Перевод: с французского на русский

с русского на французский

phase+device-...

  • 1 matériel monophasé

    1. однофазное электротехническое устройство

     

    однофазное электротехническое устройство
    Электротехническое устройство, предназначенное для включения в однофазную электрическую цепь и не предназначенное для преобразования числа фаз.
    [ ГОСТ 18311-80]

    EN

    single-phase equipment
    equipment which is connected between one line conductor and the neutral conductor
    NOTE - This includes equipment in which separate loads are connected from one or more line conductors to the neutral conductor
    [IEC 61000-3-12, ed. 1.0 (2004-11)]

    FR

    matériel monophasé
    matériel connecté entre un conducteur de phase et le conducteur de neutre
    NOTE - Cela inclut les appareils dans lesquels des charges distinctes sont connectées entre un ou plusieurs conducteurs de phase et le conducteur de neutre.
    [IEC 61000-3-12, ed. 1.0 (2004-11)]

    Тематики

    • аппарат, изделие, устройство...

    Близкие понятия

    Синонимы

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > matériel monophasé

  • 2 tension d'isolement assignée (d'un dispositif de connexion)

    1. номинальное напряжение изоляции (соединительного устройства)

     

    напряжение по изоляции
    Напряжение, определяемое изготовителем для данного соединителя и его составных частей, с которыми соотносятся испытания на электрическую прочность изоляции, воздушные зазоры и расстояния утечки.
    [ ГОСТ Р 51323.1-99]

    номинальное напряжение изоляции (соединительного устройства)

    -
    [IEV number 442-06-39]

    EN

    rated insulation voltage, (of a connecting device)
    phase/neutral or phase/phase voltage value assigned to the connecting device by the manufacturer, this device being intended to be used in installations, the voltage supply of which does not exceed the rated insulation voltage of the connecting device itself
    NOTE – Rated insulation voltage is always understood to be between live parts and not between live parts and earth (ground).
    [IEV number 442-06-39]

    FR

    tension d'isolement assignée (d'un dispositif de connexion)
    valeur de la tension phase/neutre ou phase/phase assignée par le constructeur du dispositif de connexion, celui-ci étant prévu pour être utilisé dans des installations dont la tension d'alimentation ne dépasse pas la tension d'isolement assignée du dispositif de connexion lui-même
    NOTE – La tension d'isolement assignée est toujours comprise comme la tension entre parties sous tension et non entre parties sous tension et terre.
    [IEV number 442-06-39]

    Тематики

    EN

    • rated insulation voltage, (of a connecting device)

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > tension d'isolement assignée (d'un dispositif de connexion)

  • 3 tension assignée

    1. номинальное напряжение

     

    номинальное напряжение
    Напряжение, установленное изготовителем для прибора
    [ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]

    номинальное напряжение Uном, кВ
    Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
    [ ГОСТ Р 52726-2007]

    номинальное напряжение

    Un
    Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    rated voltage
    voltage assigned to the appliance by the manufacturer
    [IEC 60335-1, ed. 4.0 (2001-05)]

    rated voltage
    quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    rated voltage
    input or output supply voltage for which equipment is designed or specified
    [IEC 88528-11, ed. 1.0 (2004-03)]

    rated voltage
    specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
    NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    rated voltage
    the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
    NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    rated voltage
    reference voltage for which the cable is designed, and which serves to define the electrical tests
    NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
    Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
    U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
    In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
    This condition applies both to the value Uo and to the value U.
    In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
    NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
    [IEC 60245-1, ed. 4.0 (2003-12)]

    rated voltage
    highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
    [IEC 60800, ed. 3.0 (2009-07)]

    rated voltage
    the r.m.s. line-to-line voltage under rated conditions
    Primary side of input transformer: ULN
    Converter input: UVN
    Converter output: UaN
    Motor voltage: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    rated voltage
    input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
    [IEC 62040-1, ed. 1.0 (2008-06)]

    nominal voltage, Un
    voltage by which a system is designated or identified
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension assignée
    tension attribuée à l'appareil par le fabricant
    [IEC 60335-1, ed. 4.0 (2001-05)]

