-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
2 классификационный ток ОПН
классификационный ток ОПН
Iкл
Амплитудное значение (более высокое амплитудное значение из двух полярностей, если ток асимметричен) активной составляющей тока промышленной частоты, которое используется для определения классификационного напряжения ОПН и нормируется изготовителем.
[ ГОСТ Р 52725-2007]EN
reference current of an arrester
peak value (the higher peak value of the two polarities if the current is asymmetrical) of the resistive component of a power-frequency current used to determine the reference voltage of the arrester
NOTE 1 The reference current will be high enough to make the effects of stray capacitances at the measured reference voltage of the arrester units (with designed grading system) negligible and is to be specified by the manufacturer.
NOTE 2 Depending on the nominal discharge current and/or line discharge class of the arrester, the reference current will be typically in the range of 0,05 mA to 1,0 mA per square centimetre of disc area for single column arresters.
[IEC 60099-4, ed. 2.0 (2004-05)]FR
courant de référence d'un parafoudre
valeur de crête (la plus grande des deux polarités si le courant est dissymétrique) de la composante résistive du courant à fréquence industrielle utilisée pour déterminer la tension de référence d'un parafoudre.
NOTE 1 Il convient que le courant de référence soit suffisamment élevé pour rendre négligeables les effets des capacités parasites aux tensions de référence mesurées sur les éléments de parafoudre (avec leur système de répartition) et qu’il soit spécifié par le constructeur.
NOTE 2 Fonction du courant de décharge nominal et/ou de la classe de décharge de ligne du parafoudre, il convient que le courant de référence soit typiquement dans la gamme de 0,05 mA à 1,0 mA par centimètre carré de surface de disque pour les parafoudres à colonne unique
[IEC 60099-4, ed. 2.0 (2004-05)]Тематики
- высоковольтный аппарат, оборудование...
EN
FR
Русско-французский словарь нормативно-технической терминологии > классификационный ток ОПН
-
3 переходное восстанавливающееся напряжение
переходное восстанавливающееся напряжение
ПВН
Восстанавливающееся напряжение в течение времени, когда оно имеет заметно выраженный переходный характер. Оно может быть колебательным или апериодическим или их комбинацией, в зависимости от характеристик цепи и выключателя, отражает также смещение напряжения нейтрали многофазной цепи.
ПВН в трехфазных цепях, если не оговорено иное, - это напряжение между выводами первого гасящего полюса, так как это напряжение обычно выше, чем на каждом из двух других полюсов.
[ ГОСТ Р 52565-2006]
переходное восстанавливающееся напряжение
ПВН
Восстанавливающееся напряжение в период времени, когда оно имеет заметно выраженный переходный характер.
Примечания
1 Переходное восстанавливающееся напряжение может быть колебательным или неколебательным или их комбинацией в зависимости от характеристик цепи и коммутационного аппарата. Оно отражает также смещение напряжения нейтрали многофазной цепи.
2 Если не оговорено иначе, переходное восстанавливающееся напряжение в трехфазных цепях представляет собой напряжение между выводами первого отключающего полюса, так как это напряжение обычно более высокое, чем то, которое появляется между выводами каждого из двух других полюсов
[ ГОСТ Р 52726-2007]
восстанавливающееся напряжение 1)
Напряжение в период, когда оно носит в значительной степени переходный характер.
Примечание. Переходное напряжение может быть колебательным или неколебательным, или носить смешанный характер в зависимости от характеристик цепи, коммутационного аппарата или плавкого предохранителя. Сюда относится и сдвиг напряжения нейтрали многофазной цепи.
МЭК 60050(441-17-26)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
1) Должно быть переходное восстанавливающееся напряжение
[Интент]
восстанавливающееся напряжение 1)
Напряжение в период, когда оно носит в значительной степени переходный характер.
Примечания
1 Это переходное напряжение может быть колебательным или неколебательным, или их комбинацией, в зависимости от характеристик цепи и выключателя. При этом учитывают сдвиг напряжения нейтрали многофазной цепи.
