-
121 EXW (insert named place of delivery)
франко завод (с указанием поименованного места поставки)
EXW (с указанием поименованного места поставки)
Данный термин означает, что продавец осуществляет поставку, когда он предоставляет товар в распоряжение покупателя в своих помещениях или в ином согласованном месте (т.е. на предприятии, складе и т.д.). Продавцу необязательно осуществлять погрузку товара на любое транспортное средство, он также не обязан выполнять формальности, необходимые для вывоза, если таковые применяются. Покупатель несет все расходы и риски, связанные с принятием товара в согласованном пункте (если таковой указан) в поименованном месте поставки. EXW возлагает на продавца минимальные обязанности. Данный термин может быть использован независимо от избранного вида транспорта, а также при использовании более чем одного вида транспорта. Он является подходящим для внутренней торговли, тогда как FCA (Франко перевозчик) обычно используется в международной торговле (ИНКОТЕРМС 2010)
[Упрощение процедур торговли: англо-русский глоссарий терминов (пересмотренное второе издание) НЬЮ-ЙОРК, ЖЕНЕВА, МОСКВА 2011 год]EN
EXW (insert named place of delivery)
ex works (insert named place of delivery)
Incoterm under which the seller delivers when it places the goods at the disposal of the buyer at the seller’s premises or at another named place (i.e., works, factory, warehouse, etc.). The seller does not need to load the goods on any collecting vehicle, nor does it need to clear the goods for export, where such clearance is applicable. The buyer bears all costs and risks involved in taking the goods from the agreed point, if any, at the named place of delivery. EXW represents the minimum obligation for the seller. This rule may be used irrespective of the mode of transport selected and may also be used where more than one mode of transport is employed. It is suitable for domestic trade, while FCA is usually more appropriate for international trade (INCOTERMS 2010)
[Trade Facilitation Terms: An English - Russian Glossary (revised second edition) NEW YORK, GENEVA, MOSCOW 2379]Тематики
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > EXW (insert named place of delivery)
-
122 reduce
1. v снижать; сбавлять, уменьшать; сокращать2. v ослаблять, уменьшать3. v худеть; соблюдать диету для похуденияto reduce by 10 pounds — похудеть на 10 фунтов, сбросить 10 фунтов
4. v вызывать похудение, истощать5. v превращать, обращатьwater can be reduced to oxygen and hydrogen by electrolysis — электролизом можно разложить воду на кислород и водород
6. v переводить, превращать7. v мат. сокращать, преобразовывать; приводить8. v доводитьto be reduced to penury — дойти до нищеты, впасть в нужду
9. v сводитьthe whole question reduces itself to the question whether … — весь вопрос сводится к тому, было ли …
10. v заставлять, вынуждать11. v покорять, подчинять себе, побеждать12. v воен. подавлять13. v упрощать14. v мат. приводить к более простому виду15. v укорачивать16. v мед. вправлять; исправлять положение отломков кости17. v уст. поэт. вернуть; восстановить18. v фон. редуцировать, ослаблять19. v тех. измельчать; размалывать20. v разбавить; развести21. v фото уменьшать плотность22. v метал. раскислять23. v хим. восстанавливать24. v спец. пересчитывать показатели на нормальную температуру и давлениеСинонимический ряд:1. cut (verb) chop; clip; crop; cut; cut back; lop; lower; mark down; pare; shave; shear; slash; trim2. cut down (verb) cut down; exercise; slenderize; slim down3. decrease (verb) bate; close; decrease; drain away; dwindle; peak out; peter out; rebate; recede; taper; taper off4. defeat (verb) bear down; beat down; conquer; crush; defeat; depose; overcome; overpower; overthrow; subdue; subjugate; suppress; vanquish5. degrade (verb) abase; break; bump; bust; debase; declass; degrade; demerit; demote; depress; disgrade; disrate; downgrade; humiliate; put down6. diet (verb) diet; slim; trim down7. drain (verb) abate; diminish; drain; ebb; let up; shrink; tail off8. lessen (verb) abridge; attenuate; contract; curtail; deduct; discount; lessen; retrench9. lower (verb) cheapen; depreciate; devaluate; devalue; lower; mark downАнтонимический ряд:aggrandise; amplify; augment; broaden; defend; develop; dissociate; distend; elevate; enhance; enlarge; enrich; exalt; except; gain; increase -
123 gorge réelle (soudures d'angle)
теоретическая толщина углового шва
Высота наибольшего равнобедренного треугольника, который можно вписать в сечение выполненного шва; теоретическая толщина стыкового шва: Минимальное расстояние от поверхности детали до корня шва [ИСО 2553]
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]EN
actual throat thickness
(fillet welds), the value of the height of the largest isosceles triangle that can be inscribed in the section of the finalized weld (butt welds), the minimum distance from the surface of the part to the bottom of the penetration [ISO 2553]
