-
1 масляный трансформатор
масляный трансформатор
Трансформатор с жидким диэлектриком, в котором основной изолирующей средой и теплоносителем служит трансформаторное масло
[ ГОСТ 16110-82]
масляный трансформатор
Трансформатор, магнитная система и обмотки которого погружены в масло
(МЭС 421-01-14)
[ ГОСТ 30830-2002]EN
oil-immersed type transformer
a transformer of which the magnetic circuit and windings are immersed in oi
[IEV number 421-01-14]FR
transformateur immergé dans l'huile
transformateur dont le circuit magnétique et les enroulements sont immergés dans l'huile
[IEV number 421-01-14]Oil transformers
The magnetic circuit and the windings are immersed in a liquid dielectric that provides insulation and evacuates the heat losses of the transformer.
This liquid expands according to the load and the ambient temperature. PCBs and TCBs are now prohibited and mineral oil is generally used. It is flammable and requires protective measures against the risks of fire, explosion and pollution.
The most commonly used protective measures are the DGPT or the DGPT2: Gas, Pressure and Temperature sensor with 1 or 2 sensing levels on the temperature. This system cuts off the LV load (1st level) then the HV supply (2nd level) when there is a fault inside the transformer. A holding tank is used to recover all the liquid dielectric.
Of the four types of immersed transformer: free breathing transformers, gas cushion transformers, transformers with expansion tank and transformers with integral filling, only the latter are currently installed.
[Legrand]Масляные трансформаторы
Магнитная система и обмотки трансформатора погружены в жидкий диэлектрик, служащий изоляцией и теплоносителем.
Жидкий диэлектрик изменяет свой объем в соответствии с нагрузкой трансформатора и температурой окружающей среды. Поскольку в настоящее время применение полихлорированных дифенилов и тетрахлорбифенилов запрещено, то в основном используют минеральное масло. Оно огнеопасно, поэтому необходимо принимать меры против возникновения пожара, взрыва и загрязнения окружающей среды.
Как правило, применяются системы DGPT (одноуровневые системы, использующие датчики газа, давления и температуры) или DGPT2 – двухуровневые системы. В случае возникновения аномального состояния трансформатора данные системы отключают нагрузку цепей низшего напряжения (первый уровень защиты), а затем питание обмотки высшего напряжения (второй уровень защиты). Активная часть трансформатора находится в баке и полностью покрыта жидким диэлектриком.
Существует четыре типа масляных трансформаторов: трансформаторы с системой свободного дыхания, трансформаторы с газовой подушкой между зеркалом масла и крышкой трансформатора, трансформаторы с расширительным баком и трансформаторы с гофрированным баком. В настоящее время применяют только трансформаторы последнего типа
[Интент]
[http://www.ramo-chelny.ru/konschasti.html]Масляный трансформатор:
- Шихтованный магнитопровод
- Обмотка низшего напряжения
- Обмотка высшего напряжения
- Трубчатый бак
- Термометр
- Переключатель регулировочных отводов обмотки высшего напряжения
- Ввод (проходной изолятор) обмотки низшего напряжения
- Ввод (проходной изолятор) обмотки высшего напряжения
- Расширительный бак
[http://transfcomplect.narod.ru/transformator.html]Тематики
Классификация
>>>EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > масляный трансформатор
-
2 ввод с бумажно-масляной изоляцией
- traversée en papier imprégné d’huile
- OIP
ввод с бумажно-масляной изоляцией
Ввод, в котором основная изоляция состоит из бумаги, пропитанной изоляционной жидкостью.
Примечание. Бумага, в основном, пропитывается трансформаторным маслом.
[ ГОСТ 27744-88]EN
oil-impregnated paper bushing
OIP
bushing in which the major insulation consists of a core wound from paper and subsequently treated and impregnated with an insulating liquid, generally transformer oil
NOTE The core is contained in an insulating envelope, the space between the core and the insulating envelope being filled with the same insulating liquid as that used for impregnation.
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée en papier imprégnée d'huile
OIP (oil-impregnated paper)
traversée dont l'isolation principale est assurée par un corps enroulé en papier ultérieurement traité et imprégné d'un liquide isolant, généralement d'huile de transformateur
NOTE Le corps est placé dans une enveloppe isolante, l'espace entre le corps et l'enveloppe isolante étant rempli du même liquide isolant que celui employé pour l'imprégnation
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
DE
FR
- OIP
- traversée en papier imprégné d’huile
Русско-французский словарь нормативно-технической терминологии > ввод с бумажно-масляной изоляцией
-
3 ввод с жидкой изоляцией
ввод с жидкой изоляцией
Ввод, основной изоляцией которого является изоляционная жидкость.
