-
1 расстояние утечки
расстояние утечки
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание. Стык между двумя элементами из изоляционного материала считают частью поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
расстояние утечки (см. приложение В)
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание — При определении расстояния утечки относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9
[ ГОСТ Р 50345-99( МЭК 60898-95)]
расстояние утечки по поверхности
-
[IEV number 151-15-50]
путь утечки
Кратчайшее расстояние вдоль поверхности изоляции между двумя проводящими частями или между проводящей частью и доступной поверхностью.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - A joint between two pieces of insulating material is considered part of the surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - For the purpose of determining a creepage distance to accessible parts, the accessible surface of an insulating enclosure is considered conductive as if it was covered by a metal foil wherever it can be touched by a hand or a standard test finger according to figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
creepage distance
shortest distance along the surface of insulation between two conductive parts or between a conductive part and the accessible surface
[IEC 60335-1, ed. 4.0 (2001-05)]
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts
[IEV number 151-15-50]FR
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Un joint entre deux portions de matière isolante est considéré comme faisant partie de la surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Pour la détermination d'une ligne de fuite pour des parties accessibles, la surface accessible d'une enveloppe isolante est considérée comme conductrice comme si elle était recouverte d'une feuille métallique à tout endroit où elle peut être touchée par la main ou par le doigt d'essai normalisé conforme à la figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
ligne de fuite
plus petite distance le long de la surface de l’isolation entre deux parties conductrices ou entre une partie conductrice et la surface accessible
[IEC 60335-1, ed. 4.0 (2001-05)]
ligne de fuite, f
distance la plus courte, le long de la surface d'un isolant solide, entre deux parties conductrices
[IEV number 151-15-50]1) Должно быть проводящими
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > расстояние утечки
-
2 заземляющий электрод подземных кабельных трасс
заземляющий электрод подземных кабельных трасс
Заземляющий электрод, обычно проложенный вдоль кабельной трассы в целях заземления этой трассы.
[ ГОСТ Р МЭК 60050-195-2005]EN
underground cable-route earth electrode
earth electrode usually laid along the cable route to provide earthing along its route
Source: 461-06-20 MOD
[IEV number 195-02-28]FR
prise de terre enterrée associée à un câble
prise de terre habituellement posée le long du parcours d'un câble, destinée à assurer la mise à la terre le long du parcours de ce câble
Source: 461-06-20 MOD
[IEV number 195-02-28]Тематики
EN
- underground cable-route earth electrode
- underground cable-route ground electrode (US)
- uninsulated earth conductor (deprecated)
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > заземляющий электрод подземных кабельных трасс
-
3 авария на дороге
авария на дороге
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
traffic accident
An unexpected incident with potential for harm occurring through the movement or collision of vessels, vehicles or persons along a land, water, air or space route. (Source: OED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > авария на дороге
-
4 автобусная остановка
автобусная остановка
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
bus station
A place along a route or line at which a bus stops for fuel or to pick up or let off passengers or goods, especially with ancillary buildings and services. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > автобусная остановка
-
5 воздушный зазор
воздушный зазор
Кратчайшее расстояние между двумя токоведущими и/или токоведущей и открытой проводящей частью.
МЭК 60050(441-17-31).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
воздушный зазор
Кратчайшее расстояние в воздухе между двумя токопроводящими1) частями вдоль линии наименьшей протяженности между этими токоведущими1) частями.
Примечание. Для определения воздушного зазора относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9.
(МЭС 441-17-31)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
1) Должно быть проводящими
[Интент]
изоляционный промежуток
Расстояние между двумя токопроводящими частями вдоль нити, натянутой по кратчайшему пути между ними.
[ ГОСТ Р 52726-2007]
зазор
Кратчайшее расстояние по воздуху между двумя токопроводящими1) частями оборудования.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
1) Должно быть проводящими
[Интент]EN
clearance
the distance between two conductive parts along a string stretched the shortest way between these conductive parts
[IEV number 441-17-31]
clearance
shortest distance in air between two conductive parts
NOTE – This distance applies only to parts that are exposed to the atmosphere and not to parts which are insulated parts or covered with casting compound.
[IEV number 426-04-12]FR
distance d'isolement
distance entre deux parties conductrices le long d'un fil tendu suivant le plus court trajet possible entre ces deux parties conductrices
[IEV number 441-17-31]
distance d’isolement dans l’air
plus courte distance dans l’air entre deux pièces conductrices
NOTE – Cette distance s'applique seulement aux parties exposées à l'atmosphère et non aux parties isolées ou recouvertes par un composé de moulage.