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]FR
gorge réelle (soudures d'angle)
épaisseur réelle (soudures bout а bout)
(soudures d'angle) hauteur duplus grand triangle isocèle pouvant кtre inscrit dans la soudure terminée (soudures bout а bout) distance minimale de la surface de la pièce а la partie inférieure de la penetration envers [ISO 2553]
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]Тематики
- сварка, резка, пайка
EN
FR
Франко-русский словарь нормативно-технической терминологии > gorge réelle (soudures d'angle)
-
124 épaisseur réelle (soudures bout а bout)
теоретическая толщина углового шва
Высота наибольшего равнобедренного треугольника, который можно вписать в сечение выполненного шва; теоретическая толщина стыкового шва: Минимальное расстояние от поверхности детали до корня шва [ИСО 2553]
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]EN
actual throat thickness
(fillet welds), the value of the height of the largest isosceles triangle that can be inscribed in the section of the finalized weld (butt welds), the minimum distance from the surface of the part to the bottom of the penetration [ISO 2553]
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]FR
gorge réelle (soudures d'angle)
épaisseur réelle (soudures bout а bout)
(soudures d'angle) hauteur duplus grand triangle isocèle pouvant кtre inscrit dans la soudure terminée (soudures bout а bout) distance minimale de la surface de la pièce а la partie inférieure de la penetration envers [ISO 2553]
[ ГОСТ Р ИСО 17659-2009] [ISO 17659:2002]Тематики
- сварка, резка, пайка
EN
FR
Франко-русский словарь нормативно-технической терминологии > épaisseur réelle (soudures bout а bout)
-
125 motor trip class
класс расцепления
-
[Интент]Параллельные тексты EN-RU
The trip classes usually considered and most commonly used are 10A –10 – 20 – 30 referred to the time “Ti”. It is quite common speaking of normal starting and associate to it the trip classes 10A and 10, or of heavy starting making reference to the trip classes 20 and 30.
The limits fixed for “Ti”, which is the generic tripping time of the thermal protection, have the following meaning:
- the lower limit represents the minimum time under which the relay mustn’t trip in order not to interfere during starting;
- the upper limit is the time within which the relay shall surely trip.
[ABB]Наиболее часто применяют тепловые реле с классом расцепления: 10A, 10, 20 и 30, определяемым временем расцепления Ti. Для электродвигателя, выполняющего пуск в нормальных условиях, применяют тепловые реле с классом расцепления 10А или 10, а в тяжелых условиях – с классом 20 или 30.
Пределы, установленные для параметра Ti (типичное время расцепления устройства тепловой защиты), означают следующее:
– нижний предел представляет собой минимальное время, в течение которого реле не должно сработать и дать возможность выполнить пуск двигателя;
– верхний предел представляет собой время, в течение которого реле должно обязательно сработать.
[Перевод Интент]Тематики
- расцепитель, тепловое реле
EN
Англо-русский словарь нормативно-технической терминологии > motor trip class
-
126 starting class
класс расцепления
-
[Интент]Параллельные тексты EN-RU
The trip classes usually considered and most commonly used are 10A –10 – 20 – 30 referred to the time “Ti”. It is quite common speaking of normal starting and associate to it the trip classes 10A and 10, or of heavy starting making reference to the trip classes 20 and 30.
The limits fixed for “Ti”, which is the generic tripping time of the thermal protection, have the following meaning:
- the lower limit represents the minimum time under which the relay mustn’t trip in order not to interfere during starting;
- the upper limit is the time within which the relay shall surely trip.
[ABB]Наиболее часто применяют тепловые реле с классом расцепления: 10A, 10, 20 и 30, определяемым временем расцепления Ti. Для электродвигателя, выполняющего пуск в нормальных условиях, применяют тепловые реле с классом расцепления 10А или 10, а в тяжелых условиях – с классом 20 или 30.
Пределы, установленные для параметра Ti (типичное время расцепления устройства тепловой защиты), означают следующее:
– нижний предел представляет собой минимальное время, в течение которого реле не должно сработать и дать возможность выполнить пуск двигателя;
– верхний предел представляет собой время, в течение которого реле должно обязательно сработать.
[Перевод Интент]Тематики
- расцепитель, тепловое реле
EN
Англо-русский словарь нормативно-технической терминологии > starting class
-
127 trip class
класс расцепления
-
[Интент]Параллельные тексты EN-RU
The trip classes usually considered and most commonly used are 10A –10 – 20 – 30 referred to the time “Ti”. It is quite common speaking of normal starting and associate to it the trip classes 10A and 10, or of heavy starting making reference to the trip classes 20 and 30.
