-
1 ток мгновенного расцепления
ток мгновенного расцепления Ii
Значение тока, выше которого автоматический выключатель для электрооборудования должен автоматически сработать (без намеренной выдержки времени) в течение менее 0,1 с.
[ ГОСТ Р 50031-99( МЭК 60934-93)]
ток мгновенного расцепления
Минимальное значение тока, вызывающее срабатывание выключателя без выдержки времени
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
instantaneous tripping current (of a circuit-breaker)
the value of current above which the circuit-breaker will operate automatically without intentional time-delay
[IEV number 442-05-46]FR
courant de déclenchement instantané (d'un disjoncteur)
Примечание
valeur du courant au-dessus de laquelle le fonctionnement automatique d'un disjoncteur a lieu sans temporisation intentionnelle
[IEV number 442-05-46]
Более подробно о токе мгновенного расцепления см. " защитная характеристика автоматического выключателя"
Параллельные тексты EN-RUIn addition, the core loss decreases attractive force, which leads to increase of instantaneous trip current.
[LS Industrial Systems]Кроме того, потери в магнитной системе уменьшают силу притяжения, что приводит к увеличению тока мгновенного расцепления.
[Перевод Интент]Тематики
Синонимы
- Ii
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ток мгновенного расцепления
-
2 мгновенный ток нерасцепления
мгновенный ток нерасцепления Ini
-
[IEV number 442-05-56 ]EN
instantaneous non-tripping current
the value of current below which the circuit-breaker will not operate automatically without intentional time-delay
[IEV number 442-05-56 ]FR
courant de non-déclenchement instantané
valeur du courant en dessous de laquelle le fonctionnement automatique du disjoncteur sans temporisation intentionnelle n'a pas lieu
[IEV number 442-05-56 ]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > мгновенный ток нерасцепления
-
3 ток мгновенного нерасцепления Ini
ток мгновенного нерасцепления Ini
Значение тока, ниже которого автоматический выключатель для электрооборудования не должен автоматически сработать (без намеренной выдержки времени) в течение времени, равного или меньшего 0,1 с.
[ ГОСТ Р 50031-99( МЭК 60934-93)]EN
instantaneous non-tripping current
the value of current below which the circuit-breaker will not operate automatically without intentional time-delay
[IEV number 442-05-56]FR
courant de non-déclenchement instantané
valeur du courant en dessous de laquelle le fonctionnement automatique du disjoncteur sans temporisation intentionnelle n'a pas lieu
[IEV number 442-05-56]Тематики
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ток мгновенного нерасцепления Ini
-
4 входное полное сопротивление
входное полное сопротивление
-
[IEV number 312-06-18]EN
input impedance
impedance of the input circuit measured between the input terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the input circuit is such that the instantaneous value of the current flowing into the input terminals is a non-linear function of the instantaneous value of the input voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual input circuit, is sometimes called the "equivalent input impedance".
[IEV number 312-06-18]FR
impédance du circuit d'entrée
impédance du circuit d'entrée entre les bornes d'entrée dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit d'entrée est tel que la valeur instantanée du courant traversant les bornes d'entrée est une fonction non linéaire de la valeur instantanée de la tension d'entrée dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit d'entrée réel, est parfois appelée "impédance équivalente d'entrée".
[IEV number 312-06-18]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > входное полное сопротивление
-
5 выходное полное сопротивление
выходное полное сопротивление
-
[IEV number 312-06-19]EN
output impedance
impedance of the output circuit measured between the output terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the output circuit is such that the instantaneous value of the current flowing into the output terminals is a non-linear function of the instantaneous value of the output voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual output circuit, is sometimes called the "equivalent output impedance".
[IEV number 312-06-19]FR
impédance du circuit de sortie
impédance du circuit de sortie entre les bornes de sortie dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit de sortie est tel que la valeur instantanée du courant traversant les bornes de sortie est une fonction non linéaire de la valeur instantanée de la tension de sortie dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit de sortie réel, est parfois appelée "impédance équivalente de sortie".
[IEV number 312-06-19]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выходное полное сопротивление
-
6 ожидаемый пиковый ток
ожидаемый пиковый ток
Пиковое значение ожидаемого тока в переходный период после его появления.
