-
41 limiting value of the non-operating current in case of balanced load
предельное значение тока несрабатывания при равномерной нагрузке
-
[IEV number 442-05-64]EN
limiting value of the non-operating current in case of balanced load
Maximum value of current which, in the absence of any fault to frame or to earth, and of an earth leakage current, can flow in a circuit without any load unbalance, without causing operation of the part of the residual current device performing the evaluation.
[IEV number 442-05-64]FR
valeur limite du courant de non-fonctionnement en service équilibré
Valeur maximale du courant pouvant circuler dans un circuit, en l'absence de tout défaut à la masse ou à la terre et de tout courant de fuite à la terre en l'absence de tout déséquilibre de charge, sans provoquer le fonctionnement de la partie du dispositif de coupure différentiel assurant la fonction mesure.
[IEV number 442-05-64]EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > limiting value of the non-operating current in case of balanced load
-
42 limiting continuous current of an output circuit
предельный длительный ток выходной цепи электрического реле
Наибольшее значение тока, которое предварительно замкнутая или находящаяся в проводящем состоянии выходная цепь электрического реле способна выдерживать длительно в заданных условиях
[ ГОСТ 16022-83]Тематики
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > limiting continuous current of an output circuit
-
43 current limiting circuitbreaker
токоограничивающий автоматический выключатель
Выключатель с чрезвычайно малым временем отключения, в течение которого ток короткого замыкания не успевает достичь своего максимального значения.
[МЭК 60947-1]En
current-limiting circuit breaker
Circuit-breaker with a break-time short enough to prevent the short-circuit current reaching its otherwise attainable peak value.
[< size="2">IEC 60077-3, ed. 1.0 (2001-12)]
Circuit-breaker that, within a specified range of current, prevents the let-through current reaching the prospective peak value and which limits the let-through energy (I2t) to a value less than the let-through energy of a half-cycle wave of the symmetrical prospective current
NOTE 1 - Reference may be made to either the symmetrical or asymmetrical prospective peak value of let-through current.
NOTE 2 - The let-through current is also referred to as the cut-off current (see IEV 441-17-12).
NOTE 3 - Templates for the graphical representation of the cut-off current characteristic and the let-through energy characteristic are given in Figures K.2 to K.5 and examples of the use of the templates in Figures K.6 and K.7.
[IEC 60947-2, ed. 4.0, amd. 1 (2009-01)]Fr
disjoncteur limiteur de courant
Disjoncteur dont la durée de coupure est particulièrement brève en vue d’obtenir que le courant de court-circuit ne puisse atteindre son amplitude maximale
[< size="2">IEC 60077-3, ed. 1.0 (2001-12)]
Disjoncteur qui, à l'intérieur d'un domaine de courant spécifié, empêche le courant coupé limité d'atteindre la valeur crête présumée et qui limite l'énergie limitée (I2t) à une valeur inférieure à l'énergie limitée d'une demi-période du courant présumé symétrique
NOTE 1 Il peut être fait référence à la valeur crête présumée symétrique ou assymétrique du courant coupé limité.
NOTE 2 Le courant coupé limité (let-through current) est aussi nommé "cut-off current" (voir VEI 441-17-12).
NOTE 3 Les modèles de représentation graphique des caractéristiques de courant coupé limité et d'énergie limitée sont illustrés dans les Figures K.2 à K.5 et les exemples d'utilisation des modèles dans les Figures K.6 et K.7.
[IEC 60947-2, ed. 4.0, amd. 1 (2009-01)]Токоограничивающий автоматический выключатель имеет чрезвычайно малое время отключения, в течение которого ток КЗ не успевает достичь максимального значения.
Токоограничивающие автоматические выключатели ограничивают ток КЗ с помощью быстрого введения в цепь дополнительного сопротивления электрической дуги (в первый же полупериод, до того, как ток КЗ значительно возрастет) и последующего быстрого отключения КЗ, при этом ток КЗ не достигает ожидаемого расчетного максимального значения. Токоограничение начинается с некоторого значения тока, определяемого характеристикой токоогранияения.
В токоограничивающих автоматических выключателях при больших ожидаемых токах КЗ контакты, сразу же отбрасываются электродинамическими силами, вводя в цепь сопротивление дуги, и затем уже не соприкасаются, так как своевременно срабатывает электромагнитный расцепитель.
