-
41 зазор
backlash, ( между валками) bite, chimney, clearance, opening, gap, give, lash, nip, play, slack, slackness, clearance space, space, spacing, split, ( между обсадной колонной и стенкой ствола скважины) standoff, yawn* * *зазо́р м.1. маш. clearanceвыбира́ть зазо́р — take up clearanceпредусма́тривать зазо́р — allow a clearance (between mating or companion parts)2. эл., свар. gapперекрыва́ть зазо́р — jump the gapи́скра перекрыва́ет зазо́р ме́жду электро́дами свечи́ — a spark jumps the gap between the spark-plug points [electrodes]регули́ровать зазо́р конта́ктов прерыва́теля — set the breaker pointsбезопа́сный зазо́р — safety clearanceзазо́р в верши́не разде́лки свар. — root gapвозду́шный зазо́р эл. — air gapзазо́р в подши́пнике — bearing clearanceзазо́р в прерыва́теле ( между контактами системы зажигания) авто — breaker-point gapзазо́р в свече́ зажига́ния ( между электродами свечи) — spark-plug gapрегули́ровать зазо́р в свече́ зажига́ния — set the spark-plug gapзазо́р в соедине́нии свар. — joint gapгаранти́рованный зазо́р ( в системе посадок) — minimum positive allowance, minimum clearanceдиаметра́льный зазо́р — diametral clearanceискрово́й зазо́р — spark gapкольцево́й зазо́р эл. — annular gapкомпенсацио́нный зазо́р — expansion clearanceконта́ктный зазо́р эл. — contact gapлопа́точный, осево́й зазо́р ( в турбине) — impeller clearanceлопа́точный, радиа́льный зазо́р ( в турбине) — peripheral clearanceмеждувенцо́вый зазо́р — rim clearanceзазо́р ме́жду дни́щем по́ршня и пло́скостью голо́вки цили́ндра — piston-to-bead clearanceзазо́р ме́жду по́ршнем и сте́нкой цили́ндра — cylinder clearanceзазо́р ме́жду сте́ржнем кла́пана и толка́телем — tappet clearanceосево́й зазо́р — axial clearanceзазо́р отлипа́ния ( реле) — residual gapпо́люсный зазо́р — pole gapзазо́р при отпу́щенном я́коре ( реле) — released gapзазо́р при притя́нутом я́коре ( реле) — operated gapрабо́чий зазо́р — running clearanceрадиа́льный зазо́р — radial clearanceзазо́р развё́ртки — reamer clearanceзазо́р ре́льсового сты́ка — rail joint gapсбо́рочный зазо́р свар. — fit-up gapтемперату́рный зазо́р — expansion clearanceторцо́вый зазо́р — end clearance* * * -
42 tool
1) инструмент; орудие, орудие производства2) резец; инструмент, режущий инструмент; черновой резец ( зубострогального станка)3) приспособление; оснастка4) pl инструментарий; средства; совокупность инструментов6) налаживать ( станок)•to adjust the tool axially — регулировать инструмент в осевом направлении, смещать инструмент в осевом направлении
- 3D modeling toolsto tool roughly — начерно обрабатывать, грубо обрабатывать
- abrading tool
- abrasive tool
- AC-assisted machine tool
- activated tool
- adapter tool
- adjusting tool
- AI tools
- AI-based modeling tools
- air tool
- alternate tool
- analysis tool
- angle head tool
- angle portable tool
- angled tool
- angle-drilling tool
- annular broaching tool
- antivibration jumper installing tool
- application tools
- arm tool
- assembly tool
- assigned tool
- auxiliary tool
- backspot-facing tool
- backup tool
- back-working tool
- bad tool
- ball nose end cutting tool
- ball-nosed cutting tool
- band tool
- bending tool
- bent tool
- best tools
- blanking tool
- block tool
- boring tool
- box tool
- brazed tool
- brazed-tip tool
- broach tool
- broaching tool
- broad-nose finishing tool
- broad-nosed finishing tool
- broad-nosed tool
- broad-parting tool
- broad-tool
- BTA tool
- bucking tool
- burnishing tool
- burring tool
- cam-controlled machine tool
- carbide tool
- carbide-faced tool
- carbide-inserted tool
- carbide-tipped tool
- carbon-steel tool
- cartridge-type tool
- caulking tool
- CBN cutting tool
- CBN tool
- cemented carbide tool
- cemented-oxide tool
- center tool
- centering tool
- centering-and-facing tool
- ceramic tool
- chamfering tool
- chasing tool
- chemical vapor deposited tools
- chipped tool
- circular form tool
- circular tool
- clamped-tip tool
- clamping tool
- clipping tool
- CNC tools
- CNC ultra-precision machine tool
- CNC-sharpened tool
- coated tool
- coated-carbide cutting tool
- coining press tool
- collet release tool
- collet tool
- combination internal-external tool
- combination machine tool
- combination tool
- combined tool
- computer-controlled machine tool
- contour form milling tool
- contour milling tool
- contour turning tool
- control tools
- coolant-fed tool
- copy lathe tool
- copying tool
- cordless SPC tool
- core tool
- corrugated tool
- counterboring tool
- counter-rotating tool
- cross-drilling/milling tools
- crossworking tool
- crowning shaving tool
- cubic-boron-nitride cutting tool
- cup tool
- curling press tool
- customized machine tool
- cutoff tool
- cutter tool
- cutting laser tool
- cutting tool with inserted blades
- cutting tool
- cutting-off bit tool
- cutting-off tool
- CVD tools
- dead-end tool
- debugging tools
- deburring tool
- dedicated tool
- deep pocket tool
- design tools
- design verification tools
- development tools
- diagnostics tools
- diamond burnishing tool
- diamond tool
- diamond-coated tool
- diamond-edge tool
- diamond-plated tool
- diamond-turning tool
- digitized tool
- disposable cutting tools
- disposable insert tool
- DNC machine tool
- DNC-supported machine tool
- double-acting deburring tool
- double-diameter tool
- double-index roughing tool
- dressing tool
- drill burnishing tool
- drill tool
- drill/tap tool
- drilling tool
- driven tool
- driving tool
- duplicate tools
- edge tool
- EDM tool
- embossing press tool
- end mill tool
- end tool
- end-cutting tool
- end-working tool
- engraving tool
- erecting tool
- expandable abrading tool
- expanding block boring tool
- expanding block-type boring tool
- external tool
- external turning tool
- face grooving tool
- facing tool
- fastening tool
- feed-out tool
- fillet tool
- filleting tool
- fine boring tool
- finish tool
- finish-cut tool
- finishing tool
- first-selection backup tools
- fixed tool
- flat form tool
- flatted parallel shank tool
- flooded coolant tool
- fluted tool
- fly tool
- follow tools
- form tool
- forming machine tool
- forming tool
- fresh cutting tool
- front endworking tool
- gaged master tool
- ganged tools
- gear cutting tool
- gear tool
- general-purpose machine tool
- generating tool
- gooseneck tool
- grabbing tool
- grinding tool
- gripper tool
- gripping tool
- grooving tool
- hand-guided tool
- hand-held grinding tool
- hand-held tool
- hard pointed tool
- heading tool
- heavy-duty machine tool
- high-positive geometry tool
- high-positive-rake tool
- high-speed machine tool
- high-speed steel tool
- high-speed steel-cutting tool
- high-usage tools
- hold-down tool
- honing tool
- hot-set tool
- ID step tool
- ID tool
- idling tool
- image acquisition tools
- impregnated abrasive tool
- impregnated diamond tool
- inactive tool
- indexable cutting tool
- indexable-insert tool
- indexing machine tool
- infeed slide tool
- injection tool
- in-line powered tool
- insert tool
- inserted blade-type tool
- inserted carbide tool
- inserted tip tool
- insertion tool
- inside corner tool
- inside recessing tool
- inside turning tool
- inspection tool
- installation tool
- integrated tools
- integration tools
- interactive design tools
- internal boring tool
- internal diameter tool
- internally operating tool
- inward flanging press tool
- ironing press tool
- irradiated tool
- knowledge engineering tools
- knurling tool
- lab-quality inspection tool
- lancing press tool
- lapping tool
- large hybrid system building tools
- large narrow system building tools
- laser alignment tools
- laser leveling tool
- laser tool
- lathe tool
- layout tool
- left-hand tool
- leveling tool
- LH tool
- life-expired tool
- linear mounted tool
- locating tool
- logic-synthesis tools
- machine tool
- machining tool
- manually adjustable tool
- marking tool
- master tool
- measuring tool
- metal-cutting tool
- metalforming machine tool
- microsizing tool
- migrating tool
- milling tool
- miniCNC machine tool
- misplaced tool
- mis-set tool
- modeling tools
- modular tool
- mold tool
- molding tool
- monocrystalline diamond tool
- multicavity molding tool
- multifaceted tool
- multifluted tool
- multigrooving tool
- multiimpression injection tool
- multiple blanking tool
- multiple insert tool
- multiple-cavity mold tool
- multiple-impression press tool
- multipoint tool
- multipoint-cutting tool
- multitoothed tool
- narrow system building tools
- NC machine tool
- NC tool
- negative-rake cutting tool
- noncutting machine tool
- nonrotating tool
- notching press tool
- odd-fluted cutting tool
- OD-turning tool
- OD-working tool
- offset tool
- oil hole tool
- old tool
- one-sensor-one tool
- operating tool
- order-related tool
- outward flanging press tool
- pallet tools
- parallel-shank tool
- parallel-shanked tool
- particle-type dressing tool
- parting press tool
- parting tool
- part-off tool
- PCD tool
- percussive tool
- perishable tool
- physicochemical machine tool
- pickup tool
- piercing tool
- placement tool
- planer tool
- planing tool
- platen-mounted tool
- pneumatic tool
- polishing machine tool
- polycrystalline CBN cutting tool
- polycrystalline-diamond-edge tool
- polycrystalline-diamond-tipped tool
- polygon tool
- polygonal tool
- portable air tool
- portable expanding tool
- portable pneumatic tool
- portable power tool
- portable sinking tool
- portable tool
- positive/negative tool
- positive/positive tool
- positive-rake cutting tool
- positive-rake tool
- power tools
- powered rotary tool
- powered tool
- power-positioned tool
- preadjusted tool
- preformed boring tool
