-
1 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
-
2 измеренное значение параметра
измеренное значение параметра
Значение параметра, установленное в результате его измерения определенным средством контроля.
[ ГОСТ 19919-74]EN
measured value
physical or electrical quantity, property or condition that is to be measured
NOTE 1 Measured values are usually monitored, but may be calculated from other values. They are also usually considered to be analogue values.
NOTE 2 The result of a sampling of an analogue magnitude of a particular quantity.
[IEC 61850-7-4]
measured value
estimate of the true value of a quantity, derived from the indicated value of a meter after applying all relevant correction factors
[IEC 60788, ed. 2.0 (2004-02)]
measured value
best estimate of the true value of a quantity, being derived from the indicated value of an instrument together with the application of all relevant correction factors and the calibration factor
Note 1 to entry: The measured value is sometimes also referred to as result of a measurement
[IEC 61674, ed. 2.0 (2012-11)]FR
valeur mesurée
meilleure estimation de la valeur vraie d'une grandeur, qui est déduite de la valeur indiquée par un instrument ainsi que de l'application de tous les facteurs de correction appropriés et du facteur d’étalonnage
Note 1 à l'article: La valeur mesurée est parfois également désignée par «résultat d’une mesure».
[IEC 61674, ed. 2.0 (2012-11)]Значение регулируемой величины, полученное в рассматриваемый момент времени на основании данных некоторого измерительного прибора называется ее измеренным значением.
[ http://infor.wallst.ru/5/ab3.htm]Тематики
- контроль автоматизир. тех. состояния авиац. техники
- электротехника, основные понятия
Обобщающие термины
- параметры контроля, их значения и определение
Синонимы
EN
FR
Русско-французский словарь нормативно-технической терминологии > измеренное значение параметра
-
3 номинальное напряжение изоляции (аппарата), Ui
номинальное напряжение изоляции (аппарата), Ui
Значение напряжения, по которому определяют испытательное напряжение при испытании изоляционных свойств, расстояние утечки и воздушные зазоры.
Максимальное значение номинального рабочего напряжения не должно превышать наибольшего значения номинального напряжения изоляции.
Примечание — Для аппарата, у которого номинальное напряжение изоляции не устанавливается, его следует принимать как наибольшее значение любого номинального напряжения
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
rated insulation voltage, Ui
value of voltage to which dielectric tests and creepage distances are referred
[IEC 62314, ed. 1.0 (2006-05)]
rated insulation voltage (RIV)
voltage value assigned by the manufacturer to the equipment or to a part of it, characterizing the specified (long-term) withstand capability of its insulation
NOTE 1 The rated insulation voltage is higher than or equal to the rated voltage of the equipment, or to the rated voltage of the concerned part of the equipment, which is primarily related to functional performance.
NOTE 2 The rated insulation voltage refers to the insulation between electric circuits, between live parts and exposed conductive parts and within an electric circuit.
NOTE 3 For clearances and solid insulation, the peak value of the voltage occurring across the insulation or clearance is the determining value for the rated insulation voltage. For creepage distances the r.m.s. value is the determining value
[IEC 62103, ed. 1.0 (2003-07)]FR
tension assignée d'isolement (TIA)
valeur efficace de la tension de tenue fixée par le constructeur au matériel ou à une de ses parties, caractérisant la capacité de tenue spécifiée (à long terme) de son isolation
NOTE 1 La tension assignée d'isolement est supérieure ou égale à la tension assignée du matériel ou de la partie concernée de l’appareil qui est principalement liée aux caractéristiques fonctionnelles.
NOTE 2 La tension d'isolement assignée se rapporte à l'isolation entre circuits électriques, entre parties conductrices et masses, et à l'intérieur du circuit électrique.
NOTE 3 Pour les distances d'isolement et pour les isolants solides, la tension d'isolement assignée est déterminée par la valeur de crête de la tension apparaissant aux bornes de l'isolant ou de la distance. Pour les lignes de fuites, c'est la tension efficace qu'il faut prendre
[IEC 62103, ed. 1.0 (2003-07)]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
EN
- rated insulation voltage
- rated insulation voltage, Ui
- RIV
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение изоляции (аппарата), Ui
-
4 постоянная (счетчика)
постоянная (счетчика)
-
[IEV number 314-07-08]EN
(meter) constant
value expressing the relation between the active energy registered by a meter and the corresponding value of the test output.