При малых токах КЗ контакты не отбрасываются, а отключение производится электромагнитным расцепителем.
[А.В.Беляев. Выбор аппаратуры, защит и кабелей в сетях 0,4 кВ. - Л.: Энергоатомиздат. 1988.]Тематики
Классификация
>>>Обобщающие термины
EN
- current limiting circuitbreaker
- current-limiting circuit breaker
- current-limiting circuit-breaker
- limiting circuit breaker
- limiting circuit-breaker
DE
FR
Англо-русский словарь нормативно-технической терминологии > current limiting circuitbreaker
-
44 band limiting
-
45 consequences limiting
English-Russian dictionary on nuclear energy > consequences limiting
-
46 current-limiting
токоограничивающий, токоограничительный - current-limiting circuit-breaker - current-limiting fuse - current-limiting reactorБольшой англо-русский и русско-английский словарь > current-limiting
-
47 current-limiting
1) токоограничивающий
2) токоограничительный
– current-limiting circuit-breaker
– current-limiting fuse
– current-limiting reactor -
48 current-limiting
-
49 assembly equipped with devices limiting internal arc effects
НКУ с устройствами ограничения воздействия внутренней дуги
-
[Интент]Параллельные тексты EN-RU
Assemblies equipped with devices limiting internal arc effects (active protection)
A design philosophy which is completely different from that just considered consists in guaranteeing the resistance to internal arcing by installing devices limiting the arc.
The approaches in that direction can be of two different types:
• limiting the destructive effects of the arc, once it has occured, by means of arc detectors
• limiting the destructive effects of the arc, once it has occured, by means of overpressure detectors.
The first possibility consists in installing in the assembly arc detectors which sense the light flux associated with the electric arc phenomenon.
Once the arc has been detected, these devices send an opening signal to the incoming circuit-breaker, thus guaranteeing tripping times of the order of 1-2 ms, therefore shorter than those proper of the circuit-breaker.
The operating logic of an arc detector is the following: the occurrence of an arc inside the switchboard is detected by the arc detector because an intense light radiation is associated with this phenomenon.
The arcing control system detects the event and sends a tripping signal to the circuit-breaker.
All the above with trip times of a few milliseconds and supplanting the tripping of the CB overcurrent relay which, for example, could be delayed due to current selectivity questions.
Figure 1 shows the possible positions where this device can be installed inside a switchboard.
The ideal solution is that which provides the installation of at least one detector for each column, with the consequent reduction to a minimum of the length of the optical fibers carrying the signal.
In order to prevent from an unwanted tripping caused by light sources indepent of the arc (lamps, solar radiation etc.), an additional current sensor is often positioned at the incoming of the main circuit-breaker.
Only in the event of an arc, both the incoming sensor which detects an “anomalous” current due to the arc fault as well as the sensor detecting the light radiation as sociated with the arc enable the system to intervene and allow the consequent opening of the circuit-breaker.
The second possibility consists in installing overpressure sensors inside the switchboard.
As previously described, the overpressure wave is one of the other effects occurring inside an assembly in case of arcing.
As a consequence it is possible to install some pressure sensors which are able to signal the pressure peak associated with the arc ignition with a delay of about 10-15 ms.
The signal operates on the supply circuit-breaker without waiting for the trip times of the selectivity protections to elapse, which are necessarily longer.
Such a system does not need any electronic processing device, since it acts directly on the tripping coil of the supply circuit-breaker.
Obviously it is essential that the device is set at fixed trip thresholds.
When an established internal overpressure is reached, the arc detector intervenes.
However, it is not easy to define in advance the value of overpressure generated by an arc fault inside a switchboard.
[ABB]НКУ с устройствами ограничения воздействия внутренней дуги (активная защита)
Для решения этой задачи используются совершенно другие, отличающиеся от ранее рассмотренных, принципы, заключающиеся в том, что противодействие внутренней дуге обеспечивается применением устройств, ограничивающих саму дугу.
Существует два типа решения проблемы в этом направлении:
• ограничение разрушающего воздействия дуги после того, как ее обнаружат специальные устройства
• ограничение разрушающего воздействия дуги после того, как специальные устройства обнаружат возникновение избыточного давления.
В первом случае в НКУ устанавливают устройства обнаружения дуги, реагирующие на световой поток, сопровождающий явление электрической дуги.
