Перевод: с русского на немецкий

с немецкого на русский

most+of+all

  • 1 длительный допустимый ток

    1. Strombelastbarkeit, f
    2. Dauerstrombelastbarkeit, f

     

    (длительный) допустимый ток
    Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
    [ ГОСТ Р МЭК 60050-826-2009]

    Этот ток обозначают IZ
    [ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]

    EN

    (continuous) current-carrying capacity
    ampacity (US)
    maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
    [IEV number 826-11-13]

    ampacity
    The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
    [National Electrical Cod]

    FR

    courant (permanent) admissible, m
    valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
    [IEV number 826-11-13]

    Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:

    • its insulation temperature rating;
    • conductor electrical properties for current;
    • frequency, in the case of alternating currents;
    • ability to dissipate heat, which depends on cable geometry and its surroundings;
    • ambient temperature.

    Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.

    The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.

    In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.

    Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.

    The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.

    For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.

    Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.

    When designing an electrical system, one will normally need to know the current rating for the following:

    Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.

    [http://en.wikipedia.org/wiki/Ampacity]

    Тематики

    • электротехника, основные понятия

    Синонимы

    EN

    DE

    • Dauerstrombelastbarkeit, f
    • Strombelastbarkeit, f

    FR

    • courant admissible, m
    • courant permanent admissible, m

    Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток

  • 2 травы

    1. Gras

     

    травы

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    grass
    A very large and widespread family of Monocotyledoneae, with more than 10.000 species, most of which are herbaceous, but a few are woody. The stems are jointed, the long, narrow leaves originating at the nodes. The flowers are inconspicuous, with a much reduced perianth, and are wind-pollinated or cleistogamous. The fruit in single-seeded, usually a caryopsis. Grasses are the most important of all plants for food. (Source: ALL)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > травы

  • 3 распределительный щит

    1. Verteiler, m
    2. Schalttafel
    3. elektrischer Verteiler, m

     

    распределительный щит
    Комплектное устройство, содержащее различную коммутационную аппаратуру, соединенное с одной или более отходящими электрическими цепями, питающееся от одной или более входящих цепей, вместе с зажимами для присоединения нейтральных и защитных проводников.
    [ ГОСТ Р МЭК 60050-826-2009]

    щит распределительный
    Электротехническое устройство, объединяющее коммутационную, регулирующую и защитную аппаратуру, а также контрольно-измерительные и сигнальные приборы
    [Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]

    распределительный щит

    [А.С.Гольдберг. Англо-русский энергетический словарь. 2006 г.]

    EN

    distribution board
    assembly containing different types of switchgear and controlgear associated with one or more outgoing electric circuits fed from one or more incoming electric circuits, together with terminals for the neutral and protective conductors.
    [IEV number 826-16-08]

    FR

    tableau de répartition, m
    ensemble comportant différents types d'appareillage associés à un ou plusieurs circuits électriques de départ alimentés par un ou plusieurs circuits électriques d'arrivée, ainsi que des bornes pour les conducteurs neutre et de protection.
    [IEV number 826-16-08]

    Параллельные тексты EN-RU

    Distribution switchboards, including the Main LV Switchboard (MLVS), are critical to the dependability of an electrical installation. They must comply with well-defined standards governing the design and construction of LV switchgear assemblies

    A distribution switchboard is the point at which an incoming-power supply divides into separate circuits, each of which is controlled and protected by the fuses or switchgear of the switchboard. A distribution switchboard is divided into a number of functional units, each comprising all the electrical and mechanical elements that contribute to the fulfilment of a given function. It represents a key link in the dependability chain.

    Consequently, the type of distribution switchboard must be perfectly adapted to its application. Its design and construction must comply with applicable standards and working practises.

    [Schneider Electric]

    Распределительные щиты, включая главный распределительный щит низкого напряжения (ГРЩ), играют решающую роль в обеспечении надежности электроустановки. Они должны отвечать требованиям соответствующих стандартов, определяющих конструкцию и порядок изготовления НКУ распределения электроэнергии.

