-
41 continuous current
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
непрерывный ток
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > continuous current
-
42 continuous pusher-type furnace
English-Russian big polytechnic dictionary > continuous pusher-type furnace
-
43 continuous regeneration trap
(CRT) < mvhcl> (type of diesel particulate filter) ■ kontinuierlich arbeitender Partikelfilter mEnglish-german technical dictionary > continuous regeneration trap
-
44 continuous action machine
-
45 continuous film cell
static magnetic cell — магнитная ячейка; магнитный элемент
-
46 continuous charge furnace
English-Russian big polytechnic dictionary > continuous charge furnace
-
47 continuous draw bar
English-Russian big polytechnic dictionary > continuous draw bar
-
48 continuous filter
English-Russian big polytechnic dictionary > continuous filter
-
49 continuous heating furnace
English-Russian big polytechnic dictionary > continuous heating furnace
-
50 continuous kiln
English-Russian big polytechnic dictionary > continuous kiln
-
51 continuous mill
English-Russian big polytechnic dictionary > continuous mill
-
52 continuous pusher furnace
English-Russian big polytechnic dictionary > continuous pusher furnace
-
53 continuous slab heating furnace
English-Russian big polytechnic dictionary > continuous slab heating furnace
-
54 continuous strip-annealing furnace
English-Russian big polytechnic dictionary > continuous strip-annealing furnace
-
55 continuous duty
English-Russian dictionary on nuclear energy > continuous duty
-
56 continuous record
type record — тип "запись"
English-Russian dictionary on nuclear energy > continuous record
-
57 continuous kiln
The English-Russian dictionary general scientific > continuous kiln
-
58 continuous-working kiln
The English-Russian dictionary general scientific > continuous-working kiln
-
59 continuous belt-type hardening furnace
Англо-русский металлургический словарь > continuous belt-type hardening furnace
-
60 continuous conveyor-type furnace
Англо-русский металлургический словарь > continuous conveyor-type furnace
См. также в других словарях:
Continuous-type furnace — Continuous type furnace. См. Печь непрерывного типа. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) … Словарь металлургических терминов
Continuous Miner — Ein Continuous Miner ist eine Gewinnungsmaschine, die im Bergbau Untertage zur Gewinnung von Steinsalz, Gips und Steinkohle eingesetzt wird. Der Continuous Miner gehört aufgrund seiner Bauform zu den Umfangfräsen. Es gibt Continuous Miner in… … Deutsch Wikipedia
Continuous reactor — Continuous reactors (alternatively referred to as flow reactors) carry material as a flowing stream. Reactants are continuously fed into the reactor and emerge as continuous stream of product. Continuous reactors are used for a wide variety of… … Wikipedia
Continuous-wave radar — is a type of radar system where a known stable frequency continuous wave radio energy is transmitted and then received from any reflecting objects.[1]Continuous wave (CW) radar uses Doppler, which renders the radar immune to interference from… … Wikipedia
Continuous training — is a type of physical training that involves activity without rest. This type of training may be of high intensity, of moderate intensity with an extended duration, or fartlek training.[1] Continuous training means the pe Continuous training can… … Wikipedia
Continuous Computing — Type Private Industry Technology Founded 1998 … Wikipedia
Continuous-flow intersection — in West Valley City, Utah showing the layout and normal traffic flow in the southwest portion of the intersection. Continuous flow intersection (CFI), also called a crossover displaced left turn (XDL), is an at grade intersection that moves the… … Wikipedia
Continuous cruiser — (CCer) is a class of licence fees on the inland waterways of the United Kingdom. It also refers to the boats and owners who have such a licence, but some people restrict this usage to boaters who genuinely cruise continuously (see below).… … Wikipedia
Continuous motion pot washing — systems are (in the most basic form) three compartment sinks with an agitating wash compartment. Most commonly used in the food service industry, the term continuous motion pot washing describes washing systems that do not have a set wash cycle… … Wikipedia
Continuous obsolescence — or perpetual revolution is a phenomenon where industry trends, or other items that do not immediately correspond to technical needs, mandate a continual readaptation of a system; such work does not increase the usefulness of the system, but is… … Wikipedia
Continuous predicate — is a term coined by Charles Sanders Peirce (1839–1914) to describe a special type of relational predicate that results as the limit of a recursive process of hypostatic abstraction. Here is one of Peirce s definitive discussions of the concept:… … Wikipedia