-
1 effet ŕ long terme
долгосрочное воздействие
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
long-term effect
Effects which will last long after the cause has ceased. (Source: RRDA)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > effet ŕ long terme
-
2 courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant admissible, m
-
3 courant permanent admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Франко-русский словарь нормативно-технической терминологии > courant permanent admissible, m
-
4 bilan hydrologique
биологический баланс воды
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biological water balance
The amount of ingoing and outgoing water in a system, which are assumed to be equal in the long term so that the water budget will balance. (Source: ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
гидрологический баланс
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
hydrologic balance
An accounting of the inflow to, outflow from, and storage in a hydrologic unit such as a drainage basin, aquifer, soil zone, lake or reservoir; the relationship between evaporation, precipitation, runoff, and the change in water storage. (Source: BJGEO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > bilan hydrologique
-
5 conducteur de protection (déconseillé dans ce sens)
экранирующий провод
отдельный провод или одножильный кабель, проложенный параллельно кабелю или кабельному каналу, являющийся частью замкнутой цепи, по которой могут проходить наведенные токи, магнитное поле которых будет противоположно полю в кабеле (ях)
[IEV number 461-12-01]EN
shielding conductor
separate conductor or single-core cable laid parallel to a cable or cable circuit and itself forming part of a closed circuit in which induced currents may flow whose magnetic field will oppose the field caused by the current in the cable(s)
[IEV number 461-12-01]FR
conducteur écran
conducteur de protection (déconseillé dans ce sens)
conducteur séparé ou câble à un conducteur posé parallèlement le long d'un câble ou d'un circuit de câbles et faisant lui-même partie d'un circuit fermé dans lequel peuvent circuler des courants induits dont le champ magnétique s'oppose à celui produit par les courants circulant dans le ou les câbles
[IEV number 461-12-01]Тематики
- кабели, провода...
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > conducteur de protection (déconseillé dans ce sens)
-
6 conducteur écran
экранирующий провод
отдельный провод или одножильный кабель, проложенный параллельно кабелю или кабельному каналу, являющийся частью замкнутой цепи, по которой могут проходить наведенные токи, магнитное поле которых будет противоположно полю в кабеле (ях)
[IEV number 461-12-01]EN
shielding conductor
separate conductor or single-core cable laid parallel to a cable or cable circuit and itself forming part of a closed circuit in which induced currents may flow whose magnetic field will oppose the field caused by the current in the cable(s)
[IEV number 461-12-01]FR
conducteur écran
conducteur de protection (déconseillé dans ce sens)
conducteur séparé ou câble à un conducteur posé parallèlement le long d'un câble ou d'un circuit de câbles et faisant lui-même partie d'un circuit fermé dans lequel peuvent circuler des courants induits dont le champ magnétique s'oppose à celui produit par les courants circulant dans le ou les câbles
[IEV number 461-12-01]Тематики
- кабели, провода...
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > conducteur écran
См. также в других словарях:
will go a long way — (someone) will go a long way to be very successful. She is an excellent actor, and I know she ll go a long way … New idioms dictionary
someone will go a long way — (someone) will go a long way to be very successful. She is an excellent actor, and I know she ll go a long way … New idioms dictionary
Long (Bloody Roar) — Long (ロン) is a fictional character from the Bloody Roar series. He is one of a few characters to have appeared in every game of the series.Affiliation*Shenlong His Clone/Friendly Rival *Uriko Former Student *Alice Friend *Fox May Have Worked With … Wikipedia
long — long1 W1S1 [lɔŋ US lo:ŋ] adj comparative longer superlative longest ▬▬▬▬▬▬▬ 1¦(great length)¦ 2¦(great distance)¦ 3¦(large amount of time)¦ 4¦(particular length/distance/time)¦ 5¦(writing)¦ 6¦(clothing)¦ 7¦(tiring/boring)¦ … Dictionary of contemporary English
long — long1 W1S1 [lɔŋ US lo:ŋ] adj comparative longer superlative longest ▬▬▬▬▬▬▬ 1¦(great length)¦ 2¦(great distance)¦ 3¦(large amount of time)¦ 4¦(particular length/distance/time)¦ 5¦(writing)¦ 6¦(clothing)¦ 7¦(tiring/boring)¦ … Dictionary of contemporary English
long — long1 [ lɔŋ ] adjective *** ▸ 1 measurement/distance ▸ 2 lasting long time ▸ 3 measuring distance/time ▸ 4 book/letter/list ▸ 5 clothes ▸ 6 about ball in sports ▸ 7 drink: in tall glass ▸ 8 about vowel ▸ + PHRASES 1. ) measuring a large amount… … Usage of the words and phrases in modern English
Will & Grace — Infobox Television show name = Will Grace caption = rated = format = Sitcom runtime = approx. 23 minutes creator = David Kohan Max Mutchnick director = James Burrows starring = Eric McCormack Debra Messing Sean Hayes Megan Mullally Shelley… … Wikipedia
long — I UK [lɒŋ] / US [lɔŋ] adjective Word forms long : adjective long comparative longer superlative longest *** 1) lasting for a large amount of time It s a long time since I saw Rachel. There was a long pause before he spoke. Many people face a long … English dictionary
Long track speed skating — For related forms of competition, see Speed skating. Competitive speed skater Speed skating (also long track speed skating) is an Olympic sport where competitors are timed while crossing a set distance. It is also a sport for leisure. Sports such … Wikipedia
long*/*/*/ — [lɒŋ] adj I 1) lasting for a large amount of time Ant: short He has a long history of mental illness.[/ex] It s a long time since I saw Rachel.[/ex] 2) measuring a large amount from one end to the other Ant: short It s the longest tunnel in… … Dictionary for writing and speaking English
long — 1 adjective 1 OBJECT/LINE measuring a great length or a greater length than usual from one end to the other: Cher used to have really long hair. | The line to get into the movie was so long we gave up. | The Aleutian Islands form the longest… … Longman dictionary of contemporary English
