-
1 бестоковая пауза коммутационного аппарата
бестоковая пауза коммутационного аппарата
Интервал времени с момента погасания дуги во всех полюсах контактного аппарата до момента возникновения тока в одном из его полюсов при автоматическом повторном включении.
[ ГОСТ 17703-72]
бестоковая пауза при АПВ
Интервал времени между окончательным погасанием дуги во всех полюсах при операции отключения и первого появления тока в любом из полюсов при последующей операции включения
[ ГОСТ Р 52565-2006]
бестоковая пауза
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]EN
dead time (during auto-reclosing)
the interval of time between final arc extinction in all poles on the opening operation and the first reestablishment of current in any pole on the subsequent closing operation
[IEV number 441-17-44 ]FR
durée de coupure-établissement (d'une refermeture automatique)
intervalle de temps entre l'extinction finale des arcs sur tous les pôles à l'ouverture et le premier rétablissement du courant sur n'importe quel pôle lors de la fermeture qui lui fait suite
[IEV number 441-17-44 ]Согласно стандартам МЭК и ANSI/IEEE нормируемая бестоковая пауза равна 300 мс.
[http://forca.ru/info/spravka/bestokovaya-pauza-vyklyuchatelya-pri-avtomaticheskom-povtornom-vklyuchenii.html]Тематики
- высоковольтный аппарат, оборудование...
- релейная защита
- электроснабжение в целом
Синонимы
- бестоковая пауза
- бестоковая пауза выключателя при автоматическом повторном включении
- бестоковая пауза при АПВ
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > бестоковая пауза коммутационного аппарата
-
2 воздействующая величина электрического реле
воздействующая величина электрического реле
Электрическая величина, которая одна или в сочетании с другими электрическими величинами должна быть приложена к электрическому реле в заданных условиях для достижения ожидаемого функционирования
[ ГОСТ 16022-83]EN
energizing quantity
an electrical quantity (either current or voltage) which alone, or in combination with other such quantities, applied to a relay under specified conditions enables it to fulfil its purpose
[IEV number 446-12-01]
energizing quantity (for elementary relays)electrical quantity which, when applied to the input circuit of an elementary relay under specified conditions, enables it to fulfill its purpose
NOTE – For elementary relays the energizing quantity is usually a voltage. Therefore, the input voltage as energizing quantity is used in the definitions given below. Where a relay is energized by a given current instead, the respective terms and definitions apply with "current" used instead of "voltage".
[IEV number 444-03-01]FR
grandeur d'alimentation
grandeur électrique, courant ou tension, qui, seule ou en combinaison avec d'autres grandeurs électriques, courant ou tension, doit être appliquée dans des conditions spécifiées à un relais pour en obtenir le comportement attendu
[IEV number 446-12-01]
grandeur d'alimentation (pour les relais élémentaires), f
grandeur électrique qui, appliquée au circuit d'entrée d'un relais élémentaire dans des conditions spécifiées, lui permet d'accomplir sa fonction
NOTE – Pour les relais élémentaires, la grandeur d'alimentation est en général une tension. En conséquence, on utilise la tension d'entrée comme grandeur d'alimentation dans les définitions données ci-dessous. Lorsqu'un relais est alimenté par un courant, les termes et définitions respectifs sont à utiliser avec le terme "courant" au lieu du terme "tension".
[IEV number 444-03-01]Тематики
Классификация
>>>EN
DE
FR
49. Воздействующая величина электрического реле
D. Eingangsgrösse
Е. Energizing quantity
F. Grandeur d’alimentation
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-немецкий словарь нормативно-технической терминологии > воздействующая величина электрического реле
-
3 инструктированный персонал
инструктированный персонал
Лица, соответственно проинструктированные квалифицированным персоналом или выполняющие работы под наблюдением квалифицированного персонала, что позволяет им оценивать риски и избегать опасностей, которые может создавать электричество.
[ ГОСТ Р МЭК 60050-195-2005]
(электротехнически) инструктированный персонал
Лица, соответственно проинструктированные электротехнически квалифицированным персоналом или выполняющие работы под наблюдением квалифицированного персонала, что позволяет им оценивать риски и избегать опасности, которые может создавать электричество.