Примечание. Это определение подразумевает, что ток включается идеальным коммутационным аппаратом, т. е. с мгновенным переходом от бесконечного к нулевому значению полного сопротивления. Для цепей, в которых ток может проходить по нескольким различным путям, например многофазных цепей, предполагается также, что ток включается одновременно во всех полюсах, даже если рассматривается ток только в одном полюсе.
МЭК 60050(441-17-02).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
prospective peak current
the peak value of a prospective current during the transient period following initiation
NOTE – The definition assumes that the current is made by an ideal switching device, i.e. with instantaneous transition from infinite to zero impedance. For circuits where the current can follow several different paths, e.g. polyphase circuits, it further assumes that the current is made simultaneously in all poles, even if only the current in one pole is considered.
[IEV number 441-17-02]FR
valeur de crête du courant présumé
valeur de crête d'un courant présumé pendant la période transitoire qui suit son établissement
NOTE – La définition implique que le courant est établi par un appareil de connexion idéal, c'est-à-dire passant instantanément d'une impédance infinie à une impédance nulle. Pour un circuit ayant plusieurs voies, par exemple un circuit polyphasé, il est entendu en outre que le courant est établi simultanément dans tous les pôles même si on ne considère que le courant dans un seul pôle.
[IEV number 441-17-02]Тематики
- выключатель автоматический
- выключатель, переключатель
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ожидаемый пиковый ток
-
7 ток отсечки
ток отсечки
Максимальное мгновенное значение тока, достигаемое в процессе отключения тока коммутационным аппаратом или плавким предохранителем.
МЭК 60050 (441-17-12).
Примечание. Понятие особенно важно, когда коммутационный аппарат или плавкий предохранитель срабатывает так, что ожидаемый пиковый ток цепи не достигается.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
cut-off current
let-through current
the maximum instantaneous value of current attained during the breaking operation of a switching device or a fuse
NOTE – This concept of particular importance when the switching device or the fuse operates in such a manner that the prospective peak current of the circuit is not reached.
[IEV number 441-17-12]FR
courant coupé limité
valeur instantanée maximale du courant atteinte au cours de la coupure effectuée par un appareil de connexion ou un fusible
NOTE – Cette notion est d'importance particulière si l'appareil de connexion ou le fusible fonctionne de telle manière que la valeur de crête du courant présumé du circuit n'est pas atteinte.
[IEV number 441-17-12]Примечание
Более подробно о токе отсечки см. " защитная характеристика автоматического выключателя"Тематики
- выключатель автоматический
- выключатель, переключатель
- предохранитель
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ток отсечки
-
8 автоматический выключатель
автоматический выключатель
Механический коммутационный аппарат1), способный включать, проводить и отключать токи при нормальном состоянии электрической цепи, а также включать, проводить в течение заданного времени и автоматически отключать токи в указанном аномальном состоянии электрической цепи, например, при коротком замыкании.
(МЭС 441-14-20)
[ ГОСТ Р 50030. 2-99 ( МЭК 60947-2-98)]
автоматический выключатель
-
[IEV number 442-05-01]EN
circuit breaker
a mechanical switching device, capable of making, carrying and breaking currents under normal circuit conditions and also making, carrying for a specified time and breaking currents under specified abnormal circuit conditions such as those of short circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
circuit breaker
A device designed to open and close a circuit by nonautomatic means and to open the circuit automatically on a predetermined overcurrent without damage to itself when properly applied within its rating.
NOTE The automatic opening means can be integral, direct acting with the circuit breaker, or remote from the circuit breaker.
Adjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker can be set to trip at various values of current, time, or both within a predetermined range. Instantaneous-trip (as applied to circuit breakers). A qualifying term indicating that no delay is purposely introduced in the tripping action of the circuit breaker.
Inverse-time (as applied to circuit breakers). A qualifying term indicating a delay is purposely introduced in the tripping action of the circuit breaker, which delay decreases as the magnitude of the current increases.
Nonadjustable (as applied to circuit breakers). A qualifying term indicating that the circuit breaker does not have any adjustment to alter the value of current at which it will trip or the time required for its operation.
