-
1 high-wet-modulus-Faser
Das Deutsch-Russische Wörterbuch der Kunststoff und Kautschuk, Chemiefasern, Farben und Lacke > high-wet-modulus-Faser
-
2 Spieß
den Spieß umdrehen odda(wa)ć wet za wet, odwzajemni(a)ć się tym samym -
3 Scheinanlauf
ложный запуск ГТД
ложный запуск
ЛЗ
Принудительная раскрутка, ротора ГТД пусковым устройством с подачей топлива в камеру сгорания при выключенной системе зажигания.
[ ГОСТ 23851-79]Тематики
Синонимы
EN
DE
FR
232. Ложный запуск ГТД
Ложный запуск
ЛЗ
D. Scheinanlauf
Е. Wet motoring
F. Démarrage faux
Принудительная раскрутка ротора ГТД пусковым устройством с подачей топлива в камеру сгорания при выключенной системе зажигания
Источник: ГОСТ 23851-79: Двигатели газотурбинные авиационные. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Scheinanlauf
-
4 Nassmischen
мокрое смешивание металлических порошков
мокрое смешивание
Смешивание металлических порошков с добавлением жидких веществ, препятствующих разделению смеси по компонентам.
[ ГОСТ 17359-82]Тематики
Синонимы
EN
DE
FR
12. Мокрое смешивание металлических порошков
Мокрое смешивание
D. Nassmischen
Е. Wet mixing
F. Mélange humide
Источник: ГОСТ 17359-82: Порошковая металлургия. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Nassmischen
-
5 Naßverfahren
мокрый процесс
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
wet process
Process used to remove particulate matter and/or gaseous pollutants by means of an aqueous stream or slurry. (Source: KORENa)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Naßverfahren
-
6 Naßabscheider
мокрый скруббер
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
wet scrubber
1) An air cleaning device that literally washes out the dust. Exhaust air is forced into a spray chamber, where fine water particles cause the dust to drop from the air stream. The dust-ladden water is then treated to remove the solid material and is often recirculated. 2) Equipment through which a gas is passed to remove impurities (solid, liquid, or gaseous particles) by intimate contact with a suitable liquid, usually an aqueous medium. (Source: LANDY / BRACK / ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Naßabscheider
-
7 Filterrückstand
осадок на фильтре
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
filter cake
Accumulated solids, wet or dry, generated by any filtration process, including accumulation on fabric filters in air filtering processes, or accumulation of wet solids in liquid filtering processes. (Source: EED / ISEP)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Filterrückstand
-
8 Sattdampfturbine
паровая стационарная турбина насыщенного пара
турбина насыщенного пара
Паровая стационарная турбина, в которой используется в качестве свежего насыщенный пар.
[ ГОСТ 23269-78]Тематики
Синонимы
EN
DE
FR
18. Паровая стационарная турбина насыщенного пара
Турбина насыщенного пара
D. Sattdampfturbine
E. Wet steam turbine
F. Turbine a vapeur saturee
Паровая стационарная турбина, в которой используется в качестве свежего насыщенный пар
Источник: ГОСТ 23269-78: Турбины стационарные паровые. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Sattdampfturbine
-
9 Feuerung mit flussiger Entschlackung
топка стационарного котла с жидким шлакоудалением
[ ГОСТ 23172-78]Тематики
- котел, водонагреватель
EN
DE
107. Топка стационарного котла с жидким шлакоудалением
D. Feuerung mit flussiger Entschlackung
E. Wet-bottom or slag-tap furnace
-
Источник: ГОСТ 23172-78: Котлы стационарные. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Feuerung mit flussiger Entschlackung
-
10 Sonne