NOTE – If this value is a number of pulses, the constant should be either pulses per kilowatt-hour (imp/kWh) or watt-hours per pulse (Wh/imp)
[IEV number 314-07-08]FR
co nstante (du compteur)
valeur exprimant la relation entre l’énergie enregistrée par un compteur et la valeur correspondante donnée par le dispositif de sortie d’essai
NOTE – Si cette valeur est un nombre d’impulsions, la constante doit être soit le nombre d’impulsions par kilowattheure (imp/kWh), soit le nombre de wattheures par impulsion (Wh/imp)
[IEV number 314-07-08]Тематики
- измерение электр. величин в целом
- счетчик электроэнергии
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > постоянная (счетчика)
-
5 номинальное значение
номинальное значение
Количественное значение, указанное, как правило, изготовителем для определенного рабочего состояния детали, устройства или аппарата.
МЭК 60050(151-04-03).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
номинальное значение
Значение величины, установленное обычно изготовителем для определенных рабочих условий компонента, прибора или оборудования.
[ ГОСТ Р 52319-2005 (МЭК 60050-151 [10], позиция 151-04-03)]
номинальное значение
Значение параметра электротехнического изделия (устройства), указанное изготовителем, при котором оно должно работать, являющееся исходным для отсчета отклонений.
Примечание
К числу параметров относятся, например, ток, напряжение, мощность.
[ ГОСТ 18311-80]
номинальное значение
-
[IEV number 442-01-01]EN
nominal value
value of a quantity used to designate and identify a component, device, equipment, or system
NOTE – The nominal value is generally a rounded value.
[IEV number 151-16-09]
rated value
a quantity value assigned, generally by a manufacturer, for a specified operating condition of a component, device or equipment
Source: 151-04-03
[IEV number 442-01-01]FR
valeur nominale, f
valeur de dénomination, f
valeur d'une grandeur, utilisée pour dénommer et identifier un composant, un dispositif, un matériel ou un système
NOTE – La valeur nominale est généralement une valeur arrondie.
[IEV number 151-16-09]
valeur assignée
valeur d'une grandeur fixée, généralement par le constructeur, pour un fonctionnement spécifié d'un composant, d'un dispositif ou d'un matériel
Source: 151-04-03
[IEV number 442-01-01]Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > номинальное значение
-
6 истинное значение физической величины
- valeur vraie (d´une grandeur)
истинное значение физической величины
истинное значение величины
истинное значение
Значение физической величины, которое идеальным образом характеризует в качественном и количественном отношении соответствующую физическую величину.
Примечание. Истинное значение физической величины может быть соотнесено с понятием абсолютной истины. Оно может быть получено только в результате бесконечного процесса измерений с бесконечным совершенствованием методов и средств измерений.
[РМГ 29-99]
истинное значение
Значение, идеально характеризующее конкретную физическую величину при условиях, существующих в момент рассмотрения данной величины.
[МЭК 359,4.1].
[ ГОСТ Р 61557-1-2006]EN
true value
value of the physical quantity to be measured by an instrument
[IEC 62467-1, ed. 1.0 (2009-06)]
true value
value of a quantity which is defined with no uncertainty.
NOTE The true value of a quantity is an ideal concept and, in general, cannot be known exactly.
[IEC 60746-1, ed. 2.0 (2003-01)]FR
valeur vraie
valeur d’une grandeur physique à mesurer avec un instrument
[IEC 62467-1, ed. 1.0 (2009-06)]
valeur vraie
valeur qui caractérise une quantité parfaitement définie dans les conditions qui existent lorsque cette quantité est considérée
NOTE La valeur vraie d’une quantité est une notion théorique et, en général, ne peut être connue exactement, mais estimée par mesure.
[IEC 60068-3-11, ed. 1.0 (2007-05)]
Тематики
- метрология, основные понятия
Синонимы
EN
DE
FR
- valeur vraie (d´une grandeur)
Русско-французский словарь нормативно-технической терминологии > истинное значение физической величины
-
7 значение величины срабатывания (возврата) электрического реле
значение величины срабатывания (возврата) электрического реле
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
[ ГОСТ 16022-83]EN
switching value
the value of the input energizing quantity (or characteristic quantity) at which a relay switches under specified conditions
NOTE – These specified conditions can be expressed by using one of the adjectives defined under the items 446-13-27 to 446-13-29.
