-
1 Kriechstrecke
расстояние утечки
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание. Стык между двумя элементами из изоляционного материала считают частью поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
расстояние утечки (см. приложение В)
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание — При определении расстояния утечки относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9
[ ГОСТ Р 50345-99( МЭК 60898-95)]
расстояние утечки по поверхности
-
[IEV number 151-15-50]
путь утечки
Кратчайшее расстояние вдоль поверхности изоляции между двумя проводящими частями или между проводящей частью и доступной поверхностью.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - A joint between two pieces of insulating material is considered part of the surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - For the purpose of determining a creepage distance to accessible parts, the accessible surface of an insulating enclosure is considered conductive as if it was covered by a metal foil wherever it can be touched by a hand or a standard test finger according to figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
creepage distance
shortest distance along the surface of insulation between two conductive parts or between a conductive part and the accessible surface
[IEC 60335-1, ed. 4.0 (2001-05)]
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts
[IEV number 151-15-50]FR
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Un joint entre deux portions de matière isolante est considéré comme faisant partie de la surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Pour la détermination d'une ligne de fuite pour des parties accessibles, la surface accessible d'une enveloppe isolante est considérée comme conductrice comme si elle était recouverte d'une feuille métallique à tout endroit où elle peut être touchée par la main ou par le doigt d'essai normalisé conforme à la figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
ligne de fuite
plus petite distance le long de la surface de l’isolation entre deux parties conductrices ou entre une partie conductrice et la surface accessible
[IEC 60335-1, ed. 4.0 (2001-05)]
ligne de fuite, f
distance la plus courte, le long de la surface d'un isolant solide, entre deux parties conductrices
[IEV number 151-15-50]1) Должно быть проводящими
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Kriechstrecke
-
2 Kabellängserder
заземляющий электрод подземных кабельных трасс
Заземляющий электрод, обычно проложенный вдоль кабельной трассы в целях заземления этой трассы.
[ ГОСТ Р МЭК 60050-195-2005]EN
underground cable-route earth electrode
earth electrode usually laid along the cable route to provide earthing along its route
Source: 461-06-20 MOD
[IEV number 195-02-28]FR
prise de terre enterrée associée à un câble
prise de terre habituellement posée le long du parcours d'un câble, destinée à assurer la mise à la terre le long du parcours de ce câble
Source: 461-06-20 MOD
[IEV number 195-02-28]Тематики
EN
- underground cable-route earth electrode
- underground cable-route ground electrode (US)
- uninsulated earth conductor (deprecated)
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Kabellängserder
-
3 nicht isolierter Erdleiter (abgelehnt)
заземляющий электрод подземных кабельных трасс
Заземляющий электрод, обычно проложенный вдоль кабельной трассы в целях заземления этой трассы.
[ ГОСТ Р МЭК 60050-195-2005]EN
underground cable-route earth electrode
earth electrode usually laid along the cable route to provide earthing along its route
Source: 461-06-20 MOD
[IEV number 195-02-28]FR
prise de terre enterrée associée à un câble
prise de terre habituellement posée le long du parcours d'un câble, destinée à assurer la mise à la terre le long du parcours de ce câble
Source: 461-06-20 MOD
[IEV number 195-02-28]Тематики
EN
- underground cable-route earth electrode
- underground cable-route ground electrode (US)
- uninsulated earth conductor (deprecated)
DE
FR
Немецко-русский словарь нормативно-технической терминологии > nicht isolierter Erdleiter (abgelehnt)
-
4 Verkehrsunfall
авария на дороге
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
traffic accident
An unexpected incident with potential for harm occurring through the movement or collision of vessels, vehicles or persons along a land, water, air or space route. (Source: OED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Verkehrsunfall
-
5 Busbahnhof
автобусная остановка
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
bus station
A place along a route or line at which a bus stops for fuel or to pick up or let off passengers or goods, especially with ancillary buildings and services. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
автовокзал
Вокзал, размещаемый на конечном или транзитном пункте междугородных или пригородных автобусных маршрутов
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Синонимы
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Busbahnhof
-
6 Luftspalt (2)
воздушный зазор
Кратчайшее расстояние между двумя токоведущими и/или токоведущей и открытой проводящей частью.
МЭК 60050(441-17-31).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
воздушный зазор
Кратчайшее расстояние в воздухе между двумя токопроводящими1) частями вдоль линии наименьшей протяженности между этими токоведущими1) частями.