При обнаружении дуги данные устройства посылают сигнал управления на размыкание вводного автоматического выключателя. Гарантируемое время реакции составляет 1-2 мс, что меньше времени срабатывания автоматического выключателя.
Логика работы устройства обнаружения дуги следующая: Дуга, возникшая внутри НКУ, обнаруживается датчиком, реагирующим на интенсивное световое излучение, которым сопровождается горение дуги.
Обнаружив дугу, система управления посылает сигнал автоматическому выключателю.
Время срабатывания датчика и системы управления составляет несколько миллисекунд, что меньше времени срабатывания автоматического выключателя, осуществляющего защиту от сверхтока, который обычно для обеспечения требуемой селективности срабатывает с задержкой.
На рис. 1 показаны места возможной установки устройства защиты внутри НКУ.
Идеальным решением является установка, по крайней мере, одного устройства защиты в каждый шкаф многошкафного НКУ.
Это позволит до минимума сократить длину оптоволоконных кабелей передачи сигнала.
Для предотвращения ложного срабатывания от других источников света (т. е. не от дуги), например, таких как лампы, солнечное излучение и т. п., дополнительно в главной цепи вводного автоматического выключателя устанавливают датчик тока.
Только при наличии двух событий, а именно: срабатывания датчика света и обнаружения аномального увеличения тока, система управления считает, что возникла электрическая дуга и подает команду на отключение вводного автоматического выключателя.
Второе решение заключается в установке внутри НКУ датчика избыточного давления.
Как было описано ранее, одним из характерных проявлений электрической дуги, возникшей внутри НКУ, является ударная волна.
Это означает, что можно установить несколько датчиков давления, задачей которых является обнаружение импульса давления (с задержкой 10…15 мс), обусловленного зажиганием дуги.
Сигнал от датчиков давления поступает на вводной автоматический выключатель, который срабатывает без задержки на обеспечение селективности.
Такая система не нуждается в электронном устройстве обработки информации, поскольку воздействует непосредственно на независимый расцепитель автоматического выключателя.
Вполне понятно, что такое устройство имеет фиксированный порог срабатывания.
Датчик-реле дуги сработает, как только будет достигнуто заданное значение избыточного давления.
Следует иметь в виду, что не так легко заранее определить значение избыточного давления, которое будет создано при зажигании дуги внутри НКУ.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
EN
Англо-русский словарь нормативно-технической терминологии > assembly equipped with devices limiting internal arc effects
-
50 conditional short-circuit current (of a circuit or a switching device)
условный ток короткого замыкания (в цепи или коммутационном аппарате)
Ожидаемый ток, который цепь или коммутационнный аппарат, защищенные установленным устройством от коротких замыканий, способны удовлетворительно выдерживать в течение всего времени срабатывания этого устройства в указанных условиях эксплуатации и поведения.
Примечания
1 В настоящем стандарте устройством для защиты от коротких замыканий служит, как правило, автоматический выключатель или плавкие предохранители.
2 Это определение отличается от МЭК 60050(441-17-20) расширением понятия токоограничивающего аппарата до устройства для защиты от коротких замыканий, функция которого не сводится только к токоограничению.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
conditional short-circuit current (of a circuit or a switching device)
the prospective current that a circuit or a switching device, protected by a specified current limiting device, can satisfactorily withstand for the operating time of that current limiting device under specified conditions of use and behaviour
[IEV number 441-17-20]FR
courant de court-circuit conditionnel (d'un circuit ou d'un appareil de connexion)
courant présumé qu'un circuit ou un appareil de connexion, protégé par un dispositif limiteur de courant spécifié, peut supporter de façon satisfaisante pendant la durée de fonctionnement de cet appareil limiteur de courant dans des conditions spécifiées d'emploi et de comportement
[IEV number 441-17-20]Тематики
- выключатель автоматический
- выключатель, переключатель
- предохранитель
- электротехника, основные понятия
EN
DE
FR
- courant de court-circuit conditionnel (d'un circuit ou d'un appareil de connexion)
Англо-русский словарь нормативно-технической терминологии > conditional short-circuit current (of a circuit or a switching device)
-
51 short-time withstand current of an output circuit (deprecated)
предельный кратковременный ток выходной цепи
-
[IEV number 445-04-01]EN
limiting short-time current of an output circuit
short-time withstand current of an output circuit (deprecated)
highest value of electric current which a closed contact or an effectively conducting output circuit is capable of carrying for a specified short period under specified conditions
[IEV number 445-04-01]FR
courant limite de courte durée d'un circuit de sortie, m
valeur la plus élevée du courant électrique qu'un contact fermé ou un circuit de sortie à l'état passant est capable de supporter dans des conditions spécifiées et pendant une courte durée spécifiée
[IEV number 445-04-01]Тематики
- электротехника, основные понятия
EN
- limiting short-time current of an output circuit
- short-time withstand current of an output circuit (deprecated)
DE
FR
Англо-русский словарь нормативно-технической терминологии > short-time withstand current of an output circuit (deprecated)
-
52 overvoltage category (of a circuit or within an electrical system)
категория перенапряжения (в цепи или электрической системе)
Условное число, основанное на ограничении (или регулировании) значений ожидаемого переходного перенапряжения, возникающего в цепи (или в электрической системе с различными номинальными напряжениями), зависящее от способов воздействия на перенапряжения.