[ ГОСТ Р МЭК 60050-826-2009]EN
(electrically) instructed person
person adequately advised or supervised by electrically skilled persons to enable him or her to perceive risks and to avoid hazards which electricity can create
[IEV number 195-04-02]FR
personne avertie (en électricité)
personne suffisamment informée ou surveillée par des personnes qualifiées en électricité pour lui permettre de percevoir les risques et d’éviter les dangers que peut présenter l’électricité
[IEV number 195-04-02]Тематики
Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > инструктированный персонал
-
4 квалифицированный персонал
квалифицированный персонал
Лица, имеющие соответствующее образование и опыт, позволяющие им оценивать риски и избегать опасностей, которые может создавать электричество.
[ ГОСТ Р МЭК 60050-195-2005]
(электротехнически) квалифицированный персонал
Лица, имеющие соответствующее образование и опыт, позволяющие им оценивать риски и избегать опасности, которые может создавать электричество
[ ГОСТ Р МЭК 60050-826-2009]EN
(electrically) skilled person
person with relevant education and experience to enable him or her to perceive risks and to avoid hazards which electricity can create
[IEV number 195-04-01]FR
personne qualifiée (en électricité)
personne ayant la formation et l’expérience appropriées pour lui permettre de percevoir les risques et d’éviter les dangers que peut présenter l’électricité
[IEV number 195-04-01]Тематики
Синонимы
EN
- (electrically) skilled person
- professional person
- qualified personnel
- qualified technician
- specially trained personnel
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > квалифицированный персонал
-
5 линия
линия
-
[IEV number 151-12-27]EN
line
device connecting two points for the purpose of conveying electromagnetic energy between them
NOTE 1 – Electromagnetic energy may be extracted from or supplied to a line at an intermediate point.
NOTE 2 – Examples of lines are two-wire line, polyphase line, coaxial line, waveguide.
Source: 466-01-01 MOD, 601-03-03 MOD
[IEV number 151-12-27]FR
ligne, f
dispositif reliant deux points et destiné à transmettre de l'énergie électromagnétique entre eux
NOTE 1 – De l'énergie électromagnétique peut être extraite d'une ligne ou lui être fournie en un point intermédiaire.
NOTE 2 – Des exemples de lignes sont une ligne bifilaire, une ligne polyphasée, une ligne coaxiale, un guide d'ondes.
Source: 466-01-01 MOD, 601-03-03 MOD
[IEV number 151-12-27]EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > линия
-
6 максимальная допустимая температура
максимальная допустимая температура
-
[IEV number 442-06-41]EN
maximum permissible temperature
maximum service temperature
Denotes the highest temperature which the connecting device is allowed to attain in normal use as a result of ambient temperature, induced heat, and heat caused by the device itself
[IEV number 442-06-41]FR
température maximale permise
température maximale de service
Température la plus élevée que le dispositif de connexion peut atteindre en usage normal et résultant de la température ambiante, de la chaleur induite et de la chaleur dégagée par le dispositif lui-même
[IEV number 442-06-41]EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > максимальная допустимая температура
-
7 номинальное напряжение изоляции (соединительного устройства)
напряжение по изоляции
Напряжение, определяемое изготовителем для данного соединителя и его составных частей, с которыми соотносятся испытания на электрическую прочность изоляции, воздушные зазоры и расстояния утечки.
[ ГОСТ Р 51323.1-99]
номинальное напряжение изоляции (соединительного устройства)
-
[IEV number 442-06-39]EN
rated insulation voltage, (of a connecting device)
phase/neutral or phase/phase voltage value assigned to the connecting device by the manufacturer, this device being intended to be used in installations, the voltage supply of which does not exceed the rated insulation voltage of the connecting device itself
NOTE – Rated insulation voltage is always understood to be between live parts and not between live parts and earth (ground).
[IEV number 442-06-39]FR
tension d'isolement assignée (d'un dispositif de connexion)
valeur de la tension phase/neutre ou phase/phase assignée par le constructeur du dispositif de connexion, celui-ci étant prévu pour être utilisé dans des installations dont la tension d'alimentation ne dépasse pas la tension d'isolement assignée du dispositif de connexion lui-même
NOTE – La tension d'isolement assignée est toujours comprise comme la tension entre parties sous tension et non entre parties sous tension et terre.