- preset qualified tool
- preset tool
- presettable tool
- press tool
- prismatic tool
- probe tool
- process tool
- processing tool
- production machine tool
- profiling tool
- programming tools
- protuberance tool
- punching press tool
- qualified tool
- quick-change tools
- rack-type tool
- radial cutting tool
- radioactive tool
- random tool
- rapid change tool
- rapidly wearing tool
- rear endworking tool
- rebuilt machine tool
- recessing tool
- reciprocating gear cutting tool
- reconditioned tool
- refurbished tool
- replaceable-insert tool
- replacement tool
- retrofitted machine tool
- RH tool
- right-angled powered tool
- right-hand tool
- rivet shaving tool
- roller-burnishing tool
- roll-forming tool
- rolling-in tool
- rotary pneumatic tool
- rotary tool
- rotating tool
- rotating turret tool
- rough boring tool
- rough cut tool
- roughing tool
- rough-turning tool
- round tool
- rounded tool
- round-nose tool
- round-nosed tool
- router tool
- routing tool
- scraping tool
- screw-cutting tool
- screw-rolling tool
- second selection backup tools
- segmented bulging press tool
- self-correcting tool
- shank tool
- shankless cutting tool
- shaped tool
- shaper-cutting tool
- shaping tool
- shared tools
- shaving press tool
- shaving tool
- shear tool
- short chipping tool
- side cutting tool
- side tool
- silicon nitride cutting tools
- silicon nitride tool
- simulation tools
- single-crystal tool
- single-layer tool
- single-pass tool
- single-point threading tool
- single-point tool
- single-purpose machine tool
- single-tip tool
- sister tool
- slitting tool
- slotting tool
- smoothing roller tool
- software development tools
- software tools
- software-based integration tools
- solid bit tool
- solid carbide tool
- solid modeling tools
- solid tool
- SPC tool
- specialized machine tool
- specially outfitted machine tool
- spent tool
- spindle probe tool
- spinning tool
- spline drive tool
- split bulging press tool
- spot-facing tool
- spotting tool
- square cutting tool
- square thread tool
- stamping tool
- static tool
- stationary tool
- step tool
- straight portable tool
- straight shank tool
- straight tool
- straight turning tool
- stripping tool
- stub boring tool
- superabrasive-plated tool
- support tools
- surfacing tool
- swan-neck tool
- sweep tool
- sweeping tool
- tail-end tools
- taper shank tool
- tapered shank tool
- tapping tool
- taught tool
- testing tools
- thermal tool
- thread milling tool
- thread turning tool
- thread-cutting tool
- threaded shank tool
- threading tool
- thread-rolling tool
- throwaway carbide tool
- throwaway insert tool
- throwaway tip tool
- throwaway tool
- tipped tool
- titanium-carbide-coated tool
- to tool up
- touch sensitive tool
- transfer tool
- transparent tool
- trepanning tool
- triangular cutting tool
- trim tool
- truing tool
- tube-expanding tool
- Tunruf tool
- turning tool
- turret tool
- ultrasonic tool
- undercutting tool
- underrun tool
- underused tool
- underutilized tool
- undetected broken tool
- unit-type machine tool
- universal boring and thread milling tool
- unmanned machine tool
- untended CNC machine tool
- versatile machine tool
- vibrating tool
- viscous damped tool
- visualization tools
- V-thread tool
- wear-prone tool
- welding laser tool
- wide-finishing tool
- wire-forming tool
- wireless measuring tool
- wobble broach tool
- wood-cutting tool
- workplace tool
- worm-configured tool
- worn cutting tool
- X-axis tool
- Y-axis tool
- Z-axis toolEnglish-Russian dictionary of mechanical engineering and automation > tool
-
43 tooling
1) технологическая оснастка; инструментальная оснастка2) инструменты, режущие инструменты•- 50-taper toolingtooling up — оснащение ( станка) инструментами и приспособлениями
- angle-head tooling
- ANSI vee tooling
- assembly tooling
- automatic size control tooling
- back tooling
- backup tooling
- blazed carbon tipped tooling
- block tooling
- block-style tooling
- built-up tooling
- carbide inserted tooling
- carbide-tipped tooling
- ceramic tipped tooling
- chip removal tooling
- cluster tooling
- CNC tooling
- coated tooling
- combination tooling
- custom tooling
- dedicated tooling
- deep hole tooling
- delicate tooling
- diamond tooling
- die tooling
- double D tooling
- driven tooling
- durable tooling
- end-of-arm tooling
- fast-change tooling
- fast-indexing tooling
- ganged tooling
- gang-type tooling
- high-speed carbide tooling
- indexable-insert tooling
- insert tooling
- ISO 50 tooling
- ISO tooling
- linear tooling
- live tooling
- long-taper tooling
- machine tooling
- machining-center-type tooling
- master tooling
- modular component tooling
- modular tooling
- multigrip tooling
- multihead tooling
- multiple tooling
- off-the-shelf tooling
- one-piece tooling
- palletized tooling
- parallel shank tooling
- part family tooling
- part-separation tooling
- PCD tooling
- peripheral tooling
- perishable tooling
- permanent-set tooling
- power-driven tooling
- powered tooling
- preset tooling
- presettable tooling
- production tooling
- quick-change tooling
- radial tooling
- redundant tooling
- robot tooling
- rotary tooling
- set tooling
- short-taper tooling
- single D tooling
- single-point tooling
- sister tooling
- snap-change tooling
- solid carbide tooling
- spindle tooling
- split-design tooling
- static tooling
- straight-shank tooling
- support tooling
- templet tooling
- through-coolant tooling
- throwaway tooling
- top tooling
- triangular-shank tooling
- tungsten carbide tooling
- turret tooling
- V-flange tooling
- workpiece support toolingEnglish-Russian dictionary of mechanical engineering and automation > tooling
-
44 axle
ось; полуось; вал; мост; ведущий мост; поперечная балка моста; шпиндель; валик- axle and wheel aligner - axle arm - axle arrangement - axle attachment to spring - axle assembly - axle base - axle beam - axle bearing - axle bearing puller - axle bed - axle body - axle box - axle cap - axle cap bolt - axle cap filler cover - axle casing - axle centering - axle clearance - axle compartment - axle configuration - axle design weight - axle drive - axle drive gear - axle drive bevel gear - axle drive bevel pinion - axle drive bevel wheel - axle drive pinion - axle drive pinion carrier - axle drive shaft - axle driven gear - axle end - axle fore-and-aft shake - axle fracture - axle grease - axle-ground clearance - axle housing - axle-hung - axle input - axle journal - axle journal collar - axle load - axle load indicator - axle-load distribution - axle-load sensor - axle-load transfer - axle lubricant - axle-mounted disk brake - axle neck - axle noise - axle nut - axle nut washer - axle pad - axle packing - axle pin - axle press - axle puller - axle pulling bushing - axle run-out - axle rating - axle ratio - axle seat - axle shaft - axle shaft extractor - axle shaft gear - axle shaft housing - axle shaft oil seal - axle side shake - axle sleeve - axle spacing - axle spindle - axle stand - axle straightener - axle straightening iron - axle straightening tool set - axle suspension - axle suspension steering linkage - axle swivel - axle tools - axle-tree - axle tube - axle weight - axle weight limit - axle windup - axle yaw- air axle- bearing axle - bent axle - brake axle - brake lever axle - breaker lever axle - cambered axle - cambered live axle - car axle - cardan axle - carrying axle - chain pinion axle - channel-section axle - conventional axle - core axle - coupling axle - crank axle - cranked axle - dead axle - differential axle - divided axle - double-joint rear axle - drilling bit leg axle - driving axle - drop axle - dual-performance rear axle - Elliot axle - end axle - fixed axle - flared tubular axle - flexible axle - floating axle - fore axle - foremost axle - forked axle - forward rear axle - free axle - free steering axle - front axle - full floating axle - guiding axle - half-axle - hollow axle - I-beam axle - intermediate axle - internal-geared axle - leading axle - light-duty axle - live axle - loose axle - medium-duty axle - mounted axle - movable axle - oscillating axle - pivot axle - pivoted axle - pony axle - radial axle - radius rod controlled axle - rear axle - rear-rear axle - rearmost axle - reverse Elliot axle - rigid axle - rotating axle - semi-axle - semifloating axle - semifloating rear axle - set-back front axle - shaft axle - shifting axle - solid axle - sowing axle - stationary axle - steering axle - steering clutch release crank axle - straight axle - stub axle - supporting axle - swing axle - tandem axles - three-quarter floating axle - trailing axle - tubular axle - two-speed axle - universally jointed axle - withdrawable back axle - or rear axle - wheel axle -
45 approach
1. n приближение; приход, наступлениеat our approach — при нашем приближении, когда мы подошли
2. n воен. подступ; подход; сближение3. n обыкн. l4. n подступы5. n дор. подъезд, подъездной путь6. n авансы, подходыto make approaches to a girl — ухаживать за девушкой; заигрывать с девушкой
engineering approach — инженерный подход; инеженерный метод
7. n тех. подача, подвод8. n метеор. надвижение9. n спорт. разбег10. n косм. сближениеcollision approach — сближение, угрожающее столкновением
11. n спорт. выводящий удар12. v подходить, приближаться13. v близиться14. v воен. подступать, сближаться15. v воен. сближать16. v граничить, приближаться17. v обращаться; вступать в переговорыall-or-nothing approach — принцип "всё или ничего"
18. v разг. подъезжать, подкатыватьсяhave you approached the manager about a raise? — ты не пробовал подъехать к заведующему относительно прибавки?
