-
1 реле задержки импульса, отсчитываемой от подачи напряжения на управляющий вход
- relais à impulsion retardée avec signal de commande, m
реле задержки импульса, отсчитываемой от подачи напряжения на управляющий вход
-
[Интент]EN
pulse delayed relay with control signal
time relay in which the time delay starts when applying the power supply and the control signal; the output momentarily switches for an interval to the operate condition after the setting time has elapsed (see Figure 9)
NOTE 1 – Cycling the control signal during the time delay will not retrigger the time delay.
NOTE 2 – Manufacturer should specify if interval is fixed or variable.
[IEV ref 445-01-12]FR
relais à impulsion retardée avec signal de commande, m
relais temporisé dont la temporisation démarre dès l’application de l’alimentation et du signal de commande et dont la sortie passe momentanément à l’état de travail pour un intervalle donné dès que la temporisation est écoulée (voir Figure 9)
NOTE 1 – La répétition du signal de commande pendant le délai peut ne pas réinitialiser la temporisation.
NOTE 2 – Il convient pour le fabricant d’indiquer si la durée de l’intervalle est fixe ou réglable.
[IEV ref 445-01-12]Тематики
EN
DE
- impulsverzögertes Relais mit Steuersignal, n
FR
- relais à impulsion retardée avec signal de commande, m
Русско-французский словарь нормативно-технической терминологии > реле задержки импульса, отсчитываемой от подачи напряжения на управляющий вход
-
2 реле периодической последовательности импульсов
- relais clignotant, m
реле периодической последовательности импульсов
-
[Интент]
EN
flasher relay
repeat cycle relay
time relay in which the output periodically switches on and off as long as the power supply or control signal is applied (see Figure 5)
NOTE 1 – Depending on the relay type, the output starts with "pulse on" or "pulse off".
NOTE 2 – Flasher relay may also be initiated with a control signal.
[IEV ref 445-01-06]FR
relais clignotant, m
relais temporisé dans lequel la sortie passe périodiquement de l'état de travail à l'état de repos tant que l’alimentation ou le signal de commande est appliqué (voir Figure 5)
NOTE 1 – Selon le type de relais, la sortie démarre dans l'état de travail ou dans l'état de repos.
NOTE 2 – Le relais clignotant peut aussi être amorcé par un signal de commande.
[IEV ref 445-01-06]Тематики
EN
DE
- Blinkrelais, n
FR
- relais clignotant, m
Русско-французский словарь нормативно-технической терминологии > реле периодической последовательности импульсов
См. также в других словарях:
Control system — For other uses, see Control system (disambiguation). A control system is a device, or set of devices to manage, command, direct or regulate the behavior of other devices or system. There are two common classes of control systems, with many… … Wikipedia
Pulse-width modulation — (PWM) of a signal or power source involves the modulation of its duty cycle, to either convey information over a communications channel or control the amount of power sent to a load. PrinciplePulse width modulation uses a square wave whose pulse… … Wikipedia
Pulse-position modulation — is a form of signal modulation in which M message bits are encoded by transmitting asingle pulse in one of 2^M possible time shifts. This is repeated every T seconds, such thatthe transmitted bit rate is M/T bits per second. It is primarily… … Wikipedia
Pulse generator — Pulse generators can either be internal circuits or pieces of electronic test equipment used to generate pulses. Features Simple pulse generators usually allow control of the pulse repetition rate (frequency), pulse width, delay with respect to… … Wikipedia
Signal lamp — training during World War II. A signal lamp (sometimes called an Aldis lamp, named after Arthur C. W. Aldis who invented a widely used design) is a visual signaling device for optical communication (typically using Morse code). Modern signal… … Wikipedia
Signal integrity — or SI is a measure of the quality of an electrical signal. In digital electronics, a stream of binary values is represented by a voltage (or current) waveform. Over short distances and at low bit rates, a simple conductor can transmit this with… … Wikipedia
Pulse-code modulation — PCM redirects here. For other uses, see PCM (disambiguation). Pulse code modulation (PCM) is a method used to digitally represent sampled analog signals. It is the standard form for digital audio in computers and various Blu ray, Compact Disc and … Wikipedia
Pulse shaping — In digital telecommunication, pulse shaping is the process of changing the waveform of transmitted pulses. Its purpose is to make the transmitted signal suit better to the communication channel by limiting the effective bandwidth of the… … Wikipedia
Pulse-amplitude modulation — Principle of PAM: (1) original signal, (2) PAM signal, (a) amplitude of signal, (b) time Pulse amplitude modulation, acronym PAM, is a form of signal modulation where the message information is encoded in the amplitude of a series of signal… … Wikipedia
Pulse Code Cab Signaling — Amtrak Führerstandsanzeige Das Pulse Code Cab Signaling ist ein den USA verbreitetes Zugsicherungssystem, der Begriff bedeutet puls code modulierte Führerstandssignalisierung . In der Grundversion überträgt es wie das itialienische RS4 Codici… … Deutsch Wikipedia
Pulse dialing — Middle 20th century rotary dial telephone Pulse dialing, dial pulse, or loop disconnect dialing, also called rotary or decadic dialling in the United Kingdom (because up to 10 pulses are sent), is pulsing in which a direct current pulse train is… … Wikipedia