[IEV number 442-06-39]Тематики
EN
- rated insulation voltage, (of a connecting device)
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > номинальное напряжение изоляции (соединительного устройства)
-
8 оперирование контактного коммутационного аппарата за счет запасенной энергии
оперирование контактного коммутационного аппарата за счет запасенной энергии
Управление путем приложения энергии, накопленной в самом механизме до завершения оперирования и достаточной для доведения его до конца в заданных условиях.
МЭК 60050(441-16-15).
Примечание. Такое управление можно характеризовать:
1) способом накопления энергии (применению пружины, груза и т. п.);
2) происхождением энергии (ручной, электрической и т. п.);
3) способом высвобождения этой энергии (ручному, электрическому и т. п.).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
stored energy operation (of a mechanical switching device)
an operation by means of energy stored in the mechanism itself prior to the completion of the operation and sufficient to complete it under predetermined conditions
NOTE – This kind of operation may be subdivided according to:
1. The manner of storing the energy (spring, weight, etc.);
2. The origin of the energy (manual, electric, etc.);
3. The manner of releasing the energy (manual, electric, etc.).
[IEV number 441-16-15 ]FR
manoeuvre à accumulation d'énergie (d'un appareil mécanique de connexion)
manoeuvre effectuée au moyen d'énergie emmagasinée dans le mécanisme lui-même avant l'achèvement de la manoeuvre et suffisante pour achever la manoeuvre dans des conditions prédéterminées
NOTE – Ce type de manoeuvre peut être subdivisé suivant:
1. le mode d'accumulation de l'énergie (ressort, poids, etc.);
2. la provenance de l'énergie (manuelle, électrique, etc.);
3. le mode de libération de l'énergie (manuel, électrique, etc.).
[IEV number 441-16-15 ]Тематики
- аппарат, изделие, устройство...
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > оперирование контактного коммутационного аппарата за счет запасенной энергии
-
9 падение или повышение напряжения при заданном режиме нагрузки
падение или повышение напряжения при заданном режиме нагрузки
Разность между напряжением холостого хода обмотки и напряжением на ее выводах при заданных нагрузке и коэффициенте мощности при условии, что к другой (или к одной из других) обмотке(ок) подведено напряжение, равное:
- номинальному, если трансформатор включен на основное ответвление (в этом случае напряжение холостого хода рассматриваемой обмотки равно номинальному);
- напряжению другого ответвления, на которое включен трансформатор. Падение или повышение напряжения обычно выражают в процентах напряжения холостого хода рассматриваемой обмотки.
Примечание — В многообмоточном трансформаторе падение или повышение напряжения зависит от нагрузки и коэффициента мощности не только данной обмотки, но и других обмоток
(МЭС 421-07-03).
[ ГОСТ 30830-2002]EN
voltage drop or rise for a specified load condition
voltage regulation for a specified load condition
the arithmetic difference between the no-load voltage of a winding and the voltage developed at the terminals of the same winding at a specified load and power factor, the voltage supplied to (one of) the other winding(s) being equal to:
- its rated value if the transformer is connected on the principal tapping (the no-load voltage of the former winding is then equal to its rated value);
- the tapping voltage if the transformer is connected on another tapping.
This difference is generally expressed as a percentage of the no-load voltage of the former winding
NOTE – For multi-winding transformers, the voltage drop or rise depends not only on the load and power factor of the winding itself, but also on the load and power factor of the other windings
[IEV number 421-07-03]FR
hute ou augmentation de tension pour une condition de charge spécifiée
différence arithmétique entre la tension à vide d'un enroulement et la tension en charge aux bornes du même enroulement pour un courant de charge et un facteur de puissance spécifiés, la tension appliquée à l'autre (ou à l'un des autres) enroulement(s) étant égale:
- à sa valeur assignée, si le transformateur est connecté sur la prise principale (la tension à vide du premier enroulement étant alors égale à sa valeur assignée);
- à la tension de prise si le transformateur est connecté sur une autre prise.
Cette différence s'exprime généralement sous la forme d'un pourcentage de la tension à vide du premier enroulement
NOTE – Pour les transformateurs à plus de deux enroulements, la chute ou l'augmentation de tension dépend non seulement de la charge et du facteur de puissance de l'enroulement lui-même, mais aussi de la charge et du facteur de puissance des autres enroulements.