Setting (of a circuit breaker). The value of current, time, or both at which an adjustable circuit breaker is set to trip.
[National Electrical Cod]FR
disjoncteur
1) Должно быть контактный коммутационный аппарат
appareil mécanique de connexion capable d’établir, de supporter et d’interrompre des courants dans les conditions normales du circuit, ainsi que d’établir, de supporter pendant une durée spécifiée et d’in- terrompre des courants dans des conditions anormales spécifiées du circuit telles que celles du court-circuit.
[IEC 62271-100, ed. 2.0 (2008-04)]
[IEV number 442-05-01]
[Интент]КЛАССИФИКАЦИЯ
- По роду тока
- По напряжению
- По числу полюсов
- По виду корпуса
- По месту установки
- По изолирующей среде
- По установленным расцепителям
- По дополнительным защитам
- По назначению
- По категории применения
- По виду привода взвода пружины
- По выполняемой функции
-
По влиянию монтажного положения
Автоматические выключатели ABB Модульные автоматические выключатели
1. НЕКОТОРЫЕ СВЕДЕНИЯ ОБ АВТОМАТИЧЕСКИХ ВЫКЛЮЧАТЕЛЯХ Автоматический выключатель — это электрический аппарат, который автоматически отключает (и тем самым защищает) электрическую цепь при возникновении в ней аномального режима. Режим становится аномальным, когда в цепи начинает недопустимо изменяться (т. е. увеличиваться или уменьшаться относительно номинального значения) ток или напряжение.
Другими словами (более "инженерно") можно сказать, что автоматический выключатель защищает от токов короткого замыкания и токов перегрузки отходящую от него питающую линию, например, кабель и приемник(и) электрической энергии (осветительную сеть, розетки, электродвигатель и т. п.).
Как правило, автоматический выключатель может применятся также для нечастого (несколько раз в сутки) включения и отключения защищаемых электроприемников (защищаемой нагрузки).
[Интент]Выключатель предназначен для проведения тока в нормальном режиме и отключения тока при коротких замыканиях, перегрузках, недопустимых снижениях напряжения, а также до 30 оперативных включений и отключений электрических цепей в сутки и рассчитан для эксплуатации в электроустановках с номинальным рабочим напряжением до 660 В переменного тока частоты 50 и 60 Гц и до 440 В постоянного тока.
[Типовая фраза из российской технической документации] 2. ПРИНЦИП ДЕЙСТВИЯ Для защиты цепи от короткого замыкания применяется автоматический выключатель с электромагнитным расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Автоматический выключатель устроен таким образом, что сначала необходимо взвести пружину и только после этого его можно включить. У многих автоматических выключателей для взвода пружины необходимо перевести ручку вниз. После этого ручку переводят вверх. При этом замыкаются главные контакты.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Электромагнитный расцепитель;
5 - Сердечник
6 - Катушка
7 - Контактные зажимы автоматического выключателя
На рисунке показан один полюс автоматического выключателя во включенном положении: пружина 1 взведена, а главный контакт 2 замкнут.
Как только в защищаемой цепи возникнет короткое замыкание, ток, протекающий через соответствующий полюс автоматического выключателя, многократно возрастет. В катушке 6 сразу же возникнет сильное магнитное поле. Сердечник 5 втянется в катушку и освободит удерживающее устройство. Под действием пружины 1 главный контакт 2 разомкнется, в результате чего автоматический выключатель отключит и тем самым защитит цепь, в которой возникло короткое замыкание. Такое срабатывание автоматического выключателя происходит практически мгновенно (за сотые доли секунды).
Для защиты цепи от тока перегрузки применяют автоматические выключатели с тепловым расцепителем.1 - Пружина (в данном случае во взведенном положении растянута)
Принцип действия такой же как и в первом случае, с той лишь разницей, что удерживающее устройство 3 освобождается под действием биметаллической пластины 5, которая изгибается от тепла, выделяемого нагревательным элементом 6. Количество тепла определяется током, протекающим через защищаемую цепь.