19. v ухаживать, пытаться соблазнитьСинонимический ряд:1. access (noun) access; entrance; passageway2. advances (noun) advance; advances; overture3. coming (noun) advent; coming; convergence; imminence; nearness4. course (noun) attack; course; line; plan; procedure; tack5. method (noun) method; strategy; tactic; technique6. access (verb) access; converge; intersect; join7. accost (verb) accost; confront; solicit8. address (verb) address; apply to; bespeak; memorialize9. amount (verb) amount; correspond to; equal; match; partake of; touch10. apply (verb) appeal; apply; petition; sound; sue11. approximate (verb) approximate; compare; nigh; resemble; rival; verge on12. be imminent (verb) be forthcoming; be imminent; be on the horizon; come closer; draw near; draw nigh; impend; loom up13. border (verb) border; trench; verge14. catch (verb) catch; overtake15. go toward (verb) advance; gain on; go toward; near; surround; verge upon16. open (verb) begin; commence; embark; enter; inaugurate; initiate; launch; open; set out; set to; start; take on; take up; undertake17. propose (verb) appeal to; encounter; propose; request; waylay18. reach (verb) reachАнтонимический ряд:avoid; departure; differ from; disparity; distance; diversity; egress; exit; leave; lose; outlet; recession; retreat -
46 зазор
1. м. маш. clearance2. м. эл. свар., gap -
47 счетчик ампер-часов,
integrating amper-hour counter
интегрирующий (иса)
- аэрофотоснимков — exposure counter
-, барабанный — drum counter
- барометрический высоты (высотомера) — barometric altitude counter
- барометрической высоты аэродрома (ро) — ground pressure counter
кремальера на лицевой панели высотомера служит для установки счетчика высоты аэродрома и ввода соответствующей поправки в работу механизма высотомера. — the knob protruding from the altimeter is used to set a ground pressure counter and to apply appropriate correction to the altimeter mechanism.
- ввода начальных данных (инерциальной навигационной системы) — data display (of ins control display unit)
- времени (наработки прибора) — (elapsed) time counter
- (- сигнализатор) высоты (высотомера) — altitude /height/ counter
- дальности — dme counter, distance display counter, dme readout
цифровой указатель наклонной дальности до маяка радиодальномера на плановом навигационном приборе (рис. 73). — а digital readout of dme slant range (in nautical miles or kilometers) is given by the readout in the upper left corner of the course indicator.
- десятков — decade counter
- единиц — digit counter
- заданного путевого угла (зпу) — (selected) course (display) counter /readout/
цифровой указатель курсового луча (зпу) станции vor или курсового радиомаяка (крм) на плановом навигационном приборе (рис. 73). — the course counter in the upper right corner of the course indicator improves the accuracy and speed of course selection by giving a digital readout of the vor radial or localizer course indicated by the course arrow.
- координат (доплеровский) — coordinate indicator
- магнитной ленты, цифровой — digital tape counter
- наработки (блока, прибора) — (elapsed) time counter /indicator/, time totalizing meter
- наработки и числа запусков (двиг., апу) — elapsed time and starting counter /indicator/
- наработки режимов (работы двигателя, снр) — engine power /thrust/ setting time counter
- наработки (блока), цифровой — digital time totalizing meter
- (остатка) патронов — rounds counter
- остатка топлива (суммарного расхода) — fuel remaining counter
- пройденного пути — (air) distance flown counter /indicator/
shows continuously and automatically the air distance flown.
- пройденного пути (в милях) — air-mileage indicator
- расстояния (пути), пройденного ла (пяти-цифровой с пределом измерения до 99,999 км) — (five-digit) distance flown counter (reading up to 99.999 km)
- суммарного расхода топлива (указателя расходомера) — total fuel consumed counter
датчик расходомера выдает электрический сигнал, пропорциональный расходу топлива (в кг/час). суммарный расход топлива указывается счетчиками (рис. 74). — the fuel flow transmitter produces an electric signal which is proportional to fuel flow in pounds per hour (or kg per hour). the total fuel consumed is indicated by counters.
- текущих координат — present-position counter
- (-) указатель дальности полета — distance flown counter
- (пяти-) цифровой вводить (к-л. величину) на счетчике — (five-) digit counter enter /set/ (data) to be displayed on /on/ counterРусско-английский сборник авиационно-технических терминов > счетчик ампер-часов,
-
48 угол (геометрический)
angle
- (кабины, панели) — corner
указатель установлен в верхнeм левом углу приборной доски. — the indicator is located on the upper left corner of the instrument panel.
- (при определении географических и навигационных параметров) — angle, angular distance
- (эл. сигнал, соответствующий угловой величине) — angular information the angular information is supplied to the stator windinq.
- азимута (e) — azimuth
-, азимутальный (в полярных координатах) — azimuth angle
угловая величина, отсчитываемая по часовой или против часовой стрелки от северного или южного направления от о град, до 90 или 180 град. — measured from 0о at the north or south reference direction clockwise or counterclockwise through 90о or 180о.
-, азимутальный (курс) — azimuth
- азимутальный (гироппатфор'мы), отсчитываемый от местного географического меридиана — stable platform azimuth angle measured from local geographic meridian
- азимутальный, направленно' гo луча антенны — azimuth angle of antenna beams
- атаки (а) — angle of attack (alpha, aat)
угол, заключенный между линией отсчета, жестко связанной с планером (крылом) самолета и направлением движения ла. — the angle between a referелее line fixed with respect to an airframe and a lipe in the direction of the aircraft.
лампа сигнализации выключенного обогрева автомата угпа атаки. (ауасп обогр. выкл.) — alpha off light
- атаки (англ. термин) — angle of incidence (british usage)
- атаки, индуктивный — induced angle of attack
составная часть любого текущего угла атаки, превышающая эффективный угол атаки. — а part of any given angle of attack over and above the effective angle of attack.
- атаки крыла (профиля) — wing angle оf attack
угол, заключенный между хордой профиля и направлением набегающего потока воздуха (рис.135). — the angle between the chord line of the wing (airfoil) and the relative airflow.
- атаки, большой — high angle of attack
- атаки, вызывающий срабатывание системы предотвращения сваливания (выхода на критический угол атаки) — stall barrier actuation angle of attack. the system suppresses the stall warning and barrier асtuation angles of attack to prevent stall overshoot.
- атаки, докритический — pre-stall(ing) angle of attack
- атаки, закритический — angle of attack beyond stall
- атаки, критический, — angle of sfall, stalling angle, stall
угол атаки, соответствующий максимальному значению коэффициента подъемной силы. — the angle of attack correspending to the maximum lift coefficient.
- атаки, местный — local angle of attack
- атаки нулевой подъемной силы — zero lift angle of attack
- атаки, отрицательный — negative angle of attack
- атаки, положительный — positive angle of attack
- атаки, средний — medium angle of attack
- атаки, текущий (a тем) — present angle of attack
- атаки, эффективный — effective angle of attack
-, боевой магнитный путевой (бмпу) — run-in magnetic track angle /course/
- бокового скольжения — angle of sideslip
- ветра (ув) — wind angle (u)
угол, заключенный между вектором путевой скорости и вектором ветра (рис. 124). — the angle between the true course and the direction from which the wind is blowing, measured from the true course toward the right or left, from 0 to 180°.
- ветра, курсовой — wind angle
- взмаха — flapping angle
острый угол, образованный продольной осью лопасти неcyщeгo винта вертолета и плоскостью вращения втулки винта при повороте лопасти относительно горизонтальногo шарнира. — the difference between the coning angle and the instantaneous angle of the span axis of a blade of a rotary wing system relative to the plane perpendicular to the axis of rotation.
- видимости аэронавигационного огня (ано) (рис. 97) — navigation light dihedral angle
- видимости левого ано (угол "л") — navigation light dihedral angle l (left)
- видимости правого ано (угол "п") — navigation light dihedral angle r (riqht)
- видимости хвостового ано (угол "x") — navigation light dihedral angle a (aft)
- визирования — sight angle, angle of sight
- возвышения — angle of elevation, elevation
угол в вертикальной плоскости между горизонталью и наклонной линией от наблюдателя до объекта (рис. 129). — the angle in a vertical plane between the local horizontal and ascending line, as from an observer to an object.
- волнового конуса — mach angle
the angle between a mach line and the direction of movement of undisturbed flow.
- вращения — angle of rotation
- выставки телеблока — telescope /telescopic/ - sensor alignment angle
- гироппатформы, азимутапьный (инерциальной системы) — stable platform azimuth
- глиссады — glide slope angle
угол в вертикальной плоскости между глиссадой и горизонталью (рис. 120). — angle in vertical plane between the glide slope and the horizontal.
-, гринвичский часовой — greenwich hour angle (gha)
угол к западу от астрономического гринвичского меридиана. — angular distance west of the greenwich celestial meridian.
- датчика (угла) гироскопа — gyro-pickoff angle
-, двугранный (ано) — dihedral angle
- действия (см. видимости) — navigation light dihedral angle
-, заданный путевой (зпу) (рис. 124) — desired track angle (dsrtk) (dtk)
- заклинения (установки несущей поверхности) — angle of setting, rigging angle of incidence
фиксированный угол между плоскостью хорды крыла (стабилизатора) и продольной осью самолета (осью тяги) при горизонтальном положении самолета (рис. 135). — а fixed angle between the plane of the wing chord and the line of thrust or any other longitudinal line which is level when the fuselage is level longitudinally.
- заклинения горизонтального оперения — angle of stabilizer setting
острый угоп между продольной осью самолета и хордой (горизонтального) стабилизатора. угол является положительным при превышении передней кромки стабилизатора над задней. — the acute angle between the line of thrust of an airplane and the chord of the stabillzer. the angle is positive when the leading edge is higher than the trailing edge.
