-
81 coordinate
-
82 волновод
м. waveguide -
83 axes
pl. от axis; см. тж. axis -
84 maneuver
маневр; фигура ( пилотажа) ; pl. маневры; маневрировать; выполнять маневрcombined aerodynamic-propulsive orbital plane change maneuver — комбинированный маневр для поворота [изменения] плоскости орбиты с использованием тяги двигателя и аэродинамических сил
lazy-8 maneuver — фигура «ленивая восьмёрка (горизонтальная восьмёрка с попеременными наборами и снижениями при каждом изменении направления на 90°)
zero ground speed maneuver — верт. маневр на месте [при нулевой путевой скорости]
-
85 wing
крыло; авиационное крыло, (авиа)крыло ( организационная единица) ; pl. разг. «крылья» ( нагрудный знак лётного состава) ; летать на самолёте; крыльевой60° wing — крыло с углом стреловидности 60° (по передней кромке)
75 per cent swept delta wing — треугольное крыло с углом стреловидности 75° по передней кромке
85 per cent flapped wing — крыло с закрылками на 85% размаха
cock up the wing — разг. задирать крыло вверх
give drop to a wing — уменьшать подъёмную силу крыла (на одной половине); опускать крыло
mid(-mounted, -set) wing — среднерасположенное крыло
one-sixth scale model wing — модель крыла в масштабе 1:6
shoulder(-height, -mounted) wing — высокорасположенное крыло
— aft wing— air wing— dry wing— fly wing— jet wing— top wing— wet wing— X wing -
86 маршрут
route
- (линия пути) — track
- (линия пути между двумя последующими ппм) — track (between two successive wpts)
- большой протяженности — long-haul service (route)
самолет для полетов на маршрутах большой протяженности. — long-haul service airplane.
-, воздушный — air route
ограниченное воздушное пространство между двумя пунктами полета с навигационным обеспечением. — а defined air space between two points, subject to navigational regulations.
-, заданный (лзп-линия заданного пути) — desired track (dtk, dsrtk)
-, запасный — alternate route
- захода на посадку (отворотом на расчетный угол) — (teardrop) approach pattern
- малой протяженности — short-haul service
- наружного осмотра (самолета) — circuit of external inspection, walk around check
поспедовательность осмотра агрегатов самолета, двигателя и оборудования. (рис. 148) — sequence of external inspections of the aircraft, engine and equipment components.
-, обратный — return route
-, ортодромический — great-circle route
flying on nearly great-circle route.
- отлета outbound — track
- подхода inbound — track
- полета — flight route
выбранный заранее путь самолота, обеспечивающий надежность ориентировки, безопасность полета и точный выход в заданную точку, — preselected track subject to navigational regulations and ensuring flight safety and reaching the point of destination.
- полета — track, course
линия (заданного) пути, пролаженная на карте, — the line on а map or chart along which any aircraft is travelling.
-, прямоугольный посадочный — rectangular approach traffic pattern
- руления — taxi route
- средней протяженности выбирать m. полета — medium-haul service select the flight routeРусско-английский сборник авиационно-технических терминов > маршрут
-
87 approach
1. n1) принцип, метод; технологія2) підхід, підліт (напр. до зони аеродрому)3) заходження [захід] на посадку4) зближення (повітряних суден, космічних апаратів тощо); косм. причалювання5) наближення (напр. до критичних умов польоту)6) метео насування2. v1) наближатися; військ. підступати, зближатися◊to miss approach — відходити на друге коло; неправильно розрахувати заходження на посадку
•- advisory approach - aerocapture approach - aerodrome approach - autocoupled approach - automatic approach - automatic final approach - autonomous approach - back course approach - beacon approach - beam approach - blind approach - center line approach - circling approach - contact approach - continuous descent approach - controlled final approach - conventional approach - co-orbital approach - coupled approach - crosswind approach - curved approach - decelerating approach - direct VOR/DME approach - discontinued approach - docking approach - ecological approach - energy-optimal approach - environmental approach - face-to-face approach - far approach - fault-intolerance approach - fault-tolerance approach - final approach - flat approach - four-impulse approach - front course approach - fuel-optimal approach - gliding approach - ground-controlled approach - hard approach - head-on approach - ICAO category I approach - ICAO category II approach - ICAO category III approach - initial approach - instrument approach - integrated approach - intermediate approach - left-hand approach - localizer approach - long approach - LOS approach - limited visibility approach - low-visibility approach - manned final approach - missed approach - multiburn approach - multi-impulse approach - mutual approach - near approach - ninety-degree approach - no aids used approach - nonprecision approach - nonstraight-in approach - normal approach - off-nominal approach - offset approach - one-eighty approach - optically guided approach - orbiter-to-space station approach - power approach - practice low approach - precision approach - radar approach - radial approach - rectangular traffic pattern approach - right-hand approach - segmented/curved approach - short approach - shortest route approach - simple approach - soft approach - standard approach - steady approach - steep approach - step-by-step approach - step-down approach - straight-in approach - straight-in ILS-type approach - straight missed approach - surveillance radar approach - symmetric thrust approach - teardrop approach - timed approach - two-impulse approach - upwind approach - visual approach - zero-defect approach -
88 дисковая катушечная обмотка
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Русско-английский словарь нормативно-технической терминологии > дисковая катушечная обмотка
-
89 disc type winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disc type winding
-
90 disc winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disc winding
-
91 disk type winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
Англо-русский словарь нормативно-технической терминологии > disk type winding
-
92 disk winding
дисковая катушечная обмотка
Катушечная обмотка, собранная из отдельно намотанных катушек, выполненных в виде плоских спиралей из одного провода или нескольких параллельных проводов
[ ГОСТ 16110-82]Параллельные тексты EN-RU
Aluminum or copper foil disk in high voltage winding.