[ ГОСТ 27744-88]EN
liquid-insulated bushing
bushing in which the major insulation consists of oil or another insulating liquid
[IEC 60137, ed. 6.0 (2008-07)]FR
traversée à isolation liquide
traversée dont l'isolation principale est assurée par de l'huile ou par un autre isolant liquide
[IEC 60137, ed. 6.0 (2008-07)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > ввод с жидкой изоляцией
-
4 бак трансформатора
бак трансформатора
Бак, в котором размещается активная часть трансформатора или трансформаторного агрегата с жидким диэлектриком, газо- или кварценаполненного
[ ГОСТ 16110-82]EN
tank
the vessel in which the core, yoke and windings of a transformer or reactor are contained
[IEV number 811-26-31]FR
cuve
récipient dans lequel le circuit magnétique et les enroulements d'un transformateur ou d'une inductance sont contenus
[IEV number 811-26-31]Параллельные тексты EN-RU
Oil transformers
The magnetic circuit and the windings are immersed in a liquid dielectric that provides insulation and evacuates the heat losses of the transformer.
...
A holding tank is used to recover all the liquid dielectric.
[Legrand]Масляные трансформаторы
Магнитная система и обмотки трансформатора погружены в жидкий диэлектрик, служащий изоляцией и теплоносителем.
...
Активная часть трансформатора находится в баке и полностью покрыта жидким диэлектриком.
[Перевод Интент]
Бак трансформатора
Бак служит для установки в нем активной части трансформатора и заливки масла (некоторые баки специальных трансформаторов заполняют газом или кварцем); он состоит из обвязки 3, дна 4, рамы 2 и крышки 1 с отверстиями для крепления болтами к раме. Крышка закрывает бак и одновременно является основанием для установки расширителя, вводов, приводов переключающих устройств, баллона термосигнализатора, подъемных колец и других деталей (рис. 2). Место разъема крышки с баком уплотняют резиновой полосой, укладываемой на раму в уступ между выступающим торцом обечайки и отверстиями в раме.
Основные части бака трансформатораКрышка баков трансформаторов мощностью 25 MB-А и выше приварена к обечайке. Бак имеет нижний разъем и состоит из верхней (высокой) съемной части и нижней, являющейся его основанием (днищем). Такое устройство облегчает разборку и сборку трансформаторов и не требует механизмов большой грузоподъемности, поскольку вместо активной части поднимают верхнюю часть бака.
Для перемещения трансформаторов (при монтаже, ремонте) массой до 20 т под днищем устанавливают тележки (по две на трансформатор), при большей массе — каретки; для подъема трансформатора стропами к стенкам бака приварены крюки; для крепления охладителей и термосифонных фильтров — патрубки с фланцами; для заполнения трансформатора маслом установлены вентили.
Баки трансформаторов III габарита и более мощных усиливают поперечными и продольными балками из стального проката (швеллер, тавр, уголок). Механическую прочность бака и непроницаемость сварных швов испытывают избыточным давлением 30—50 кПа.
Крышка трансформатора ТМ-400/10 (вид сверху):1 — фланец для соединения с расширителем, 2 — рым, 3 — ввод ВН, 4 — переключатель, 5 — кран, 6 — термометр, 7 — пробивной предохранитель, 8 — ввод нейтрали НН, 9 — линейный ввод НН, 10 — крышка, 11 — место установки расширителя
Для трансформаторов I—V габаритов применяют баки овальной формы, больших габаритов — прямоугольные, с пространственным магнитопроводом—треугольные или круглые. Их изготовляют из листовой стали; стыки листов соединяют привариванием газо- или электросваркой.[http://forca.ru/spravka/spravka/bak-transformatora.html]
Тематики
Классификация
>>>Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > бак трансформатора
-
5 ввод (проходной изолятор)
ввод
Проходной изолятор, имеющий внутреннюю изоляцию из жидкого, твердого, газообразного диэлектрического материала или их комбинации.
[ ГОСТ 27744-88 ]EN
bushing
device that enables one or several conductors to pass through a partition such as a wall or a tank, and insulate the conductors from it.
NOTE 1 – The means of attachment (flange or fixing device) to the partition forms part of the bushing. The conductor may form an integral part of the bushing or be drawn into the central tube of the bushing.
NOTE 2 – The bushings may be of the following types:
- liquid-filled bushing;
- liquid-insulated bushing;
- gas-filled bushing;
- gas-insulated bushing;
- oil-impregnated paper bushing;
- resin-bonded paper bushing;
- resin-impregnated paper bushing;
- ceramic, glass or analogous inorganic material bushing;
- cast or moulded resin-insulated bushing;
- combined insulation bushing;
- compound-filled bushing;
- gas-impregnated bushing.
[IEV number 471-02-01]FR
traversée
dispositif servant à faire passer un ou plusieurs conducteurs à travers une paroi, telle qu’un mur ou une cuve, en isolant le(s) conducteur(s) de cette paroi.
NOTE 1 – Les moyens de fixation (bride ou autre dispositif) sur la paroi font partie de la traversée. Le conducteur peut être solidaire de la traversée ou démontable.