[IEV number 421-07-03]Тематики
Классификация
>>>EN
- voltage drop or rise for a specified load condition
- voltage regulation for a specified load condition
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > падение или повышение напряжения при заданном режиме нагрузки
-
10 первичная цепь
- Primärkreis, m
первичные цепи
Цепи основных технологических напряжений, по которым проходит основной поток энергии от источников к приемникам (потребителям). Назначение первичных цепей — выработка, преобразование, передача и распределение электрической энергии. Первичные цепи подразделяют на главную схему и собственные нужды.
[ http://www.baurum.ru/_library/?cat=electric-networks&id=3859]
Первичные цепи служат для осуществления энергетических функций: производства, передачи, распределения и потребления электроэнергии.
[ http://forca.ru/knigi/arhivy/puskonaladochnye-raboty-pri-montazhe-elektroustanovok-32.html]
первичная цепь
Цепь, непосредственно связанная с сетью переменного тока. Первичная цепь включает в себя средства связи с сетью переменного тока, например первичные обмотки трансформаторов, двигателей и других устройств.
[ ГОСТ Р МЭК 60838-1-2008]
первичная цепь
Цепь, непосредственно подключенная к сети питания переменного тока. она включает в себя, например, средства для соединения с сетью питания переменного тока, первичные обмотки трансформаторов, электродвигателей и других нагрузочных устройств.
Примечание - Проводящие части соединительных кабелей могут быть частью первичной цепи, как установлено в 1.2.11.6.
[ ГОСТ Р МЭК 60950-2002]EN
primary circuit
a circuit in an induction machine which, in service, receives active power from or delivers active power to the external electrical system
[ IEV ref 411-37-41]FR
circuit primaire
circuit d'une machine à induction qui, en service, reçoit de la puissance active du réseau électrique externe ou lui en fournit
[ IEV ref 411-37-41]Тематики
- электроснабжение в целом
- электротехника, основные понятия
EN
DE
- Primärkreis, m
FR
Русско-немецкий словарь нормативно-технической терминологии > первичная цепь
-
11 полное сопротивление относительно земли
полное сопротивление относительно земли
Полное сопротивление (импеданс) между точкой системы или установки, или оборудования и относительной землей на данной частоте.
[ ГОСТ Р МЭК 60050-195-2005]
полное сопротивление относительно земли
Полное сопротивление между определенной точкой системы или установки, или оборудования и эталонной землей на данной частоте.
[ ГОСТ Р МЭК 60050-826-2009]EN
impedance to earth
impedance at a given frequency between a specified point in a system or in an installation or in equipment and reference earth
[IEV number 195-01-17]
impedance to earth
impedance to ground (US)
impedance at a given frequency between a specified point in a system or in an installation or in equipment and reference earth
NOTE 1 – Reference earth is defined in IEC 60050-195. In practice, a reference point can be substituted to earth, for example the chassis.
NOTE 2 – The common mode rejection ratio of an instrument is dependent on the impedances between the input terminals and earth. Each of these impedances is called a common mode impedance.
Source: 195-01-17
[IEV number 312-06-20]FR
impédance de mise à la terre
impédance à une fréquence donnée entre un point spécifié d'un réseau, d'une installation ou d'un matériel et la terre de référence
[IEV number 195-01-17]
impédance de mise à la terre
impédance à une fréquence donnée entre un point spécifié d'un réseau, d'une installation ou d'un matériel et la terre de référence
NOTE 1 – La terre de référence est définie dans la CEI 60050-195. En pratique, on peut lui substituer un point de référence, par exemple la masse.
NOTE 2 – Le facteur de réjection de mode commun d'un appareil dépend de l'impédance entre chacune des bornes d'entrée et la terre. Chacune de ces impédances est appelée impédance de mode commun.
Source: 195-01-17
[IEV number 312-06-20]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > полное сопротивление относительно земли
-
12 принадлежность
принадлежность
<>аксессуар
-
[IEV number 151-11-24]EN
accessory
device supplementing a main device or apparatus, but not forming part of it, that is needed for its operation or to confer on it specific characteristics
[IEV number 151-11-24]FR
accessoire, m
dispositif supplémentaire qui ne fait pas partie d'un dispositif ou appareil principal mais qui est nécessaire à son fonctionnement ou pour lui apporter des caractéristiques particulières
[IEV number 151-11-24]EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > принадлежность
-
13 прямой пуск вращающегося электродвигателя
прямой пуск вращающегося электродвигателя
Пуск вращающегося электродвигателя путем непосредственного подключения его к питающей сети.
