка, служащая для приема и распределения электроэнергии и содержащая коммутационные аппараты, сборные и соединительные шины, вспомогательные устройства (компрессорные, аккумуляторные и др.), а также устройства защиты, автоматики и измерительные приборы.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]
устройство распределительное
Совокупность аппаратов и приборов для приёма и распределения электроэнергии одного напряжения, вырабатываемой электростанцией или преобразуемой подстанцией
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
switching substation
a substation which includes switchgear and usually busbars, but no power transformers
[IEV number 605-01-02]FR
poste de sectionnement
poste de coupure
poste comprenant des organes de manoeuvre et généralement des jeux de barres, à l'exclusion de transformateurs de puissance
[IEV number 605-01-02]В качестве РУ 6—10 кВ используется сборка высокого напряжения с однополюсными разъединителями и вертикальным расположением фаз одного присоединения и одна камера КСО с выключателем нагрузки и предохранителями для подключения трансформатора. Для РУ 0,4 кВ применяются сборки низкого напряжения с предохранителями и вертикальным расположением фаз одного присоединения.
На ПС применяются открытые (ОРУ), закрытые (ЗРУ) или комплектные (КРУ) распределительные устройства.
[ http://energy-ua.com/elektricheskie-p/klassifikatsiya.html]
В общем случае ПС и РУ являются составной частью электроустановок, которые различаются:
-
по назначению:
- генерирующие,
- преобразовательно-распределительные,
-
потребительские.
Генерирующие электроустановки служат для выработки электроэнергии, преобразовательно-распределительные электроустановки преобразуют электроэнергию в удобный для передачи и потребления вид, передают ее и распределяют между потребителями;
-
по роду тока:
- постоянного тока,
- переменного тока.
-
по напряжению:
- до 1000 В,
- выше 1000 В.
ГОСТ 29322—92 установлена следующая шкала номинальных напряжений:
Шкала номинальных напряжений ограничена сравнительно небольшим числом стандартных значений, благодаря чему изготавливается небольшое число типоразмеров машин и оборудования, а электросети выполняются более экономичными. В установках трехфазного тока номинальным напряжением принято считать напряжение между фазами (междуфазовое напряжение). Согласнодля электросетей переменного тока частотой 50 Гц междуфазовое напряжение должно быть: 12, 24, 36, 42, 127, 220, 380 В; 3, 6, 10, 20, 35, 110, 150, 220, 330, 500, 750 и 1150 кВ;
для электросетей постоянного тока: 12, 24, 36, 48, 60, 110, 220, 440, 660, 825, 3000 В и выше.-
по способу присоединения к электросети ПС разделяются на:
- тупиковые (блочные),
- ответвительные (блочные),
- проходные (транзитные)
- узловые.
Тупиковые ПС получают питание по одной или двум тупиковым ВЛ.
Ответвительные ПС присоединяются ответвлением к одной или двум проходящим ВЛ с односторонним или двухсторонним питанием.
Проходные ПС включаются в рассечку одной или двух проходящих ВЛ с односторонним или двухсторонним питанием.
Узловые ПС кроме питающих имеют отходящие радиальные или транзитные ВЛ.-
по способу управления ПС могут быть:
- только с телесигнализацией,
- телеуправляемыми с телесигнализацией,
- с телесигнализацией и управлением с общеподстанционного пункта управления (ОПУ).
Подстанции оперативно обслуживаются постоянным дежурным персоналом на щите управления, дежурными на дому или оперативно-выездными бригадами (ОВБ). Ремонт ПС осуществляется специализированными выездными бригадами централизованного ремонта или местным персоналом подстанции.
В РУ напряжением до 1000 В провода, шины, аппараты, приборы и конструкции выбирают как по нормальным условиям работы (напряжению и току), так и по термическим и динамическим воздействиям токов коротких замыканий (КЗ) или предельно допустимой отключаемой мощности.
В РУ и ПС напряжением выше 1000 В расстояния между электрооборудованием, аппаратами, токоведущими частями, изоляторами, ограждениями и конструкциями устанавливаются так, чтобы при нормальном режиме работы электроустановки возникающие физические явления (температура нагрева, электрическая дуга, выброс газов, искрение и др.) не могли привести к повреждению оборудования и КЗ.[ http://energy-ua.com/elektricheskie-p/klassifikatsiya.html]
Several different classifications of switchgear can be made:- By the current rating.
-
By interrupting rating (maximum short circuit current that the device can safely interrupt)
- Circuit breakers can open and close on fault currents
- Load-break/Load-make switches can switch normal system load currents
- Isolators may only be operated while the circuit is dead, or the load current is very small.