2 Восстанавливающееся напряжение в трехфазных цепях в отсутствие других указаний — это напряжение между выводами первого полюса, отключающего ток, поскольку оно, как правило, выше, чем между выводами каждого из двух других полюсов
(МЭС 441-17-26)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
1) Должно быть переходное восстанавливающееся напряжение
[Интент]EN
transient recovery voltage
T.R.V. (abbreviation)
the recovery voltage during the time in which it has a significant transient character
NOTE 1 – The transient recovery voltage may be oscillatory or non-oscillatory or a combination of these depending on the characteristics of the circuit and the switching device. It includes the voltage shift of the neutral of a polyphase circuit.
NOTE 2 – The transient recovery voltages in three-phase circuits is, unless otherwise stated, that across the first pole to clear, because this voltage is generally higher than that which appears across each of the other two poles.
[IEV number 441-17-26 ]FR
tension transitoire de rétablissement
T.T.R. (abréviation)
tension de rétablissement pendant le temps où elle présente un caractère transitoire appréciable
NOTE 1 – La tension transitoire de rétablissement peut être oscillatoire ou non oscillatoire ou être une combinaison de celles-ci selon les caractéristiques du circuit et de l'appareil de connexion. Elle tient compte de la variation du potentiel du point neutre du circuit polyphasé.
NOTE 2 – Sauf spécification contraire, la tension transitoire de rétablissement pour les circuits triphasés est la tension aux bornes du premier pôle qui coupe, car cette tension est généralement plus élevée que celle qui apparaît aux bornes de chacun des deux autres pôles.
[IEV number 441-17-26 ]Тематики
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- T.R.V.
- transient recovery voltage
DE
FR
Русско-французский словарь нормативно-технической терминологии > переходное восстанавливающееся напряжение
-
4 анод
- anode, f
анод (устройства)
электрод, через который электрический ток входит в среду, имеющую удельную проводимость, отличную от удельной проводимости анода
[СТ МЭК50(151)-78]
анод
-
[IEV number 151-13-02]EN
anode
electrode capable of emitting positive charge carriers to and/or receiving negative charge carriers from the medium of lower conductivity
NOTE 1 – The direction of electric current is from the external circuit, through the anode, to the medium of lower conductivity.
NOTE 2 – In some cases (e.g. electrochemical cells), the term "anode" is applied to one or another electrode, depending on the electric operating condition of the device. In other cases (e.g. electronic tubes and semiconductor devices), the term "anode" is assigned to a specific electrode.
[IEV number 151-13-02]FR
anode, f
électrode capable d’émettre des porteurs de charge positifs vers le milieu de plus faible conductivité ou de collecter des porteurs de charge négatifs qui en proviennent
NOTE 1 – Le sens du courant électrique va du circuit extérieur vers le milieu de plus faible conductivité à travers l’anode.
NOTE 2 – Dans certains cas (par exemple pour les éléments électrochimiques), le terme "anode" désigne l’une ou l’autre électrode selon le régime électrique du dispositif. Dans d’autres cas (par exemple pour les tubes électroniques et les dispositifs semiconducteurs), le terme "anode" désigne une électrode particulière.
[IEV number 151-13-02]Тематики
- электротехника, основные понятия
EN
DE
FR
- anode, f
Русско-французский словарь нормативно-технической терминологии > анод
-
5 категория перенапряжения (в цепи или электрической системе)
категория перенапряжения (в цепи или электрической системе)
Условное число, основанное на ограничении (или регулировании) значений ожидаемого переходного перенапряжения, возникающего в цепи (или в электрической системе с различными номинальными напряжениями), зависящее от способов воздействия на перенапряжения.