    В распределительном щите выполняется прием электроэнергии и ее распределение по отдельным цепям, каждая из которых контролируется и защищается плавкими предохранителями или автоматическими выключателями.
    Распределительный щит состоит из функциональных блоков, включающих в себя все электрические и механические элементы, необходимые для выполнения требуемой функции. Распределительный щит представляет собой ключевое звено в цепи обеспечения надежности.

    Тип распределительного щита должен соответствовать области применения. Конструкция и изготовление распределительного щита должны удовлетворять требованиям применимых стандартов и учитывать накопленную практику применения.

    [Перевод Интент]

     

    5654

    Рис. Schneider Electric

    With Prisma Plus G you can be sure to build 100% Schneider Electric switchboards that are safe, optimised:

    > All components (switchgear, distribution blocks, prefabricated connections, etc.) are perfectly rated and coordinated to work together;

    > All switchboard configurations, even the most demanding ones, have been tested.

    You can prove that your switchboard meets the current standards, at any time.

    You can be sure to build a reliable electrical installation and give your customers full satisfaction in terms of dependability and safety for people and the installation.

    Prisma Plus G with its discreet design, blends harmoniously into all tertiary and industrial buildings, including in entrance halls and passageways.

    With Prisma Plus G you can build just the right switchboard for your customer, sized precisely to fit costs and needs.

    With this complete, prefabricated and tested system, it's easy to upgrade your installation and still maintain the performance levels.

    > The wall-mounted and floor-standing enclosures combine easily with switchboards already in service.

    > Devices can be replaced or added at any time.

    [Schneider Electric]

    С помощью оболочек Prisma Plus G можно создавать безопасные распределительные щиты, на 100 % состоящие из изделий Schneider Electric:

    > все изделия (коммутационная аппаратура, распределительные блоки, готовые заводские соединения и т. д.) полностью совместимы механически и электрически;

    > все варианты компоновки распределительных щитов, в том числе для наиболее ответственных применений, прошли испытания.

    В любое время вы можете доказать, что ваши распределительные щиты полностью соответствуют требованиям действующих стандартов.

    Вы можете быть полностью уверены в том, что создаете надежные электроустановки, удовлетворяющие всем требованиям безопасности для людей и оборудования

    Благодаря строгому дизайну, распределительные щиты Prisma Plus G гармонично сочетаются с интерьером любого общественного или промышленного здания. Они хорошо смотрятся и в вестибюле, и в коридоре.

    Применяя оболочки Prisma Plus G можно создавать распределительные щиты, точно соответствующие требованиям заказчика как с точки зрения технических характеристик, так и стоимости.

    С помощью данной испытанной системы, содержащей все необходимые компоненты заводского изготовления можно легко модернизировать существующую электроустановку и поддерживать её уровни производительности.

    > Навесные и напольные оболочки можно легко присоединить к уже эксплуатируемым распределительным щитам.

    > Аппаратуру можно заменять или добавлять в любое время.

    [Перевод Интент]

     

    The switchboard, central to the electrical installation.

    Both the point of arrival of energy and a device for distribution to the site applications, the LV switchboard is the intelligence of the system, central to the electrical installation.

    [Schneider Electric]

    Распределительный щит – «сердце» электроустановки.

    Низковольтное комплектное устройство распределения является «сердцем» электроустановки, поскольку именно оно принимает электроэнергию из сети и распределяет её по территориально распределенным нагрузкам.

    [Перевод Интент]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > распределительный щит

  • 4 НКУ распределения и управления

    1. Schaltanlagen und/oder Schaltgeräte

     

    низковольтное устройство распределения и управления (НКУ)
    Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
    [ ГОСТ Р МЭК 61439-1-2012]

    низковольтное устройство распределения и управления

    Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
    Примечания
    1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
    2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
    3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
    [ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]

    EN

    power switchgear and controlgear assembly (PSC-assembly)
    low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
    [IEC 61439-2, ed. 1.0 (2009-01)]

    low-voltage switchgear and controlgear assembly
    combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
    [IEC 61892-3, ed. 2.0 (2007-11)]

    switchgear and controlgear
    a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
    [IEV number 441-11-01]

    switchgear and controlgear

    electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
    NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
    [IEV number 826-16-03 ]

    switchboard
    A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
    [ McGraw-Hill Dictionary of Architecture & Construction]

    switchboard
    One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
    [ The American Heritage Dictionary of the English Language]

    FR

    ensemble d'appareillage de puissance (ensemble PSC)
    ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
    [IEC 61439-2, ed. 1.0 (2009-01)]

    appareillage, m
    matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
    NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
    [IEV number 826-16-03 ]

    appareillage
    terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
    [IEV number 441-11-01]


    A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
    Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
    The types of switchboards, classified by basic features of construction, are as follows:
    1. Live-front vertical panels
    2. Dead-front boards
    3. Safety enclosed boards( metal-clad)


    [American electricians’ handbook]

    Параллельные тексты EN-RU

    The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.

