-
121 disc type winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disc type winding
-
122 disc winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disc winding
-
123 disk type winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disk type winding
-
124 disk winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
дисковая обмотка
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > disk winding
-
125 prism clamp
Зажим призматический для присоединения кабелей сечением до 70 мм2
Рис. ABB
Зажим призматический для присоединения кабелей сечением до 150 мм2
Рис. ABBТематики
- вывод, зажим электрический
EN
Англо-русский словарь нормативно-технической терминологии > prism clamp
-
126 cable shroud
1 - защитная кабельная крышка
Рис. ABBПараллельные тексты EN-RU
The cable shroud can be mounted after the cable installation.
[ABB]Защитную кабельную крышку можно установить на устройстве после присоединения кабелей.
[Перевод Интент]Тематики
- аппарат, изделие, устройство...
EN
Англо-русский словарь нормативно-технической терминологии > cable shroud
-
127 variation of the magnetic tripping
изменение характеристики срабатывания электромагнитного расцепителя
-Рис. ABB
Параллельные тексты EN-RU
1 - No variation in the tripping due to overload
2 - Variation in the instantaneous tripping due to short-circuit
[ABB]1 - Характеристика срабатывания не изменяется в зоне токов перегрузки
2 - Изменение характеристики мгновенного срабатывания в зоне токов короткого замыкания
[Перевод Интент]Примечание. Речь идет об изменении характеристики срабатывания расцепителя переменного тока в зоне токов короткого замыкания при работе в цепи постоянного тока.
[Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > variation of the magnetic tripping
-
128 ISC
- ток короткого замыкания
- межсистемная связь
- международный центр коммутации
- международный коммутационный центр
- информация о пошагово управляемом положении
информация о пошагово управляемом положении
—
[ ГОСТ Р 54325-2011 (IEC/TS 61850-2:2003)]]Тематики
EN
международный коммутационный центр
—
[Л.Г.Суменко. Англо-русский словарь по информационным технологиям. М.: ГП ЦНИИС, 2003.]Тематики
EN
международный центр коммутации
(МСЭ-T M.2100, МСЭ-Т I.358).
[ http://www.iks-media.ru/glossary/index.html?glossid=2400324]Тематики
- электросвязь, основные понятия
EN
межсистемная связь
—
[Е.С.Алексеев, А.А.Мячев. Англо-русский толковый словарь по системотехнике ЭВМ. Москва 1993]Тематики
EN
ток короткого замыкания
Сверхток, появляющийся в результате короткого замыкания, вызываемого повреждением или неправильным соединением в электрической цепи.
МЭК 60050(441-11-07)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
ток короткого замыкания
Сверхток, обусловленный замыканием с ничтожно малым полным сопротивлением между точками, которые в нормальных условиях эксплуатации должны иметь различный потенциал.
Примечание — Ток короткого замыкания может явиться результатом повреждения или неправильного соединения
(МЭС 441—11—07)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
ток короткого замыкания
Электрический ток в данной короткозамкнутой цепи.
[ ГОСТ Р МЭК 60050-195-2005]
ток короткого замыкания (Ic)
Сверхток, появляющийся в результате короткого замыкания, вследствие повреждения или неправильного соединения в электрической цепи
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
ток короткого замыкания
Электрический ток при данном коротком замыкании.
[ ГОСТ Р МЭК 60050-826-2009]
ток короткого замыкания
Сверхток, возникающий в результате короткого замыкания из-за дефекта или неправильного подключения в электрической цепи.
[ ГОСТ Р МЭК 60204-1-2007]EN
short-circuit current
an over-current resulting from a short circuit due to a fault or an incorrect connection in an electric circuit
[IEV number 441-11-07]
short-circuit current
electric current in a given short-circuit
Source: 603-02-28 MOD
[IEV number 195-05-18]
[IEV number 826-11-16]FR
courant de court-circuit
surintensité résultant d'un court-circuit dû un défaut ou à un branchement incorrect dans un circuit électrique
[IEV number 441-11-07
courant de court-circuit
courant électrique dans un court-circuit déterminé
Source: 603-02-28 MOD
[IEV number 195-05-18]
[IEV number 826-11-16]
Рис. 7 (Рис. ABB)
Контур тока короткого замыкания при замыкании на землю в системе ТТ
1 - Вторичная обмотка трансформатора;
2 - Линейный проводник;
3 - Сопротивление в месте замыкания;
4 - Проводник защитного заземления;
5 - Зазеамляющий электрод электроустановки;
6 - Заземляющий электрод нейтрали вторичной обмотки тарнсформатораПараллельные тексты EN-RU
An earth fault in a TT system originates the circuit represented in Figure 7.
The fault current flows through the secondary winding of the transformer, the line conductor, the fault resistance, the protective conductor, and the earth electrode resistances (RA, of the user’s plant, and RB, of the neutral).
[ABB]Замыкание на землю в системе TT образует цепь, представленную на рисунке 7.
Ток короткого замыкания протекает через вторичную обмотку трансформатора, линейный проводник, сопротивление в месте замыкания, проводник защитного заземления, заземляющие электроды (RA электроустановки и RB нейтрали вторичной обмотки трансформатора).
[Перевод Интент]Тематики
- электробезопасность
- электротехника, основные понятия
- электроустановки
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > ISC
См. также в других словарях:
ABB — steht für: Asea Brown Boveri (ABB Ltd), einen Elektrotechnikkonzern, sowie ABB Stotz Kontakt, einen Automatisierungstechnikhersteller Allman Brothers Band Ape, Beck Brinkmann, eine Do Rock Band ABB Records, ein Hip Hop Label Adam Bernhard… … Deutsch Wikipedia
Abb — Cette page d’homonymie répertorie les différents sujets et articles partageant un même nom. {{{image}}} Sigles d une seule lettre Sigles de deux lettres > Sigles de trois lettres … Wikipédia en Français
Abb — ([a^]b), n. [AS. [=a]web, [=a]b; pref. a + web. See {Web}.] Among weavers, yarn for the warp. Hence, {abb wool} is wool for the abb. [1913 Webster] … The Collaborative International Dictionary of English
Abb. — Abb. 〈Abk. für〉 Abbildung * * * Abb. = ↑ Abbildung. * * * Abb., Abkürzung für Abbildung. * * * Abb. = ↑Abbildung (3) … Universal-Lexikon
ABB — is a three letter abbreviation that may refer to: *American Body Building (with products often labeled as ABB), a supplement brand centered around sports supplements. www.americanbodybuilding.com *ABB Group, formerly Asea Brown Boveri, a… … Wikipedia
Abb'e — Ab b[ e] ([.a]b b[asl] ), n. [F. abb[ e]. See {Abbot}.] The French word answering to the English abbot, the head of an abbey; but commonly a title of respect given in France to every one vested with the ecclesiastical habit or dress. [1913… … The Collaborative International Dictionary of English
Abb. — Abb., Abkürzung für abbassamento (ital.), Tieferstellung, beim Klavierspiel Vorschrift, daß die eine Hand unter der andern spielen soll … Kleines Konversations-Lexikon
Abb. — Abb. abbr. 1. abbess. 2. abbot. * * * … Universalium
Abb. — Abb. = Abbildung … Die deutsche Rechtschreibung
abb- — is often found in older spelling where ab is now used. Thus abbase, abbatis, abbet, abbettor, abbay, abbortive, abbredge, abbut, abbuttal, which see under their ordinary spelling with one b … Useful english dictionary
ABB — Este artículo trata sobre el grupo empresarial multinacional. Para otros usos de este término, véase ABB (desambiguación). Asea Brown Boveri … Wikipedia Español