Примечание. В электрической системе переход от одной категории перенапряжения к другой, более низкой, достигается средствами, совместимыми с требованиями к переходным участкам, например с помощью устройства для защиты от перенапряжений или последовательно-параллельного присоединения импеданса, способного рассеять, поглотить или отклонить энергию соответствующего импульсного тока с целью снижения переходного перенапряжения до желательно меньшей категории перенапряжения.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
категория перенапряжения
Категория электротехнического оборудования по стойкости изоляции к импульсным перенапряжениям (всего четыре категории: I, II, III, IV)
[Интент]EN
overvoltage category (of a circuit or within an electrical system)
conventional number based on limiting (or controlling) the values of prospective transient overvoltages occurring in a circuit (or within an electrical system having different nominal voltages) and depending upon the means employed to influence the overvoltages
NOTE In an electrical system, the transition from one overvoltage category to another of lower category is obtained through appropriate means complying with interface requirements, such as an overvoltage protective device or a series-shunt impedance arrangement capable of dissipating, absorbing, or diverting the energy in the associated surge current, to lower the transient overvoltage value to that of the desired lower overvoltage category
[IEC 60947-1, ed. 5.0 (2007-06)]FR
catégorie de surtension (d'un circuit ou dans un réseau)
nombre conventionnel, basé sur la limitation (ou la commande) des valeurs des surtensions transitoires présumées apparaissant dans un circuit (ou dans un réseau où existent des sections de tensions nominales différentes) et dépendant des moyens employés pour agir sur ces surtensions
NOTE Dans un réseau, le passage d'une catégorie de surtension à une autre de catégorie inférieure est réalisé à l'aide de moyens appropriés répondant aux prescriptions d'interface, tels qu'un dispositif de protection contre les surtensions ou des impédances disposées en séries et/ou en parallèle capables de dissiper, d'absorber ou de détourner l'énergie du courant de surcharge correspondant, afin d'abaisser la valeur des surtensions transitoires à celle qui correspond à la catégorie de surtension inférieure recherchée
[IEC 60947-1, ed. 5.0 (2007-06)]Требуемая стойкость к импульсным напряжениям, кВ:
-
Оборудования на вводе в установку ( IV категория перенапряжения)
-
Оборудования распределительных и конечных цепей ( III категория перенапряжения)
-
Электробытовых приборов и электроприемников ( II категория перенапряжения)
-
Специально защищенного оборудования ( I категория перенапряжения)
[ ГОСТ Р 50571-4-44-2011( МЭК 60364-4-44: 2007) ]
Тематики
- электротехника, основные понятия
EN
- overvoltage categories
- overvoltage category (of a circuit or within an electrical system)
- overvoltage withstand categories
- surge voltage category
FR
Русско-французский словарь нормативно-технической терминологии > категория перенапряжения (в цепи или электрической системе)
-
Оборудования на вводе в установку ( IV категория перенапряжения)
-
6 катод
- cathode, f
катод
-
[IEV number 151-13-03]
катод
Плоская заготовка, получаемая методом электролиза, предназначенная для переплава.
[ ГОСТ 25501-82]
катод
Отрицательный электрод рентгеновской трубки
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]EN
cathode
electrode capable of emitting negative charge carriers to and/or receiving positive charge carriers from the medium of lower conductivity
NOTE 1 – The direction of electric current is from the medium of lower conductivity, through the cathode, to the external circuit.
NOTE 2 – In some cases (e.g. electrochemical cells), the term "cathode" is applied to one or another electrode, depending on the electric operating condition of the device. In other cases (e.g. electronic tubes and semiconductor devices), the term "cathode" is assigned to a specific electrode.
[IEV number 151-13-03]FR
cathode, f
électrode capable d’émettre des porteurs de charge négatifs vers le milieu de plus faible conductivité ou de collecter des porteurs de charge positifs qui en proviennent
NOTE 1 – Le sens du courant électrique va du milieu de plus faible conductivité vers le circuit extérieur à travers la cathode.