    Its definition, design and installation are based on precise rules; there is no place for improvisation.

    The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.

    It specifies in particular:

    > the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;

    > the design and verification rules, constituting a benchmark for product certification.

    All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.


    Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.

    A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.

    Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.

    What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.

    [Schneider Electric]

    НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.

    Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.

    Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).

    В частности, он определяет:

    > распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;

    > конструкцию, технические характеристики, виды и методы испытаний НКУ.

    В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.

    Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.

    Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.

    Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.

    Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.

    [Перевод Интент]

     

    LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.

    The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.

    In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.

    Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.

    The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.

    [ABB]

    Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.

    Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам

    Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.

    Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются

    Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.

    [Перевод Интент]

    Тематики

    • НКУ (шкафы, пульты,...)

    Классификация

    >>>

    Действия

    Синонимы

    Сопутствующие термины

    EN

    DE

    • Schaltanlagen und/oder Schaltgeräte

    FR

    Русско-немецкий словарь нормативно-технической терминологии > НКУ распределения и управления

  • 5 НКУ защищенное

    1. geschlossene (gekapselte) Schaltgerätekombination

     

    НКУ защищенное
    НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X.
    [ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]

    защищенное НКУ
    НКУ, конструкция которого обеспечивает требуемую степень защиты со всех сторон от прикосновения к частям, находящимся под напряжением (за исключением монтажной поверхности).
    [ ГОСТ Р МЭК 61439.1-2013]

    EN

    enclosed assembly (of switchgear and controlgear)
    an assembly enclosed on all sides, top and bottom in such a manner as to provide a specified degree of protection
    NOTE – The mounting surface may form a part of the enclosure when specified in the relevant publication.
    [IEV number 441-12-02]

    FR

    ensemble (d'appareillage de connexion et de commande)
    sous enveloppe
    ensemble comportant une paroi sur toutes ses faces latérales, supérieure et inférieure, de façon à assurer un degré de protection spécifié
    NOTE – La surface de montage peut faire partie de l'enveloppe lorsqu'une publication particulière le spécifie.
    [IEV number 441-12-0

    0078
    Шкаф - защищенное НКУ, предназначенное для установки на полу


    Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
    Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
    Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.


    Safety enclosed switchgear may be classified with respect to purpose of application as follows:
    1. General medium- or high-voltage switchgear
    2. Primary unit substations
    3. Rectifier unit substations
    4. Secondary unit substations or power centers
    5. General low-voltage switchgear
    6. Low-voltage distribution switchboards
    7. Motor-control-center switchboards

    [American electricians’ handbook]

    Тематики

    • НКУ (шкафы, пульты,...)

    Классификация

    >>>

    Обобщающие термины

    Синонимы

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > НКУ защищенное

  • 6 пролив Ваддензе

    1. Wattenmeer

     

    пролив Ваддензе

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    Wadden Sea
    The Wadden sea is a shallow sea extending along the North Sea coasts of The Netherlands, Germany and Denmark. It is a highly dynamic ecosystem with tidal channels, sands, mud flats, salt marshes, beaches, dunes, river mouths and a transition zone to the North Sea, the offshore zone. Most parts of the Wadden Sea, in particular in The Netherlands and Lower Saxony, are sheltered by barrier islands and contain smaller or wider areas of intertidal flats. The present form of the Wadden Sea is the result of both natural forces and action by man. Twice a day, on average, 15 km3 of sea water enter the Wadden sea. With the water from the North Sea, large amount of sand and silt are imported which settle in places with little water movement. During low tides large parts of the Wadden Sea emerge. These so-called tidal flats cover about 2/3 of the tidal area and are one of its most characteristic features. Nowhere in the world can such a large unbroken stretch of tidal flats be found. They account for 60% of all tidal areas in Europe and North Africa. (Source: CWSS)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > пролив Ваддензе