-
By voltage class:
- Low voltage (less than 1,000 volts AC)
- Medium voltage (1,000–35,000 volts AC)
- High voltage (more than 35,000 volts AC)
-
By insulating medium:
-
By construction type:
- Indoor (further classified by IP (Ingress Protection) class or NEMA enclosure type)
- Outdoor
- Industrial
- Utility
- Marine
- Draw-out elements (removable without many tools)
- Fixed elements (bolted fasteners)
- Live-front
- Dead-front
- Open
- Metal-enclosed
- Metal-clad
- Metal enclosed & Metal clad
- Arc-resistant
-
By IEC degree of internal separation
- No Separation (Form 1)
- Busbars separated from functional units (Form 2a, 2b, 3a, 3b, 4a, 4b)
- Terminals for external conductors separated from busbars (Form 2b, 3b, 4a, 4b)
- Terminals for external conductors separated from functional units but not from each other (Form 3a, 3b)
- Functional units separated from each other (Form 3a, 3b, 4a, 4b)
- Terminals for external conductors separated from each other (Form 4a, 4b)
- Terminals for external conductors separate from their associated functional unit (Form 4b)
-
By interrupting device:
-
By operating method:
- Manually operated
- Motor/stored energy operated
- Solenoid operated
-
By type of current:
-
By application:
-
By purpose
- Isolating switches (disconnectors)
- Load-break switches.
- Grounding (earthing) switches
A single line-up may incorporate several different types of devices, for example, air-insulated bus, vacuum circuit breakers, and manually operated switches may all exist in the same row of cubicles.
Ratings, design, specifications and details of switchgear are set by a multitude of standards. In North America mostly IEEE and ANSI standards are used, much of the rest of the world uses IEC standards, sometimes with local national derivatives or variations.
[Robert W. Smeaton (ed) Switchgear and Control Handbook 3rd Ed., Mc Graw Hill, new York 1997]
[ http://en.wikipedia.org/wiki/High_voltage_switchgear]Тематики
- электрификация, электроснабж. железных дорог
- электроагрегаты генераторные
- электробезопасность
- электроснабжение в целом
Синонимы
EN
- distribution
- energy distribution board
- gear
- switch-gear
- switchboard
- switchgear
- switching substation
- switchyard
DE
FR
3 (электрическое) распределительное устройство; РУ
Электроустановка, предназначенная для приема и распределения электрической энергии на одном напряжении и содержащая коммутационные аппараты и соединяющие их сборные шины [секции шин], устройства управления и защиты.
Примечание. К устройствам управления относятся аппараты и связывающие их элементы, обеспечивающие контроль, измерение, сигнализацию и выполнение команд
605-01-02**
de Schaltstation
en switching substation
fr poste de sectionnement, poste de coupure
Источник: ГОСТ 24291-90: Электрическая часть электростанции и электрической сети. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Schaltstation
-
по назначению:
-
18 Durchlaßstrom
ток отсечки
Максимальное мгновенное значение тока, достигаемое в процессе отключения тока коммутационным аппаратом или плавким предохранителем.
МЭК 60050 (441-17-12).
Примечание. Понятие особенно важно, когда коммутационный аппарат или плавкий предохранитель срабатывает так, что ожидаемый пиковый ток цепи не достигается.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
cut-off current
let-through current
the maximum instantaneous value of current attained during the breaking operation of a switching device or a fuse
NOTE – This concept of particular importance when the switching device or the fuse operates in such a manner that the prospective peak current of the circuit is not reached.
[IEV number 441-17-12]FR
courant coupé limité
valeur instantanée maximale du courant atteinte au cours de la coupure effectuée par un appareil de connexion ou un fusible
NOTE – Cette notion est d'importance particulière si l'appareil de connexion ou le fusible fonctionne de telle manière que la valeur de crête du courant présumé du circuit n'est pas atteinte.
[IEV number 441-17-12]Примечание
Более подробно о токе отсечки см. " защитная характеристика автоматического выключателя"Тематики
- выключатель автоматический
- выключатель, переключатель
- предохранитель
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Durchlaßstrom
-
19 Nichtauslösestrom (eines Überlastauslösers)
условный ток нерасцепления Int
Установленное значение тока, который автоматический выключатель для электрооборудования способен проводить заданное (условное) время без расцепления.