2 - Главный контакт автоматического выключателя
3 - Удерживающее устройство
4 - Тепловой расцепитель
5 - Биметаллическая пластина
6 - Нагревательный элемент
7 - Контактные зажимы автоматического выключателя
[Интент]Недопустимые, нерекомендуемые
Тематики
Классификация
>>>Обобщающие термины
Действия
- включение автоматического выключателя
- оперирование автоматического выключателя
- отключение автоматического выключателя
- срабатывание автоматического выключателя
EN
- auto-cutout
- automatic circuit breaker
- automatic cutout
- automatic switch
- breaker
- CB
- circuit breaker
- circuit-breaker
- cutout
DE
FR
Смотри также
Русско-французский словарь нормативно-технической терминологии > автоматический выключатель
9 ожидаемое восстанавливающееся напряжение (цепи)
ожидаемое восстанавливающееся напряжение (цепи)
Напряжение после отключения ожидаемого симметричного тока идеальным коммутационным аппаратом.
Примечание. Определение подразумевает, что коммутационный аппарат или плавкий предохранитель, для которого оценивается ожидаемое восстанавливающее напряжение, заменен идеальным коммутационным аппаратом, т. е. с мгновенным переходом от нулевого к бесконечному полному сопротивлению в самый момент уменьшения тока до нуля, т. е. при «естественном» нуле. Для цепей, в которых ток может проходить по нескольким различным путям, например для многофазной цепи, это определение подразумевает также, что ток отключается идеальным коммутационным аппаратом только в рассматриваемом полюсе.
МЭК 60050(441-17-29)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
prospective transient recovery voltage (of a circuit)
the transient recovery voltage following the breaking of the prospective symmetrical current by an ideal switching device
NOTE – The definition assumes that the switching device or the fuse, for which the prospective transient recovery voltage is sought, is replaced by an ideal switching device, i.e. having instantaneous transition from zero to infinite impedance at the very instant of zero current, i.e. at the "natural" zero. For circuits where the current can follow several different paths, e.g. a polyphase circuit, the definition further assumes that the breaking of the current by the ideal switching device takes place only in the pole considered.
[IEV number 441-17-29]FR
tension transitoire de rétablissement présumée (d'un circuit)
tension transitoire de rétablissement qui suit la coupure du courant présumé symétrique par un appareil de connexion idéal
NOTE – La définition implique que l'appareil de connexion ou le fusible, pour lequel la tension transitoire de rétablissement est recherchée, est remplacé par un appareil de connexion idéal, c'est-à-dire dont l'impédance passe instantanément de la valeur zéro à la valeur infinie à l'instant du zéro de courant, c'est-à-dire au zéro "naturel". Pour des circuits ayant plusieurs voies, par exemple un circuit polyphasé, on suppose en outre que la coupure du courant par l'appareil de connexion idéal n'a lieu que sur le pôle considéré.
[IEV number 441-17-29]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ожидаемое восстанавливающееся напряжение (цепи)
10 двустабильное электрическое реле
двустабильное электрическое реле
Электрическое реле, которое, изменив свое состояние под воздействием входной воздействующей или характеристической величины, после устранения воздействия не изменяет своего состояния до приложения другого необходимого воздействия
[ ГОСТ 16022-83]EN
bistable relay
electrical relay which, having responded to an energizing quantity and having changed its condition, remains in that condition after the quantity has been removed; a further appropriate energization is required to make it change its condition
[IEV number 444-01-08]FR
relais bistable, m
relais électrique qui, ayant changé d'état sous l'action d'une grandeur d'alimentation d'entrée, reste dans le même état lorsqu'on supprime cette grandeur ; une autre action appropriée est nécessaire pour le faire changer d'état
[IEV number 444-01-08]Параллельные тексты EN-RU
In a bistable relay with one winding, the opposite energizing is created by a voltage with opposite polarity being applied to the same winding.
In a bistable relay with two windings, the opposing energizing is created by a voltage being applied to the second winding with opposite winding sense.
[Tyco Electronics]В двустабильном реле с одной обмоткой изменение коммутационного положения осуществляется подачей напряжения противоположной полярности на эту же самую обмотку.
В двустабильном реле с двумя обмотками изменение коммутационного положения осуществляется подачей напряжения на другую обмотку (т. е. на обмотку, действие которой противоположно действию предыдущей обмотки).