Примечание. В электрической системе переход от одной категории перенапряжения к другой, более низкой, достигается средствами, совместимыми с требованиями к переходным участкам, например с помощью устройства для защиты от перенапряжений или последовательно-параллельного присоединения импеданса, способного рассеять, поглотить или отклонить энергию соответствующего импульсного тока с целью снижения переходного перенапряжения до желательно меньшей категории перенапряжения.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
категория перенапряжения
Категория электротехнического оборудования по стойкости изоляции к импульсным перенапряжениям (всего четыре категории: I, II, III, IV)
[Интент]EN
overvoltage category (of a circuit or within an electrical system)
conventional number based on limiting (or controlling) the values of prospective transient overvoltages occurring in a circuit (or within an electrical system having different nominal voltages) and depending upon the means employed to influence the overvoltages
NOTE In an electrical system, the transition from one overvoltage category to another of lower category is obtained through appropriate means complying with interface requirements, such as an overvoltage protective device or a series-shunt impedance arrangement capable of dissipating, absorbing, or diverting the energy in the associated surge current, to lower the transient overvoltage value to that of the desired lower overvoltage category
[IEC 60947-1, ed. 5.0 (2007-06)]FR
catégorie de surtension (d'un circuit ou dans un réseau)
nombre conventionnel, basé sur la limitation (ou la commande) des valeurs des surtensions transitoires présumées apparaissant dans un circuit (ou dans un réseau où existent des sections de tensions nominales différentes) et dépendant des moyens employés pour agir sur ces surtensions
NOTE Dans un réseau, le passage d'une catégorie de surtension à une autre de catégorie inférieure est réalisé à l'aide de moyens appropriés répondant aux prescriptions d'interface, tels qu'un dispositif de protection contre les surtensions ou des impédances disposées en séries et/ou en parallèle capables de dissiper, d'absorber ou de détourner l'énergie du courant de surcharge correspondant, afin d'abaisser la valeur des surtensions transitoires à celle qui correspond à la catégorie de surtension inférieure recherchée
[IEC 60947-1, ed. 5.0 (2007-06)]Требуемая стойкость к импульсным напряжениям, кВ:
-
Оборудования на вводе в установку ( IV категория перенапряжения)
-
Оборудования распределительных и конечных цепей ( III категория перенапряжения)
-
Электробытовых приборов и электроприемников ( II категория перенапряжения)
-
Специально защищенного оборудования ( I категория перенапряжения)
[ ГОСТ Р 50571-4-44-2011( МЭК 60364-4-44: 2007) ]
Тематики
- электротехника, основные понятия
EN
- overvoltage categories
- overvoltage category (of a circuit or within an electrical system)
- overvoltage withstand categories
- surge voltage category
FR
Англо-русский словарь нормативно-технической терминологии > overvoltage category (of a circuit or within an electrical system)
-
Оборудования на вводе в установку ( IV категория перенапряжения)
-
53 integrated circuit resistor
pull-down resistor — согласующий резистор; резистор утечки
etched resistor — резистор, полученный методом травления
The English-Russian dictionary general scientific > integrated circuit resistor
-
54 current-limiting automatic circuit breaker
Автоматика: токоограничивающий автоматический выключательУниверсальный англо-русский словарь > current-limiting automatic circuit breaker
-
55 current-limiting miniature circuit breaker
Универсальный англо-русский словарь > current-limiting miniature circuit breaker
-
56 current-limiting automatic circuit breaker
English-Russian dictionary of mechanical engineering and automation > current-limiting automatic circuit breaker
-
57 cascading
- резервная защита
- перекрытие по поверхности гирлянды ЛЭП
- каскадный паровой нагрев
- каскадирование
- включение ступенями
включение ступенями
каскадное включение
многошаговый
многоуровневый
каскадный
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]Тематики
Синонимы
EN
каскадирование
-Параллельные тексты EN-RU
Cascading originates from current-limiting technology.
