Перевод: с русского на французский

с французского на русский

value+is+assigned+to

  • 1 номинальное напряжение

    1. Un
    2. tension nominale
    3. tension assignée

     

    номинальное напряжение
    Напряжение, установленное изготовителем для прибора
    [ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]

    номинальное напряжение Uном, кВ
    Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
    [ ГОСТ Р 52726-2007]

    номинальное напряжение

    Un
    Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    rated voltage
    voltage assigned to the appliance by the manufacturer
    [IEC 60335-1, ed. 4.0 (2001-05)]

    rated voltage
    quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    rated voltage
    input or output supply voltage for which equipment is designed or specified
    [IEC 88528-11, ed. 1.0 (2004-03)]

    rated voltage
    specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
    NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    rated voltage
    the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
    NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    rated voltage
    reference voltage for which the cable is designed, and which serves to define the electrical tests
    NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
    Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
    U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
    In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
    This condition applies both to the value Uo and to the value U.
    In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
    NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
    [IEC 60245-1, ed. 4.0 (2003-12)]

    rated voltage
    highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
    [IEC 60800, ed. 3.0 (2009-07)]

    rated voltage
    the r.m.s. line-to-line voltage under rated conditions
    Primary side of input transformer: ULN
    Converter input: UVN
    Converter output: UaN
    Motor voltage: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    rated voltage
    input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
    [IEC 62040-1, ed. 1.0 (2008-06)]

    nominal voltage, Un
    voltage by which a system is designated or identified
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension assignée
    tension attribuée à l'appareil par le fabricant
    [IEC 60335-1, ed. 4.0 (2001-05)]

    tension nominale
    tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    tension assignée
    tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
    NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    tension assignée
    valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
    NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    tension assignée
    tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
    NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
    Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
    U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
    Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
    Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
    Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
    NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
    [IEC 60245-1, ed. 4.0 (2003-12)]

    tension assignée
    tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
    [IEC 60800, ed. 3.0 (2009-07)]

    tension assignée
    valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
    Primaire du transformateur d’entrée: ULN
    Entrée du convertisseur: UVN
    Sortie du convertisseur: UaN
    Moteur: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    tension assignée
    tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
    [IEC 62040-1, ed. 1.0 (2008-06)]

    tension nominale, Un
    tension par laquelle un réseau est désigné ou identifié
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Un

    EN

    FR

    Русско-французский словарь нормативно-технической терминологии > номинальное напряжение

  • 2 номинальное значение

    1. valeur nominale
    2. valeur de dénomination
    3. valeur assignée
    4. caractéristiques assignées

     

    номинальное значение
    Количественное значение, указанное, как правило, изготовителем для определенного рабочего состояния детали, устройства или аппарата.
    МЭК 60050(151-04-03).
    [ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]


    номинальное значение
    Значение величины, установленное обычно изготовителем для определенных рабочих условий компонента, прибора или оборудования.
    [ ГОСТ Р 52319-2005 (МЭК 60050-151 [10], позиция 151-04-03)]

    номинальное значение
    Значение параметра электротехнического изделия (устройства), указанное изготовителем, при котором оно должно работать, являющееся исходным для отсчета отклонений.
    Примечание
    К числу параметров относятся, например, ток, напряжение, мощность.
    [ ГОСТ 18311-80]


    номинальное значение
    -

    [
    IEV number 442-01-01]

    EN

    nominal value
    value of a quantity used to designate and identify a component, device, equipment, or system
    NOTE – The nominal value is generally a rounded value.
    [IEV number 151-16-09]


    rated value
    a quantity value assigned, generally by a manufacturer, for a specified operating condition of a component, device or equipment
    Source: 151-04-03
    [IEV number 442-01-01]

    FR

    valeur nominale, f
    valeur de dénomination, f
    valeur d'une grandeur, utilisée pour dénommer et identifier un composant, un dispositif, un matériel ou un système
    NOTE – La valeur nominale est généralement une valeur arrondie.
    [IEV number 151-16-09]


    valeur assignée
    valeur d'une grandeur fixée, généralement par le constructeur, pour un fonctionnement spécifié d'un composant, d'un dispositif ou d'un matériel
    Source: 151-04-03
    [IEV number 442-01-01]