NOTE 2 – Dans certains cas (par exemple pour les éléments électrochimiques), le terme "cathode" désigne l’une ou l’autre électrode selon le régime électrique du dispositif. Dans d’autres cas (par exemple pour les tubes électroniques et les dispositifs semiconducteurs), le terme "cathode" désigne une électrode particulière.
[IEV number 151-13-03]Тематики
EN
DE
FR
- cathode, f
Русско-французский словарь нормативно-технической терминологии > катод
-
7 кратность шага скрутки
кратность шага скрутки
отношение шага скрутки к диаметру спирали образуемой одним из компонентов кабеля
Примечание. В зависимости от обстоятельств рассматриваемый диаметр является внутренним средним или наружным диаметром повива, в котором расположен компонент кабеля, образующий спираль
[IEV number 461-04-02]EN
lay ratio
ratio of the length of lay to diameter of the helix formed by one cable component
NOTE – Depending on the circumstances, the diameter to consider is either the internal diameter, or the mean diameter, or the external diameter of the layer in which the component is laid in the helix.
[IEV number 461-04-02]FR
rapport de pas
rapport entre le pas d'assemblage et le diamètre de l'hélice formée par un des constituants du câble
NOTE – Suivant le cas, le diamètre considéré est soit le diamètre intérieur, soit le diamètre moyen, soit le diamètre extérieur de la couche dont fait partie le constituant disposé en hélice.
[IEV number 461-04-02]Тематики
- кабели, провода...
EN
DE
- Verseilfaktor, m
FR
Русско-французский словарь нормативно-технической терминологии > кратность шага скрутки
-
8 максимальный расцепитель тока с независимой выдержкой времени
Максимальное реле или максимальный расцепитель тока с независимой выдержкой времени
Максимальное реле или максимальный расцепитель тока, срабатывающие с определенной выдержкой времени, которая может регулироваться, но не зависит от величины сверхтока.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
definite time-delay over-current release
an over-current release which operates with a definite time-delay, which may be adjustable, but is independent of the value of the over-current
[IEV number 441-16-34]FR
déclencheur à maximum de courant à retard indépendant
déclencheur à maximum de courant qui fonctionne avec un retard défini qui peut être réglable mais est indépendant de la valeur de la surintensité.
[IEV number 441-16-34]Параллельные тексты EN-RU Protection against overload may be provided on both the high-voltage side and the low-voltage side, depending on the transformer power. For low-power transformers the protection should be positioned on the low-voltage side, while for high-power transformers the protection should be provided on the high-voltage side. Protection against overloads on the HV side is provided using HV circuit breakers associated with maximum-current protections in constant time or independent time.
[Legrand]В зависимости от мощности трансформатора, защита от перегрузки выполняется на стороне высшего или низшего напряжения. Мощные трансформаторы защищают со стороны электросети, а маломощные – со стороны нагрузки. Защита от перегрузки на стороне высшего напряжения осуществляется высоковольтным автоматическим выключателем с максимальными расцепителями тока с независимой выдержкой времени.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
- выключатель автоматический
- расцепитель, тепловое реле
- реле электрическое
Классификация
>>>EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > максимальный расцепитель тока с независимой выдержкой времени
-
9 отрицательный электрод
- électrode négative, f
отрицательный электрод
-
[IEV number 151-13-04]EN
negative electrode
for a device having two electrodes, that electrode having the lower electric potential
NOTE – In some cases (e.g. electronic tubes and semiconductor devices), the term "negative electrode" is applied to one or another electrode, depending on the electric operating condition of the device. In other cases (e.g. electrochemical cells), the term "negative electrode" is assigned to a specific electrode.
[IEV number 151-13-04]FR
électrode négative, f
pour un dispositif à deux électrodes, celle des électrodes dont le potentiel électrique est le plus bas
NOTE – Dans certains cas (par exemple pour les tubes électroniques et les dispositifs semiconducteurs), le terme "électrode négative" désigne l’une ou l’autre électrode selon le régime électrique du dispositif. Dans d’autres cas (par exemple pour les éléments électrochimiques), le terme "électrode négative" désigne une électrode particulière.