[IEV number 426-04-12]
Параллельные тексты EN-RU
Clearance distance
Shortest distance in air between two conductive parts or between a conductive part and the accessible surface of the relay.
[Tyco Electronics]Воздушный зазор
Кратчайшее расстояние по воздуху между двумя проводящими частями или между проводящей частью и доступной для прикосновения поверхностью реле.
[Перевод Интент]
Наименьшее изоляционное расстояние по воздуху (в свету) от токоведущих до заземленных частей опоры
[ПУЭ]
2
воздушный зазор
-
[IEV number 151-14-05]EN
air gap
short gap in the magnetic material forming a magnetic circuit
Source: 221-04-13 MOD
[IEV number 151-14-05]FR
entrefer, m
coupure de faible longueur dans le matériau magnétique constituant un circuit magnétique
Source: 221-04-13 MOD
[IEV number 151-14-05]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- air clearance
- air distance
- air gap (2)
- air-gap clearance
- clearance
- contact gap (1)
- contact opening distance (1)
- contact separation (1)
- flashover distance
- insulation clearanse
- insulation distance
- isolating distance
DE
FR
- distance d'isolement
- distance d’isolement dans l’air
- entrefer, m (2)
Русско-немецкий словарь нормативно-технической терминологии > воздушный зазор
-
6 выравнивание потенциалов
выравнивание потенциалов
Метод снижения напряжения прикосновения и шага между точками электрической цепи, к которым возможно одновременное прикосновение или на которых может одновременно стоять человек
[ ГОСТ 12.1.009-76]
выравнивание потенциала
-
[IEV number 151-15-51]EN
potential grading
reduction of substantial inequalities of electric field strength in or along an insulator or insulation by constructional measures
[IEV number 151-15-51]FR
répartition des potentiels, f
réduction des inégalités importantes du champ électrique à l'intérieur ou à la surface d'un isolateur ou d'une isolation par des moyens incorporés au dispositif
[IEV number 151-15-51]Тематики
EN
DE
FR
- répartition des potentiels, f
Русско-немецкий словарь нормативно-технической терминологии > выравнивание потенциалов
-
7 гигроскопичная лента
- Quellband, n
гигроскопичная лента
водонабухающая лента
лента, применяемая под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-16]EN
water blocking tape
swelling tape
tape applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-16]FR
ruban d'étanchéité
ruban gonflant
ruban appliqué sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-16]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellband, n
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичная лента
-
8 гигроскопичная пудра
- Quellpulver, n
гигроскопичная пудра
водонабухающая пудра
порошковый наполнитель, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-14]EN
water blocking powder
swelling powder
powder applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-14]FR
poudre d'étanchéité
poudre gonflante
poudre appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-14]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellpulver, n
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичная пудра
-
9 гигроскопичный клей
- Quellmasse, f
гигроскопичный клей
водонабухающий клей
клей, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-17]EN
water blocking glue
swelling glue
glue applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-17]FR
matière d'étanchéité
matière appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-17]
Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellmasse, f
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичный клей
-
10 двухкоординатный самописец
двухкоординатный самописец
-
[IEV number 313-02-04]EN
X-Y recorder
recording instrument in which the marking device is moved along two orthogonal axes by two separate devices, to each of which a quantity to be recorded is applied
[IEV number 313-02-04]FR
enregistreur X-Y
appareil enregistreur dans lequel le dispositif d'inscription est déplacé le long de deux axes orthogonaux par deux dispositifs distincts à chacun desquels est appliquée une grandeur à enregistrer
[IEV number 313-02-04]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > двухкоординатный самописец
-
11 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
12 дорожная безопасность
дорожная безопасность
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
road safety
Any measure, technique or design intended to reduce the risk of harm posed by moving vehicles along a constructed land route. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > дорожная безопасность
-
13 железнодорожная станция
железнодорожная станция
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
railway station
A place along a route or line at which a train stops to pick up or let off passengers or goods, especially with ancillary buildings and services. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > железнодорожная станция
-
14 жилой район с дорогами, оборудованными устройствами по контролю за скоростью
жилой район с дорогами, оборудованными устройствами по контролю за скоростью