[IEV number 446-13-24]FR
valeur de commutation
valeur de la grandeur d'alimentation d'entrée ou de la grandeur caractéristique, pour laquelle un relais commute dans des conditions spécifiées
NOTE – Ces conditions spécifiées peuvent être exprimées par l'un des qualificatifs définis de 446-13-27 à 446-13-29.
[IEV number 446-13-24]Тематики
Классификация
>>>EN
DE
FR
71. Значение величины срабатывания (возврата) электрического реле
D. Ansprechwert
Е. Operate value
F. Valeur de fonctionnement
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > значение величины срабатывания (возврата) электрического реле
-
8 нормируемый параметр невозврата электрического реле
нормируемый параметр невозврата электрического реле
Значение входной воздействующей или характеристической величины, при котором электрическое реле не должно возвращаться
[ ГОСТ 16022-83]EN
non-release value
the value of the input energizing quantity (or characteristic quantity) at which a relay does not release under specified conditions
NOTE – These specified conditions can be expressed by using one of the adjectives defined under the items 446-13-27 to 446-13-29.
[IEV number 446-13-18 ]FR
valeur de non-relâchement
valeur de la grandeur d'alimentation d'entrée ou de la grandeur caractéristique pour laquelle un relais ne relâche pas dans des conditions spécifiées
NOTE – Ces conditions spécifiées peuvent être exprimées par l'un des qualificatifs définis de 446-13-27 à 446-13-29.
[IEV number 446-13-18 ]Тематики
Классификация
>>>EN
DE
FR
74. Нормируемый параметр невозврата электрического реле
D. Haltwert
Е. Non-release value
F. Valeur de non relâchement
Значение входной воздействующей или характеристической величины, при котором электрическое реле не должно возвращаться
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > нормируемый параметр невозврата электрического реле
-
9 входное полное сопротивление
входное полное сопротивление
-
[IEV number 312-06-18]EN
input impedance
impedance of the input circuit measured between the input terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the input circuit is such that the instantaneous value of the current flowing into the input terminals is a non-linear function of the instantaneous value of the input voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual input circuit, is sometimes called the "equivalent input impedance".
[IEV number 312-06-18]FR
impédance du circuit d'entrée
impédance du circuit d'entrée entre les bornes d'entrée dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit d'entrée est tel que la valeur instantanée du courant traversant les bornes d'entrée est une fonction non linéaire de la valeur instantanée de la tension d'entrée dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit d'entrée réel, est parfois appelée "impédance équivalente d'entrée".
[IEV number 312-06-18]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > входное полное сопротивление
-
10 выходное полное сопротивление
выходное полное сопротивление
-
[IEV number 312-06-19]EN
output impedance
impedance of the output circuit measured between the output terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the output circuit is such that the instantaneous value of the current flowing into the output terminals is a non-linear function of the instantaneous value of the output voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual output circuit, is sometimes called the "equivalent output impedance".
[IEV number 312-06-19]FR
impédance du circuit de sortie
impédance du circuit de sortie entre les bornes de sortie dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit de sortie est tel que la valeur instantanée du courant traversant les bornes de sortie est une fonction non linéaire de la valeur instantanée de la tension de sortie dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit de sortie réel, est parfois appelée "impédance équivalente de sortie".
[IEV number 312-06-19]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выходное полное сопротивление
-
11 интергармоника
интергармоника
Интергармониками называют токи (напряжения) частота которых не кратна частоте основной гармоники.EN
interharmonic component
sinusoidal component of a periodic quantity having a an interharmonic frequency
NOTE 1 For brevity, such a component may be referred to simply as an interharmonic.
NOTE 2 For practical analysis, an approximation of the periodicity may be necessary.
NOTE 3 The value is normally expressed as an r.m.s. value.