- заклинения крыла — angle of wing setting
острый угол между плоскостью хорды крыла и продольной осью самолета. угол является положительным при превышении передней кромки крыла над задней. — the acute angle between the plane of the wing chord and the longitudinal axis of the airplane. the angle is positive when the leading edge is higher than the trailing edge.
- заклинения крыла у корня — angle of wing setting at root
- заклинения крыльев (биплана) — decalaqe
разность между углами установки верхнего и нижнего крыльев. острый угол между линиями хорд крыльев в плоскости, параллельной плоскости симметрии самолета. — a difference in the angles of setting of the wings of a biplane. the decalage is measured by the acute angle between tfle chords in a plane parallel to the plane of symmetry.
- застоя (картушки компаса) — angular friction error (of compass card)
- затенения (огня), телесный — solid angle of obstructed (light) visibility
- зрения — angle of view
-, исходный путевой — initial departure track angle
- кабины — corner ot cabin
- карты — drivation
the angle between the grid datum and the magnetic meridian.
- карты (в автоматическом навигационном планшете) — map /chart/ angle (ca)
задатчик ук устанавливается на заданный пеленг в каждой точке разворота. если дм (магн, склонение) = +8о то ум = 352о, если дм = -5о, то ук = 5о ук = мпу главной ортодромии — the map or chart angle selector is set to the appropriate bearing at each turning point.
- конусности (лопасти несущего винта) — coning angle
угол между продольной осью лопасти и плоскостью круга ометаемого законцовкой винта. — the angle between the longitudinal axis of а blade and the tip-path plane.
- крена (у) — angle of roll, bank (angle)
угол между поперечной осью самолета и горизонтальной плоскостью. угол считается положительным при правом крене (рис. 135). — the angle between the lateral axis and a horizontal plane. the angle of roll is considered positive if the roll is to starboard.
- крена, командный — commanded bank angle
- крена при (для) выходе (выхода) на заданный курс — roll steering bank angle (for smooth roll out on the selected heading)
- крена, текущий — present angle of roll, present bank
- крыла, установочный (рис. 135). — angle of wing setting
- курса (путевой угол) — track angle
- курса (самолета, ч) — heading (ч)
- курса (инерциальной системы) — azimuth
- курсовой (кур) — relative bearing (rb)
автоматический радиокомnac определяет курсовой угол радиостанции, а в сочетанин с компасом или курсовой системой - пеленг радиостанции, как сумму курса и курсового угла (рис. 127). — angle measurement in navigation, measured from the heading of an aircraft, as relative bearing.
-, курсовой (на экране рлс) — azimuth (relative to aircraft)
the indicator display shows targets in terms of range and azimuth relative to aircraft.
- лопасти (возд. винта) — blade angle
угол между нижней поверхностью части лопасти винта и плоскостью вращения, — the angle between the lower surface of an element of a propeller and plane of rotation.
- маневра (курс, крен, тангаж) — attitude change angle
- маха — mach angle
-, местный часовой — local hour angle (lha)
- набора высоты — angle of climb
угол между линией траектории полета набирающего высоту ла и горизонталью. — the angle between the flight path оf а climbing aircraft and local horizontal.
- наведения антенны (радиоастрономическсго корректора) — antenna pointing angle
- наведения астрокорректора — star tracker pointing angle
inertial navigation system provides an accurate azimuth and vertical reference for measurement of the star tracker pointing angles.
- наведения астротелескопа (телеблока) — star-telescope pointing angle
- наклона (подвижных элементов. напр., автомата перекоса) — tilt angle
- наклона скачка уплотнения — shock wave angle
- наклона траектории полета — flight path angle
угол между горизонталью и касательной к данной точке траектории. — the angle between the horizontal and а tangent to the flightpath at a point.
- "ножниц" (рассогласования) закрылков — flaps asymmetry /disagreement/ angle
- "ножниц" (рассогласования) стабилизатора — 'stabilizer (halves) asymmetry /disagreement/ angle
- образованный с... (между) — angle formed with... (between)
- обратной стреловидности (крыла) — sweepforward angle
- опережения зажигания — ignition advance angle
- ортодромии, путевой (пуо) — great circle track angle
- отворота, расчетный (при заходе на посадку) — estimated turn angle (eta)
- отклонения (от направления) — angle of deviation
- отклонения (поверхности управления) — angle of deflection, (control surface) angle
- отклонения закрылка (закрылков) — flap setting
- отклонения закрылков, взлетный — flap takeoff setting
- отклонения закрылков для захода на посадку — flap approach setting
- отклонения закрылков, посадочный — flap landing setting
- отклонения поверхности управления — control surface angle
угол между хордой поверхности управления и хордой несущей (или стабилизирующей) поверхности (крыло, киль, стабилизатор). — control surface angle is an angle between the chord of control surface and the chord of the corresponding fixed surface.
- отклонения руля высоты — elevator angle
- отклонения руля направления — rudder angle
- отклонения ручки (управления) — control stick displacement /deflection/ angle
- отклонения скачка уплотнения — shock wave deflection angle
- отклонения (переставного) стабилизатора — horizontal stabilizer (adjustable) setting
- отклонения элерона — aileron angle
- отрицательной стреловидности — sweepforward angle
- отсека — corner of compartment
- отсчета радиокомпаса (орк) — indicated /observed/ bearing (of radio station)
угол разворота рамочной антенны, отличающийся от курсового угла радиостанции (кур) в результате искажения общего электромагнитного поля металлическими частями самолета (т.е. наличием радиодевиации) (рис. 86). — bearing correction is true radio bearing minus indicated (or observed) radio bearing. plot bearing corrections against observed radio bearings.
-, отсчитываемый от... — angle measured from...
-, отсчитываемый (по часавой стрелке) от северного направления географическоro меридиана — angle measured (clockwise) from north reference direction of geographical meridian.
- пересечения курса (луча на маяк) — (localizer) course /radial/ intersection angle
- пикирования — angle of dive
- планирования — gliding angle
угол между горизонтом и глиссадой самолета (рис. 135). — the angle between the horizontal and the glide path of an aircraft.
- (гиро) платформы, азимутальный — platform azimuth
- поворота вала — shaft angle
- поворота переднего колеса (колес) — nose wheel steering angle
система управления передним колесом шасси обеспечивает угол поворота колec(a) ё45о. — the steering system gives the nose wheel steering angles up to plus or minus 45 deg.
- поворота рамы (гироскопа) — rotation angle (of gimbal)
the rotation angle of the gimbal about the output axis.
-, подаваемый на индикацию (прибор, счетчик) — angular information supplied to be displayed on (indicator, counter, etc.)
- положения — position angle
- поперечного "v", отрицательный (рис. 136) — anhedral (angle)
- поперечного "v" по линии носков, положительный (по передней кромке) — dihedral at leading edge (le)
- поперечного "v", положительный — dihedral angle
острый угол между перпендикуляром к плоскости симметрии самолета и продольной осью крыла в плоскости, перпендикулярной продольной оси самолета (рис. 136). — the acute angle between а line perpendicular to the plane of symmetry and the projection of the wing axis on а plane perpendicular to the longitudinal axis of the airplane.
- поправки на ветер — wind correction angle (wca)
the stronger the wind, the greater the wca.
-, посадочный (самолета) — landing angle
- прицеливания — sighting /aiming/ angle
- проема (напр., аварийного выхода) — opening corner
-, промежуточный (шага винта) — (normal) flight low pitch (angle)
- пространственного положения (ла) — attitude angle
- путевой (пу) — track angle (тк), course angle) (crs)
угол, заключенный между северным направлением меридиана и вектором путевой скорости (линии пути), т.е. направлением движения самолета относительно земной поверхности (рис.124). — а direction of intended movement given as an angle from some reference direction, ordinarily given as a measurement clockwise from the true north or the magnetic north in degrees.
-, путевой, боевой (бпу) — run-in /attack/ track angle
-, путевой, боевой, магнитный (бмпу) — magnetic run-in /attack/ track angle
-, путевой, заданный (зпу) (рис.124) — desired track angle (dsrtk, dtk)
-, путевой, заданный магнитный (змпу) — desired magnetic track angle (dsrmtk, dmtk)
-, путевой истинный (рис.124). — true track angle, true track, true tk
-, путевой, исходный — initial departure track angle
-, путевой магнитный (мну) — magnetic track angle (mtk)
-, путевой, ортодромии (пуо) — great circle track angle
отсчитывается от сев. направления географического меридиана через точку мс до положения направления оси у по часовой стрелке.
-, путевой, при безветрии (при нулевом ветре) — zero-wind track angle
-, путевой, текущий (тпу) — present track angle
-, путевой, условный (рис.124). — grid track angle, grid track, rid tk
-, путевой, фактический — (actual) track angle (tk)
-, путевой, фактический магнитный (фмпу) — actual magnetic track angle
-, путевой, штилевой — zero wind track angle
- радиостанции, курсовой (кур) — relative bearing of radio station (rb)
угол между направлением продольной оси самолета и направлением на наземную радиостанцию, отсчитывается по часовой стрелке от о до 360 град (рис. 127). — the bearing of a radio station or object relative to the heading of an airplane.
- разворота — angle of turn
- разворота переднего колеса (колес) — nose wheel steering angle
- распыла (топлива в форсунке) — (fuel) spray pattern
- рассогласования — error angle
- рассогласования закрылков — flaps asymmetry /disagreement/ angle
- рассогласования по крену (курсу, тангажу) (в сельсинной передаче) — bank (azimuth, pitch) synchro error angle
- рассогласования предкрылков — (le) slats disagreement /asymmetry/ angle
- рыскания (ч) — angle of yaw
угол между продольной осью самолета и заданным направлением полета. угол считается положительным, если передний конец продольной оси самолета отклоняется вправо (рис.135). — the angle, as seen from above, between the longitudinal axis of an aircraft and a chosen reference direction. this angle is positive when the forward part of the longitudinal axis is directed to starboard.