  • 7 формирование почвы

    1. Bodenbildung

     

    формирование почвы

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    soil formation
    The combination of natural processes by which soils are formed. It is also known as pedogenesis. The most important soil-forming factors are parent material, terrain, climate, aspect, vegetation cover, microorganisms in the soil and the age of the land surface. Some pedologists would add to this list the influence of human activities. All the factors exhibit varying degrees of interrelationship and some are more important than others, with climate often being singled out as the most important. (Source: WHIT)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > формирование почвы

  • 8 ДДТ

    1. DDT

     

    ДДТ

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    DDT
    A persistent organochlorine insecticide, also known as dichlorodiphenyltrichloroethane, that was introduced in the 1940s and used widely because of its persistence (meaning repeated applications were unnecessary), its low toxicity to mammals and its simplicity and cheapness of manufacture. It became dispersed all over the world and, with other organochlorines, had a disruptive effect on species high in food chains, especially on the breeding success of certain predatory birds. DDT is very stable, relatively insoluble in water, but highly soluble in fats. Health effects on humans are not clear, but it is less toxic than related compounds. It is poisonous to other vertebrates, especially fish, and is stored in the fatty tissue of animals as sublethal amounts of the less toxic DDE. Because of its effects on wildlife its use in most countries is now forbidden or strictly limited. (Source: MGH / ALL)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > ДДТ

  • 9 небаланс напряжений

    1. Spannungsunsymmetrie

     

    небаланс напряжений
    Отличие по модулю значения хотя бы одного из фазных или линейных напряжений многофазной системы электроснабжения от значений напряжений других фаз.
    [ ГОСТ 23875-88]

    EN

    voltage unbalance
    phenomenon due to the differences between voltage deviations on the various phases, at a point of a polyphase system, resulting from differences between the phase currents or geometrical asymmetry in the line
    [IEV number 604-01-29]

    voltage unbalance (imbalance)
    in a polyphase system, a condition in which the magnitudes of the phase voltages or the phase angles between consecutive phases are not all equal (fundamental component)
    NOTE In three phase systems, the degree of inequality is usually expressed as the ratio of the negative and zero sequence components to the positive sequence component. In this technical report, voltage unbalance is considered in relation to three-phase systems and negative sequence only
    [IEC 61000-3-13, ed. 1.0 (2008-02)]

    voltage unbalance
    condition in a polyphase system in which the r.m.s. values of the line voltages (fundamental component), and/or the phase angles between consecutive line voltages, are not all equal
    NOTE 1 The degree of the inequality is usually expressed as the ratios of the negative- and zero-sequence components to the positive-sequence component.
    NOTE 2 In this standard, voltage unbalance is considered in relation to 3-phase systems.
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    déséquilibre des tensions d'un réseau
    phénomène résultant des différences de charge ou des dissymétries géométriques de lignes et qui provoque des différences entre les écarts de tension sur les diverses phases en un point d'un réseau polyphasé
    [IEV number 604-01-29]

    déséquilibre de tension
    dans un réseau d’énergie électrique polyphasé, état dans lequel les valeurs efficaces des tensions entre conducteurs (composante fondamentale), et/ou les différences de phase entre conducteurs successifs, ne sont pas toutes égales
    NOTE 1 Le taux de déséquilibre s’exprime habituellement par le rapport de la composante inverse ou homopolaire à la composante directe.
    NOTE 2 Dans la présente norme, le déséquilibre de tension est relatif aux réseaux triphasés
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Параллельные тексты EN-RU

    4748       4749      4750

    Voltage unbalance
    Voltage unbalance on the most unbalanced phase, displayed as a percentage of Vavg.

    [Schneider Electric]

    Небаланс напряжений
    Самое значительное отличие по модулю значения одного из линейных напряжений, выраженное в процентах от среднего напряжения Vavg.