[ABB]Обмотка высшего напряжения дискового типа из алюминиевой или медной полосы.
[Перевод Интент]
Medium voltage, dry-type transformers may have their high voltage windings constructed using either the layer winding technique or the disc winding technique.
In the disc winding, the required number of turns are wound in a number of horizontal discs spaced along the axial length of the coil. The conductor is usually rectangular in cross-section and the turns are wound in a radial direction, one on top of the other i.e. one turn per layer, until the required number of turns per disc has been wound. The conductor is then moved to the next disc and the process repeated until all turns have been wound. There is an air space, or duct, between each pair of discs. The disc winding requires insulation only on the conductor itself, no additional insulation is required between layers, as in the layer winding.
Disc windingThe disc wound high voltage winding is usually wound in two halves, in order that the required voltage adjustment taps may be positioned at the electrical center of the winding. In this way the magnetic, or effective length of the winding is maintained, irrespective of which tap is used, and therefore the magnetic balance between primary and secondary windings is always close to its optimum. This is essential to maintain the short circuit strength of the winding, and reduces the axial electromagnetic forces which arise when the windings are not perfectly balanced.
Transformer with disc wound coils[Dry-Type disc wound transformers in medium voltage applications. Derek R. Foster I.Eng. MIIE]
Computer aided winding process
Рис. ABB
Тематики
Обобщающие термины
Синонимы
EN
дисковая обмотка
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > disk winding
См. также в других словарях:
space station — space station, adj. an orbiting manned structure that can be used for a variety of purposes, as to assemble or service satellites, refuel spacecraft, etc. Also called space platform. [1940 45] * * * Manned artificial structure designed to revolve … Universalium
Rectangular coordinates — Coordinate Co*[ o]r di*nate, n. 1. A thing of the same rank with another thing; one two or more persons or things of equal rank, authority, or importance. [1913 Webster] It has neither co[ o]rdinate nor analogon; it is absolutely one. Coleridge.… … The Collaborative International Dictionary of English
Space diagonal — In a rectangular box or a magic cube, the four space diagonals are the lines that go from a corner of the box or cube, through the center of the box or cube, to the opposite corner. These lines are also called triagonals or volume diagonals .For… … Wikipedia
Melbourne Rectangular Stadium — AAMI Park redirects here. For the stadium in Adelaide known as AAMI Stadium, see Football Park. AAMI Park AAMI Park … Wikipedia
Vector space — This article is about linear (vector) spaces. For the structure in incidence geometry, see Linear space (geometry). Vector addition and scalar multiplication: a vector v (blue) is added to another vector w (red, upper illustration). Below, w is… … Wikipedia
Scale space implementation — Scale space Scale space axioms Scale space implementation Feature detection Edge detection Blob detection Corner detection … Wikipedia
Monolith (Space Odyssey) — Chaos Computer Club used a model of the 2001 monolith at the Hackers at Large camp site Monoliths are fictional advanced machines built by an unseen extraterrestrial species that appear in Arthur C. Clarke s Space Odyssey series of novels and… … Wikipedia
Flat space — Flat Flat (fl[a^]t), a. [Compar. {Flatter} (fl[a^]t r[ e]r); superl. {Flattest} (fl[a^]t t[e^]st).] [Akin to Icel. flatr, Sw. flat, Dan. flad, OHG. flaz, and AS. flet floor, G. fl[ o]tz stratum, layer.] 1. Having an even and horizontal surface,… … The Collaborative International Dictionary of English
Axes of coordinates in space — Axis Ax is, n.; pl. {Axes}. [L. axis axis, axle. See {Axle}.] A straight line, real or imaginary, passing through a body, on which it revolves, or may be supposed to revolve; a line passing through a body or system around which the parts are… … The Collaborative International Dictionary of English
SYNAGOGUE — This article is arranged according to the following outline. origins and history until the first century first century c.e. middle ages modern period … Encyclopedia of Judaism
Church architecture — The 800 year old Church of Termunterzijl in the north of the Netherlands See also: Architecture of cathedrals and great churches Church architecture refers to the architecture of buildings of Christian churches. It has evolved over the two… … Wikipedia