NOTE 2 – Les différentes traversées peuvent être les suivantes:
- traversée à remplissage d’un liquide;
- traversée à isolation liquide;
- traversée à remplissage de gaz;
- traversée à isolation gazeuse;
- traversée en papier imprégné d’huile;
- traversée en papier enduit de résine;
- traversée en papier imprégné de résine;
- traversée en matière céramique, en verre ou en matière inorganique analogue;
- traversée à isolation en résine coulée ou moulée;
- traversée à isolation combinée;
- traversée à remplissage de mélange;
- traversée imprégnée de gaz.
[IEV number 471-02-01]Тематики
EN
DE
- Durchführung, f
FR
Русско-французский словарь нормативно-технической терминологии > ввод (проходной изолятор)
-
6 бытовое жидкое топливо
бытовое жидкое топливо
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
domestic fuel oil
Liquid petroleum product used in domestic heaters. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > бытовое жидкое топливо
-
7 нефтяной сланец
нефтяной сланец
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
oil shale
A kerogen-bearing, finely laminated brown or black sedimentary rock that will yield liquid or gaseous hydrocarbons on distillation. (Source: BJGEO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > нефтяной сланец
-
8 топливные нефтепродукты
топливные нефтепродукты
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
fuel oil
A liquid product burned to generate heat, exclusive of oils with a flash point below 38Đ°C; includes heating oils, stove oils, furnace oils, bunker fuel oils. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > топливные нефтепродукты
-
9 вакуумный насос с масляным (жидкостным) уплотнением
вакуумный насос с масляным (жидкостным) уплотнением
Вакуумный насос объемного действия, в котором для заполнения зазоров между движущимися относительно друг друга рабочими частями насоса и для уменьшения вредного пространства в рабочей камере в конце процесса сжатия используют вакуумное масло или жидкость.
[ ГОСТ 5197-85]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > вакуумный насос с масляным (жидкостным) уплотнением
См. также в других словарях:
Oil and Water — may refer to: a mixture of oil and water (see multiphasic liquid) Oil and Water (song), a 2007 single by American alternative rock band Incubus Oil Water, a 2003 EP by New Zealand rock band Evermore Oil and Water (1913 film), a 1913 film This… … Wikipedia
oil — oil1 [ ɔıl ] noun *** ▸ 1 liquid for fuel ▸ 2 used in engines ▸ 3 used in cooking ▸ 4 type of paint ▸ 5 for your skin ▸ + PHRASES 1. ) uncount a thick dark smooth liquid from under the ground, used for making gas and other fuels: The Middle… … Usage of the words and phrases in modern English
oil — I UK [ɔɪl] / US noun Word forms oil : singular oil plural oils *** 1) a) [uncountable] a thick dark smooth liquid from under the ground, used for making petrol and other fuels The Middle Eastern countries produce most of the world s oil. We need… … English dictionary
oil shale — Geol. a black or dark brown shale or siltstone rich in bitumens, from which shale oil is obtained by destructive distillation. [1870 75] * * * Any fine grained sedimentary rock that contains solid organic matter (kerogen) and yields significant… … Universalium
Oil and Gas Industry metering and control system — IntroductionRemote Gas well sites require local flow metering of the mineral reserve s gas flow rate for asset and revenue accounting purposes. Traditionally, local flow metering was done using high maintenance mechanical circular chart recorders … Wikipedia
Oil and gas industry metering and control system — Remote gas well sites require local flow metering of the mineral reserve s gas flow rate for asset and revenue accounting purposes. Differential pressure flow meters are commonly used for this purpose.[1] Traditionally, local flow metering was… … Wikipedia
Liquid fuels — are those combustible or energy generating molecules that can be harnessed to create mechanical energy, usually producing kinetic energy; they also must take the shape of their container. Most liquid fuels, in widespread use, are or derived from… … Wikipedia
Oil shale extraction — is an industrial process in which kerogen mdash;a mixture of organic chemical compounds (including hydrocarbons) found in oil shale mdash;is converted into synthetic crude oil through pyrolysis. In pyrolysis, oil shale is heated in the absence of … Wikipedia
Liquid — is one of the principal states of matter. A liquid is a fluid that has the particles loose and can freely form a distinct surface at the boundaries of its bulk material. The surface is a free surface where the liquid is not constrained by a… … Wikipedia
oil painting — oil painter. 1. the art or technique of painting with oil colors. 2. a painting executed in oil colors. [1775 85] * * * Painting in oil colours, a medium consisting of pigments suspended in drying oils. Oil paint enables both fusion of tones and… … Universalium
Liquid-liquid extraction — Liquid liquid extraction, also known as solvent extraction and partitioning, is a method to separate compounds based on their relative solubilities in two different immiscible liquids, usually water and an organic solvent. It is an of a substance … Wikipedia