[ ГОСТ 27471-87]EN
direct-on-line starting
across-the-line starting (US)
the process of starting a motor by connecting it directly to the supply at rated voltage
[IEV number 411-52-15]FR
démarrage direct
mode de démarrage d'un moteur, consistant à lui appliquer directement sa pleine tension assignée
[IEV number 411-52-15]
Рис. ABB
Схема прямого пуска электродвигателяMagnetic only circuit-breaker - Автоматический выключатель с электромагнитным расцепителем
Contactor KL - Контактор KL
Thermal relay - Тепловое реле
Параллельные тексты EN-RU
Direct-on-line starting
Direct-on-line starting, which is often abbreviated as DOL, is perhaps the most traditional system and consists in connecting the motor directly to the supply network, thus carrying out starting at full voltage.Direct-on-line starting represents the simplest and the most economical system to start a squirrel-cage asynchronous motor and it is the most used.
As represented in Figure 5, it provides the direct connection to the supply network and therefore starting is carried out at full voltage and with constant frequency, developing a high starting torque with very reduced acceleration times.
The typical applications are relevant to small power motors also with full load starting.
These advantages are linked to some problems such as, for example, the high inrush current, which - in the first instants - can reach values of about 10 to 12 times the rated current, then can decrease to about 6 to 8 times the rated current and can persist to reach the maximum torque speed.The effects of such currents can be identified with the high electro-dynamical stresses on the motor connection cables and could affect also the windings of the motor itself; besides, the high inrush torques can cause violent accelerations which stress the transmission components (belts and joints) generating distribution problems with a reduction in the mechanical life of these elements.
Finally, also the possible electrical problems due to voltage drops on the supply line of the motor or of the connected equipment must be taken into consideration.
[ABB]Прямой пуск
Прямой пуск, который по-английски часто сокращенно обозначают как DOL, является, пожалуй наиболее распространенным способом пуска. Он заключается в непосредственном (т. е. прямом) подключении двигателя к питающей сети. Это означает, что пуск двигателя осуществляется при полном напряжении.Схема прямого пуска является наиболее простым, экономичным и чаще всего применяемым решением для электродвигателей с короткозамкнутым ротором.
Схема прямого подключения к сети представлена на рисунке 5. Пуск осуществляется при полном напряжении и постоянной частоте сети. Электродвигатель развивает высокий пусковой момент при коротком времени разгона.
Типичные области применения – маломощные электродвигатели, в том числе с пуском при полной нагрузке.
Однако, наряду с преимуществами имеются и определенные недостатки, например, бросок пускового тока, достигающий в первоначальный момент 10…12-кратного значения от номинального тока электродвигателя. Затем ток двигателя уменьшается примерно до 6…8-кратного значения номинального тока и будет держаться на этом уровне до тех пор, пока скорость двигателя не достигнет максимального значения.
Такое изменение тока оказывает значительное электродинамическое воздействие на кабель, подключенный к двигателю. Кроме того пусковой ток воздействует на обмотки двигателя. Высокий начальный пусковой момент может привести к значительному ускорению и следовательно к значительной нагрузке элементов привода (ремней, крепления узлов), что вызывает сокращение их срока службы.
И, наконец, следует принять во внимание возможное возникновение проблем, связанных с падением напряжения в линии питания двигателя и подключенного к этой линии оборудования.
[Перевод Интент]
Тематики
Синонимы
EN
- across-the-line starting (US)
- direct line starting
- direct operation of a motor
- direct starting
- direct-on-line starting
- DOL
- full voltage starter application
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > прямой пуск вращающегося электродвигателя
-
14 сверхток несрабатывания в главной цепи
сверхток несрабатывания в главной цепи
-
[IEV number 442-05-62]EN
non-operating overcurrent in the main circuit
Maximum value of current which can flow in the main circuit, in the absence of residual current, without causing operation of the detecting device of the residual current device as a consequence of asymmetry existing in the detecting device itself.