1) со́лнце [он]. die goldene Sonne золото́е <злато́е> со́лнце. die liebe Sonne я́сное со́лнышко. die schöne Sonne (кра́сно) со́лнышко. die Sonne versinkt im Meer со́лнце захо́дит за мо́рем. bevor < ehe> die Sonne aufgeht до восхо́да со́лнца. etw. hat den ganzen Tag Sonne v. Wohnung, Zimmer в чём-н. весь день со́лнце. etw. brauch viel Sonne что-н. о́чень нужда́ется в со́лнце, чему́-н. ну́жно мно́го со́лнца. in <an> der Sonne liegen, sitzen на со́лнце. in der prallen Sonne liegen, sitzen на солнцепёке. in die Sonne gehen, sehen, sich setzen, sich legen на со́лнце. sich von der Sonne bräunen lassen загора́ть /-горе́ть на со́лнце geh'mir aus der Sonne! не заслоня́й (мне) свет ! die Sonne bringt es an den Tag, alles kommt ans Licht der Sonne ши́ла в мешке́ не утаи́шь. jd. ist nicht wet, daß ihn die Sonne bescheint кто-н. недосто́ин жить на земле́. wie Butter an der Sonne schmelzen a) v. Hoffnung мгнове́нно проходи́ть пройти́ b) v. (finanziellen) Mitteln бы́стро та́ять /pac- <исчеза́ть/исче́знуть>. mit der Sonne aufstehen встава́ть /-стать с пе́рвыми луча́ми со́лнца. der Glücklichste < glücklichste Mensch> unter der Sonne счастли́вейший из сме́ртных2) Astrologie Со́лнце -
11 HWM-Faser
fDas Deutsch-Russische Wörterbuch der Kunststoff und Kautschuk, Chemiefasern, Farben und Lacke > HWM-Faser
-
12 naßfestes Papier
влагопрочная бумага
Бумага, подвергнутая специальной поверхностной обработке или обработке в массе для повышения прочности во влажном состоянии.
[ ГОСТ 17586-80]Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > naßfestes Papier
-
13 Naßfestigkeit
влагопрочность бумаги (картона)
Свойство бумаги (картона) сохранять прочность при увлажнении.
[ ГОСТ 17052-86]Тематики
EN
DE
FR
- résistance apparente à l’état humide
Немецко-русский словарь нормативно-технической терминологии > Naßfestigkeit
-
14 Naßdampf
влажный пар
Равновесная смесь, состоящая из паровой и жидкой фаз.
[Сборник рекомендуемых терминов. Выпуск 103. Термодинамика. Академия наук СССР. Комитет научно-технической терминологии. 1984 г.]
влажный пар
-
[Лугинский Я. Н. и др. Англо-русский словарь по электротехнике и электроэнергетике. 2-е издание - М.: РУССО, 1995 - 616 с.]
Тематики
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Naßdampf
-
15 Glockengasbehälter
газгольдер многозвенный
Мокрый газгольдер, имеющий подвижные звенья в виде колокола с одним или несколькими телескопами, соединёнными между собой кольцевыми затворами
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
DE
FR
газгольдер мокрый
Газгольдер переменного объёма с нижним стальным или железобетонным резервуаром, наполненным водой, и верхними стальными подъёмными и опускными звеньями, наполненными газом
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Glockengasbehälter
-
16 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
17 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
-
18 Druckstrahl-Putzkammer
дробеструйная камера
Установка для очистки отливок потоком дроби, выбрасываемой одним или несколькими дробеструйными аппаратами, с периодической подачей отливок.
[ ГОСТ 18111-93]Тематики
Обобщающие термины
EN
DE
Немецко-русский словарь нормативно-технической терминологии > Druckstrahl-Putzkammer
-
19 Druckstrahllappen
жидкостно-абразивная обработка
Ндп. гидроабразивная обработка
галтовка
Абразивная обработка, осуществляемая при движении заготовки и абразивных зерен относительно друг друга в жидкости в замкнутой емкости.
[ ГОСТ 23505-79]Недопустимые, нерекомендуемые
Тематики
- обработка абразивная, абразивы
EN
DE
Немецко-русский словарь нормативно-технической терминологии > Druckstrahllappen
-
20 Brennkammer
камера горения топки стационарного котла
камера горения
Часть топки стационарного котла, в которой происходит воспламенение и горение основной массы топлива.
[ ГОСТ 23172-78]Тематики
- котел, водонагреватель
Синонимы
EN
DE
FR
камера сгорания ГТД
камера сгорания
Ндп. камера горения ГТД
Устройство, в котором в результате сгорания топлива осуществляется повышение температуры поступающего в него воздуха (газа).