If limiting breaking/making capacity of a circuit breaker is lower than prospective short-circuit current, it can be installed downstream of a current-limiting circuit breaker so that it can have improved breaking capacity due to current-limiting ability of the upstream circuit breaker.
Cascading technology helps lower cost of downstream switches and accessories.
[Schneider Electric]Принцип каскадирования основан на применении технологии токоограничения.
Если предельная отключающая/включающая способность автоматического выключателя ниже ожидаемого тока короткого замыкания, то его можно установить со стороны нагрузки при условии, что со стороны источника питания установлен токоограничивающий автоматический выключатель. Таким образом, отключающая способность выключателя со стороны нагрузки увеличивается за счет токоограничения выключателя, расположенного со стороны источника питания.Метод каскадирования позволяет применять более дешевые принадлежности и аппараты, включаемые со стороны нагрузки.
[Перевод Интент]Тематики
- выключатель автоматический
- предохранитель
- электротехника, основные понятия
EN
каскадный паровой нагрев
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
перекрытие по поверхности гирлянды ЛЭП
—
[А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]Тематики
EN
резервная защита
Координация по сверхтокам двух устройств для защиты от сверхтоков, соединенных последовательно, когда защитное устройство, расположенное, как правило, но необязательно на входной стороне, осуществляет защиту от сверхтока с помощью или без помощи второго защитного устройства, предотвращая его чрезмерную нагрузку.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]Параллельные тексты EN-RU Cascading or back-up protection
This consists of installing an upstream circuit-breaker D1 to help a downstream circuit-breaker D2 to break short-circuit currents greater than its ultimate breaking capacity lcuD2.
This value is marked lcuD2+D1.
Standard IEC 60947-2 recognises cascading between two circuit-breakers.
[Schneider Electric]Резервная защита
Смысл резервной защиты состоит в том, что расположенный выше автоматический выключатель D1 помогает расположенному ниже автоматическому выключателю D2 отключать токи короткого замыкания, превышающие предельную отключающую способность lcuD2.
Это значение обозначают lcuD2+D1.
Координация характеристик двух автоматических выключателей, реализуемая по принципу резервной защиты рассмотрена в стандарте МЭК 60947-2.
[Перевод Интент]
Рис. Schneider ElectricТематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > cascading
-
58 cascading method
каскадирование
-Параллельные тексты EN-RU
Cascading originates from current-limiting technology.
If limiting breaking/making capacity of a circuit breaker is lower than prospective short-circuit current, it can be installed downstream of a current-limiting circuit breaker so that it can have improved breaking capacity due to current-limiting ability of the upstream circuit breaker.
Cascading technology helps lower cost of downstream switches and accessories.
[Schneider Electric]Принцип каскадирования основан на применении технологии токоограничения.
Если предельная отключающая/включающая способность автоматического выключателя ниже ожидаемого тока короткого замыкания, то его можно установить со стороны нагрузки при условии, что со стороны источника питания установлен токоограничивающий автоматический выключатель. Таким образом, отключающая способность выключателя со стороны нагрузки увеличивается за счет токоограничения выключателя, расположенного со стороны источника питания.Метод каскадирования позволяет применять более дешевые принадлежности и аппараты, включаемые со стороны нагрузки.
[Перевод Интент]Тематики
- выключатель автоматический
- предохранитель
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > cascading method
-
59 cascading technology
каскадирование
-Параллельные тексты EN-RU
Cascading originates from current-limiting technology.
If limiting breaking/making capacity of a circuit breaker is lower than prospective short-circuit current, it can be installed downstream of a current-limiting circuit breaker so that it can have improved breaking capacity due to current-limiting ability of the upstream circuit breaker.