[IEV number 442-05-62]FR
surintensité de non-fonctionnement dans le circuit principal
Valeur maximale du courant pouvant circuler dans le circuit principal, en l'absence de courant différentiel résiduel, sans que le dispositif de détection du dispositif de coupure différentiel ne fonctionne en raison de la dissymétrie existant dans le dispositif de détection lui-même.
[IEV number 442-05-62]EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > сверхток несрабатывания в главной цепи
-
15 труба, не распространяющая горение
- nicht zur Flammenausbreitung beitragendes Elektroinstallationsrohr
- nicht flammverbreitendes Elektroinstallationsrohr
труба, не распространяющая горение
-
[IEV number 442-02-16]EN
non-flame propagating conduit
a conduit which is liable to ignite, as a result of an applied flame, but in which the flame does not propagate and which extinguishes itself within a limited time after the flame is removed
[IEV number 442-02-16]FR
conduit non propagateur de la flamme
conduit qui est susceptible de prendre feu lors de l'application d'une flamme, mais qui ne propage pas l'inflammation et s'éteint de lui même dans un temps réduit après retrait de la flamme
[IEV number 442-02-16]Тематики
- пожарная безопасность
- электропроводка, электромонтаж
EN
DE
- nicht flammverbreitendes Elektroinstallationsrohr
- nicht zur Flammenausbreitung beitragendes Elektroinstallationsrohr
FR
Русско-немецкий словарь нормативно-технической терминологии > труба, не распространяющая горение
-
16 трубная арматура, не распространяющая горение
- nicht zur Flammenausbreitung beitragendes Elektroinstallationsrohrformstück
- nicht flammverbreitendes Elektroinstallationsrohrformstück
трубная арматура, не распространяющая горение
-
[IEV number 442-02-27]EN
non-flame propagating conduit fitting
a conduit fitting which is liable to catch fire, as a result of an applied flame, but in which the flame does not propagate and which extinguishes itself within a limited time after the flame is removed
[IEV number 442-02-27]FR
accessoire de conduit non propagateur de la flamme
accessoire de conduit qui est susceptible de prendre feu lors de l'application d'une flamme, mais qui ne propage pas l'inflammation et s'éteint de lui même dans un temps réduit après retrait de la flamme
[IEV number 442-02-27]Тематики
- пожарная безопасность
- электропроводка, электромонтаж
EN
DE
- nicht flammverbreitendes Elektroinstallationsrohrformstück
- nicht zur Flammenausbreitung beitragendes Elektroinstallationsrohrformstück
FR
Русско-немецкий словарь нормативно-технической терминологии > трубная арматура, не распространяющая горение
-
17 упрочняющий покров
- Druckschutz, m
упрочняющий покров
Одно- или двухслойная обмотка из металлических лент или проволок, наложенная на оболочку кабеля давления для увеличения ее механической прочности.
[ ГОСТ 15845-80]
упрочняющий покров
ленты или проволоки, обычно из металла, накладываемые на оболочку для придания ей стойкости к механическим напряжениям вызываемым, как правило, внутренним давлением
[IEV number 461-05-05]EN
reinforcement
tapes or strips or wires, usually metallic, applied over a sheath to enable it to withstand mechanical stresses generally due to internal pressure
[IEV number 461-05-05]FR
frettage
rubans ou fils, généralement métalliques, appliqués sur une gaine pour lui permettre de supporter des contraintes mécaniques dues notamment à la pression interne
[IEV number 461-05-05]Тематики
- кабели, провода...
EN
DE
- Druckschutz, m
FR
Русско-немецкий словарь нормативно-технической терминологии > упрочняющий покров
-
18 экранирующий провод
экранирующий провод
отдельный провод или одножильный кабель, проложенный параллельно кабелю или кабельному каналу, являющийся частью замкнутой цепи, по которой могут проходить наведенные токи, магнитное поле которых будет противоположно полю в кабеле (ях)
[IEV number 461-12-01]EN
shielding conductor
separate conductor or single-core cable laid parallel to a cable or cable circuit and itself forming part of a closed circuit in which induced currents may flow whose magnetic field will oppose the field caused by the current in the cable(s)
[IEV number 461-12-01]FR
conducteur écran
conducteur de protection (déconseillé dans ce sens)
conducteur séparé ou câble à un conducteur posé parallèlement le long d'un câble ou d'un circuit de câbles et faisant lui-même partie d'un circuit fermé dans lequel peuvent circuler des courants induits dont le champ magnétique s'oppose à celui produit par les courants circulant dans le ou les câbles
[IEV number 461-12-01]Тематики
- кабели, провода...