    [Перевод Интент]


    Недопустимые, нерекомендуемые

    Тематики

    EN

    DE

    FR

    Смотри также

    Русско-немецкий словарь нормативно-технической терминологии > небаланс напряжений

  • 10 хвойные

    1. Nadelbaum

     

    хвойные

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    conifer
    An order of conebearing plants which includes nearly all the present day Gymnospermae. Most are tall evergreen trees with needle-like (e.g., pines), linear (e.g. firs) or scale-like (e.g., cedars) leaves. They are characteristic of temperate zones and the main forest trees of colder regions. They provide timber, resins, tars, turpentine and pulp for paper. (Source: ALL)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > хвойные

  • 11 граница между воздухом и поверхностью океана

    1. Ozean-Luft Schnitstelle

     

    граница между воздухом и поверхностью океана

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    ocean-air interface
    The sea and the atmosphere are fluids in contact with one another, but in different energy states - the liquid and the gaseous. The free surface boundary between them inhibits, but by no means totally prevents, exchange of mass and energy between the two. Almost all interchanges across this boundary occur most effectively when turbulent conditions prevail. A roughened sea surface, large differences in properties between the water and the air, or an unstable air column that facilitates the transport of air volumes from sea surface to high in the atmosphere. Both heat and water (vapor) tend to migrate across the boundary in the direction from sea to air. Heat is exchanged by three processes: radiation, conduction, and evaporation. The largest net exchange is through evaporation, the process of transferring water from sea to air by vaporization of the water. (Source: PARCOR)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > граница между воздухом и поверхностью океана

  • 12 деградация природных ресурсов

    1. Abbau von natürlichen Ressourcen

     

    деградация природных ресурсов

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    degradation of natural resources
    The result of the cumulative activities of farmers, households, and industries, all trying to improve their socio-economic well being. These activities tend to be counterproductive for several reasons. People may not completely understand the long-term consequences of their activities on the natural resource base. The most important ways in which human activity is interfering with the global ecosystem are: a) fossil fuel burning which may double the atmospheric carbon dioxide concentration by the middle of the next century, as well as further increasing the emissions of sulphur and nitrogen very significantly; b) expanding agriculture and forestry and the associated use of fertilizers (nitrogen and phosphorous) are significantly altering the natural circulation of these nutrients; c) increased exploitation of the freshwater system both for irrigation in agriculture and industry and for waste disposal. (Source: WPR)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > деградация природных ресурсов

  • 13 заброшенная мусорная яма

    1. Altablagerung

     

    заброшенная мусорная яма

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    old landfill site
    Landfill that has been filled and covered with topsoil and seeded. The most common end use for landfills is open spaces with no active recreation taking place over the completed landfill. The obvious reason for this use is that the completed surface is steeply sloped to provide rapid runoff. Also, no irrigation of the cover grasses should be allowed. It is very unlikely to think that commercial or industrial buildings will be constructed on a completed landfill. If the end use is such that the public will be walking on the site, it is important that all manholes be properly secured, leachate lagoons fenced, and other potential hazards eliminated. (Source: CORBITa)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > заброшенная мусорная яма

  • 14 масляный трансформатор

    1. Öltransformator

     

     

    масляный трансформатор
    Трансформатор с жидким диэлектриком, в котором основной изолирующей средой и теплоносителем служит трансформаторное масло
    [ ГОСТ 16110-82]


    масляный трансформатор
    Трансформатор, магнитная система и обмотки которого погружены в масло
    (МЭС 421-01-14)
    [ ГОСТ 30830-2002]

    EN

    oil-immersed type transformer
    a transformer of which the magnetic circuit and windings are immersed in oi
    [IEV number 421-01-14]

    FR

    transformateur immergé dans l'huile
    transformateur dont le circuit magnétique et les enroulements sont immergés dans l'huile
    [IEV number 421-01-14]

    Oil transformers
    The magnetic circuit and the windings are immersed in a liquid dielectric that provides insulation and evacuates the heat losses of the transformer.
    This liquid expands according to the load and the ambient temperature. PCBs and TCBs are now prohibited and mineral oil is generally used. It is flammable and requires protective measures against the risks of fire, explosion and pollution.

    The most commonly used protective measures are the DGPT or the DGPT2: Gas, Pressure and Temperature sensor with 1 or 2 sensing levels on the temperature. This system cuts off the LV load (1st level) then the HV supply (2nd level) when there is a fault inside the transformer. A holding tank is used to recover all the liquid dielectric.