Примечание. Для определения воздушного зазора относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9.
(МЭС 441-17-31)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
1) Должно быть проводящими
[Интент]
изоляционный промежуток
Расстояние между двумя токопроводящими частями вдоль нити, натянутой по кратчайшему пути между ними.
[ ГОСТ Р 52726-2007]
зазор
Кратчайшее расстояние по воздуху между двумя токопроводящими1) частями оборудования.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
1) Должно быть проводящими
[Интент]EN
clearance
the distance between two conductive parts along a string stretched the shortest way between these conductive parts
[IEV number 441-17-31]
clearance
shortest distance in air between two conductive parts
NOTE – This distance applies only to parts that are exposed to the atmosphere and not to parts which are insulated parts or covered with casting compound.
[IEV number 426-04-12]FR
distance d'isolement
distance entre deux parties conductrices le long d'un fil tendu suivant le plus court trajet possible entre ces deux parties conductrices
[IEV number 441-17-31]
distance d’isolement dans l’air
plus courte distance dans l’air entre deux pièces conductrices
NOTE – Cette distance s'applique seulement aux parties exposées à l'atmosphère et non aux parties isolées ou recouvertes par un composé de moulage.
[IEV number 426-04-12]
Параллельные тексты EN-RU
Clearance distance
Shortest distance in air between two conductive parts or between a conductive part and the accessible surface of the relay.
[Tyco Electronics]Воздушный зазор
Кратчайшее расстояние по воздуху между двумя проводящими частями или между проводящей частью и доступной для прикосновения поверхностью реле.
[Перевод Интент]
Наименьшее изоляционное расстояние по воздуху (в свету) от токоведущих до заземленных частей опоры
[ПУЭ]
2
воздушный зазор
-
[IEV number 151-14-05]EN
air gap
short gap in the magnetic material forming a magnetic circuit
Source: 221-04-13 MOD
[IEV number 151-14-05]FR
entrefer, m
coupure de faible longueur dans le matériau magnétique constituant un circuit magnétique
Source: 221-04-13 MOD
[IEV number 151-14-05]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- air clearance
- air distance
- air gap (2)
- air-gap clearance
- clearance
- contact gap (1)
- contact opening distance (1)
- contact separation (1)
- flashover distance
- insulation clearanse
- insulation distance
- isolating distance
DE
FR
- distance d'isolement
- distance d’isolement dans l’air
- entrefer, m (2)
Немецко-русский словарь нормативно-технической терминологии > Luftspalt (2)
-
7 Luftstrecke
воздушный зазор
Кратчайшее расстояние между двумя токоведущими и/или токоведущей и открытой проводящей частью.
МЭК 60050(441-17-31).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
воздушный зазор
Кратчайшее расстояние в воздухе между двумя токопроводящими1) частями вдоль линии наименьшей протяженности между этими токоведущими1) частями.
Примечание. Для определения воздушного зазора относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9.
(МЭС 441-17-31)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
1) Должно быть проводящими
[Интент]
изоляционный промежуток
Расстояние между двумя токопроводящими частями вдоль нити, натянутой по кратчайшему пути между ними.
[ ГОСТ Р 52726-2007]
зазор
Кратчайшее расстояние по воздуху между двумя токопроводящими1) частями оборудования.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
1) Должно быть проводящими
[Интент]EN
clearance
the distance between two conductive parts along a string stretched the shortest way between these conductive parts
[IEV number 441-17-31]
clearance
shortest distance in air between two conductive parts
NOTE – This distance applies only to parts that are exposed to the atmosphere and not to parts which are insulated parts or covered with casting compound.
[IEV number 426-04-12]FR
distance d'isolement
distance entre deux parties conductrices le long d'un fil tendu suivant le plus court trajet possible entre ces deux parties conductrices
[IEV number 441-17-31]
distance d’isolement dans l’air
plus courte distance dans l’air entre deux pièces conductrices
NOTE – Cette distance s'applique seulement aux parties exposées à l'atmosphère et non aux parties isolées ou recouvertes par un composé de moulage.
[IEV number 426-04-12]
Параллельные тексты EN-RU
Clearance distance
Shortest distance in air between two conductive parts or between a conductive part and the accessible surface of the relay.
[Tyco Electronics]Воздушный зазор
Кратчайшее расстояние по воздуху между двумя проводящими частями или между проводящей частью и доступной для прикосновения поверхностью реле.