    Синонимы

    EN

    DE

    FR

    Русско-французский словарь нормативно-технической терминологии > номинальное значение

  • 3 номинальное напряжение изоляции (аппарата), Ui

    1. TIA
    2. tension assignée d'isolement

     

    номинальное напряжение изоляции (аппарата), Ui
    Значение напряжения, по которому определяют испытательное напряжение при испытании изоляционных свойств, расстояние утечки и воздушные зазоры.
    Максимальное значение номинального рабочего напряжения не должно превышать наибольшего значения номинального напряжения изоляции.
    Примечание — Для аппарата, у которого номинальное напряжение изоляции не устанавливается, его следует принимать как наибольшее значение любого номинального напряжения
    [ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]

    EN

    rated insulation voltage, Ui
    value of voltage to which dielectric tests and creepage distances are referred
    [IEC 62314, ed. 1.0 (2006-05)]


    rated insulation voltage (RIV)
    voltage value assigned by the manufacturer to the equipment or to a part of it, characterizing the specified (long-term) withstand capability of its insulation
    NOTE 1 The rated insulation voltage is higher than or equal to the rated voltage of the equipment, or to the rated voltage of the concerned part of the equipment, which is primarily related to functional performance.
    NOTE 2 The rated insulation voltage refers to the insulation between electric circuits, between live parts and exposed conductive parts and within an electric circuit.
    NOTE 3 For clearances and solid insulation, the peak value of the voltage occurring across the insulation or clearance is the determining value for the rated insulation voltage. For creepage distances the r.m.s. value is the determining value
    [IEC 62103, ed. 1.0 (2003-07)]

    FR

    tension assignée d'isolement (TIA)
    valeur efficace de la tension de tenue fixée par le constructeur au matériel ou à une de ses parties, caractérisant la capacité de tenue spécifiée (à long terme) de son isolation
    NOTE 1 La tension assignée d'isolement est supérieure ou égale à la tension assignée du matériel ou de la partie concernée de l’appareil qui est principalement liée aux caractéristiques fonctionnelles.
    NOTE 2 La tension d'isolement assignée se rapporte à l'isolation entre circuits électriques, entre parties conductrices et masses, et à l'intérieur du circuit électrique.
    NOTE 3 Pour les distances d'isolement et pour les isolants solides, la tension d'isolement assignée est déterminée par la valeur de crête de la tension apparaissant aux bornes de l'isolant ou de la distance. Pour les lignes de fuites, c'est la tension efficace qu'il faut prendre
    [IEC 62103, ed. 1.0 (2003-07)]

    Тематики

    EN

    FR

    Русско-французский словарь нормативно-технической терминологии > номинальное напряжение изоляции (аппарата), Ui

  • 4 номинальное напряжение изоляции (соединительного устройства)

    1. tension d'isolement assignée (d'un dispositif de connexion)

     

    напряжение по изоляции
    Напряжение, определяемое изготовителем для данного соединителя и его составных частей, с которыми соотносятся испытания на электрическую прочность изоляции, воздушные зазоры и расстояния утечки.
    [ ГОСТ Р 51323.1-99]

    номинальное напряжение изоляции (соединительного устройства)

    -
    [IEV number 442-06-39]

    EN

    rated insulation voltage, (of a connecting device)
    phase/neutral or phase/phase voltage value assigned to the connecting device by the manufacturer, this device being intended to be used in installations, the voltage supply of which does not exceed the rated insulation voltage of the connecting device itself
    NOTE – Rated insulation voltage is always understood to be between live parts and not between live parts and earth (ground).
    [IEV number 442-06-39]

    FR

    tension d'isolement assignée (d'un dispositif de connexion)
    valeur de la tension phase/neutre ou phase/phase assignée par le constructeur du dispositif de connexion, celui-ci étant prévu pour être utilisé dans des installations dont la tension d'alimentation ne dépasse pas la tension d'isolement assignée du dispositif de connexion lui-même
    NOTE – La tension d'isolement assignée est toujours comprise comme la tension entre parties sous tension et non entre parties sous tension et terre.
    [IEV number 442-06-39]