NOTE 4 As stated in IEC 61000-4-7, the time window has a width of 10 fundamental periods (50 Hz systems) or 12 fundamental periods (60 Hz systems), i.e. approximately 200 ms. The difference in frequency between two consecutive interharmonic components is, therefore, approximately 5 Hz. In the case of other fundamental frequencies, the time window should be selected between 6 fundamental periods (approximately 1 000 ms at 6 Hz) and 18 fundamental periods (approximately 100 ms at 180 Hz).
[IEC 60146-1-1, ed. 4.0 (2009-06)]FR
composante interharmonique
composante sinusoïdale d’une grandeur périodique dont la fréquence est une fréquence interharmonique
NOTE 1 Pour des raisons de concision, ce type de composante peut être désigné simplement par le terme « interharmonique ».
NOTE 2 Pour l’analyse pratique, il peut être nécessaire de procéder à une approximation de la périodicité.
NOTE 3 La valeur est normalement exprimée comme une valeur efficace.
NOTE 4 Comme indiqué dans la CEI 61000-4-7, la fenêtre temporelle a une largeur de 10 périodes fondamentales (systèmes de 50 Hz) ou de 12 périodes fondamentales (systèmes de 60 Hz), c’est-à-dire approximativement 200 ms. La différence de fréquence entre deux composantes interharmoniques consécutives est, par conséquent, d’environ 5 Hz. Dans le cas d’autres fréquences fondamentales, il convient de choisir la fenêtre temporelle entre 6 périodes fondamentales (environ 1 000 ms à 6 Hz) et 18 périodes fondamentales (environ 100 ms à 180 Hz). [IEC 60146-1-1, ed. 4.0 (2009-06)]
На частотах, расположенных между частотами гармонических составляющих тока и напряжения, могут наблюдаться интергармоники. Интергармоники могут возникать на дискретных частотах или иметь спектральные составляющие в достаточно широкой полосе частот. Суммарное воздействие различных источников интергармоник маловероятно и в настоящем стандарте не учитывается.
Полного понимания природы электромагнитных возмущений, ассоциирующихся с интергармониками, еще нет, и в настоящее время к этому явлению возник повышенный интерес. Интергармоники всегда присутствуют в системе электроснабжения, но в последнее время с резким увеличением силовых электронных систем их практическое влияние стало более ощутимым.
[Збигнев Ханзелка (Zbigniew Hanzelka), Анжей Бьень (Andrzej Bien) AGH-UST, Краков, Республика Польша. Энергосбережение №7/2005]Тематики
Действия
Синонимы
EN
FR
Русско-французский словарь нормативно-технической терминологии > интергармоника
-
12 классификационный ток ОПН
классификационный ток ОПН
Iкл
Амплитудное значение (более высокое амплитудное значение из двух полярностей, если ток асимметричен) активной составляющей тока промышленной частоты, которое используется для определения классификационного напряжения ОПН и нормируется изготовителем.
[ ГОСТ Р 52725-2007]EN
reference current of an arrester
peak value (the higher peak value of the two polarities if the current is asymmetrical) of the resistive component of a power-frequency current used to determine the reference voltage of the arrester
NOTE 1 The reference current will be high enough to make the effects of stray capacitances at the measured reference voltage of the arrester units (with designed grading system) negligible and is to be specified by the manufacturer.
NOTE 2 Depending on the nominal discharge current and/or line discharge class of the arrester, the reference current will be typically in the range of 0,05 mA to 1,0 mA per square centimetre of disc area for single column arresters.
[IEC 60099-4, ed. 2.0 (2004-05)]FR
courant de référence d'un parafoudre
valeur de crête (la plus grande des deux polarités si le courant est dissymétrique) de la composante résistive du courant à fréquence industrielle utilisée pour déterminer la tension de référence d'un parafoudre.
NOTE 1 Il convient que le courant de référence soit suffisamment élevé pour rendre négligeables les effets des capacités parasites aux tensions de référence mesurées sur les éléments de parafoudre (avec leur système de répartition) et qu’il soit spécifié par le constructeur.
NOTE 2 Fonction du courant de décharge nominal et/ou de la classe de décharge de ligne du parafoudre, il convient que le courant de référence soit typiquement dans la gamme de 0,05 mA à 1,0 mA par centimètre carré de surface de disque pour les parafoudres à colonne unique
[IEC 60099-4, ed. 2.0 (2004-05)]Тематики
- высоковольтный аппарат, оборудование...