- сближения (схождения) меридианов — earth convergency angle
- свеса (лопасти несущего винта) — droop angle
- скоса потока вверх — angle of upwash
- скоса потока вниз — angle of downwash
- снижения — angle of descent
угол между направлением траектории снижающегося самолета и горизонтом, — the angle between the flight path of a descending aircraft and the local horizontal.
- сноса (ус) — drift angle (da)
угол, заключенный между вектором воздушной скорости и вектором путевой скорости. если впс располагается правее ввс, углу сноса приписывается (+), если левee, тo (-) (рис. 124). — the horizontal angle between the longitudinal axis of an aircraft and its path relative to the ground, i.e. any angular difference existing between the heading and course (or track).
- сноса от измерителя дисс (доплеровского измерителя сноса и путевой скорости) — doppler drift angle (dad)
- солнца, гринвичский часовой — greenwich hour angle of sun (sun gha)
- срабатывания сигнализации — warning aetuation angle
- срабатывания сигнализации критического угла атаки — warning actuation angle of stall
- срабатывания системы предупреждения выхода на критический угол атаки — stall barrier actuation angle
- срыва ламинарного потока — burble point /angle/
а point reached in an increasing angle of attack at which burble begins.
-, стояночный. угол наклона продольной оси самолета относительно плоскости касания колес основного шасси и переднего (хвостового) колеса. — static ground angle (in pitch and bank)
- стреловидности — sweep angle
угол в плоскости крыла между линией, проходящей по размаху крыла (по четвертям хорд, передней или задней кромке) и перпендикуляром к плоскости симметрии самолета (рис. 8). — sweep is an angle in plan between the specified spanwise line (quarter-chord, le, те) along the aerofoil and the normal to the plane of the aircraft symmetry.
- стреловидности (отрицательный) — sweepforward angle
- стреловидности (прямой или положительный) — sweepback angle
- стреловидности по линии четвертей хорд — sweepback (angle) at quarterchord line /at 25 percent of chord/
- стреловидности по передней кромке — sweepback (angle) at leading edge, sweepback at le
- схождения меридианов угол между меридианом точки и вертикальной координатной линией. — earth /meridian/ convergence angle
- тангажа (v) — angle of pitch (v)
угол в вертикальной плоскости между продольной осью самолета и горизонтальной плоскостью. угол считается положительным при наклоне передней части продольной оси вверх (рис.135). — the angle, as seen from the side, between the longitudinal axis of an aircraft and a chosen reference line or plane, usually the horizontal plane. this angle is positive when the forward part of the longitudinal axis is directed above the reference line.
- тангажа на кабрирование — nose-up pitch angle
- тангажа на пикирование — nose-down pitch angle
- тангажа, текущий — present pitch angle, present angle of pitch
-, текущий путевой (тпу) — present track angle
- текущий путевой, запомненный (тзпу) — present stored track angle
- точки весеннего равноденствия, часовой, западный (астр.) — sidereal hour angle (sha) angular distance west of the vernal equinox.
-, тупой — obtuse angle
угол более 90о и менее 180о. — an obtuse angle is more than 90о but less than 180о.
- увлечения (картушки компаса) — compass card drift ang
- упреждения (для парирования сноса самолета при посадке) — drift-correction angle
- установки (см. угол заклинения аэродинамической поверхности) — setting angle
- установки горизонтального оперения — angle of stabilizer setting
- установки крыла (заклинение) — angle of wing setting, rigging angle of wing incidence
угол между корневой хордой крыла и базовой линией фюзеляжа (рис.135). — angle between the wing chord line and aircraft longitudinal axis.
- установки лопасти (винта) — blade angle
острый угол между хордой сечения лопасти возд.(или несущего, хвостового) винта и плоскостью перпендикулярной оси вращения (рис.58). — the acute angle between the chord of а section of a propeller, or of a rotary wing system, and a plane perpendicular to the axis of rotation.
- установки рычага управл. двигателем (руд) — throttle setting
- установки стабилизатора (заклинение) — angle of stabilizer setting, rigging angle of horizontal stabilizer incidence
угол между корневой хордой стабилизатора и базовой линией фюзеляжа (рис. 135). — angle between the stabilizer root chord line and aircraft longitudinal axis.
- установки (переставного) стабилизатора — stabilizer (incidence) setting
- установки стабилизатора, взлетный — takeoff stabilizer setting
- установки стабилизатора, посадочный — landing stabilizer setting
-, установочный (крыла, стабилизатора) — (wing, stabilizer) setting angle
-, фактический путевой (рис. 124) — (actual) track angle (tk)
- цели, курсовой — (target) angle-off
-, часовой — hour angle
angular distance west of a celestial meridian or hour circle.
- часовой, западный, точки весеннего равноденствия (астр.) — sidereal hour angle (sha)
выход за критический у. атаки — stall (angle) overshoot
выход на критический у. атаки — reaching of stall(ing) angle
диапазон у. атаки — angle-of-attack range
под углом к... — at angle to...
enter downwind at 90 to reference line.
полет на критическом у. атаки — stall flight
поправка на у. сноса — crosswind correction
расположение (нескольких элементов) под углом... град — spacing... deg. apart the propeller blades are spaced l20 apart.
с автоматическим учетом у. сноса — with crosswind (drift) correction automatically computed
выходить на закритический у. атаки — exceed the stalling angle
выходить на критический у. атаки — reach the stalling angle
задавать путевой у. — select (desired) track angle
закруглять у. (детали) — round (off) the corner
изменять у. атаки — change angle of attack
образовывать у. с... — make angle with...
the cable makes an angle of 10 degrees with the vertical line.
отклонять на у. (-10 град.) — deflect /displace/ (approximately 10 deg.)
отсчитывать у. — read the angle
поворачиваться на у. — turn /rotate/ through аn angle
подавать у. (т.е. эл. сигнал, соответствующий к-л. угловой величине) на (статор сельсина) — supply /transmit/ angular information to (synchro stator)
располагаться под у. град. (вокруг оси) — be located /spaced/... degrees apart (about axis)
устанавливать (закрылки) на желаемый у. — set (flaps) at desired angleРусско-английский сборник авиационно-технических терминов > угол (геометрический)
-
49 шкала
scale
часть отсчетного устройства с отметками (делениями, оцифровкой) для замера соответствующих величин. — а series of markings used for measurement or computation.
- азимутов (астрокомпаса) — azimuth circle
- азимутов (селектора курса) — obs azimuth card
the obs azimuth card indicates the 030o radial.
-, барометрическая (шкала давления высотомера) — pressure scale
- барометрического давления (высотомера) — (atmospheric, barometric) pressure scale, (altimeter) sub-scale
- видимости — visibility scale
- возвышений (астрокомпаса) — declination scale
- давления (давлений) высотомера — altimeter pressure scale, altimeter sub-scale
set the altimeter sub-scale to 1013 mb.
- дальности — distance scale
-, двусторонняя (прибора с центральным нулем) — center-zero scale
- кельвина — kelvin temperature scale (к)
- крена (неподвижная) (рис. 72) — bank scale
-, круглая — circular dial
- курса (рис. 73) — compass /azimuth/ card
- курсов (картушки прибора нкп) — compass card
-, ленточная — tape scale
-, ленточная (тангажа) — (pitch) tape
- магнитного курса (прибора (нпп) — compass card
-, неподвижная — fixed scale
-, неравномерная — nonlinear scale
-, нониусная — vernier scale
нониусная шкала микрометpa позволяет производить измерения с точностью до 1/1oooo дюйма. — the micrometer vernier scale enables the instrument to be used to measure to one tenthousandth part of an inch.
- отклонения от глиссады (рис. 73) — glide slope (deviation) scale
- отклонения от заданной скорости (рис. 72) — speed scale
- отклонения от заданной скорости или от оптимального угла атаки — speed scale
- отклонения от заданной траектории в вертикальной плоскости (от глиссады) (рис. 73) — glide slope (deviation) scale
- отклонения от заданной траектории в вертикальной плоскости (ш. полож. глиссады) (рис. 72) — glide slope scale
- отклонения от заданной траектории в горизонтальной плоскости (от курса) (рис. 73) — course deviation scale
- отклонения от заданной траектории в горизонтальной плоскости (ш. положения курса) (рис. 72) — localizer deviation (display) scale
- отклонения от курса — course deviation scale
при переходе планки положения курса первой точки шкалы отклонения от курса, установить индекс заданного курса в положение (90°), указываемое стрелкой зпу (рис. 73). — as the course deviation bar moves over the first dot of the course deviation scale from the center of the course arrow, set the heading marker (or bug) to the course arrow heading (90°).
- отклонения от курсовой зоны (рис. 72) — localizer deviation scale
-, подвижная — slide scale
- положения (аг прибора пкп) — attitude display
- положения глиссады — glide slope scale
средняя точка шкалы положения глиссады показывает положение самолета относительно глиссады (рис. 72). — the glideslope pointer represents the center of the gs beam, the center line (dot) of the gs scale represents aircraft position.
- положения курса (рис. 72) — localizer deviation (display) scale
- поправки тангажа (прибора кпп) — pitch trim scale
- прибора — instrument scale
-, равномерная — linear scale
-, растянутая — expanded scale
-, светящаяся — luminous scale
- скорости ветра — wind speed scale
-, сферическая — spherical scale
- тангажа (ленточная) — pitch tape
шкала тангажа закреплена на барабанах, перемещающих ее для индикации положения самолета в пространстве по тангажу. — the pitch tape is attached to rollers and thus is positioned to display pitch attitude of the aircraft.
- текущего курса — compass /azimuth/ card, azimuth ring
вращающаяся шкала планового навигационного прибора (пнп) (рис. 73). — heading information from a gyrostabilized magnetic compass is displayed by the rotating compass (azimuth) card.
