-
1 теплоотводящая поверхность корпуса подшипника
Русско-французский словарь нормативно-технической терминологии > теплоотводящая поверхность корпуса подшипника
-
2 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
3 каталитический конвертер
каталитический конвертер
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
catalytic converter
Catalytic converters are designed to clean up the exhaust fumes from petrol-driven vehicles, which are otherwise the major threat to air quality standards in congested urban streets and on motorways. Converters remove carbon monoxide, the unburned hydrocarbons and the oxides of nitrogen. These compounds are damaging to human health and the environment in a variety of ways. The converter is attached to the vehicle' s exhaust near the engine. Exhaust gases pass through the cellular ceramic substrate, a honeycomb-like filter. While compact, the intricate honeycomb structure provides a surface area of 23.000 square metres. This is coated with a thin layer of platinum, palladium and rhodium metals, which act as catalysts that simulate a reaction to changes in the chemical composition of the gases. Platinum and palladium convert hydrocarbons and carbon monoxide into carbon dioxide and water vapour. Rhodium changes nitrogen oxides and hydrocarbons into nitrogen and water, which are harmless. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > каталитический конвертер
-
4 площадь жилая
площадь жилая
Сумма площадей всех жилых помещений в квартире, общежитии или гостинице
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь жилая
-
5 площадь подсобная
площадь подсобная
Сумма площадей подсобных помещений в квартире - санузлов, кухонь, коридоров
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь подсобная
-
6 действующая площадь водосбора
действующая площадь водосбора
Часть площади водосбора, с которой осуществляется сток при данном слое осадков, поступающих на поверхность водосбора.
[ ГОСТ 19179-73]Тематики
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > действующая площадь водосбора
-
7 зона контакта шины с дорогой
зона контакта шины с дорогой
контакт шины с дорогой
Совокупность участков контакта, образованных наружными поверхностями выступов рисунка протектора с опорной поверхностью, и промежутков между ними.
[ ГОСТ 22374-77]Тематики
Обобщающие термины
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > зона контакта шины с дорогой
-
8 контурная площадь контакта
контурная площадь контакта
Fк
Площадь, ограниченная внешней огибающей участков контакта, образованных наружными поверхностями выступов рисунка протектора с опорной поверхностью.
[ ГОСТ 17697-72]
[ ГОСТ 22374-77]Тематики
- автомобили, качение колеса
- шины пневматические
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > контурная площадь контакта
-
9 площадь застройки
площадь застройки
Площадь горизонтального сечения по внешнему обводу здания на уровне цоколя, включая выступающие части, имеющие перекрытия - веранды, портики, галереи
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь застройки
-
10 площадь конструктивная
площадь конструктивная
Суммарная площадь горизонтальных сечений вертикальных конструкций
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь конструктивная
-
11 площадь контакта по выступам рисунка протектора
площадь контакта по выступам рисунка протектора
Fв
Сумма площадей контакта наружных поверхностей выступов рисунка протектора с опорной поверхностью.
[ ГОСТ 17697-72]
[ ГОСТ 22374-77]Тематики
- автомобили, качение колеса
- шины пневматические
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь контакта по выступам рисунка протектора
-
12 площадь общая
площадь общая
В производственных и общественных зданиях сумма площадей всех этажей, включая технические, измеряемых в пределах внутренних поверхностей наружных стен или там, где нет наружных стен – осей крайних колонн, а также площадей галерей, площадок, антресолей, рамп и переходов в другие здания
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь общая
-
13 площадь полезная
площадь полезная
Сумма жилой и подсобной площадей в квартире
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь полезная
-
14 площадь приведенная
площадь приведённая
Сумма полезной площади квартирного жилого дома, а также площадей лоджий, веранд, балконов с соответствующими понижающими коэффициентами
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- здания, сооружения, помещения
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь приведенная
-
15 площадь резервная
площадь резервная
Площадь территории, резервируемой для перспективного строительства
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- город, населенный пункт
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь резервная
-
16 площадь секториальная
площадь секториальная
Удвоенная площадь сектора, образованного начальным и подвижным радиус-векторами и траекторией перемещения точки на контуре сечения
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь секториальная
-
17 площадь стоянки на экипаж
площадь стоянки на экипаж
Площадь, занимаемая одним транспортным средством с учётом возможности его маневрирования
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- город, населенный пункт
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > площадь стоянки на экипаж
-
18 поверхность удельная
поверхность удельная
Отношение общей площади поверхности всех частиц материала к его объёму или массе
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > поверхность удельная
-
19 рабочая поверхность закрытого радионуклидного источника ионизирующего излучения
- surface d´émission de la source
рабочая поверхность закрытого радионуклидного источника ионизирующего излучения
рабочая поверхность источника
Поверхность или часть поверхности закрытого радионуклидного источника ионизирующего излучения, предназначенная для выхода ионизирующего излучения, используемого при эксплуатации источника.