[IEV number 151-13-04]EN
DE
FR
- électrode négative, f
Русско-французский словарь нормативно-технической терминологии > отрицательный электрод
-
10 положительный электрод
- électrode positive, f
положительный электрод
-
[IEV number 151-13-05]EN
positive electrode
for a device having two electrodes, that electrode having the higher electric potential
NOTE – In some cases (e.g. electronic tubes and semiconductor devices), the term "positive electrode" is applied to one or another electrode, depending on the electric operating condition of the device. In other cases (e.g. electrochemical cells), the term "positive electrode" is assigned to a specific electrode.
[IEV number 151-13-05]FR
électrode positive, f
pour un dispositif à deux électrodes, celle des électrodes dont le potentiel électrique est le plus élevé
NOTE – Dans certains cas (par exemple pour les tubes électroniques et les dispositifs semiconducteurs), le terme "électrode positive" désigne l’une ou l’autre électrode selon le régime électrique du dispositif. Dans d’autres cas (par exemple pour les éléments électrochimiques), le terme "électrode positive" désigne une électrode particulière.
[IEV number 151-13-05]EN
DE
FR
- électrode positive, f
Русско-французский словарь нормативно-технической терминологии > положительный электрод
-
11 пол листовой
пол листовой
Пол с покрытием из листовых материалов
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]SHEET LINOLEUM FLOORING / ROLLED FLOOR (glue down)
Linoleum is very beautiful and durable providing flexible design abilities for bathroom flooring, kitchen flooring, mud room, bedrooms or other areas through use of colors and patterns. This material is natural and since it is made from natural raw materials you may see slight color and structural differences are possible between the production batches and samples. The floor is extremely durable, easy to clean and maintains a warm natural look and feel. Lives of these floors may exceed 40+ years depending on the quality of the installation. I have Marmoleum brand linoleum flooring in my home's recreation room and mud rooms, and could not be happier with its performance.
[http://homerepair.about.com/od/interiorhomerepair/ss/Resilient-Bathroom-And-Kitchen-Flooring-Vinyl-Cork-Linoleum-Flooring_9.htm]
Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > пол листовой
-
12 реле периодической последовательности импульсов
- relais clignotant, m
реле периодической последовательности импульсов
-
[Интент]
EN
flasher relay
repeat cycle relay
time relay in which the output periodically switches on and off as long as the power supply or control signal is applied (see Figure 5)
NOTE 1 – Depending on the relay type, the output starts with "pulse on" or "pulse off".
NOTE 2 – Flasher relay may also be initiated with a control signal.
[IEV ref 445-01-06]FR
relais clignotant, m
relais temporisé dans lequel la sortie passe périodiquement de l'état de travail à l'état de repos tant que l’alimentation ou le signal de commande est appliqué (voir Figure 5)
NOTE 1 – Selon le type de relais, la sortie démarre dans l'état de travail ou dans l'état de repos.
NOTE 2 – Le relais clignotant peut aussi être amorcé par un signal de commande.
[IEV ref 445-01-06]Тематики
EN
DE
- Blinkrelais, n
FR
- relais clignotant, m
Русско-французский словарь нормативно-технической терминологии > реле периодической последовательности импульсов
-
13 химические свойства
химические свойства
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
chemical property
Properties of a substance depending on the arrangement of the atoms in the molecule, e.g. bio-availability, degradability, persistence, etc. (Source: RRDA)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > химические свойства
-
14 восстановление нагрузки
восстановление нагрузки
Процесс увеличения нагрузки потребителя или энергетической системы после восстановления напряжения
[ОАО РАО "ЕЭС России" СТО 17330282.27.010.001-2008]EN
load recovery
after voltage recovery, the increase in load of a consumer or system, at a rate depending on the characteristics of that load
[IEV ref 604-01-35]FR
reprise de la charge
après le retour de la tension, accroissement de la charge d'un usager ou d'un réseau plus ou moins rapide selon les caractéristiques propres à la charge
[IEV ref 604-01-35]Тематики
EN
DE
- Lastwiederkehr, f
FR
Русско-французский словарь нормативно-технической терминологии > восстановление нагрузки
-
15 свойства веществ
свойства веществ
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
behaviour of substances
Reactivity of a compound depending on the structure of the molecules. (Source: RRDA)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > свойства веществ
-
16 программа самопомощи
программа самопомощи
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
self-help programme
A series of steps or a system of services or activities designed to enable an individual to help or improve one's self without depending on the aid of others. (Source: WOR)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > программа самопомощи
-
17 пещера
пещера
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
cave
1) An underground hollow with access from the ground surface or from the sea, often found in limestone areas and on rocky coastlines.