    Of the four types of immersed transformer: free breathing transformers, gas cushion transformers, transformers with expansion tank and transformers with integral filling, only the latter are currently installed.

    [Legrand]

    Масляные трансформаторы
    Магнитная система и обмотки трансформатора погружены в жидкий диэлектрик, служащий изоляцией и теплоносителем.
    Жидкий диэлектрик изменяет свой объем в соответствии с нагрузкой трансформатора и температурой окружающей среды. Поскольку в настоящее время применение полихлорированных дифенилов и тетрахлорбифенилов запрещено, то в основном используют минеральное масло. Оно огнеопасно, поэтому необходимо принимать меры против возникновения пожара, взрыва и загрязнения окружающей среды.

    Как правило, применяются системы DGPT (одноуровневые системы, использующие датчики газа, давления и температуры) или DGPT2 – двухуровневые системы.
    В случае возникновения аномального состояния трансформатора данные системы отключают нагрузку цепей низшего напряжения (первый уровень защиты), а затем питание обмотки высшего напряжения (второй уровень защиты). Активная часть трансформатора находится в баке и полностью покрыта жидким диэлектриком.

    Существует четыре типа масляных трансформаторов: трансформаторы с системой свободного дыхания, трансформаторы с газовой подушкой между зеркалом масла и крышкой трансформатора, трансформаторы с расширительным баком и трансформаторы с гофрированным баком. В настоящее время применяют только трансформаторы последнего типа

    [Интент]

    0375
    [http://www.ramo-chelny.ru/konschasti.html]

    Масляный трансформатор:

    1. Шихтованный магнитопровод
    2. Обмотка низшего напряжения
    3. Обмотка высшего напряжения
    4. Трубчатый бак
    5. Термометр
    6. Переключатель регулировочных отводов обмотки высшего напряжения
    7. Ввод (проходной изолятор) обмотки низшего напряжения
    8. Ввод (проходной изолятор) обмотки высшего напряжения
    9. Расширительный бак

    0376
    [http://transfcomplect.narod.ru/transformator.html]

    Тематики

    Классификация

    >>>

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > масляный трансформатор

  • 15 плавкий предохранитель

    1. Sicherung

     

    плавкий предохранитель
    Коммутационный аппарат, который посредством плавления одного или нескольких своих специально спроектированных и калиброванных элементов размыкает цепь, в которую он включен, и отключает ток, когда он превышает заданную величину в течение достаточного времени. Плавкий предохранитель содержит все части, образующие укомплектованный аппарат.
    МЭК 60050(441-18-01).
    [ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]

    плавкий предохранитель
    Аппарат, который вследствие расплавления одного или нескольких специально спроектированных и рассчитанных элементов размыкает цепь, в которую он включен, отключая ток, превышающий заданное значение в течение достаточно продолжительного времени. В состав плавкого предохранителя входят все части, образующие аппарат в комплекте
    [ ГОСТ Р 50339. 0-2003 ( МЭК 60269-1-98)]

    предохранитель
    Коммутационный электрический аппарат, предназначенный для отключения защищаемой цепи посредством разрушения специально предусмотренных для этого токоведущих частей под действием тока, превышающего определенную величину.
    [ ГОСТ 17703-72]

    предохранитель
    Устройство для разрыва электрических цепей при силе тока, превышающей допустимое значение
    [Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]

    EN

    fuse
    a device that by the fusing of one or more of its specially designed and proportioned components, opens the circuit in which it is inserted by breaking the current when this exceeds a given value for a sufficient time. The fuse comprises all the parts that form the complete device
    [IEV number 441-18-01 ]

    FR

    fusible
    coupe-circuit à fusibles

    appareil dont la fonction est d'ouvrir par la fusion d'un ou de plusieurs de ses éléments conçus et calibrés à cet effet le circuit dans lequel il est inséré en coupant le courant lorsque celui-ci dépasse pendant un temps suffisant une valeur donnée. Le fusible comprend toutes les parties qui constituent l'appareil complet
    [IEV number 441-18-01 ]

    Настоящий стандарт распространяется на плавкие предохранители на номинальный ток от 2 до 2500 А, номинальное напряжение переменного тока до 1000 В и постоянного тока до 1200 В, устанавливаемые в комплектные устройства и предназначенные для защиты при перегрузках и коротких замыканиях силовых и вспомогательных цепей электроустановок промышленных предприятий, общественных и жилых зданий, изготовляемые для нужд народного хозяйства и экспорта и номинальное напряжение до 3000 В для защиты полупроводниковых устройств.