[ ГОСТ 25504-82]Тематики
Синонимы
EN
DE
FR
- surface d´émission de la source
Русско-французский словарь нормативно-технической терминологии > рабочая поверхность закрытого радионуклидного источника ионизирующего излучения
-
20 загрязнение (в электробезопасности)
загрязнение
Присутствие инородного вещества: твердого, жидкого или газообразного (ионизированные газы), - которое может вызвать уменьшение диэлектрической прочности или поверхностного сопротивления.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
загрязнение
Любое добавление инородных веществ, твердых, жидких или газообразных (ионизированных газов), которые могли бы уменьшить электрическую прочность изоляции или удельное сопротивление поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
pollution
any condition of foreign matter, solid, liquid or gaseous (ionized gases), that may affect dielectric strength or surface resistivity
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
any addition of foreign matter, solid, liquid or gaseous that can produce a permanent reduction of dielectric strength or surface resistivity of the insulation
NOTE – Ionized gases of a temporary nature are not considered as to be a pollution.
[IEV number 442-01-28]
contamination
the first is defined as area and the second as particulate. The first is caused by surface contaminants that cannot be removed by cleaning or are stained after cleaning. Those may be foreign matter on the surface of, for example a localized area that is smudged, stained, discoloured, mottled, etc., or large areas exhibiting a hazy or cloudy appearance resulting from a film of foreign materials
[IEC 62276, ed. 1.0 (2005-05)]FR
pollution
tout apport de matériau étranger solide, liquide ou gazeux (gaz ionisés) qui peut entraîner une réduction de la rigidité diélectrique ou de la résistivité de la surface
[IEC 60947-1, ed. 5.0 (2007-06)]
pollution
tout apport de matériau étranger solide, liquide ou gazeux qui peut entraîner une réduction permanente de la rigidité diélectrique ou de la résistivité de surface de l'isolation
NOTE – Les gaz ionisés de nature fugace ne sont pas considérés comme une pollution.
[IEV number 442-01-28]
Тематики
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > загрязнение (в электробезопасности)
- 1
- 2
См. также в других словарях:
Surface area — is the measure of how much exposed area an object has. It is expressed in square units. If an object has flat faces, its surface area can be calculated by adding together the areas of its faces. Even objects with smooth surfaces, such as spheres … Wikipedia
surface area — surface ,area noun count the total area of a surface or surfaces, especially the outside surfaces of an object: enough paint to cover a surface area of 900 square feet … Usage of the words and phrases in modern English
surface pressure-surface area isotherm — Surface Pressure Surface Area Isotherm Изотерма поверхностное давление площадь Зависимость поверхностного давления монослоя Ленгмюра на поверхности водной субфазы от площади, занимаемой молекулами поверхностно активного вещества в этом… … Толковый англо-русский словарь по нанотехнологии. - М.
surface area — surface .area n the area of the outside of an object that can be measured … Dictionary of contemporary English
Surface area to volume ratio — In chemical reactions involving a solid material, the surface area to volume ratio is an important factor for the reactivity, that is, the rate at which the chemical reaction will proceed. In some industries it is abbreviated sa/vol.Physical… … Wikipedia
surface area — noun the extent of a 2 dimensional surface enclosed within a boundary (Freq. 2) the area of a rectangle it was about 500 square feet in area • Syn: ↑area, ↑expanse • Derivationally related forms: ↑areal ( … Useful english dictionary
surface area — UK / US noun [countable] Word forms surface area : singular surface area plural surface areas maths the total area of a surface or surfaces, especially the outside surfaces of an object enough paint to cover a surface area of 900 square feet … English dictionary
surface area — paviršiaus plotas statusas T sritis Standartizacija ir metrologija apibrėžtis Nagrinėjamojo paviršiaus plotas. atitikmenys: angl. surface area vok. Oberflächeninhalt, m rus. площадь поверхности, f pranc. aire de surface, f … Penkiakalbis aiškinamasis metrologijos terminų žodynas
surface area — paviršiaus plotas statusas T sritis fizika atitikmenys: angl. surface area vok. Oberflächeninhalt, m rus. площадь поверхности, f pranc. aire de surface, f … Fizikos terminų žodynas
Surface area, volume, and average depth of oceans and seas — ▪ Table Surface area, volume, and average depth of oceans and seas area volume average depth 000,000 sq km 000,000 sq mi 000,000 cu km 000,000 cu mi m ft Atlantic Ocean without marginal seas 82.440 31.830 324.600 77.900 3,930 12,890 with… … Universalium
Accessible surface area — Illustration of the solvent accessible surface in comparison to the van der Waals surface. The van der Waals surface as given by the atomic radii is shown in red. The accessible surface is drawn with dashed lines and is created by tracing the… … Wikipedia