-
121 nestekitkalla toimiva säteisliukulaakeri
journal clearance bearing; radial clearance bearingSuomi-Englanti sanakirja koneenosien > nestekitkalla toimiva säteisliukulaakeri
-
122 подшипник скольжения радиальный с жидкостным трением
journal clearance bearing; radial clearance bearingРусско-английский словарь по деталям машин > подшипник скольжения радиальный с жидкостным трением
-
123 в соответствии с
. в зависимости от; изменяться в соответствии с кривой; классификация по; находиться в соответствии с; согласно; соответствие•In line with this assumption, we have devised a model of...
•To modify the beach profile in response to changing wave conditions...
•Evaporators for marine use are classed as horizontal or vertical by (or according to, or depending on) the position of their tubes.
•The test report is performed in accord( ance) (or conformity, or compliance) with the specifications.
•In keeping with the limitation of only four orbitals, the formation of double or triple bonds between atoms of these elements reduces the coordination number of the central atom.
•The machine is designed and built to higher standards of accuracy.
•The sketch can be interpreted in terms of either system.
•The console pressure can be regulated to match the individual gauge range.
•In the reactors designed around this approach the energy-carrying neutrons released by thermonuclear reactions will be absorbed in a lithium blanket.
•These techniques must be selected in relation to the properties of the substances being separated.
* * *В соответствии с (нормами)The specimens were tested at a frequency of approximately 130 Hz, following ASTM E466 [...].В соответствии с -- in accordance with, in agreement with, in keeping with, in line with, in compliance with, consistent with; as required by, to match, following, according to; in step with (синхронно); per (в инструкциях); to conform to (о требованиях стандарта и т. п.), pursuant to (в письмах)Fatigue life results of the bearings tested were statistically analyzed in accordance with the methods of [...].In agreement with this, it was found that the low ф machine went into a part-span stall.Also, in keeping with practice, the inter-plate spacing was made equal to the plate length.The section on low-pressure heating boilers now had testing and marking requirements in line with those of the power boiler section.(Tf -- Ts) is kept fixed by increasing Ts with time as required by the surface temperature, Ts.Normally, this value of radial clearance is established to match the bearing size.According to a previous investigation of dressing [...], fracture can occur within the grain.The Sh number increases in step with the wake turbulence.Install housing and grease per figure and table.They are metered by orifice plate assemblies built to conform to BS 1042.Pursuant to your request, I am confirming our consent to the publication of the book in two volumes.Floating roof tanks generally do not require protection when installed in compliance with Section...Русско-английский научно-технический словарь переводчика > в соответствии с
-
124 зазор между стенками
oil&gas: radial clearanceУниверсальный русско-английский словарь > зазор между стенками
-
125 зазор между стенками концентричных элементов внутрискважинного оборудования
oil&gas: radial clearanceУниверсальный русско-английский словарь > зазор между стенками концентричных элементов внутрискважинного оборудования
-
126 зазор между шнеком и цилиндром
Plastics: radial clearanceУниверсальный русско-английский словарь > зазор между шнеком и цилиндром
-
127 концентричный зазор
Oil&Gas technology radial clearanceУниверсальный русско-английский словарь > концентричный зазор
-
128 радиальный зазор подшипника
Engineering: radial clearance of bearingУниверсальный русско-английский словарь > радиальный зазор подшипника
См. также в других словарях:
radial clearance — See radial play … Dictionary of automotive terms
clearance — A given amount of space between two parts such as between piston and cylinder, bearing and journal , etc. Also see bearing clearance front wheel tire clearance ground clearance control ground clearance lateral clearance lateral tire cl … Dictionary of automotive terms
Radial arm saw — A radial arm saw is a cutting machine consisting of a circular saw mounted on a sliding horizontal arm. Invented in 1923, the radial arm saw was the primary tool used for cutting long pieces of stock to length until the introduction of the miter… … Wikipedia
radial play — A bearing clearance in the radial direction … Dictionary of automotive terms
Hydraulic clearance — Hydraulic clearance. Flow in narrow clearances are of vital importance in hydraulic system component design. The flow in a narrow circular clearance of a spool valve can be calculated according to the formula below if the height is negligible… … Wikipedia
crest clearance — noun : the radial clearance between the crest of a screw thread and the root of the thread mating with it … Useful english dictionary
Sommerfeld number — In the design of fluid bearings, the Sommerfeld number, or bearing characteristic number, is a dimensionless quantity used extensively in hydrodynamic lubrication analysis. The Sommerfeld number is very important in lubrication analysis because… … Wikipedia
Cold saw — A 185 mm (7.3 in) hand held cold saw A cold saw bl … Wikipedia
Cold saw blade — Cold saw blades are circular metal cutting saw blades categorized into two types: Solid High Speed Steel (HSS) or Tungsten Carbide Tipped (TCT). Both types of blades are resharpenable and may be used many times before being discarded. Cold saw… … Wikipedia
минимальный радиальный зазор некруглоцилиндрического подшипника скольжения — (6.6) Минимальное расстояние между поверхностями скольжения соосно расположенных вала и подшипника. [ГОСТ ИСО 4378 1 2001] Тематики подшипники Обобщающие термины размерные характеристики подшипников скольжения EN minimum bearing radial clearance… … Справочник технического переводчика
относительный радиальный зазор круглоцилиндрического подшипника — Ψ Отношение радиального зазора к внутреннему радиусу круглоцилиндрического подшипника. [ГОСТ ИСО 4378 4 2001] Тематики подшипники Обобщающие термины геометрические показатели EN relative radial clearance of a circular cylindrical bearing FR… … Справочник технического переводчика