[Перевод Интент]
Наименьшее изоляционное расстояние по воздуху (в свету) от токоведущих до заземленных частей опоры
[ПУЭ]
2
воздушный зазор
-
[IEV number 151-14-05]EN
air gap
short gap in the magnetic material forming a magnetic circuit
Source: 221-04-13 MOD
[IEV number 151-14-05]FR
entrefer, m
coupure de faible longueur dans le matériau magnétique constituant un circuit magnétique
Source: 221-04-13 MOD
[IEV number 151-14-05]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- air clearance
- air distance
- air gap (2)
- air-gap clearance
- clearance
- contact gap (1)
- contact opening distance (1)
- contact separation (1)
- flashover distance
- insulation clearanse
- insulation distance
- isolating distance
DE
FR
- distance d'isolement
- distance d’isolement dans l’air
- entrefer, m (2)
Немецко-русский словарь нормативно-технической терминологии > Luftstrecke
-
8 Schlagweite
воздушный зазор
Кратчайшее расстояние между двумя токоведущими и/или токоведущей и открытой проводящей частью.
МЭК 60050(441-17-31).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
воздушный зазор
Кратчайшее расстояние в воздухе между двумя токопроводящими1) частями вдоль линии наименьшей протяженности между этими токоведущими1) частями.
Примечание. Для определения воздушного зазора относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9.
(МЭС 441-17-31)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
1) Должно быть проводящими
[Интент]
изоляционный промежуток
Расстояние между двумя токопроводящими частями вдоль нити, натянутой по кратчайшему пути между ними.
[ ГОСТ Р 52726-2007]
зазор
Кратчайшее расстояние по воздуху между двумя токопроводящими1) частями оборудования.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
1) Должно быть проводящими
[Интент]EN
clearance
the distance between two conductive parts along a string stretched the shortest way between these conductive parts
[IEV number 441-17-31]
clearance
shortest distance in air between two conductive parts
NOTE – This distance applies only to parts that are exposed to the atmosphere and not to parts which are insulated parts or covered with casting compound.
[IEV number 426-04-12]FR
distance d'isolement
distance entre deux parties conductrices le long d'un fil tendu suivant le plus court trajet possible entre ces deux parties conductrices
[IEV number 441-17-31]
distance d’isolement dans l’air
plus courte distance dans l’air entre deux pièces conductrices
NOTE – Cette distance s'applique seulement aux parties exposées à l'atmosphère et non aux parties isolées ou recouvertes par un composé de moulage.
[IEV number 426-04-12]
Параллельные тексты EN-RU
Clearance distance
Shortest distance in air between two conductive parts or between a conductive part and the accessible surface of the relay.
[Tyco Electronics]Воздушный зазор
Кратчайшее расстояние по воздуху между двумя проводящими частями или между проводящей частью и доступной для прикосновения поверхностью реле.
[Перевод Интент]
Наименьшее изоляционное расстояние по воздуху (в свету) от токоведущих до заземленных частей опоры
[ПУЭ]
2
воздушный зазор
-
[IEV number 151-14-05]EN
air gap
short gap in the magnetic material forming a magnetic circuit
Source: 221-04-13 MOD
[IEV number 151-14-05]FR
entrefer, m
coupure de faible longueur dans le matériau magnétique constituant un circuit magnétique
Source: 221-04-13 MOD
[IEV number 151-14-05]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- air clearance
- air distance
- air gap (2)
- air-gap clearance
- clearance
- contact gap (1)
- contact opening distance (1)
- contact separation (1)
- flashover distance
- insulation clearanse
- insulation distance
- isolating distance
DE
FR
- distance d'isolement
- distance d’isolement dans l’air
- entrefer, m (2)
Немецко-русский словарь нормативно-технической терминологии > Schlagweite
-
9 Schlagweite in Luft
воздушный зазор
Кратчайшее расстояние между двумя токоведущими и/или токоведущей и открытой проводящей частью.
МЭК 60050(441-17-31).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
воздушный зазор
Кратчайшее расстояние в воздухе между двумя токопроводящими1) частями вдоль линии наименьшей протяженности между этими токоведущими1) частями.
Примечание. Для определения воздушного зазора относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9.
(МЭС 441-17-31)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
1) Должно быть проводящими
[Интент]
изоляционный промежуток
Расстояние между двумя токопроводящими частями вдоль нити, натянутой по кратчайшему пути между ними.