2) A natural cavity, chamber or recess which leads beneath the surface of the earth, generally in a horizontal or obliquely inclined direction. It may be in the form of a passage or a gallery, its shape depending in part on the joint pattern or structure of the rock and partly on the type of process involved in its excavation. Thus, caves worn by subterranean rivers may be different in character from, and of considerably greater extent than, a sea-cave eroded by marine waves.
3) A natural underground open space, generally with a connection to the surface and large enough for a person to enter. The most common type of cave is formed in a limestone by dissolution.
(Source: CED / WHIT / BJGEO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > пещера
-
18 тепловой расцепитель
тепловой расцепитель
Расцепитель, срабатывание которого зависит от теплового действия тока, проходящего через него.
[ ГОСТ 17703-72]EN
thermal release
device which prevents the maintenance of excessively high temperatures in certain parts of the apparatus by disconnecting these parts from their supply
NOTE PTC thermistors (see 2.7.8) are not thermal releases in the sense of this definition
[IEC 60065, ed. 7.0 (2001-12)]
thermal overload release inverse time-delay overload release depending for its operation, including its time delay, on the thermal action of the current flowing in the release
[IEC 60934, ed. 3.0 (2000-10)]FR
limiteur de température
dispositif destiné à empêcher le maintien de températures excessives dans certaines parties de l'appareil, en mettant ces parties hors tension
[IEC 60065, ed. 7.0 (2001-12)]
déclencheur thermique de surcharge déclencheur de surcharge à temps inverse dont le fonctionnement, y compris la temporisation, dépend de l'action thermique du courant qui traverse le déclencheur
[IEC 60934, ed. 3.0 (2000-10)]
В состав теплового расцепителя входит биметаллическая пластина, которая при нагреве выше определенной температуры изгибается, освобождая устройство, удерживающее главные контакты. Быстродействие биметаллической пластины прямо пропорционально значению протекающего через расцепитель тока. Тепловой расцепитель характеризуется тепловой инерцией, и после замыкания сработавшего автоматического выключателя время следующего срабатывания расцепителя уменьшается. В регулируемых расцепителях ток срабатывания можно установить в диапазоне от 0,4 до 1,0 от номинального тока.Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
FR
Русско-французский словарь нормативно-технической терминологии > тепловой расцепитель
-
19 электромагнитный расцепитель
электромагнитный расцепитель
Расцепитель, срабатывание которого зависит от усилия, создаваемого током главной цепи автоматического выключателя в катушке электромагнита.
[ ГОСТ 17703-72]EN
magnetic overload release
overload release depending for its operation on the force exerted by the current in the main circuit exciting the coil of an electromagnet
NOTE Such a release usually has an inverse time-delay/current characteristic.