- углов крена (рис. 72) — bank scale
- углов сноса (рис. 73) — drift scale
- углов тангажа (рис. 72) — pitch scale
- углов тангажа, ленточная — pitch tape
- указателя глиссады (приборов нкп н пп-1п) — glide slope (deviation) scale
- указателя обжатия амортизатора (шасси) — shock strut compression indicator scale
- указателя отклонения скорости самолета от заданной скорости (рис. 72) — speed scale
- указателя положения самолета относительно оси равносигнальной зоны курса (прибора нкп) — course deviation scale
- уклона впп (на графике) — runway slope grid
- установки (углового положения) лопасти — blade pitch setting scale
- фаренгейта — fahrenheit temperature scale (f)
шкала с точкой замерзания воды обозначенной 32° и точкой кипения 212°. пересчет в градусы цельсия по формуле. f=(9/5)с + 32 — a temperature scale wifh ice point at 32° and boiling point of water at 212°. conversion with the celsius (centigrade) temperature: f=(9/5)c + 32
- цельсия — centigrade temperature scale (c)
- часовых градусов (астрокомпаса) — hour-angle scale
- широт (астрокомпаса) — latitude dial
деление ш. — scale graduation /division/
диапазон ш. (прибора) — scale range
длина ш. (прибора) — scale length
отметка ш. — scale mark
по ш. — on scale
pressure is indicated on pressure gage scale.Русско-английский сборник авиационно-технических терминов > шкала
-
50 test
- test
- nиспытание; проверка; тест; опыт; проба; анализ; исследование; эксперимент || испытывать; проверять; исследовать
test by immersion in boiling water — проба [испытание] кипячением в воде
- test of time
- AASHO density test
- Abbot compaction test
- Abrams' test
- abrasion test
- absorption test
- accelerated test
- accelerated test for compressive strength
- accelerated strength test
- acceptance test
- accredited tests
- acid test
- aggregate crushing test
- aggregate impact test
- air test
- air content test
- air entrainment test
- air filter blackness test
- air leakage test
- air permeability test
- air permeability fineness test
- alternating bending test
- anchorage shear test
- aptitude test
- Atterberg test
- attrition test
- autoclave test
- baling-out permeability test
- ball test
- ball hardness test
- barium sulphate test
- beam test
- bearing test
- bending test
- bending tensile test
- bit wear test
- blackness air filter test
- Blain test
- block shear test
- blow flexure test
- boiling test
- bond test
- bootstrap test
- borehole shear test
- breaking test
- Brinell hardness test
- California bearing ratio test
- cement tests
- Charpy test
- Charpy V-notch impact test
- checking test
- check test
- COLE volume change test
- colorimetric test
- color test
- compacting factor test
- compaction test
- complience test
- compression test
- cone penetration test
- consistency test
- consolidated quick test
- consolidation test
- constant head permeability test
- constant rate of penetration test
- constant rate of uplift test
- constant volume test
- control test
- core test
- creep test
- C.R.P. test
- crushing test
- cube strength test
- cube test
- cylinder test
- dehydration test
- diametral compression test
- diamond pyramid hardness test
- dioctylphthalate test
- direct shear test
- dispersion test
- dissipation test
- DOP test
- Dorry test
- drain test
- drained triaxial test
- driving test
- drop-weight test
- durability test
- dust spot test
- Dutch sounding test
- dynamic penetration test
- expandable sleeve concrete test
- exposure tests
- fast field tests
- fatigue test
- field tests
- field density test
- field loading test
- field percolation test
- field vane test
- flexure test
- flow-table test
- flow test
- four-point bending test
- fracture test
- freeze-thaw test
- freeze-thaw durability test
- freezing test
- gravimetric air filter test
- hardening test of concrete
- hardness test
- Herbert cloudburst test
- hollow cylinder test
- hydraulic drain test
- hydraulic flat-jack test
- hydraulic pressure test
- hydraulic test
- hydrostatic test
- impact test
- impact crushing value test
- indentation test
- ink test
- in-place test
- in-place slump test
- in-situ test
- in-situ soil tests
- insulation test
- integrity test
- Izod impact test
- Izod test
- jolt test
- Kelly ball test
- Knoop hardness test
- laboratory test
- leakage test
- life test
- line-load test
- load test of structures
- loading test
- long-term test
- long-time creep test
- maintained load test
- manufacturer test
- methylene blue test
- model test
- needle test
- notch bending test
- notched bar test
- nuclear density test
- operational test
- organic test
- organic test for fine aggregate
- orifice tube test
- penetration test
- percussion test
- performance test
- photoelastic test
- pile load test
- pile pulling test
- pile redriving test
- plate-bearing test
- pneumatic test
- point-load test
- preliminary test
- pressure test
- pressure meter test
- proof test
- proof load test
- pumping test
- punching shear test
- pycnometer test
- Q-test
- quick test
- R-test
- Ro test
- radial percolation test
- Raymond standard test
- reception test
- reference test
- reliability test
- repeated load test
- resonant-column test
- reverse bend test
- rock bolts convergence test
- Rockwell hardness test
- Rockwell superficial hardness test
- S-test
- saponification test
- scratch test
- shearing test
- shear test
- shock bending test
- short-term test
- single point test
- site test for cement content of mortars
- slow test
- slump test
- smoke test
- soap test
- splitting tensile test
- standard-density test
- standard penetration test
- static penetration test
- strength test
- stress-relaxation test
- stress-rupture test
- tensile test
- tightness test
- time-of-set test
- torsion test
- triaxial compression test
- triaxial test
- two-point test
- type test
- ultrasonic test
- undrained test
- vacuum test
- vane test
- vibrated mortar cube test
- vibrating crushing test
- Vicat needle test
- water test
- water loading test
- water retention test
- wind loading test
- wind-tunnel test
- works beam test
- works cube test
- yield test
Англо-русский строительный словарь. — М.: Русский Язык. С.Н.Корчемкина, С.К.Кашкина, С.В.Курбатова. 1995.
-
51 key
1) ключ2) гаечный ключ3) замок; замковый камень ( арки или свода)4) шпонка; пластинчатый нагель || крепить шпонкой; сажать на шпонку5) клин; шплинт || крепить клином или шплинтом6) расшивка ( инструмент)7) насекать поверхность под штукатурку8) перевязывать швы ( в кладке)9) ключ; кнопка; кнопочный переключатель; клавиша || нажимать кнопку; нажимать клавишу11) направляющий ключ (напр. цоколя лампы)12) вчт. ключ; шифр13) полигр. изображение-основа14) пояснение в подрисуночной подписи; экспликация•to drift out a key — выбивать ( выколачивать) шпонку;to seat a key — ставить шпонку;to key to surface — сцепляться с поверхностью-
accent key
-
access key
-
activate key
-
actual key
-
adjusting key
-
aligning key
-
alignment key
-
Allen key
-
alphanumeric keys
-
alphameric keys
-
angle cock key
-
announcer's key
-
answering key
-
anticlash key
-
arch key
-
armature head lock key
-
armature keys
-
assignment key
-
attention key
-
automatic cancel key
-
auxiliary key
-
averaging key
-
axle-lining key
-
backspace key
-
backup key
-
brake hanger key
-
brake shoe key
-
break key
-
breakout key
-
bridge key
-
buffered key
-
busy key
-
calling key
-
call key
-
cancel transmission key
-
canceling key
-
cancel key
-
candidate key
-
cap key
-
carriage release key
-
carriage restore key
-
censor key
-
center key
-
chamfered key
-
character key
-
check key
-
cipher key
-
clearing key
-
clear key
-
code key
-
column layout key
-
command key
-
concatenated key
-
concrete key
-
control key
-
correction key
-
coupler shank pin retaining key
-
crypto key
-
current-reversing key
-
cursor key
-
cutoff key
-
dazzle-free key
-
decimal tabulator key
-
deck support key
-
de-jammer key
-
delete key
-
dive key
-
dog damping key
-
double-dovetail key
-
double-function key
-
draft key
-
draw key
-
ductor key
-
editing key
-
edit key
-
encryption key
-
end-of-page key
-
enter key
-
erase key
-
escape key
-
exclusion key
-
exit key
-
extra key
-
feather key
-
figure key
-
flat key
-
foreign key
-
format recall key
-
fox key
-
fully concatenated key
-
functional key
-
function key
-
generic key
-
gib-headed key
-
gib-head key
-
half-space key
-
halt key
-
hammerhead key
-
hardware storage key
-
hold-down tabulator key
-
home key
-
index key
-
ink key
-
interference-fit key
-
interruption key
-
interrupt key
-
justification key
-
keying-fit key
-
lie key
-
line recall key
-
line spacing key
-
load key
-
locator key
-
locking key
-
loose key
-
lower rail key
-
major key
-
margin key
-
margin-release key
-
memory key
-
memory total key
-
microadjustable key
-
monitoring key
-
Morse key
-
multifunction key
-
nonlocking key
-
numbered key
-
number key
-
numeric shift key
-
numerical key
-
numeric key
-
occupation key
-
operating key
-
order-wire key
-
paper ejection key
-
paper injection key
-
paper positioning key
-
paragraph indentation key
-
party line ringing key
-
pass key
-
pattern key
-
phrase recall key
-
pin key
-
plug key
-
point key
-
primary key
-
privacy key
-
private key
-
programmable key
-
prong key
-
protection key
-
public key
-
pulsing key
-
radial key
-
reading key
-
read key
-
recall key
-
release key
-
relocate typing point key
-
removable key
-
repeat key
-
resetting key
-
reset key
-
return and vertical spacing key
-
return key
-
reverse key
-
rhythm-compensation key
-
ring-back key
-
ringing key
-
round key
-
route canceling key
-
route key
-
rubout key
-
screw key
-
search key
-
secondary key
-
selector key
-
semicircular key
-
sending key
-
sequencing key
-
shear key
-
shift key