[ ГОСТ Р 52726-2007]
зазор
Кратчайшее расстояние по воздуху между двумя токопроводящими1) частями оборудования.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
1) Должно быть проводящими
[Интент]EN
clearance
the distance between two conductive parts along a string stretched the shortest way between these conductive parts
[IEV number 441-17-31]
clearance
shortest distance in air between two conductive parts
NOTE – This distance applies only to parts that are exposed to the atmosphere and not to parts which are insulated parts or covered with casting compound.
[IEV number 426-04-12]FR
distance d'isolement
distance entre deux parties conductrices le long d'un fil tendu suivant le plus court trajet possible entre ces deux parties conductrices
[IEV number 441-17-31]
distance d’isolement dans l’air
plus courte distance dans l’air entre deux pièces conductrices
NOTE – Cette distance s'applique seulement aux parties exposées à l'atmosphère et non aux parties isolées ou recouvertes par un composé de moulage.
[IEV number 426-04-12]
Параллельные тексты EN-RU
Clearance distance
Shortest distance in air between two conductive parts or between a conductive part and the accessible surface of the relay.
[Tyco Electronics]Воздушный зазор
Кратчайшее расстояние по воздуху между двумя проводящими частями или между проводящей частью и доступной для прикосновения поверхностью реле.
[Перевод Интент]
Наименьшее изоляционное расстояние по воздуху (в свету) от токоведущих до заземленных частей опоры
[ПУЭ]
2
воздушный зазор
-
[IEV number 151-14-05]EN
air gap
short gap in the magnetic material forming a magnetic circuit
Source: 221-04-13 MOD
[IEV number 151-14-05]FR
entrefer, m
coupure de faible longueur dans le matériau magnétique constituant un circuit magnétique
Source: 221-04-13 MOD
[IEV number 151-14-05]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- air clearance
- air distance
- air gap (2)
- air-gap clearance
- clearance
- contact gap (1)
- contact opening distance (1)
- contact separation (1)
- flashover distance
- insulation clearanse
- insulation distance
- isolating distance
DE
FR
- distance d'isolement
- distance d’isolement dans l’air
- entrefer, m (2)
Немецко-русский словарь нормативно-технической терминологии > Schlagweite in Luft
-
10 Potentialglättung
выравнивание потенциалов
Метод снижения напряжения прикосновения и шага между точками электрической цепи, к которым возможно одновременное прикосновение или на которых может одновременно стоять человек
[ ГОСТ 12.1.009-76]
выравнивание потенциала
-
[IEV number 151-15-51]EN
potential grading
reduction of substantial inequalities of electric field strength in or along an insulator or insulation by constructional measures
[IEV number 151-15-51]FR
répartition des potentiels, f
réduction des inégalités importantes du champ électrique à l'intérieur ou à la surface d'un isolateur ou d'une isolation par des moyens incorporés au dispositif
[IEV number 151-15-51]Тематики
EN
DE
FR
- répartition des potentiels, f
Немецко-русский словарь нормативно-технической терминологии > Potentialglättung
-
11 Quellband, n
гигроскопичная лента
водонабухающая лента
лента, применяемая под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-16]EN
water blocking tape
swelling tape
tape applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-16]FR
ruban d'étanchéité
ruban gonflant
ruban appliqué sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-16]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellband, n
FR
Немецко-русский словарь нормативно-технической терминологии > Quellband, n
-
12 Quellpulver, n
гигроскопичная пудра
водонабухающая пудра
порошковый наполнитель, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-14]EN
water blocking powder
swelling powder
powder applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-14]FR
poudre d'étanchéité
poudre gonflante
poudre appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-14]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellpulver, n
FR
Немецко-русский словарь нормативно-технической терминологии > Quellpulver, n
-
13 Quellmasse, f
гигроскопичный клей
водонабухающий клей
клей, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-17]EN
water blocking glue
swelling glue
glue applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-17]FR
matière d'étanchéité
matière appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-17]
Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellmasse, f
FR
Немецко-русский словарь нормативно-технической терминологии > Quellmasse, f
-
14 X-Y-Schreiber
двухкоординатный самописец
-
[IEV number 313-02-04]EN
X-Y recorder
recording instrument in which the marking device is moved along two orthogonal axes by two separate devices, to each of which a quantity to be recorded is applied
[IEV number 313-02-04]FR
enregistreur X-Y