EN
FR
Русско-французский словарь нормативно-технической терминологии > классификационный ток ОПН
-
13 сверхпереходное реактивное сопротивление по поперечной оси
сверхпереходное реактивное сопротивление по поперечной оси
-EN
quadrature-axis sub-transient reactance
the quotient of the initial value of a sudden change in that fundamental a.c. component of armature voltage, which is produced by the total quadrature-axis primary flux and the value of the simultaneous change in fundamental a.c. component of quadrature-axis armature current, the machine running at rated speed
[IEV ref 411-50-12]FR
réactance subtransitoire transversale
quotient de la valeur initiale d'une variation brusque du terme fondamental de la composante de la tension d'induit, produite par le flux transversal total, par la valeur de la variation simultanée du terme fondamental de la composante du courant d'induit transversal, la machine tournant à sa vitesse assignée
[IEV ref 411-50-12]Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > сверхпереходное реактивное сопротивление по поперечной оси
-
14 синхронное реактивное сопротивление по продольной оси
синхронное реактивное сопротивление по продольной оси
-EN
direct-axis synchronous reactance
the quotient of the sustained value of that fundamental a.c. component of armature voltage, which is produced by the total direct-axis primary flux due to direct-axis armature current, and the value of the fundamental a.c. component of this current, the machine running at rated speed
[IEV ref 411-50-07]FR
réactance synchrone longitudinale
quotient de la valeur, en régime établi, du terme fondamental de la composante de la tension d'induit produite par le flux longitudinal total dû au courant d'induit longitudinal, par la valeur du terme fondamental de ce courant, la machine tournant à sa vitesse assignée
[IEV ref 411-50-07]
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > синхронное реактивное сопротивление по продольной оси
-
15 остаточное напряжение
остаточное напряжение
Ures
Минимальное значение напряжения Urms(1/2) или Urms(1), зарегистрированное во время провала или прерывания напряжения.
Примечание. Значение остаточного напряжения выражают в вольтах, процентах или долях входного напряжения Udin. Для класса A характеристик процесса измерения применяют Urms(1/2), для класса S допускается применять Urms(1/2) или Urms(1) (см. 5.4.1).
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
residual voltage
Ures
minimum value of Urms(1/2) or Urms(1) recorded during a voltage dip or interruption
NOTE The residual voltage is expressed as a value in volts, or as a percentage or per unit value of Udin. Urms(1/2) is used for Class A. Either Urms(1/2) or Urms(1) may be used for Class S.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension résiduelle
Ures
valeur minimale de Ueff(1/2) ou Ueff(1) enregistrée au cours d’un creux ou d’une coupure de tension
NOTE La tension résiduelle est exprimée sous la forme d’une valeur, exprimée en volts, ou d’un pourcentage ou par unité de Udin. Ueff(1/2) est utilisé pour la classe A. Ueff(1/2) ou Ueff(1) peuvent être utilisés pour la classe S. Voir 5.4.1.
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
Синонимы
EN
FR
Русско-французский словарь нормативно-технической терминологии > остаточное напряжение
-
16 эталонное значение влияющей величины
эталонное значение влияющей величины
-
[IEV number 442-05-36]EN
reference value of an influencing quantity
the value of an influencing quantity to which the manufacturer's stated characteristics are referred
[IEV number 442-05-36]FR
valeur de référence d'une grandeur d'influence
valeur d'une grandeur d'influence à laquelle sont rapportées les caractéristiques indiquées par le constructeur
[IEV number 442-05-36]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > эталонное значение влияющей величины
-
17 время дифференцирования
время предварения
время дифференцирования
Время, в течение которого входной сигнал, изменяющийся с постоянной скоростью, достигнет значения выходного сигнала, изменяющегося с той же скоростью, в момент начала отсчета.
[ ГОСТ 9988-84]EN
derivative action time
for a derivative element the same as the derivative action coefficient, if its input and output variables have the same unit
Note 1 – Then the derivative action time is given by TD = KD, where KD is the derivative action coefficient.
Note 2 – The derivative action time can also be given as the duration of the time interval that a rampwise variation of the input variable needs to reach the same value as the stepwise varying output variable.