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > экранирующий провод
-
19 электромагнитная совместимость технических средств
электромагнитная совместимость технических средств
ЭМС технических средств
Способность технического средства функционировать с заданным качеством в заданной электромагнитной обстановке и не создавать недопустимых электромагнитных помех другим техническим средством.
[ ГОСТ 30372—95 ]EN
electromagnetic compatibility
EMC (abbreviation)
the ability of an equipment or system to function satisfactorily in its electromagnetic environment without introducing intolerable electromagnetic disturbances to anything in that environment
Source: 702-08-66
[IEV number 161-01-07]FR
compatibilité électromagnétique
CEM (abréviation)
aptitude d'un appareil ou d'un système à fonctionner dans son environnement électromagnétique de façon satisfaisante et sans produire lui-même des perturbations électromagnétiques intolérables pour tout ce qui se trouve dans cet environnement
Source: 702-08-66
[IEV number 161-01-07]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > электромагнитная совместимость технических средств
См. также в других словарях:
lui — lui … Dictionnaire des rimes
lui — [ lɥi ] pron. pers. • XIe; lat. pop. illui, class. illi, datif de ille ♦ Pron. pers. de la 3e pers. du sing. I ♦ Pron. pers. des deux genres, représentant un nom de personne ou d animal (plur.⇒ 1. leur). 1 ♦ (Énon … Encyclopédie Universelle
lui — 1. (lui) 1° Pronom de la 3e personne qui est des deux genres et qui sert de régime indirect. Vous connaissez cette dame ; parlez lui. Vous lui remettrez cet argent, signifie également vous remettrez à un homme ou à une femme. • Il fallut le… … Dictionnaire de la Langue Française d'Émile Littré
Lui — (Französisch ihm) ist ein französisches Männermagazin. Geschichte Lui wurde vom Fotografen Daniel Filipacchi gegründet, der auf dem Prinzip des Playboy Magazins aufbauend ein Männermagazin mit französischem Charme entwickeln wollte. Der… … Deutsch Wikipedia
lui — pron., adj. său. (Vorba lui.) Trimis de siveco, 17.01.2007. Sursa: Sinonime nelalócul lui (ei, său etc.) loc. adj. Trimis de siveco, 10.08.2004. Sursa: Dicţionar ortografic … Dicționar Român
Lui — Nom porté dans le nord de l Italie, en particulier dans la province de Mantoue. Il semble correspondre au mot lüi , variante de luglio (= juillet) dans divers dialectes de cette région … Noms de famille
Lui — Lui, linker Nebenfluß des oberen Coango im westlichen Südafrika … Pierer's Universal-Lexikon
lui — [lat. volg. ĭllui, dativo di ille (per il class. illi ), sull analogia di cui ]. ■ pron. pers.m. sing. 1. a. [ha funzione di sogg. con valore per lo più marcato: l. stesso non ne è sicuro ] ▶◀ (lett.) egli, (ant.) ei. b. [come compl. ogg.: senti… … Enciclopedia Italiana
lui — LEUR, pr. pers. atone 3ème p. coi. ou ca. placé devant le v. : A1) lui (= à lui) ms. : d2c. / dc. psc. / e2c. : LO (Albanais 001, Annecy 003, Balme Sillingy 020, Côte Aime 188, Morzine 081b), le ou leu (081a, Aillon Vieux 273, Arêches 238,… … Dictionnaire Français-Savoyard
lui — 1lui pron.pers. di terza pers.m.sing., s.m.inv. I. pron.pers. di terza pers.m.sing. I 1a. FO usato come complemento oggetto e come complemento di termine, quando sia necessario conferire un certo rilievo, in luogo delle forme clitiche lo e gli,… … Dizionario italiano
lui — {{hw}}{{lui}}{{/hw}}A pron. pers. di terza pers. m. sing. 1 Indica la persona di cui si parla e si usa al posto di ‘egli’ ed ‘esso’, nei vari compl.: devi scrivere a lui; se io fossi in lui; vado con lui | Come compl. ogg. in luogo del pronome… … Enciclopedia di italiano