-
1 Free-Flow-System
сущ. -
2 Free-Flow-System
nтанкер с безнапорным ( свободным) заполнением танков ( через кормовые танки)Deutsch-Russische Wörterbuch polytechnischen > Free-Flow-System
-
3 Free-Flow-System
n танкер м. с безнапорным заполнением танковNeue große deutsch-russische Wörterbuch Polytechnic > Free-Flow-System
-
4 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
5 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
6 Herzkreislaufsystem
сердечно-сосудистая система
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
cardiovascular system
Those structures, including the heart and blood vessels, which provide channels for the flow of blood. (Source: MGH)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Herzkreislaufsystem
-
7 FFMS
-
8 Lichtbogenlöschung
гашение дуги
-
[Интент]Параллельные тексты EN-RU
The gas flow required for arc-quenching is produced in the switching system by means of self compression.
[Siemens]Струя элегаза, необходимая для гашения дуги в дугогасительной камере, создается в процессе автокомпрессии.
[Перевод Интент]Тематики
- высоковольтный аппарат, оборудование...
- электротехника, основные понятия
Синонимы
EN
DE
Немецко-русский словарь нормативно-технической терминологии > Lichtbogenlöschung
-
9 Fehler durch Kurzschluss, m
поперечное повреждение
поперечное замыкание
Повреждение, которое характеризуется прохождением тока с частотой сети между двумя или более фазами или между фазой (фазами) и землей
[Разработка типовых структурных схем микропроцессорных устройств РЗА на объектах ОАО "ФКС ЕЭС". Пояснительная записка. Новосибирск 2006 г.]EN
shunt fault
short-circuit fault (US)
a fault that is characterized by the flow of current between two or more phases or between phase(s) and earth at the frequency of the associated power system
[IEV ref 448-13-05]FR
défaut shunt
défaut caractérisé par la circulation du courant entre deux ou plusieurs phases ou entre une ou plusieurs phases et la terre, à la fréquence du réseau d'énergie concerné
[IEV ref 448-13-05]Тематики
Синонимы
EN
DE
- Fehler durch Kurzschluss, m
FR
Немецко-русский словарь нормативно-технической терминологии > Fehler durch Kurzschluss, m
-
10 Gas-Durchflusseinstellsystem
система управления расходом газа
Устройство, которое задает расход газа или газовой смеси.
[ ГОСТ Р 52423-2005]Тематики
- ингаляц. анестезия, искусств. вентиляц. легких
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Gas-Durchflusseinstellsystem
См. также в других словарях:
return-flow system — A combustion system in which the entering air and the mixing gases flow in opposite directions. See reverse flow–type turbofan engine … Aviation dictionary
Continuous Flow System — Tintenbehälter eines CIS Die Schläuche am Druckkopf Ein Continuous Ink System (CIS), auch Continuous Ink Supply System (CISS) genannt, ist ein kostengünstiger Ersatz für Patronen von Tintendruckern. Im Gegensatz z … Deutsch Wikipedia
flow, unsteady — A characteristic of a flow system where the magnitude and/or direction of the specific discharge changes with time. Synonymous with nonsteady flow. See also flow, steady … Lexicon of Cave and Karst Terminology
flow, steady — A characteristic of a flow system where the magnitude and direction of specific discharge are constant in time at any point [22]. See also flow, unsteady … Lexicon of Cave and Karst Terminology
flow, uniform — A characteristic of a flow system where specific discharge has the same magnitude and direction at any point [22] … Lexicon of Cave and Karst Terminology
Flow measurement — is the quantification of bulk fluid movement. Flow can be measured in a variety of ways. Positive displacement flow meters acumulate a fixed volume of fluid and then count the number of times the volume is filled to measure flow. Other flow… … Wikipedia
System-on-a-chip — or system on chip (SoC or SOC) refers to integrating all components of a computer or other electronic system into a single integrated circuit (chip). It may contain digital, analog, mixed signal, and often radio frequency functions ndash; all on… … Wikipedia
Flow — may refer to:In science and technology: *Dataflow, computing term related to the flow of messages between software components *Environmental flow, the amount of water necessary in a watercourse to maintain a healthy ecosystem *Flow (computer… … Wikipedia
Flow Snowboarding — Rechtsform Incorporated Gründung 1992 Sitz … Deutsch Wikipedia
flow-chart — (flōʹchärt ) tr.v. flow ·chart·ed, flow ·chart·ing, flow ·charts To design a flow chart for: “Carson put away the papers on which he had been flow charting a system... for a prospering little manufacturer of electric reducing aids” (John Updike) … Universalium
FLOW (Belgium) — FLOW is a Belgian national healthcare network, meant for healthcare providers and patients. It is a acronym which stands for Facilities (services and related infrastructure), Legal implementation (the telex files), Organisations (locoregional… … Wikipedia