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
residential area with traffic calmings
Residential zones where raised areas are built across roads so that vehicles are forced to move more slowly along it. (Source: CAMB)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > жилой район с дорогами, оборудованными устройствами по контролю за скоростью
-
15 защита берегов
защита берегов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
bank protection
Engineering work which aims at the protection of banks of a river, or slopes of embankments along it, from erosion by the current of flow, from floods, etc. (Source: ECHO1a)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > защита берегов
-
16 илистый участок
илистый участок
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
mud flat
A relatively level area of fine silt along a shore (as in a sheltered estuary) or around an island, alternately covered and uncovered by the tide, or covered by shallow water. (Source: BJGEO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > илистый участок
-
17 климат
климат
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
climate
The average weather condition in a region of the world. Many aspects of the Earth's geography affect the climate. Equatorial, or low, latitudes are hotter than the polar latitudes because of the angle at which the rays of sunlight arrive at the Earth's surface. The difference in temperature at the equator and at the poles has an influence on the global circulation of huge masses of air. Cool air at the poles sinks and spreads along the surface of the Earth towards the equator. Cool air forces its way under the lower density warmer air in the lower regions, pushing the lighter air up and toward the poles, where it will cool and descend. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > климат
-
18 компенсация реактивной мощности
компенсация реактивной мощности
-EN
reactive power compensation
an action to optimize the transmission of reactive power in the network as a whole
[МЭС 603-04-28]FR
compensation de l'énergie réactive
action dont le but est d'optimiser globalement le transport d'énergie réactive dans le réseau
[МЭС 603-04-28]Параллельные тексты EN-RU
Reactive energy management
In electrical networks, reactive energy results in increased line currents for a given active energy transmitted to loads.
The main consequences are:
• Need for oversizing of transmission and distribution networks by utilities,
• Increased voltage drops and sags along the distribution lines,
• Additional power losses.
This results in increased electricity bills for industrial customers because of:• Penalties applied by most utilities on reactive energy,
• Increased overall kVA demand,
• Increased energy consumption within the installations.
Reactive energy management aims to optimize your electrical installation by reducing energy consumption, and to improve power availability.
Total CO2 emissions are also reduced.
Utility power bills are typically reduced by 5 % to 10 %.
[Schneider Electric]Компенсация реактивной мощности
Передача по электрической сети реактивной энергии приводит к увеличению линейных токов (по сравнению токами, протекающими при передаче нагрузкам только активной энергии).
Основные последствия этого явления:
● необходимость увеличения сечения проводников в сетях передачи и распределения электроэнергии;
● повышенное падение и провалы напряжения в распределительных линиях;
● дополнительные потери электроэнергии;
Для промышленных потребителей такие потери приводят к возрастанию расходов на оплату электроэнергии, что вызвано:● штрафами, накладываемыми поставщиками электроэнергии за избыточную реактивную мощность;
● увеличением потребления полной мощности (измеряемой в кВА);
● повышенным энергопотреблением электроустановок.Цель компенсации реактивной мощности (КРМ) – оптимизация работы электроустановки за счет сокращения потребления энергии и увеличения надежности электроснабжения. Кроме того, КРМ позволяет уменьшить выбросы CO2 и сократить расходы на электроэнергию в среднем на 5-10 %.
[Перевод Интент]Наиболее эффективным способом снижения потребляемой из сети реактивной мощности является применение установок компенсации реактивной мощности (конденсаторных установок).
Использование конденсаторных установок позволяет:- разгрузить питающие линии электропередачи, трансформаторы и распределительные устройства;
- снизить расходы на оплату электроэнергии;
- при использовании определенного типа установок снизить уровень высших гармоник;
- подавить сетевые помехи, снизить несимметрию фаз;
- увеличить надежность и экономичность распределительных сетей.
На практике коэффициент мощности после компенсации находится в пределах от 0,93 до 0,99.
Наибольший экономический эффект достигается при размещении компенсирующих устройств вблизи электроприемников, потребляющих реактивную мощность.
Различают следующие виды компенсации:-
индивидуальная (нерегулируемая) компенсация
Целесообразна, если мощность электроприемника больше 20 кВт и потребляемая мощность постоянна в течение длительного времени.