[ ГОСТ 23851-79]Недопустимые, нерекомендуемые
Тематики
Синонимы
EN
DE
FR
121. Камера сгорания ГТД
Камера сгорания
Ндп. Камера горения
D. Brennkammer
Е. Combustion chamber
F. Chambre de combustion
Устройство, в котором в результате сгорания топлива осуществляется повышение температуры поступающего в него воздуха (газа)
Источник: ГОСТ 23851-79: Двигатели газотурбинные авиационные. Термины и определения оригинал документа
116. Камера горения топки стационарного котла
Камера горения
D. Brennkammer
E. Primary furnace (in wetbottom-furnace)
F. Chambre de combustion
Часть топки стационарного котла, в которой происходят воспламенение и горение основной массы топлива
Источник: ГОСТ 23172-78: Котлы стационарные. Термины и определения оригинал документа
Немецко-русский словарь нормативно-технической терминологии > Brennkammer
- 1
- 2
См. также в других словарях:
wet — [wet] adj. wetter, wettest [ME < OE wæt, akin to ON vatr: for IE base see WATER] 1. moistened, covered, or saturated with water or other liquid 2. rainy; foggy; misty [a wet day] 3. not yet dry [wet paint] 4 … English World dictionary
Wet — (w[e^]t), a. [Compar. {Wetter}; superl. {Wettest}.] [OE. wet, weet, AS. w[=ae]t; akin to OFries. w[=e]t, Icel. v[=a]tr, Sw. v[*a]t, Dan. vaad, and E. water. [root]137. See {Water}.] [1913 Webster] 1. Containing, or consisting of, water or other… … The Collaborative International Dictionary of English
wet*/*/*/ — [wet] adj I 1) covered with water or another liquid You d better come in or you ll get wet.[/ex] My socks and shoes were soaking wet (= very wet).[/ex] Her forehead was wet with sweat.[/ex] Where have you been? You re wet through (= completely… … Dictionary for writing and speaking English
wet — wet, damp, dank, moist, humid are comparable when they mean covered or more or less soaked with liquid. Wet may be used with no further implications or it may specifically imply saturation {wet clothes} {the rain lies in puddles on the wet… … New Dictionary of Synonyms
WET — ist die Abkürzung für: Weightless Environmental Test, Erprobung von Raumfahrttechnik und arbeitsweisen in simulierter Schwerelosigkeit, für gewöhnlich in Wassertanks mit Modellen deren Auftrieb ihre Gewichtskraft aufhebt (neutral buoyancy) Wert… … Deutsch Wikipedia
wet — ► ADJECTIVE (wetter, wettest) 1) covered or saturated with liquid. 2) (of the weather) rainy. 3) involving the use of water or liquid. 4) (of paint, ink, etc.) not yet having dried or hardened. 5) Brit. informal lacking forcefulness or strength… … English terms dictionary
Wet — Wet, v. t. [imp. & p. p. {Wet} (rarely {Wetted}); p. pr. & vb. n. {Wetting}.] [AS. w[=ae]tan.] To fill or moisten with water or other liquid; to sprinkle; to cause to have water or other fluid adherent to the surface; to dip or soak in a liquid;… … The Collaborative International Dictionary of English
Wet — Wet, v. t. [imp. & p. p. {Wet} (rarely {Wetted}); p. pr. & vb. n. {Wetting}.] [AS. w[=ae]tan.] To fill or moisten with water or other liquid; to sprinkle; to cause to have water or other fluid adherent to the surface; to dip or soak in a liquid;… … The Collaborative International Dictionary of English
Wet — could refer to: * The condition of being liquid or being covered in liquid * Wet (album), an album released in 1979 by Barbra Streisand * The wets, moderate members of the British Conservative Party * Phencyclidine (PCP), a dissociative… … Wikipedia
Wet — Cette page d’homonymie répertorie les différents sujets et articles partageant un même nom … Wikipédia en Français
Wet — может означать: Западноевропейское время (Western European Time, WET) нулевой часовой пояс. Wet музыкальный альбом Барбры Стрейзанд «Wet» сингл Снуп Догга с его одиннадцатого альбома «Doggumentary». WET компьютерная игра.… … Википедия