[Перевод Интент]A remanent, bistable relay which adopts a particular switching position following an energizing direct current in any direction and is then held in this position by the remanence in the magnetic circuit, i.e. through the magnetization of parts of the magnetic circuit. The contacts return to their original position following a small energizing current of limited amplitude of the opposite polarity. This demagnetises the magnetic circuit.
[Tyco Electronics]Двустабильное реле с остаточной намагниченностью переходит в определенное коммутационное положение при подаче постоянного тока любой полярности и затем удерживается в этом положении за счет остаточной намагниченности частей магнитопровода. Контакты реле возвращаются в исходное положение после воздействия небольшого тока обратной полярности. При этом происходит размагничивание магнитопровода.
[Перевод Интент]Недопустимые, нерекомендуемые
- бистабильное реле
- реле с механической блокировкой
- реле с самоудерживанием
- реле самозамыкающее
- реле самоудерживающее
Тематики
Классификация
>>>EN
DE
FR
14. Двустабильное электрическое реле
D. Bistabiles Relais
Е. Bistable relay
F. Relais bistable
Электрическое реле, которое, изменив свое состояние под воздействием входной воздействующей или характеристической величины, после устранения воздействия не изменяет своего состояния до приложения другого необходимого воздействия
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > двустабильное электрическое реле
11 water
*См. также в других словарях:
instantaneous current — akimirkinė srovė statusas T sritis automatika atitikmenys: angl. instantaneous current vok. Augenblicksstrom, m; Augenblickswert des Stromes, m; Momentanstrom, m rus. мгновенный ток, m pranc. courant instantané, m; courant momentané, m ryšiai:… … Automatikos terminų žodynas
instantaneous current — akimirkinė srovė statusas T sritis Standartizacija ir metrologija apibrėžtis Elektros srovės stipris tam tikrą akimirką. atitikmenys: angl. instantaneous current vok. Augenblicksstrom, m; Augenblickswert des Stromes, m rus. мгновенный ток, m… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
instantaneous current — momentinė srovė statusas T sritis chemija apibrėžtis Elektros srovė, registruojama fiksuotu laiko momentu. atitikmenys: angl. instantaneous current rus. мгновенный ток ryšiai: sinonimas – akimirkinė srovė … Chemijos terminų aiškinamasis žodynas
instantaneous current — akimirkinė srovė statusas T sritis fizika atitikmenys: angl. instantaneous current vok. Augenblicksstrom, m rus. мгновенный ток, m pranc. courant instantané, m … Fizikos terminų žodynas
Current clamp — For current clamp recording in neurons, see Electrophysiology#Current clamp. In electrical and electronic engineering, a current clamp or current probe is an electrical device having two jaws which open to allow clamping around an electrical… … Wikipedia
Alternating current — (green curve). The horizontal axis measures time; the vertical, current or voltage. In alternating current (AC, also ac) the movement of electric charge periodically reverses direction. In direct current (DC, also dc), the flow of electric charge … Wikipedia
Residual-current device — A two pole residual current device A Residual Current Device is a generic term covering both RCCBs and RCBOs. A Residual Current Circuit Breaker (RCCB) is an electrical wiring device that disconnects a circuit whenever it detects that the… … Wikipedia
Inrush current — or input surge current refers to the maximum, instantaneous input current drawn by an electrical device when first turned on. For example, incandescent light bulbs have high inrush currents until their filaments warm up and their resistance… … Wikipedia
Acoustic Doppler Current Profiler — Head of an ADCP with the four transducers ADCP view ahead, mo … Wikipedia
effective current — noun : the value of an alternating or otherwise variable current that would result in the same heat production in a circuit as that of a direct current in the same length of time : the square root of the means of the squares of the instantaneous… … Useful english dictionary
Electricity meter — Typical North American domestic analog electricity meter … Wikipedia
Перевод: со всех языков на французский
с французского на все языки- С французского на:
- Все языки
- Со всех языков на:
- Все языки
- Английский
- Арабский
- Болгарский
- Вьетнамский
- Испанский
- Немецкий
- Нидерландский
- Русский
- Тамильский
- Турецкий
- Украинский
- Финский
- Французский