appareil enregistreur dans lequel le dispositif d'inscription est déplacé le long de deux axes orthogonaux par deux dispositifs distincts à chacun desquels est appliquée une grandeur à enregistrer
[IEV number 313-02-04]Тематики
- измерение электр. величин в целом
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > X-Y-Schreiber
-
15 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
16 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
17 Straßenverkehrssicherheit
дорожная безопасность
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
road safety
Any measure, technique or design intended to reduce the risk of harm posed by moving vehicles along a constructed land route. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Straßenverkehrssicherheit
-
18 Bahnhof (Eisenbahn)
железнодорожная станция
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
railway station
A place along a route or line at which a train stops to pick up or let off passengers or goods, especially with ancillary buildings and services. (Source: CED)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Bahnhof (Eisenbahn)
-
19 Wohngebiet (mit Verkehrsberuhigung)
- жилой район с дорогами, оборудованными устройствами по контролю за скоростью
жилой район с дорогами, оборудованными устройствами по контролю за скоростью
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
residential area with traffic calmings
Residential zones where raised areas are built across roads so that vehicles are forced to move more slowly along it. (Source: CAMB)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Wohngebiet (mit Verkehrsberuhigung)
-
20 Uferschutz
защита берегов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
bank protection
Engineering work which aims at the protection of banks of a river, or slopes of embankments along it, from erosion by the current of flow, from floods, etc. (Source: ECHO1a)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Uferschutz
См. также в других словарях:
along — [ə lôŋ′] prep. [ME < OE andlang, along, by the side of < and , over against + lang, in length: see LONG1] 1. on or beside the length of; over or throughout the length of [we hiked along the trail; along the driveway there is a hedge] 2. in… … English World dictionary
Along — A*long (?; 115), adv. [OE. along, anlong, AS. andlang, along; pref. and (akin to OFris. ond , OHG. ant , Ger. ent , Goth. and , anda , L. ante, Gr. ?, Skr. anti, over against) + lang long. See {Long}.] 1. By the length; in a line with the length; … The Collaborative International Dictionary of English
Along — A*long [AS. gelang owing to.] (Now heard only in the prep. phrase {along of}.) [1913 Webster] {Along of}, {Along on}, often shortened to {Long of}, prep. phr., owing to; on account of. [Obs. or Low. Eng.] On me is not along thin evil fare.… … The Collaborative International Dictionary of English
Along of — Along A*long [AS. gelang owing to.] (Now heard only in the prep. phrase {along of}.) [1913 Webster] {Along of}, {Along on}, often shortened to {Long of}, prep. phr., owing to; on account of. [Obs. or Low. Eng.] On me is not along thin evil fare.… … The Collaborative International Dictionary of English
Along on — Along A*long [AS. gelang owing to.] (Now heard only in the prep. phrase {along of}.) [1913 Webster] {Along of}, {Along on}, often shortened to {Long of}, prep. phr., owing to; on account of. [Obs. or Low. Eng.] On me is not along thin evil fare.… … The Collaborative International Dictionary of English
along — ► PREPOSITION & ADVERB 1) moving in a constant direction on (a more or less horizontal surface). 2) extending in a more or less horizontal line on. 3) in or into company with others. ● along with Cf. ↑along with ● be (or come) along … English terms dictionary
Along — A*long , prep. By the length of, as distinguished from across. Along the lowly lands. Dryden. [1913 Webster] The kine . . . went along the highway. 1 Sam. vi. 12. [1913 Webster] … The Collaborative International Dictionary of English
along — [adv1] ahead forth, forward, on, onward; concept 581 along [adv2] together with accompanying, additionally, also, as companion, as well, at same time, besides, coupled with, furthermore, in addition to, likewise, moreover, side by side,… … New thesaurus
along — adverb coupled with, forward, in company with, in conjunction with, lengthwise, side by side, together, with Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
Along — (baie d ) (Vinh Ha Long), baie du golfe du Tonkin (ou du Bac Bô), au N. E. de Haiphong. Elle est parsemée d innombrables blocs rocheux percés de grottes. Selon la légende, ce relief accidenté est dû au passage d un dragon (Long) qui descendit des … Encyclopédie Universelle
along — O.E. andlang entire, continuous; extended; all day long; alongside of, from and opposite, against (from P.Gmc. *andi , *anda from PIE *anti against, locative singular of *ant front, forehead; see ANTE (Cf. ante)) + lang long (see LONG … Etymology dictionary