    3.2.14. Предохранители должны быть сконструированы таким образом, чтобы отключать электрическую цепь при токах отключения в пределах: от условного тока плавления — для предохранителей с плавкими вставками типов g и gR или от наименьшего тока отключения, установленного в стандартах или технических условиях на предохранители конкретных серий и типов, для предохранителей с плавкими вставками типов а и aR — до наибольшего тока отключения
    [ ГОСТ 17242-86]

    ... токи, при которых проводят испытания, предназначенные для проверки способности данного плавкого предохранителя срабатывать удовлетворительно в диапазоне малых сверхтоков.
    [ ГОСТ Р 50339.0-2003]

    ... Если неисправность заканчивается срабатыванием плавкого предохранителя или если плавкий предохранитель не срабатывает примерно в течение 1 с, то...
    [ ГОСТ Р 52319-2005]

    ЭЛЕКТРИЧЕСКИЕ ПАРАМЕТРЫ И ХАРАКТЕНИСТИКИ ПРЕДОХРАНИТЕЛЕЙ
    (взято из ГОСТ 17242-86)

    • Для держателя (или основания) предохранителя:
      • номинальное напряжение;
      • номинальный ток;
      • род тока и номинальная частота для переменного тока;
      • допустимые потери мощности;
      • число полюсов, если их более одного.
    • Для плавкой вставки:
      • номинальное напряжение;
      • номинальный ток;
      • род тока и номинальная частота для переменного тока;
      • потери мощности;
      • время-токовые характеристики с указанием коэффициентов K1 и K2 для плавких вставок типа а;
      • перегрузочная способность;
      • диапазон токов отключения;
      • наибольшая отключающая способность;
      • наименьший ток отключения для плавких вставок типа а;
      • характеристика пропускаемого тока;
      • характеристики интегралов Джоуля;
      • перенапряжение и характеристика перенапряжения для плавких вставок типов aR и gR;
      • условия селективности (при необходимости);
      • электрическое сопротивление плавкой вставки в холодном состоянии (допускается указать в рабочих чертежах, утвержденных в установленном порядке).
    • Для предохранителя:
      • степень защиты по ГОСТ 14255—69;
      • номинальное напряжение, номинальный ток и коммутационная способность свободных контактов (при их наличии).

    Параллельные тексты EN-RU

    Check to make sure that fuse F1 on power supply module V is not fused.

    If the fuse is defective, it should not be replaced without determining the cause of failure.

    If a fuse is replaced without eliminating the problem, there is the danger that the damage will spread.

    [Schneider Electric]

    Убедитесь в исправности предохранителя F1 в модуле питания V.

    Если предохранитель оказался неисправным, то прежде чем заменить его необходимо установить причину возникновения неисправности.

    Замена предохранителя без выяснения причины его срабатывания может привести к повторению срабатывания.


    [Перевод Интент]

    High voltage system may embrace a fuse.
    Note that a fuse may not be manually adjusted as the circuit breaker relay does so the fuse choice for the appropriate purpose/circuit adaptation is deemed most important.

    [LS Industrial Systems]

    Высоковольтная система < электропитания> может содержать предохранители.
    Обратите внимание! Предохранитель нельзя настроить, как это можно сделать с расцепителем автоматического выключателя. Поэтому предохранитель необходимо выбрать так, чтобы он как можно точнее соотвествовал конкретным условиям защиты аппарата или участка цепи.