Компенсирующая нерегулируемая установка подключается непосредственно у потребителя. Как правило, применяется для компенсации реактивной мощности таких потребителей, как мощные компрессоры, вентиляторы и насосы, силовые трансформаторы. - групповая (нерегулируемая) компенсация
- централизованная компенсация
Для ламп типа ДРЛ, ДРИ, ДРИЗ, ДНаТ может применяться как групповая, так и индивидуальная компенсация реактивной мощности
[ПУЭ]Тематики
Синонимы
Сопутствующие термины
- конденсатор компенсации реактивной мощности
- конденсаторная батарея компенсации реактивной мощности
- контроллер компенсации реактивной мощности
- недостаточная компенсация реактивной мощности
- перекомпенсация реактивной мощности
- потребляемая реактивная мощность
- ступень компенсации реактивной мощности
- установка КРМ
- устройства динамической компенсации реактивной мощности
EN
- energy compensation
- management of reactive energy
- power factor compensation
- reactive energy management
- reactive power compensation
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > компенсация реактивной мощности
-
19 локомотив
локомотив
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
locomotive
A self -propelled engine driven by steam, electricity or diesel power and used for drawing trains along railway tracks. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > локомотив
-
20 мангровое болото
мангровое болото
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
mangrove swamp
A wet, spongy area of land in tropical climates and along coastal regions that is dominated by mangrove trees and shrubs, particularly red mangroves (Rhizophora), black mangroves (Avicennia) and white mangroves (Laguncularia). (Source: FFD)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > мангровое болото
- 1
- 2
См. также в других словарях:
along — [ə lôŋ′] prep. [ME < OE andlang, along, by the side of < and , over against + lang, in length: see LONG1] 1. on or beside the length of; over or throughout the length of [we hiked along the trail; along the driveway there is a hedge] 2. in… … English World dictionary
Along — A*long (?; 115), adv. [OE. along, anlong, AS. andlang, along; pref. and (akin to OFris. ond , OHG. ant , Ger. ent , Goth. and , anda , L. ante, Gr. ?, Skr. anti, over against) + lang long. See {Long}.] 1. By the length; in a line with the length; … The Collaborative International Dictionary of English
Along — A*long [AS. gelang owing to.] (Now heard only in the prep. phrase {along of}.) [1913 Webster] {Along of}, {Along on}, often shortened to {Long of}, prep. phr., owing to; on account of. [Obs. or Low. Eng.] On me is not along thin evil fare.… … The Collaborative International Dictionary of English
Along of — Along A*long [AS. gelang owing to.] (Now heard only in the prep. phrase {along of}.) [1913 Webster] {Along of}, {Along on}, often shortened to {Long of}, prep. phr., owing to; on account of. [Obs. or Low. Eng.] On me is not along thin evil fare.… … The Collaborative International Dictionary of English
Along on — Along A*long [AS. gelang owing to.] (Now heard only in the prep. phrase {along of}.) [1913 Webster] {Along of}, {Along on}, often shortened to {Long of}, prep. phr., owing to; on account of. [Obs. or Low. Eng.] On me is not along thin evil fare.… … The Collaborative International Dictionary of English
along — ► PREPOSITION & ADVERB 1) moving in a constant direction on (a more or less horizontal surface). 2) extending in a more or less horizontal line on. 3) in or into company with others. ● along with Cf. ↑along with ● be (or come) along … English terms dictionary
Along — A*long , prep. By the length of, as distinguished from across. Along the lowly lands. Dryden. [1913 Webster] The kine . . . went along the highway. 1 Sam. vi. 12. [1913 Webster] … The Collaborative International Dictionary of English
along — [adv1] ahead forth, forward, on, onward; concept 581 along [adv2] together with accompanying, additionally, also, as companion, as well, at same time, besides, coupled with, furthermore, in addition to, likewise, moreover, side by side,… … New thesaurus
along — adverb coupled with, forward, in company with, in conjunction with, lengthwise, side by side, together, with Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
Along — (baie d ) (Vinh Ha Long), baie du golfe du Tonkin (ou du Bac Bô), au N. E. de Haiphong. Elle est parsemée d innombrables blocs rocheux percés de grottes. Selon la légende, ce relief accidenté est dû au passage d un dragon (Long) qui descendit des … Encyclopédie Universelle
along — O.E. andlang entire, continuous; extended; all day long; alongside of, from and opposite, against (from P.Gmc. *andi , *anda from PIE *anti against, locative singular of *ant front, forehead; see ANTE (Cf. ante)) + lang long (see LONG … Etymology dictionary