[IEV ref 351-28-26]FR
constante de temps de dérivation
pour un élément à action par dérivation, la constante de temps de dérivation est égale au coefficient d'action par dérivation, si ses variables d'entrée et de sortie sont dans la même unité
Note 1 – La constante de temps de dérivation est alors donnée par TD = KD, où KD est le coefficient d'action par dérivation.
Note 2 – La constante de temps de dérivation peut également être donnée comme la durée de l'intervalle de temps nécessaire pour qu'une variation en rampe de la variable d'entrée atteigne la même valeur que la variable de sortie correspondante.
[IEV ref 351-28-26]Тематики
- автоматизация, основные понятия
Синонимы
EN
DE
- Differenzierzeit, f
FR
Русско-французский словарь нормативно-технической терминологии > время дифференцирования
-
18 время интегрирования
время интегрирования
Время, в течение которого интегральная составляющая регулятора изменяет выходной сигнал на значение, равное значению скачкообразного изменения входного сигнала.
[ ГОСТ 9988-84]EN
integral action time
for an integral element, the reciprocal of the integral action coefficient, if its input and output variables have the same unit
Note 1 – The integral action time then is given by
TI=1/KI
where KI is the integral action coefficient.
Note 2 – The integral action time can also be given as that duration of the time interval which the output variable needs to reach the same value as a stepwise variation of the input variable.
[IEV ref 351-28-21]FR
constante de temps d'intégration
pour un élément à action par intégration, inverse du coefficient d'action par intégration, si ses variables d'entrée et de sortie sont dans la même unité
Note 1 – La constante de temps d'intégration est alors donnée par
TI=1/KI
où KI est le coefficient d'action par intégration.
Note 2 – La constante de temps d'intégration peut également être donnée comme la durée de l'intervalle de temps nécessaire pour que la variable de sortie atteigne la même valeur qu'une variation en échelon de la variable d'entrée.
[IEV ref 351-28-21]Тематики
- автоматизация, основные понятия
EN
DE
- Integrierzeit, f
FR
Русско-французский словарь нормативно-технической терминологии > время интегрирования
-
19 доход
мrevenu, gain; бухг. résultat; (от капитальных, финансовых операций) produit, plus-value; ( поступления) recette(s); см. тж выручка, поступление, прибыльполучать доход — réaliser un revenu, tirer un revenu, percevoir un revenu
приносить доход — см. давать доход
не приносящий дохода — non rentable, non profitable
приносящий доход — rentable, profitable
неосновной доход от предпринимательской деятельности — produit exceptionnel, résultat exceptionnel
основной доход от предпринимательской деятельности — produit d'exploitation, résultat d'exploitation
- доходы бюджетадоход, полученный нечестным путём — revenu crapuleux, gain illicite
- доход в валюте
- доход в виде процентов
- доход в денежном выражении
- доход в денежном исчислении
- доход в натуральном выражении
- доход в натуральной форме
- доход в неизменных ценах
- доход в расчёте на акцию
- доход в текущих ценах
- доход в форме наличности
- доходы госбюджета
- доход до уплаты налогов
- доход за вычетом налогов
- доходы лиц наёмного труда
- доход на акцию
- доход на душу населения
- доходы населения
- доход нетто-процентный
- доход от акций
- доход от аренды
- доход от биржевых операций
- доход от владения имуществом
- доход от вложений
- доход от внешней торговли
- доход от деятельности
- доход от земельной собственности
- доход от инвестиций
- доход от налогов
- доход от недвижимости
- доход от нематериальных активов
- доход от облигаций
- доход от передачи
- доход от портфельных инвестиций
- доход от посредничества
- доход от продаж
- доход от реализации
- доход от валовой реализации
- доход от сбережений
- доход от собственности
- доход от страхования
- доход от торговли
- доход от торговой деятельности
- доход от трудовой деятельности
- доход от туризма
- доход от фактора производства
- доход от финансовых операций
- доход от ценных бумаг
- доход от эксплуатации имущества
- доход от экспорта
- доход после уплаты налогов
- доходы предприятия
- доход предшествующего периода
- прочие доходы
- доход, ранее полученный
- доходы резидентов
- доход с капитала
- доход семьи
- брутто-процентный доход
- бюджетный доход
- валовой доход
- валовой доход от реализации
- валютный доход
- вменённый доход
- внеплановые доходы
- гарантированный доход
- годовой доход
- государственные доходы
- декларированный доход
- денежный доход
- дивидендный доход