[ ГОСТ Р 50031-99( МЭК 60934-93)]
условный ток нерасцепления (максимального реле или расцепителя тока)
Установленное значение тока, который реле или расцепитель способны проводить, не срабатывая, в течение заданного (условного) времени.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
conventional non-tripping current
a specified value of current which the circuit-breaker is capable of carrying for a specified time designated as conventional time, without tripping
[IEV number 442-05-54]
conventional non-tripping current (of an over-current release)
a specified value of current which the release can carry for a specified time (conventional time) without operating
[IEV number 441-17-22]FR
courant conventionnel de non-déclenchement
valeur spécifiée du courant que le disjoncteur peut supporter sans déclencher pendant un temps spécifié appelé temps conventionnel
[IEV number 442-05-54]
courant conventionnel de non-déclenchement (d'un déclencheur à maximum de courant)
valeur spécifiée de courant que peut supporter un déclencheur pendant une durée spécifiée (durée conventionnelle) sans fonctionner
[IEV number 441-17-22]Тематики
Синонимы
EN
DE
- Nichtauslösestrom (eines Überlastauslösers)
- vereinbarte Nichtauslösestromstärke
- vereinbarter Nichtauslösestrom
FR
Немецко-русский словарь нормативно-технической терминологии > Nichtauslösestrom (eines Überlastauslösers)
-
20 vereinbarte Nichtauslösestromstärke
условный ток нерасцепления Int
Установленное значение тока, который автоматический выключатель для электрооборудования способен проводить заданное (условное) время без расцепления.
[ ГОСТ Р 50031-99( МЭК 60934-93)]
условный ток нерасцепления (максимального реле или расцепителя тока)
Установленное значение тока, который реле или расцепитель способны проводить, не срабатывая, в течение заданного (условного) времени.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
conventional non-tripping current
a specified value of current which the circuit-breaker is capable of carrying for a specified time designated as conventional time, without tripping
[IEV number 442-05-54]
conventional non-tripping current (of an over-current release)
a specified value of current which the release can carry for a specified time (conventional time) without operating
[IEV number 441-17-22]FR
courant conventionnel de non-déclenchement
valeur spécifiée du courant que le disjoncteur peut supporter sans déclencher pendant un temps spécifié appelé temps conventionnel
[IEV number 442-05-54]
courant conventionnel de non-déclenchement (d'un déclencheur à maximum de courant)
valeur spécifiée de courant que peut supporter un déclencheur pendant une durée spécifiée (durée conventionnelle) sans fonctionner
[IEV number 441-17-22]Тематики
Синонимы
EN
DE
- Nichtauslösestrom (eines Überlastauslösers)
- vereinbarte Nichtauslösestromstärke
- vereinbarter Nichtauslösestrom
FR
Немецко-русский словарь нормативно-технической терминологии > vereinbarte Nichtauslösestromstärke
См. также в других словарях:
maximum current — didžiausioji srovė statusas T sritis Standartizacija ir metrologija apibrėžtis Didžiausias srovės stipris, kuriam esant elektros skaitiklis dar atitinka norminius tikslumo reikalavimus. atitikmenys: angl. maximum current vok. Maximalstrom, m rus … Penkiakalbis aiškinamasis metrologijos terminų žodynas
maximum current breaker — didžiausiosios ribinės srovės išjungiklis statusas T sritis radioelektronika atitikmenys: angl. maximum current breaker; overcurrent circuit breaker vok. Überstromschalter, m; Überstromschutzschalter, m rus. автомат максимального тока, m pranc.… … Radioelektronikos terminų žodynas
Current limiting — is the practice in electrical or electronic circuits of imposing an upper limit on the current that may be delivered to a load with the purpose of protecting the circuit generating or transmitting the current from harmful effects due to a short… … Wikipedia
Current density — This page is about the electric current density in electromagnetism. For the probability current density in quantum mechanics, see Probability current. Current density is a measure of the density of flow of a conserved charge. Usually the charge… … Wikipedia
Maximum power point tracking — Current voltage characteristics of a solar cell at a particular light level, and in darkness. The area of the yellow rectangle gives the output power. Pmax denotes the maximum power point Maximum power point tracking (MPPT) is a technique that… … Wikipedia
Maximum Fighting Championship — Type Private Industry Mixed martial arts promotion Founded 2001 Founder(s) … Wikipedia
Current Issues and Events — (commonly known as Current Events) is one of several academic events sanctioned by the University Interscholastic League. The contest began in the 1990 91 scholastic year.Current Events is designed to test students knowledge and understanding of… … Wikipedia
Maximum parsimony — Maximum parsimony, often simply referred to as parsimony, is a non parametric statistical method commonly used in computational phylogenetics for estimating phylogenies. Under maximum parsimony, the preferred phylogenetic tree is the tree that… … Wikipedia
Maximum PC — September 2010 cover Editor in Chief George Jones Categories Computing Frequency Monthly Total … Wikipedia
Maximum-Football — Cover art Developer(s) Wintervalley Software Publisher(s) Matrix Games … Wikipedia
Maximum Destruction — ost the Monster Jam in Stafford Springs, CT Owner and Driver Information Owner Tom Meents Driver(s) Tom Meents and Neil Elliott Home … Wikipedia