-
shift-lock key
-
signaling key
-
sliding key
-
sloped key
-
socket key
-
soft key
-
sorting key
-
sort key
-
space key
-
spacing key
-
speaking key
-
split key
-
spring buckle key
-
start key
-
stop key
-
storage key
-
straight key
-
switching key
-
switch key
-
switch-lock key
-
tabulating key
-
tab key
-
tabulator clearing key
-
tab clearing key
-
tabulator-set key
-
talking key
-
tangential key
-
tangent key
-
tapered key
-
taper key
-
telegraph key
-
test key
-
tightening key
-
title centering key
-
total tabulator clearing key
-
touch-sensitive key
-
touch key
-
track key
-
track link key
-
track shoe key
-
transfer key
-
turn key
-
typamatic key
-
upper rail key
-
user-defined key
-
voice key
-
wedge key
-
Woodruff key
-
write key -
52 saw
1) пила ( станок или инструмент) || пилить, распиливать, разрезать пилой2) многорезцовый режущий [распиловочный\] инструмент3) лезвие пилы5) дисковый нож ( хлеборезки)•to saw down — спиливать ( дерево);to saw off — отпиливать;to saw out — выпиливать;to set saw — разводить пилу;-
abrasive saw
-
abrasive-wire saw
-
acid saw
-
annular saw
-
band saw
-
batch saw
-
belt saw
-
bench saw
-
board saw
-
bone saw
-
bow saw
-
brick saw
-
buck saw
-
butcher saw
-
carbide-tipped saw
-
carcass breaking saw
-
chain saw
-
circular cutoff saw
-
cleaving saw
-
cold-cutting saw
-
compass saw
-
coping saw
-
cropping saw
-
cross-cut saw
-
cutoff saw
-
cylinder saw
-
diamond impregnated saw
-
diamond saw
-
dicing saw
-
direct-drive saw
-
disk saw
-
dovetail saw
-
edging saw
-
electric power saw
-
electric saw
-
flooring saw
-
flying hot saw
-
frame saw
-
fret saw
-
friction saw
-
gang saw
-
grooving saw
-
hand saw
-
hinge saw
-
hole saw
-
horizontal sliding-frame hot saw
-
hot drop saw
-
ice saw
-
inner diameter saw
-
inserted-tooth circular saw
-
jeweller's saw
-
jig saw
-
keyhole saw
-
line saw
-
link tooth saw
-
masonry saw
-
meat band saw
-
metal slitting saw
-
metal-working saw
-
motorized saw
-
outer diameter saw
-
parting saw
-
pit saw
-
portable saw
-
power saw
-
production saw
-
radial arm saw
-
rail cutting saw
-
rail saw
-
rim saw
-
ring saw
-
rip saw
-
rocking-type hot saw
-
rocking-type saw
-
rotary saw
-
saber saw
-
scrap saw
-
shingle saw
-
shuttle saw
-
single-band saw
-
single-handled saw
-
single-wire saw
-
slotting saw
-
stone saw
-
straight-cut saw
-
strap saw
-
string saw
-
suspended saw
-
swing saw
-
table saw
-
tenon saw
-
tilt saw
-
traveling table band saw
-
trimming saw
-
trump saw
-
twin saw
-
wafer dicing saw
-
warm saw
-
wire saw
-
wood-working saw -
53 gate
1) ворота
2) воротный
3) заставка
4) калитка
5) литник
6) литниковый
7) неотпирающий
8) открыть
9) полустроб
10) селекторный
11) шибер
12) шиберный
13) схема совпадений
14) клапан
15) вентиль
16) селектор
17) запускающий импульс
18) стробирующий импульс
19) пропускать сигнал
20) дверь
21) заслонка
22) затвор
23) рамный
24) задвижка
25) <tech.> стробимпульс
26) стробировать
– add gate
– aft gate
– amplitude gate
– ancicoincidence gate
– AND gate
– ash gate
– ash-discharge gate
– balanced gate
– bin control gate
– bin gate
– blast gate
– boom gate
– bulkhead gate
– butterfly gate
– caisson gate
– carry gate
– central gate
– chain gate
– chute gate
– clearance gate
– clinket gate
– coincidence gate
– compatible gate
– control gate
– crest gate
– cylinder gate
– deep gate
– delayed gate
– diode gate
– discharge gate
– double gate
– down gate
– drop gate
– duplicate gate
– early gate
– emergency gate
– exclusive OR gate
– film gate
– finger gate
– flap gate
– flood gate
– flux gate
– gate aperture
– gate array
– gate blade
– gate capacitance
– gate circuit
– gate closes
– gate conveyor
– gate duration
– gate electrode
– gate generator
– gate insulator
– gate length
– gate mask
– gate non-trigger-current
– gate opens
– gate post
– gate pulse
– gate receiver
– gate region
– gate resistance
– gate tube
– gate valve
– hinged gate
– horn gate
– ice gate
– inhibitory gate
– lap gate
– late gate
– lift gate
– locking gate
– logic gate
– logical gate
– majority gate
– mitre gate
– NAND gate
– narrow gate
– narrow-narrow gate
– needle gate
– NOR gate
– NOT gate
– overinterrogation gate
– overlapping bin gate
– overpour gate
– pencil gate
– pin-point gate
– pivot-leaf gate
– plain gate
– proportioning bin gate
– pulse gate
– radial gate
– ring gate
– roller gate
– roller-bearing gate
– rolling gate
– roof gate
– search gate
– sector gate
– service gate
– set of gate patterns
– shift gate
– shower gate
– slide gate
– sliding gate
– sluice gate
– spray gate
– stem gate
– sticking of gate
– strobe gate
– sum-out gate
– tail gate
– thyratron gate
– trigger gate
– upper gate
– wedge gate
– weigh-hopper gate
– wicket gate
– wide gate
– zero gate
insulated gate FET — полевой транзистор с изолированным затвором
main steam gate — <phys.> задвижка паровая главная
master-slice gate array — базовая матрица логических элементов
non-rising-stem gate valve — задвижка с невыдвижным шпинделем
triple-control-grid gate tube — лампа-вентиль с тремя управляющими сетками
-
54 radio
1) радио
2) радиоприемник
3) передавать по радио
4) радиоприемный
– A-N radio range
– battery-operated radio
– by radio
– car radio
– console radio
– contact by radio
– get on for radio contact
– jam radio station
– mains-operated radio
– radio altimeter
– radio astronomy
– radio beacon
– radio bearing
– radio broadcasting
– radio channel
– radio transmitter
– radio universe
– radio waves
– transistor radio
– transmit by radio
– tube radio
– use radio contact
amateur radio operator — < radio> коротковолновик, радиолюбитель
high-altitude radio altimeter — радиовысотомер больших высот
interferometer radio telescope — интерференционный радиотелескоп
multichannel radio communication — многоканальная радиосвязь
nondirectional radio beacon — <aeron.> радиостанция приводная
point-to-point radio transmission — радиопередача направленная
radio direction finding — <naut.> радиопеленгация
radio direction-finding station — радиопеленгаторная станция
radio relay link — < radio> линия релейная
ship-to-ship radio communication — радиосвязь между кораблями
stereophonic radio receiver — стереофонический радиоприемник
survival-craft radio station — радиостанция средств спасения
-
55 saw
1) испиливать
2) испилить
3) козел
4) пила
5) пильный
6) распиливать
– abrasive saw
– barrel saw
– bevel saw
– bone saw
– bow saw
– butting saw
– chain saw
– circ saw
– circular saw
– cleaving saw
– cold saw
– compass saw
– coping saw
– cross-cut saw
– crosscut saw
– cutting-off saw
– diamond saw
– dimensioning saw
– direct-drive saw
– dovetail saw
– drop saw
– edginer saw
– edging saw
– file saw
– fit saw
– frame saw
– friction saw
– gang saw
– grooving saw
– hinge saw
– hot saw
– ice saw
– log saw
– metal-working saw
– petrol saw
– pit saw
– radial saw
– rim of circular saw
– ring saw
– rocking-type saw
– rope saw
– saw blade
– saw bow
– saw carriage
– saw cylinder
– saw diamond
– saw frame
– saw gauge
– saw gin
– saw kerf
– saw mill
– saw sharpening wheel
– saw spindle
– saw timber
– saw tooth curve
– saw tooth setting
– saw web
– set saw
– sing-handled saw
– sliding-frame saw
– stone saw
– swing saw
– trimming saw
– trump saw
– wire saw
– wood-working saw
abrasive cutoff saw — <tech.> круг абразивный отрезной
-
56 system
1) система
2) комплекс
3) совокупность
4) множество
5) область
6) схемный
7) устройство
8) системный
– adaptive system
– addressing system
– airdrop system
– antenna system
– arithmetic system
– blok system
– bus system
– c.m. system
– center-of-mass system
– classification system
– commutation system
– controlled system
– cooling system
– crossbar system
– cryoelectronic system
– deferlant system
– deflection system
– dial system
– distributed system
– double-current system
– doudecimal system
– draft system
– drainage system
– earth system
– ecological system
– encoder system
– energy system
– error-controlled system
– evaporator system
– exhaust system
– file system
– finder system
– floating-carrier system
– floating-point system
– focusing system
– fuel system
– gas-cleaning system
– gas-pressurized system
– ground system
– guidance system
– history of a system
– hot-water system
– hydraulic system
– identifiable system
– inertial system
– inteblock system
– Korsch system
– laboratory system
– Lesniewski system
– life-support system
– lightguiding system
– linear system
– monitoring system
– multimicroprocessor system
– multiple-data-set system
– non-autonomous system
– nondirector system
– number system
– parallel-feed system
– piece-rate system
– planetary system
– pneumatic system
– propulsion system
– prototype system
– public-address system
– quadrophonic system
– queuing system
– response of system
– right-handed system
– robot system
– safety-trip system
– sampled-data system
– scanning system
– sewage system
– shift system
– spraying system
– sprinkling system
– staff system
– stand-by system
– start-stop system
– start-up system
– storage system
– system behavior
– system check
– system debugging
– system design
– system failure
– system of equations
– system of imprimitivity
– system of wheels
– system reliability
– system topology
– tally system
– telephone system
– television system
– ten-step system
– timing system
– transmission system
– triangulation system
– triclinic system
– twelve-channel system
– two-particle system
– unattended system
– unstable system
– ventilation system
– video system
– warning system
– water-sludge system
– wellpoint system
aircraft electrical system — <aeron.> сеть бортовая электрическая
ample linear system — <math.> система линейная обильная
approach and docking system — <cosm.> система сближения и стыковки
automated/automatic landing system — <aeron.> система захода на посадку автоматизированная