- добавочный доход
- дополнительный доход
- душевой доход
- ежедневный доход
- заранее распределённый доход
- заявленный доход
- избыточный доход
- инвалютный доход
- индексированный доход
- личный
- месячный доход
- монопольный доход
- накопленный доход
- наличный доход
- налоговый доход
- налогооблагаемый доход
- национальный доход
- начисленный доход
- начисляемый доход
- невыплаченный доход
- незаконный доход
- нематериальный доход
- нераспределённый доход
- номинальный доход
- доход, облагаемый налогом
- обычный доход
- объявленный доход
- ожидаемый доход
- операционный доход
- оптимальный доход
- основной доход
- относительный доход
- падающий доход
- первичный доход
- первоначальный доход
- перечисленный доход
- перманентный доход
- плановый доход
- пожизненный доход
- полученный доход
- постоянный доход
- поступивший доход
- потенциальный доход
- потребительский доход
- потреблённый доход
- предельный доход
- предполагаемый доход
- предпринимательский доход
- предшествующий доход
- доход, приносимый собственностью
- производный доход
- процентный доход
- прямой доход
- растущий доход
- расчётный доход
- реальный доход
- реинвестированный доход
- рентный доход
- случайный доход
- совокупный доход
- сокращающийся доход
- среднедушевой доход
- средний доход
- стабильный доход
- текущий доход
- трудовой доход
- упущенный доход
- устойчивый доход
- фактический доход
- фиксированный доход
- фискальные доходы
- чистый доход -
20 линейное преобразование
линейное преобразование
-
[IEV number 314-02-04]EN
linear conversion
conversion for which the quotient of each change in the output value by the corresponding change in the input value is intended to be constant
[IEV number 314-02-04]FR
conversion linéaire
conversion telle que le quotient de chaque changement de la valeur de sortie par le changement correspondant de la valeur d'entrée soit constant
[IEV number 314-02-04]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > линейное преобразование
См. также в других словарях:
par/par value — n. Equality between face value and actual selling price. Webster s New World Law Dictionary. Susan Ellis Wild. 2000 … Law dictionary
Par value — Par value, in finance and accounting, means stated value or face value. From this comes the expressions at par (at the par value), over par (over par value) and under par (under par value). The term par value has several meanings depending on… … Wikipedia
par value — n: par(a) Merriam Webster’s Dictionary of Law. Merriam Webster. 1996. par value … Law dictionary
Par value — Par Par, n. [L. par, adj., equal. See {Peer} an equal.] [1913 Webster] 1. Equal value; equality of nominal and actual value; the value expressed on the face or in the words of a certificate of value, as a bond or other commercial paper. [1913… … The Collaborative International Dictionary of English
par value — n. the value of a stock, bond, etc. fixed at the time of its issue; face value: distinguished from MARKET VALUE * * * … Universalium
par-value stock — Shares in a corporation that were given a stated share price (par value) when issued. Compare: no par stock Category: Business, LLCs & Corporations → LLCs, Corporations, Partnerships, etc. Nolo’s Plain English Law Dictionary. Gerald N. Hill,… … Law dictionary
par value — n. the value of a stock, bond, etc. fixed at the time of its issue; face value: distinguished from MARKET VALUE … English World dictionary
par value — See par for all securities except MBSs. See par line for MBSs. American Banker Glossary Also called the maturity value or face value; the amount that an issuer agrees to pay at the maturity date. Bloomberg Financial Dictionary See … Financial and business terms
Par value — Also called the maturity value or face value, the amount that the issuer agrees to pay at the maturity date. The New York Times Financial Glossary * * * par value par value ➔ value1 * * * The value that appears on the face of a document… … Financial and business terms
par value — The value of an instrument for the payment of money as determined by the face of the instrument. The face value of a bond. An amount fixed as the nominal value of a share of corporate stock, such amount indicating the sum of money or value of… … Ballentine's law dictionary
Par Value — 1. The face value of a bond. 2. A dollar amount that is assigned to a security when representing the value contributed for each share in cash or goods. 1. The par values for different fixed income products will vary. Bonds generally have a par… … Investment dictionary