    Тематики

    EN

    • rated insulation voltage, (of a connecting device)

    DE

    FR

    Русско-французский словарь нормативно-технической терминологии > номинальное напряжение изоляции (соединительного устройства)

  • 5 номинальный дифференциальный рабочий ток

    1. courant assigné différentiel résiduel de fonctionnement

     

    номинальный остаточный дифференциальный рабочий ток
    IΔn

    Аварийный ток, на который рассчитано защитное устройство, управляемое остаточным дифференциальным током.
    [ ГОСТ Р 61557-1-2006]

    EN

    rated residual operating current
    IΔN

    value of residual current assigned by the manufacturer which causes the RCM to operate under specified conditions
    [IEC 61557-11, ed. 1.0 (2009-01)]

    FR

    courant assigné différentiel résiduel de fonctionnement
    IΔN
    valeur du courant différentiel résiduel fixée par le constructeur qui doit faire fonctionner le RCM dans des conditions spécifiées
    [IEC 61557-11, ed. 1.0 (2009-01)]

    Тематики

    EN

    FR

    Русско-французский словарь нормативно-технической терминологии > номинальный дифференциальный рабочий ток

См. также в других словарях:

  • Value Measuring Methodology — (or VMM) is a tool that helps planners balance both tangible and intangible values when making investment decisions, and monitor benefits.Formal methods to calculate the Return on Investment (or ROI) have been widely understood and used for a… …   Wikipedia

  • Value change dump — is an ASCII based format for dumpfiles generated by EDA logic simulation tools. The standard, four value VCD format was defined along with the Verilog hardware description language by the IEEE Standard 1364 1995 in 1995. An Extended VCD format… …   Wikipedia

  • Value noise — is a type of noise commonly used as a procedural texture primitive in computer graphics. It is conceptually different, and often confused with gradient noise examples of which are the Perlin noise and Simplex noise. This method consists of a… …   Wikipedia

  • Value of life — The value of life (or price of life) is an economic or moral value assigned to life in general, or to specific living organisms. In social and political sciences, it is the marginal cost of death prevention in a certain class of circumstances. As …   Wikipedia

  • value — The utility of an object in satisfying, directly or indirectly, the needs or desires of human beings, called by economists value in use, or its worth consisting in the power of purchasing other objects, called value in exchange. Joint Highway… …   Black's law dictionary

  • value + structural law of value —    by David B. Clarke   The term value has currency not only in political economy use value, exchange value, surplus value but also in terms of the great humanist criteria of value, the whole civilisation of moral, aesthetic and practical… …   The Baudrillard dictionary

  • Value (computer science) — In computer science, a value is a sequence of bits that is interpreted according to some data type. It is possible for the same sequence of bits to have different values, depending on the type used to interpret its meaning. For instance, the… …   Wikipedia

  • value — /val yooh/, n., v., valued, valuing. n. 1. relative worth, merit, or importance: the value of a college education; the value of a queen in chess. 2. monetary or material worth, as in commerce or trade: This piece of land has greatly increased in… …   Universalium

  • assigned value — nurodytoji vertė statusas T sritis Standartizacija ir metrologija apibrėžtis Projektavimo, normatyviniuose ar kitokiuose dokumentuose nurodyta tam tikro dydžio vertė. atitikmenys: angl. assigned value; desired value vok. Aufgabewert, m; Sollwert …   Penkiakalbis aiškinamasis metrologijos terminų žodynas

  • assigned value — nurodytoji vertė statusas T sritis fizika atitikmenys: angl. assigned value; desired value vok. Aufgabewert, m; Sollwert, m; Vorgabewert, m rus. заданное значение, n; указанное значение, n pranc. valeur prescrite, f; valeur spécifiée, f …   Fizikos terminų žodynas

  • value — /ˈvælju / (say valyooh) noun 1. that property of a thing because of which it is esteemed, desirable, or useful, or the degree of this property possessed; worth, merit, or importance: the value of education. 2. material or monetary worth, as in… …  

Поделиться ссылкой на выделенное

Прямая ссылка:
Нажмите правой клавишей мыши и выберите «Копировать ссылку»