automatic block system — < railways> автоблокировка
automatic deicing system — <aeron.> автомат противообледенительной системы
bang-bang control system — <comput.> система управления релейная
carrier frequency system — система передачи с частотным разделением каналов
Cartesian coordinate system — прямоугольная система координат
closed-circuit television system — <commun.> система телевидения невещательная
cycle matching system — <aeron.> навигация воздушная импульсная, система навигационная импульсная
differential selsyn system — дифсельсин, сельсин дифференциальный
digital counting system — <comput.> система отслеживающая цифровая
digital transmission system — <commun.> система передачи цифровая
disk operating system — <comput.> система операционная дисковая
dispatch telephone system — диспетчерская телефонная система
fiber-optics communication system — <commun.> система связи волоконно-оптическая
hereditarily generating system — наследственная система образующих
hexadecimal number system — шестнадцатиричная система счисления
information retrieval system — <comput.> система информационно-поисковая
integrated switching system — интегральная коммутационная система
itnegrated manufacturing system — комплексная автоматическая линия
jet engine starter system — <engin.> турбостартер
meteor-burst communication system — <commun.> система связи метеорная
microprocessor control system — микропроцессорная система управления
modular pneumatic-device system — система унифицированная агрегатная
modular programming system — <comput.> система модульного программирования
multipoint distribution system — многоадресная система распределения ТВ-программ
packet transmission system — система передачи с коммутацией пакетов сообщений
Pitot static system — <engin.> система ПВД
pulsed navigation system — <aeron.> навигация воздушная импульсная, система навигационная импульсная
quantum-mechanical readout system — <tech.> система считывающая квантовая
quasi-electronic switching system — квазиэлектронная система коммутации
reactor control system — <engin.> система управления и защиты
reactor protection system — <phys.> защита аварийная
receiver-amplifier crioelectric system — приемно-усилительная криоэлектронная система
remote-cylinder hydraulic system — раздельно—агрегатная гидросистема
resultant of system of forces — равнодействующая системы сил
satellite navigation system — <naut.> система навигационная космическая, система навигационная спутниковая
State System of Instruments — <engin.> система приборов Государственная
supervisory control system — <comput.> автодиспетчер
system of residual classes — <math.> система остаточных классов
telegraph block system — < railways> движение поездов по телеграфному соглашению
time interval system — < railways> разграничение поездов временем
time-division multiplex system — система передачи с временным разделением
unified radiotelemetry system — унифицированный радиотелеметрический комплекс
-
57 GSR
1) Компьютерная техника: Global Set Reset2) Американизм: Government Social Research3) Спорт: Grand Sport Racing4) Военный термин: General Staff Requirements, general service recruit, general support reinforcing, ground surveillance radar, gun sound ranging5) Техника: generic safety report, gland steam regulator, glide slope receiver6) Сокращение: General Staff Requirement (USA), Gun Shot Residue7) Университет: Graduate Student Researcher, Green Student Representatives8) Физиология: Galvanized Skin Response9) Генетика: глутатионредуктаза10) СМИ: Great Sounding Radio11) Сетевые технологии: Gigabit Switch Router12) Полимеры: giant steel radial, government synthetic rubber13) Авиационная медицина: galactic space radiation, galvanic skin reflex14) Макаров: galvanic skin response15) AMEX. Golden Star Resources, LTD., of Canada -
58 RSP
1) Общая лексика: ССБ2) Компьютерная техника: Really Special People, Required Space3) Медицина: right sacrum posterior4) Американизм: Reality Signal Processor5) Военный термин: radar signal processor, range support plan, rapid site preparation, recognized surface picture, reconnaissance and security positions, regional strike plan, render safe procedure, replenishment spare parts, reserve stock point6) Техника: reactivity surveillance procedure, reentry system programmer, remote shutdown panel, rendezvous station panel, responder beacon, rotating shield plug7) Железнодорожный термин: Roscoe Snyder and Pacific Railway8) Грубое выражение: Retarded Stupid People9) Сокращение: Ringshell projector (Underwater sound projector), Radial Serial Protocol, ReSPonse, Remote Set Point10) Вычислительная техника: Reality Signal Processor (Nintendo)11) Нефть: separator producing gas/oil ratio12) Связь: Routing Switch Platform (Alcatel 7670 RSP)13) Фирменный знак: Retail Service Provider, Rover Special Products14) Сетевые технологии: Route- Switch Processor15) Программирование: Rounding To Single Precision16) Химическое оружие: render-safe procedures17) Порошковая металлургия: БОП (rapidly solidified powder - быстроотверждённый порошок)18) Расширение файла: Required Space Character, Response file19) Должность: Resource Specialist Program20) Аэропорты: Raspberry Strait, Alaska USA -
59 rsp
1) Общая лексика: ССБ2) Компьютерная техника: Really Special People, Required Space3) Медицина: right sacrum posterior4) Американизм: Reality Signal Processor5) Военный термин: radar signal processor, range support plan, rapid site preparation, recognized surface picture, reconnaissance and security positions, regional strike plan, render safe procedure, replenishment spare parts, reserve stock point6) Техника: reactivity surveillance procedure, reentry system programmer, remote shutdown panel, rendezvous station panel, responder beacon, rotating shield plug7) Железнодорожный термин: Roscoe Snyder and Pacific Railway8) Грубое выражение: Retarded Stupid People9) Сокращение: Ringshell projector (Underwater sound projector), Radial Serial Protocol, ReSPonse, Remote Set Point10) Вычислительная техника: Reality Signal Processor (Nintendo)11) Нефть: separator producing gas/oil ratio12) Связь: Routing Switch Platform (Alcatel 7670 RSP)13) Фирменный знак: Retail Service Provider, Rover Special Products14) Сетевые технологии: Route- Switch Processor15) Программирование: Rounding To Single Precision16) Химическое оружие: render-safe procedures17) Порошковая металлургия: БОП (rapidly solidified powder - быстроотверждённый порошок)18) Расширение файла: Required Space Character, Response file19) Должность: Resource Specialist Program20) Аэропорты: Raspberry Strait, Alaska USA -
60 гитара
1) General subject: easy rider, easy-rider, guitar, quadrant2) Engineering: bracket (станка), change-gear quadrant, gear reduction unit, guitar (музыкальный инструмент), swing arm, swinging arm, swivel head3) Construction: main gas pipeline4) Railway term: adjusting plate (токарного станка)5) Jargon: belly fiddle, gitbox, guinea's harp6) Mechanic engineering: change gear, change-gear train, horse's head, quadrant plate, radial, swing frame
См. также в других словарях:
Radial basis function network — A radial basis function network is an artificial neural network that uses radial basis functions as activation functions. They are used in function approximation, time series prediction, and control.Network architectureRadial basis function (RBF) … Wikipedia
set — Synonyms and related words: A to Z, A to izzard, Brownian movement, Platonic form, Platonic idea, Zeitgeist, abet, accepted, accommodate, accord, accretion, acrid, aculeate, acuminate, acute, adapt, address, adhere, adherence, adhesion, adjust,… … Moby Thesaurus
Organización Radial Olímpica — (ORO) is a Colombian group of radio stations, which belongs to the wealthy and influential Char Abdalá family from Barranquilla.[1] It started in 1969 with the purchase of Radio Regalo AM of Barranquilla, which would be renamed Radio Olímpica AM … Wikipedia
Determining the number of clusters in a data set — Determining the number of clusters in a data set, a quantity often labeled k as in the k means algorithm, is a frequent problem in data clustering, and is a distinct issue from the process of actually solving the clustering problem. For a certain … Wikipedia
Dado set — Top left: disassembled stacked dado set showing blades and chippers; bottom left: stacked dado set in table saw; right: wobble dado A dado set or dado blade is a type of circular saw blade, usually used with a table saw or radial arm saw, which… … Wikipedia
Absorbing set — In functional analysis and related areas of mathematics an absorbing set in a vector space is a set S which can be inflated to include any element of the vector space. Alternative terms are radial or absorbent set.DefinitionGiven a vector space X … Wikipedia
Drum set tuning — Contents 1 Drum Set Tuning 1.1 Tom Toms 1.2 Snare drum and bass drum 1.3 The Process 1.4 Muffling … Wikipedia
turbine — /terr bin, buyn/, n. any of various machines having a rotor, usually with vanes or blades, driven by the pressure, momentum, or reactive thrust of a moving fluid, as steam, water, hot gases, or air, either occurring in the form of free jets or as … Universalium
VHF omnidirectional range — This article is about the radio navigation aid. For other uses, see Vor. D VOR (Doppler VOR) ground station, co located with DME … Wikipedia
Atomic orbital — The shapes of the first five atomic orbitals: 1s, 2s, 2px, 2py, and 2pz. The colors show the wave function phase. These are graphs of ψ(x,y,z) functions which depend on the coordinates of one electron. To see the elongated shape of ψ(x,y,z)2… … Wikipedia
Weather radar — in Norman, Oklahoma with rainshaft … Wikipedia