    [Перевод Интент]


     

    Тематики

    Классификация

    >>>

    Обобщающие термины

    Действия

    Синонимы

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > плавкий предохранитель

  • 16 тропический дождевой лес

    1. tropischer Regenwald

     

    тропический дождевой лес

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    tropical rain forest
    The most valuable and the richest ecosystem on Earth. It plays a critical part in the Earth's life support systems and house 50%, and possibly as much as 90%, of all the species on Earth. It is a key storehouse of foods, oils and minerals, and a source of ingredients that make up a range of medical treatments. It also represents home and livelihood for many people. However, more than half of the rainforests have disappeared, chopped down for valuable tropical hardwoods, or cleared to provide areas for cattle grazing or human habitation. The forests play an important part in climate patterns, and deforestation is thought to be responsible for 18% of global warming. Furthermore, as they disappear there is also an albedo effect - a damaging increase in the sunlight reflected - which affects wind and rainfall patterns. (Source: WRIGHT)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > тропический дождевой лес

  • 17 уровень стояния грунтовых вод

    1. freies Grundwasser

     

    уровень стояния грунтовых вод

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    water table
    Water that occupies pores, cavities, cracks and other spaces in the crustal rocks. It includes water precipitated from the atmosphere which has percolated through the soil, water that has risen from deep magmatic sources liberated during igneous activity and fossil water retained in sedimentary rocks since their formation. The presence of groundwater is necessary for virtually all weathering processes to operate. Phreatic water is synonymous with groundwater and is the most important source of any water supply. (Source: WHIT)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > уровень стояния грунтовых вод

  • 18 экологический аспект населенных пунктов

    1. Umweltaspekt von Siedlungen

     

    экологический аспект населенных пунктов

    [ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    EN

    environmental aspect of human settlements
    Human settlements have an adverse impact on many ecosystems and on themselves by the addition of toxic or harmful substances to the outer lithosphere, hydrosphere, and atmosphere. The major types of environmental pollutants are sewage, trace metals, petroleum hydrocarbons, synthetic organic compounds, and gaseous emissions. Most, if not all, of the additions of potentially harmful substances to the environment are result of the population growth and the technological advances of industrial societies. (Source: PARCORa)
    [http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]

    Тематики

    EN

    DE

    FR

    Русско-немецкий словарь нормативно-технической терминологии > экологический аспект населенных пунктов

См. также в других словарях:

  • Most of All — Single by Jody Watley from the album Jody Watley Released 1988 …   Wikipedia

  • most of all — first/best/most/etc of all phrase used for emphasizing that you mean before anything else better than anything else more than anything else etc First of all, I want to welcome our guest speaker. His music was the thing he loved most of all.… …   Useful english dictionary

  • Most of All - The Best of Deborah Harry — Infobox Album | Name = Most Of All The Best Of Deborah Harry Type = Compilation album Artist = Deborah Harry Released = November 8 1999 Recorded = 1981 1993, 1999 Genre = Pop Length = 75:49 Label = flag|UK Chrysalis Records/EMI Producer = Various …   Wikipedia

  • most of all — mostly, mainly; the most, more than anything else …   English contemporary dictionary

  • most of all — Especially, principally, chiefly, above all …   New dictionary of synonyms

  • most of all — adverb to a greater extent than anything else …   Wiktionary

  • most — [ moust ] function word, quantifier *** Most is the superlative form of much and many and can be used in the following ways: as an adverb (before an adjective or another adverb): a most interesting lecture the question that is asked most often.… …   Usage of the words and phrases in modern English

  • All the Most — 2011 All The Most  российская Брейкинг команда, созданная в 2001 году. Изначальное название Almost (пер. с англ.: Почти), так как в состав команды входило лишь два человека: Yan The Shr …   Википедия

  • Most (disambiguation) — Most is a city in the Czech Republic. Most may also refer to: Contents 1 People 2 Places 2.1 Bridges …   Wikipedia

  • all — [ ɔl ] function word, quantifier *** All can be used in the following ways: as a determiner (followed by an uncountable or plural noun): They had given up all hope. All children deserve encouragement. as a predeterminer (followed by a word such… …   Usage of the words and phrases in modern English

  • All-Clad — Metalcrafters are manufacturers of premium cookware.All Clad was established in 1968 after founder John Ulam discovered a unique process that uses heat and pressure to bond different metals into “sandwiched” sheets. This patented “roll bonding”… …   Wikipedia

Поделиться ссылкой на выделенное

Прямая ссылка:
Нажмите правой клавишей мыши и выберите «Копировать ссылку»