Cascading technology helps lower cost of downstream switches and accessories.
[Schneider Electric]Принцип каскадирования основан на применении технологии токоограничения.
Если предельная отключающая/включающая способность автоматического выключателя ниже ожидаемого тока короткого замыкания, то его можно установить со стороны нагрузки при условии, что со стороны источника питания установлен токоограничивающий автоматический выключатель. Таким образом, отключающая способность выключателя со стороны нагрузки увеличивается за счет токоограничения выключателя, расположенного со стороны источника питания.Метод каскадирования позволяет применять более дешевые принадлежности и аппараты, включаемые со стороны нагрузки.
[Перевод Интент]Тематики
- выключатель автоматический
- предохранитель
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > cascading technology
-
60 breaker
1) выключатель2) абонент системы персональной радиосвязи, пытающийся передать сообщение по занятому каналу•- automatic reclosing circuit breaker
- automatic tripping circuit breaker
- circuit breaker
- contact breaker
- current limiting circuit breaker
- deion circuit breaker
- double-throw breaker
- double-throw circuit breaker
- field circuit breaker
- gas-blast circuit breaker
- magnetic circuit breaker
- mercury breaker
- oil circuit breaker
- overvoltage tripping circuit breaker
- reverse power tripping circuit breaker
- series overcurrent tripping circuit breaker
- series undercurrent tripping circuit breaker
- shunt tripping circuit breaker
- single-throw breaker
- single-throw circuit breaker
- thermal circuit breaker
- transformer overcurrent tripping circuit breaker
- transformer undercurrent tripping circuit breaker
- trip-free circuit breaker
- undervoltage tripping circuit breaker
См. также в других словарях:
current-limiting circuit breaker — ribinės srovės išjungiklis statusas T sritis radioelektronika atitikmenys: angl. current limiting circuit breaker vok. Strombegrenzungsschalter, m rus. токоограничивающий выключатель, m pranc. disjoncteur limiteur de courant, m … Radioelektronikos terminų žodynas
Circuit total limitation — (CTL) is one of the present day standards for electrical panels sold in the United States according to the National Electrical Code. The 1965 edition of the NEC, article 384 15 was the first reference to the circuit total limitation of… … Wikipedia
Circuit de la Sarthe — For the French road bicycle racing stage race, see Circuit de la Sarthe (cycling) Circuit des 24 Heures Circuit de la Sarthe Location Le Mans, France … Wikipedia
Current limiting — is the practice in electrical or electronic circuits of imposing an upper limit on the current that may be delivered to a load with the purpose of protecting the circuit generating or transmitting the current from harmful effects due to a short… … Wikipedia
Snetterton Motor Racing Circuit — Motorsport venue Name = Snetterton Race Circuit | Location = Norfolk, England Events = British Touring Car Championship, British F3, British Superbikes Length km = 3.123 Length mi = 1.952 Turns = 7 Record time = 0:56.095 Record driver= Klaas… … Wikipedia
LED circuit — In electronics, the basic LED circuit is an electrical circuit used to power a light emitting diode (LED). It consists of up to four components connected in series: a voltage source, a current limiting resistor, an LED, and optionally a switch to … Wikipedia
Magnetic circuit — Magnetic Circuits Conventional Magnetic Circuits Magnetomotive force Magnetic flux Φ Magnetic reluctance Phasor Magnetic Circuits Complex reluctance Zμ … Wikipedia
Crystal Palace (circuit) — Crystal Palace circuit Location London, United Kingdom Major events Formula One Formula Two London Grand Prix BTCC British F3 Sports car racing Length 3 km (2 mi) Lap record at 103.39 mph ( … Wikipedia
Regenerative circuit — The regenerative circuit (or self regenerative circuit) allows an electronic signal to be amplified many times by the same vacuum tube or other active component such as a field effect transistor.Description Regenerative circuits were employed in… … Wikipedia
Crowbar (circuit) — A crowbar circuit is an electrical circuit used to prevent an overvoltage condition of a power supply unit from damaging the circuits attached to the power supply. It operates by putting a short circuit or low resistance path across the voltage… … Wikipedia
Application-specific integrated circuit — An application specific integrated circuit (ASIC) is an integrated circuit (IC) customized for a particular use, rather than intended for general purpose use. For example, a chip designed solely to run a cell phone is an ASIC.In contrast, the… … Wikipedia