-
1 transistorihäviöteho
• transistor dissipation -
2 мощность рассеяния транзистора
Electronics: transistor dissipationУниверсальный русско-английский словарь > мощность рассеяния транзистора
-
3 мощность, рассеиваемая транзистором
Makarov: transistor dissipationУниверсальный русско-английский словарь > мощность, рассеиваемая транзистором
-
4 Transistorverlustleistung
Transistorverlustleistung f transistor dissipationDeutsch-Englisch Wörterbuch der Elektrotechnik und Elektronik > Transistorverlustleistung
-
5 импульсный источник электропитания с коммутацией тока на первичной стороне
импульсный источник электропитания с коммутацией тока на первичной стороне
-In primary switch mode power supplies, the AC mains voltage is first rectified and smoothed and then chopped ("switched"). Chopping means that the DC voltage is switched periodically at a frequency of 40 to 200 kHz using a power transistor.
In contrast to linearly regulated power supplies, the power transistor does not act as a variable resistor but as a switch instead. This generates a square-wave AC voltage that is transformed to the secondary circuit using a high-frequency transformer. In the secondary circuit, the voltage is rectifi ed and smoothed. The quantity of energy transformed to the secondary circuit is controlled, depending on the load, by varying the chopping rate. The longer the transistor is conductive, the higher is the quantity of energy transformed to the secondary circuit ( pulse width modulation).
Due to the use of high-frequency AC voltage, primary switch mode power supplies have the decisive advantage that their transformer can be of much smaller size than required for the transformation of low frequencies. This reduces the weight and the dissipation inside the unit. The effi ciency of these units is between 85 and 95 %. Since the output voltage does not directly depend on the input voltage, these units can be used for a wide input voltage range and can even be supplied with DC voltage. Furthermore, it is possible to buffer short-time mains voltage breakdowns up to 200 ms. However, the power failure buffering time is limited by the size of capacitor C1 since a longer buffering time requires a higher capacity and thus a bigger size of the capacitor. Especially in case of small power supplies this is not desirable.
Therefore, a practicable compromise has to be made between the size of the power supply and the buffering time.
Primary switch mode power supplies can be used for all purposes. For example, they are suitable for the supply of all kind of electronics as well as for electromechanical applications.
[ABB]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > импульсный источник электропитания с коммутацией тока на первичной стороне
См. также в других словарях:
Transistor–transistor logic — (TTL) is a class of digital circuits built from bipolar junction transistors (BJT), and resistors. It is called transistor–transistor logic because both the logic gating function (e.g., AND) and the amplifying function are performed by… … Wikipedia
Transistor — For other uses, see Transistor (disambiguation). Assorted discrete transistors. Packages in order from top to bottom: TO 3, TO 126, TO 92, SOT 23 A transistor is a semiconductor device used to amplify and switch electronic signals and power. It… … Wikipedia
Transistor — Quelques modèles de transistors. Le transistor est un composant électronique actif utilisé : Comme interrupteur dans les circuits logiques ; Comme amplificateur de signal ; Pour stabiliser une tension, moduler un signal ainsi que… … Wikipédia en Français
transistor — /tran zis teuhr/, n. 1. Electronics. a semiconductor device that amplifies, oscillates, or switches the flow of current between two terminals by varying the current or voltage between one of the terminals and a third: although much smaller in… … Universalium
Bipolar transistor biasing — Bipolar transistor amplifiers must be properly biased to operate correctly. In circuits made with individual devices (discrete circuits), biasing networks consisting of resistors are commonly employed. Much more elaborate biasing arrangements are … Wikipedia
Avalanche transistor — An Avalanche Transistor is a bipolar junction transistor designed for operation in the region of its collector current/collector to emitter voltage characteristics beyond the collector to emitter breakdown voltage, called avalanche breakdown… … Wikipedia
Resistor–transistor logic — (RTL) is a class of digital circuits built using resistors as the input network and bipolar junction transistors (BJTs) as switching devices. RTL is the earliest class of transistorized digital logic circuit used; other classes include… … Wikipedia
Multiple-emitter transistor — A multiple emitter transistor is a specialized Bipolar transistor mostly used at input of TTL NAND logic gates. Input signals are applied to the emitters. Collector current stops flowing only if all emitters are driven by the Logical high voltage … Wikipedia
Transistors — Transistor Le transistor est le composant électronique actif fondamental en électronique utilisé principalement comme interrupteur commandé et pour l amplification, mais aussi pour stabiliser une tension, moduler un signal ainsi que de nombreuses … Wikipédia en Français
CMOS — For other uses, see CMOS (disambiguation). CMOS inverter (NOT logic gate) Complementary metal–oxide–semiconductor (CMOS) ( … Wikipedia
Current limiting — is the practice in electrical or electronic circuits of imposing an upper limit on the current that may be delivered to a load with the purpose of protecting the circuit generating or transmitting the current from harmful effects due to a short… … Wikipedia