[IEC 60934, ed. 3.0 (2000-10)]FR
déclencheur magnétique de surcharge
Представляет собой электромагнит, который при возникновении сверхтока воздействует на устройство, удерживающее главные контакты, что приводит к их размыканию. Время реакции очень мало (сотые доли секунды). В регулируемых расцепителях имеется возможность регулировать ток срабатывания в широком (до 10 раз) диапазоне, что позволяет легко настроить автоматический выключатель под конкретные требования защиты. Кроме того, такую регулировку можно использовать для обеспечения селективности срабатывания автоматических выключателей.
déclencheur de surcharge dont le fonctionnement dépend de la force produite par un courant circulant dans le circuit principal et alimentant la bobine d'un électro-aimant
NOTE Un tel relais a généralement des caractéristiques temps inverse/courant
[IEC 60934, ed. 3.0 (2000-10)]Тематики
- выключатель автоматический
- расцепитель, тепловое реле
Классификация
>>>EN
FR
Русско-французский словарь нормативно-технической терминологии > электромагнитный расцепитель
-
20 тепловое реле или расцепитель перегрузки
тепловое реле или расцепитель перегрузки
Реле или расцепитель перегрузки с обратнозависимой выдержкой времени, срабатывание которых (в том числе и выдержка времени) зависит от теплового действия тока, проходящего через это реле или расцепитель.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
thermal overload relay or release
inverse time-delay overload relay or release depending for its operation (including its time-delay) on the thermal action of the current flowing in the relay or release
[IEC 60947-1, ed. 5.0 (2007-06)]FR
relais ou déclencheur thermique de surcharge
relais ou déclencheur de surcharge à temps inverse dont le fonctionnement (y compris la temporisation) dépend de l'action thermique du courant qui traverse le relais ou le déclencheur
[IEC 60947-1, ed. 5.0 (2007-06)]Тематики
- выключатель автоматический
- расцепитель, тепловое реле
- реле электрическое
Классификация
>>>EN
FR
Русско-французский словарь нормативно-технической терминологии > тепловое реле или расцепитель перегрузки
- 1
- 2
См. также в других словарях:
depending on the circumstances — adj. conditional upon circumstances … English contemporary dictionary
The Logic of Violence in Civil War — is a book which challenges the conventional view of violence in civil wars as irrational. The main argument is that violence only emerges in those disputed territories, and it is generally driven not by the conflict itself, but by previous… … Wikipedia
The Hardest Logic Puzzle Ever — is a title coined by George Boolos in La Repubblica 1992 under the title L indovinello più difficile del mondo for the following Raymond Smullyan inspired logic puzzle:Boolos provides the following clarifications:George Boolos, The Hardest Logic… … Wikipedia
The Price Is Right (U.S. game show) — The Price Is Right Format Game show Created by Mark Goodson Bill Todman Directed b … Wikipedia
The House of the Rising Sun — is a folk song from the United States. Also called House of the Rising Sun or occasionally Rising Sun Blues , it tells of a life gone wrong in New Orleans. Depending on the version, the song may be sung from the perspective of a woman or a man.… … Wikipedia
The Chanur novels — The Chanur Saga omnibus The Pride of Chanur Chanur s Venture The Kif Strike Back Chanur s Homecoming Chanur s Legacy Author … Wikipedia
The Amazing Race — sometimes referred to as TAR, is a reality television game show in which teams of two people (with one exception), who have some form of a preexisting personal relationship, race around the world in competition with other teams. Contestants stri … Wikipedia
The Sims 2 — Developer(s) Maxis, Ideaworks Game Studio (Mobile Version) Publisher(s) Electronic Arts (PC) Aspyr (Ma … Wikipedia
The Black Jewels — is a series of fantasy novels by Anne Bishop.The World of the Black JewelsThe Black Jewels Trilogy is set in a unique world consisting of three Realms: Terreille, Kaeleer, and Hell. These three realms, although being situated upon the same land,… … Wikipedia
The Great Brain — is a series of children s books by American author John Dennis Fitzgerald (1907 1988). Set in the fictitious small town of Adenville, Utah, at the turn of the last century, between 1896 and 1898, the stories are loosely based on Fitzgerald s… … Wikipedia
The Law of Ueki — The DVD cover of Volume 1: The Battle Commencement うえきの法則 (Ueki no Hōsoku) … Wikipedia