The limits fixed for “Ti”, which is the generic tripping time of the thermal protection, have the following meaning:
- the lower limit represents the minimum time under which the relay mustn’t trip in order not to interfere during starting;
- the upper limit is the time within which the relay shall surely trip.
[ABB]Наиболее часто применяют тепловые реле с классом расцепления: 10A, 10, 20 и 30, определяемым временем расцепления Ti. Для электродвигателя, выполняющего пуск в нормальных условиях, применяют тепловые реле с классом расцепления 10А или 10, а в тяжелых условиях – с классом 20 или 30.
Пределы, установленные для параметра Ti (типичное время расцепления устройства тепловой защиты), означают следующее:
– нижний предел представляет собой минимальное время, в течение которого реле не должно сработать и дать возможность выполнить пуск двигателя;
– верхний предел представляет собой время, в течение которого реле должно обязательно сработать.
[Перевод Интент]Тематики
- расцепитель, тепловое реле
EN
Англо-русский словарь нормативно-технической терминологии > trip class
-
128 tripping class
класс расцепления
-
[Интент]Параллельные тексты EN-RU
The trip classes usually considered and most commonly used are 10A –10 – 20 – 30 referred to the time “Ti”. It is quite common speaking of normal starting and associate to it the trip classes 10A and 10, or of heavy starting making reference to the trip classes 20 and 30.
The limits fixed for “Ti”, which is the generic tripping time of the thermal protection, have the following meaning:
- the lower limit represents the minimum time under which the relay mustn’t trip in order not to interfere during starting;
- the upper limit is the time within which the relay shall surely trip.
[ABB]Наиболее часто применяют тепловые реле с классом расцепления: 10A, 10, 20 и 30, определяемым временем расцепления Ti. Для электродвигателя, выполняющего пуск в нормальных условиях, применяют тепловые реле с классом расцепления 10А или 10, а в тяжелых условиях – с классом 20 или 30.
Пределы, установленные для параметра Ti (типичное время расцепления устройства тепловой защиты), означают следующее:
– нижний предел представляет собой минимальное время, в течение которого реле не должно сработать и дать возможность выполнить пуск двигателя;
– верхний предел представляет собой время, в течение которого реле должно обязательно сработать.
[Перевод Интент]Тематики
- расцепитель, тепловое реле
EN
Англо-русский словарь нормативно-технической терминологии > tripping class
См. также в других словарях:
History of the minimum wage — The history of minimum wage is about the attempts and measures governments have made to introduce a standard amount of periodic pay below which employers could not let their workers fall. Contents 1 Nineteenth century 2 Twentieth century 3 See… … Wikipedia
Liebig's law of the minimum — Liebig s Law of the Minimum, often simply called Liebig s Law or the Law of the Minimum, is a principle developed in agricultural science by Carl Sprengel (1828) and later popularized by Justus von Liebig. It states that growth is controlled not… … Wikipedia
law of the minimum — n a law in physiology: when a process is conditioned by several factors its rate is limited by the factor present in the minimum … Medical dictionary
value of the minimum share contribution — mažiausiasis pajinio įnašo dydis statusas Aprobuotas sritis žemės ūkio politika apibrėžtis Žemės ūkio bendrovės narių susirinkimo nustatytas tam tikras įnašo dydis, išreikštas pinigine verte. atitikmenys: angl. amount of the minimal member share… … Lithuanian dictionary (lietuvių žodynas)
law of the minimum — a law in physiology: when a process is conditioned by several factors its rate is limited by the factor present in the minimum … Useful english dictionary
Law of the Minimum — the growth of a population is limited by the resource in shortest supply. Also known as Liebig s Law … Dictionary of ichthyology
Minimum wage law — is the body of law which prohibits employers from hiring employees or workers for less than a given hourly, daily or monthly minimum wage. More than 90% of all countries have some kind of minimum wage legislation.[1] Until recently, minimum wage… … Wikipedia
Minimum spanning tree — The minimum spanning tree of a planar graph. Each edge is labeled with its weight, which here is roughly proportional to its length. Given a connected, undirected graph, a spanning tree of that graph is a subgraph that is a tree and connects all… … Wikipedia
Minimum wage in Hong Kong — The Legislative Council voted to introduce a minimum wage in Hong Kong in July 2010.[1] The executive branch proposed a minimum wage of HK$28 ( US$3.60) per hour in November 2010, which the Legislative Council voted to accept after much debate in … Wikipedia
Minimum Information Standards — Minimum Information (MI) standards or reporting guidelines specify the minimum amount of meta data (information) and data required to meet a specific aim or aims. Usually the aim is to provide enough meta data and data to enable the unambiguous… … Wikipedia
Minimum wage history — The history of minimum wage is about the attempts and measures governments have made to introduce a standard amount of periodic pay below which employers could not let their workers fall.In 1824 in Victoria, Australia, an amendment to the… … Wikipedia