    tension nominale
    tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    tension assignée
    tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
    NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    tension assignée
    valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
    NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    tension assignée
    tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
    NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
    Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
    U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
    Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
    Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
    Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
    NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
    [IEC 60245-1, ed. 4.0 (2003-12)]

    tension assignée
    tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
    [IEC 60800, ed. 3.0 (2009-07)]

    tension assignée
    valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
    Primaire du transformateur d’entrée: ULN
    Entrée du convertisseur: UVN
    Sortie du convertisseur: UaN
    Moteur: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    tension assignée
    tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
    [IEC 62040-1, ed. 1.0 (2008-06)]

    tension nominale, Un
    tension par laquelle un réseau est désigné ou identifié
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Un

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > tension assignée

  • 4 tension nominale

    1. номинальное напряжение конденсатора
    2. номинальное напряжение

     

    номинальное напряжение
    Напряжение, установленное изготовителем для прибора
    [ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]

    номинальное напряжение Uном, кВ
    Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
    [ ГОСТ Р 52726-2007]

    номинальное напряжение

    Un
    Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    rated voltage
    voltage assigned to the appliance by the manufacturer
    [IEC 60335-1, ed. 4.0 (2001-05)]

    rated voltage
    quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    rated voltage
    input or output supply voltage for which equipment is designed or specified
    [IEC 88528-11, ed. 1.0 (2004-03)]

    rated voltage
    specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
    NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    rated voltage
    the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
    NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    rated voltage
    reference voltage for which the cable is designed, and which serves to define the electrical tests
    NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
    Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
    U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
    In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
    This condition applies both to the value Uo and to the value U.
    In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
    NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
    [IEC 60245-1, ed. 4.0 (2003-12)]

    rated voltage
    highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
    [IEC 60800, ed. 3.0 (2009-07)]

    rated voltage
    the r.m.s. line-to-line voltage under rated conditions
    Primary side of input transformer: ULN
    Converter input: UVN
    Converter output: UaN
    Motor voltage: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    rated voltage
    input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
    [IEC 62040-1, ed. 1.0 (2008-06)]

    nominal voltage, Un
    voltage by which a system is designated or identified
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension assignée
    tension attribuée à l'appareil par le fabricant
    [IEC 60335-1, ed. 4.0 (2001-05)]

    tension nominale
    tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    tension assignée
    tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
    NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    tension assignée
    valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
    NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    tension assignée
    tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
    NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
    Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
    U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
    Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
    Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
    Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
    NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
    [IEC 60245-1, ed. 4.0 (2003-12)]

    tension assignée
    tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
    [IEC 60800, ed. 3.0 (2009-07)]

    tension assignée
    valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
    Primaire du transformateur d’entrée: ULN
    Entrée du convertisseur: UVN
    Sortie du convertisseur: UaN
    Moteur: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    tension assignée
    tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
    [IEC 62040-1, ed. 1.0 (2008-06)]

    tension nominale, Un
    tension par laquelle un réseau est désigné ou identifié
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Un

    EN

    FR

     

    номинальное напряжение конденсатора
    Максимальное напряжение, при котором конденсатор может работать в течение минимальной наработки в условиях, указанных в нормативно-технической документации
    [ ГОСТ 21415-75]

    номинальное напряжение конденсатора
    Действующее значение синусоидального переменного напряжения при номинальной частоте, на которое рассчитан конденсатор. Номинальное напряжение многофазного конденсатора - значение напряжения между выводами.
    [ ГОСТ 1282-88]

    Тематики

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > tension nominale

  • 5 Un

    1. номинальное напряжение

     

    номинальное напряжение
    Напряжение, установленное изготовителем для прибора
    [ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]

    номинальное напряжение Uном, кВ
    Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
    [ ГОСТ Р 52726-2007]

