-
1 коэффициент искажения синусоидальности кривой напряжения (тока)
- Facteur de distortion (d’une tension ou d’un courant alternative non sinusoïdal)
- facteur de distortion (d’une tension ou d’un courant alternatif non sinusoïdal)
коэффициент искажения синусоидальности кривой напряжения (тока)
Величина, равная отношению действующего значения суммы гармонических составляющих к действующему значению основной составляющей переменного напряжения (тока).
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току).
[ ГОСТ 23875-88]
коэффициент нелинейных искажений
коэффициент несинусоидальности
КНИ
Определяет веса высших гармоник переменного напряжения по отношению к основной гармонике. Чем КНИ меньше, тем ближе форма напряжения к чистой синусоиде. Например: синусоидальная форма сигнала (КНИ=0), форма сигнала отлична от синусоидальной, но искажения не заметны на глаз (КНИ<3%), отклонение формы сигнала от синусоидальной заметно на глаз (КНИ>5%), сигнал имеет трапецеидальную или ступенчатую форму (КНИ<21%), сигнал имеет прямоугольную форму (КНИ=43%)
[ http://www.radistr.ru/misc/document423.phtml]
(полный) коэффициент гармоник
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва]EN
total harmonic distortions
THD
RMS value of all harmonics in a waveform (excluding fundamental) divided by RMS value of fundamental. THDV refers to Voltage waveform. THDI refers to Current waveform.
[ http://www.upsonnet.com/UPS-Glossary/]total 3rd order harmonic distortion
коэффициент искажения синусоидальности, вызванный гармоническими составляющими третьего порядка
total harmonic distortion; THD
коэффициент искажения синусоидальности
общий коэффициент несинусоидальностиtotal harmonic current distortion; THDI
коэффициент искажения синусоидальности кривой тока
обшее гармоническое искажение токаtotal harmonic voltage distortion; THDV, THDU
коэффициент искажения синусоидальности кривой напряжения
обшее гармоническое искажение напряженияПараллельные тексты EN-RU
THD is the ratio of harmonic content to the fundamental and provides a general indication of the quality of a waveform.
[Schneider Electric]Коэффициент искажения синусоидальности (THD) представляет собой отношение суммы гармонических составляющих к значению основной составляющей и является основным индикатором качества формы электрического сигнала.
[Перевод Интент]
Тематики
Синонимы
- КНИ
- коэффициент гармоник
- коэффициент искажения
- коэффициент нелинейных искажений
- коэффициент несинусоидальности
- полный коэффициент гармоник
EN
- distortion factor (of a non-sinusoidal alternating voltage or current)
- THD
- total harmonic distortions
DE
FR
- facteur de distortion (d’une tension ou d’un courant alternatif non sinusoïdal)
Смотри также
55. Коэффициент искажения синусоидальности кривой напряжения (тока)
Коэффициент искажения
D. Klirrfaktor
E. Distortion factor (of a non-sinusoidal alternating voltage or current)
F. Facteur de distortion (d’une tension ou d’un courant alternative non sinusoïdal)
Величина, равная отношению действующего значения суммы гармонических составляющих к действующему значению основной составляющей переменного напряжения (тока).
Примечание. Для целей стандартизации допускается относить к номинальному напряжению (току)
Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > коэффициент искажения синусоидальности кривой напряжения (тока)
2 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
3 коэффициент подавления общего вида
коэффициент подавления общего вида
-
[IEV number 312-06-21]EN
common mode rejection ratio
CMRR (abbreviation)
ratio of the voltage applied between a specified reference point and the input terminals, when connected together by a specified circuit, to the voltage required between the input terminals to produce the same value of the output
NOTE 1 – The common mode rejection ratio is usually expressed in decibels and can depend on the frequency, the waveform and the method of measurement.
NOTE 2 – Common mode rejection ratio can also apply to quantities other than voltage.
[IEV number 312-06-21]FR
rapport de réjection de mode commun
rapport de la tension appliquée entre un point de référence spécifié et les deux bornes d'entrée connectées l'une à l'autre par un circuit spécifié, à la tension nécessaire entre les bornes d'entrée pour produire la même valeur de sortie
NOTE 1 – Le facteur de réjection de mode commun est généralement exprimé en décibels et peut dépendre de la fréquence, de la forme d’onde et de la méthode de mesure.
NOTE 2 – Le rapport de réjection de mode commun peut aussi s'appliquer à des grandeurs autres que les tensions.
[IEV number 312-06-21]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > коэффициент подавления общего вида
4 коэффициент подавления при последовательном включении
коэффициент подавления при последовательном включении
-
[IEV number 312-06-22]EN
series mode rejection ratio
SMRR (abbreviation)
ratio of the series mode voltage causing a specified change in output information, to the voltage initiated by the measurand which would produce the same change
NOTE 1 – The series mode rejection ratio is usually expressed in decibels and may depend on the frequency, the waveform and the method of measurement.
NOTE 2 – Series mode rejection ratio can also apply to quantities other than voltage.
[IEV number 312-06-22]FR
rapport de réjection de mode série
rapport de la tension de mode série, provoquant un changement spécifié d'information de sortie, à la tension résultant du mesurande qui produirait le même changement
NOTE 1 – Le facteur de réjection de mode série est généralement exprimé en décibels et peut dépendre de la fréquence, de la forme d’onde et de la méthode de mesure.
NOTE 2 – Le rapport de réjection de mode commun peut aussi s'appliquer à des grandeurs autres que les tensions.
[IEV number 312-06-22]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > коэффициент подавления при последовательном включении
5 генератор сигналов для измерительных целей
генератор сигналов для измерительных целей
-
[IEV number 312-02-41]EN
signal generator (for measuring purposes)
source of electrical signals, whose characteristics (waveform, frequency, voltage, etc.) can be fixed, or controlled within specified limits
[IEV number 312-02-41]FR
générateur de signaux (à usage de mesure)
source de signaux électriques dont les caractéristiques (forme d'onde, fréquence, tension, etc.) peuvent être fixées, ou réglées dans des limites spécifiées
[IEV number 312-02-41]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > генератор сигналов для измерительных целей
См. также в других словарях:
Voltage regulator — A popular three pin 12 V DC voltage regulator IC. A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. A voltage regulator may be a simple feed forward design or may include negative feedback … Wikipedia
Voltage doubler — A voltage doubler is an electronic circuit which charges capacitors from the input voltage and switches these charges in such a way that, in the ideal case, exactly twice the voltage is produced at the output as at its input. The simplest of… … Wikipedia
Waveform monitor — A waveform monitor is a special type of oscilloscope used in television applications. It is typically used to measure and display the level, or voltage, of a video signal with respect to time.The level of a video signal usually corresponds to the … Wikipedia
Voltage-controlled oscillator — A voltage controlled oscillator or VCO is an electronic oscillator designed to be controlled in oscillation frequency by a voltage input. The frequency of oscillation is varied by the applied DC voltage, while modulating signals may also be fed… … Wikipedia
Voltage-controlled filter — A voltage controlled filter (VCF) is an electronic filter whose operating characteristics can be controlled by means of a control voltage applied to one or more inputs. [citebook|title=Analog Days C: the invention and impact of the Moog… … Wikipedia
Waveform — The shape of the curve graphically representing the change in the ac signal voltage and current amplitude, with respect to time. Solar Electric Glossary … Energy terms
Waveform — A&V The shape of an electromagnetic wave. A graphical representation of voltage or current in relation to time … Audio and video glossary
Laser Voltage Prober — The Laser Voltage Probe (LVP) is a laser based voltage and timing waveform acquisition system which is used to perform failure analysis on flip chip integrated circuits. The device to be analyzed is de encapsulated in order to expose the silicon… … Wikipedia
Arbitrary waveform generator — An arbitrary waveform generator (AWG) is a piece of electronic test equipment used to generate electrical waveforms. These waveforms can be either repetitive or single shot (once only) in which case some kind of triggering source is required… … Wikipedia
Peak inverse voltage — The peak inverse voltage is the specified maximum voltage that a diode rectifier will block.In semiconductor diodesAs a general term applied to semiconductor diodes, peak reverse voltage or peak inverse voltage is the maximum voltage that a diode … Wikipedia
Inverter (electrical) — An inverter is an electrical device that converts direct current (DC) to alternating current (AC)[1]; the converted AC can be at any required voltage and frequency with the use of appropriate transformers, switching, and control circuits. Solid… … Wikipedia
Перевод: со всех языков на французский
с французского на все языки- С французского на:
- Все языки
- Со всех языков на:
- Все языки
- Английский
- Испанский
- Немецкий
- Русский
- Финский
- Французский