    номинальное напряжение

    Un
    Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    rated voltage
    voltage assigned to the appliance by the manufacturer
    [IEC 60335-1, ed. 4.0 (2001-05)]

    rated voltage
    quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    rated voltage
    input or output supply voltage for which equipment is designed or specified
    [IEC 88528-11, ed. 1.0 (2004-03)]

    rated voltage
    specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
    NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    rated voltage
    the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
    NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    rated voltage
    reference voltage for which the cable is designed, and which serves to define the electrical tests
    NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
    Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
    U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
    In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
    This condition applies both to the value Uo and to the value U.
    In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
    NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
    [IEC 60245-1, ed. 4.0 (2003-12)]

    rated voltage
    highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
    [IEC 60800, ed. 3.0 (2009-07)]

    rated voltage
    the r.m.s. line-to-line voltage under rated conditions
    Primary side of input transformer: ULN
    Converter input: UVN
    Converter output: UaN
    Motor voltage: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    rated voltage
    input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
    [IEC 62040-1, ed. 1.0 (2008-06)]

    nominal voltage, Un
    voltage by which a system is designated or identified
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension assignée
    tension attribuée à l'appareil par le fabricant
    [IEC 60335-1, ed. 4.0 (2001-05)]

    tension nominale
    tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    tension assignée
    tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
    NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    tension assignée
    valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
    NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    tension assignée
    tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
    NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
    Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
    U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
    Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
    Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
    Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
    NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
    [IEC 60245-1, ed. 4.0 (2003-12)]

    tension assignée
    tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
    [IEC 60800, ed. 3.0 (2009-07)]

    tension assignée
    valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
    Primaire du transformateur d’entrée: ULN
    Entrée du convertisseur: UVN
    Sortie du convertisseur: UaN
    Moteur: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    tension assignée
    tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
    [IEC 62040-1, ed. 1.0 (2008-06)]

    tension nominale, Un
    tension par laquelle un réseau est désigné ou identifié
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Un

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > Un

  • 6 disjoncteur unipolaire

    1. однополюсный автоматический выключатель

     

    однополюсный автоматический выключатель
    -

    EN

    single-pole circuit-breaker circuit-breaker with one electrically separated conducting path for the main circuit suitable for use in a single phase circuit
    NOTE The construction arrangement of this device is in principle identical to one phase of a three-phase circuit-breaker.
    [IEC 62505-1, ed. 1.0 (2009-03)]

    FR

    disjoncteur unipolaire disjoncteur, constitué d'un circuit principal conducteur, électriquement séparé, destiné à un usage dans un circuit monophasé
    NOTE La disposition constructive de cet appareil est en principe identique à une phase d'un disjoncteur triphasé.
    [IEC 62505-1, ed. 1.0 (2009-03)]

    Франко-русский словарь нормативно-технической терминологии > disjoncteur unipolaire

  • 7 déphaseur

    1. фазовращатель

     

    фазовращатель
    Часть вихретокового прибора, которая поворачивает изображение комплексной плоскости
    [Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]

    фазовращатель

    -
    [IEV number 151-13-47]

    EN

    phase shifter
    device which produces specified phase differences between input and output sinusoidal quantities without changing the other characteristics
    Source: 702-09-16 MOD
    [IEV number 151-13-47]

    FR

    déphaseur, m
    dispositif qui produit des déphasages spécifiés entre grandeurs sinusoïdales d'entrée et de sortie sans modifier les autres caractéristiques
    Source: 702-09-16 MOD
    [IEV number 151-13-47]

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > déphaseur

  • 8 disjoncteur à fusibles incorporés

    1. автоматический выключатель со встроенными плавкими предохранителями

     

    автоматический выключатель со встроенными плавкими предохранителями
    Аппарат, состоящий из выключателя и плавких предохранителей, по одному предохранителю в каждом полюсе выключателя, предназначенному для присоединения к фазному проводнику.
    [ ГОСТ 50030.2-99]

    EN

    integrally fused circuit-breaker
    a combination, in a single device, of a circuit-breaker and fuses, one fuse being placed in series with each pole of the circuit-breaker intended to be connected to a phase conductor
    [IEV number    441-14-22]

    FR

    disjoncteur à fusibles incorporés
    combinaison en un seul appareil d'un disjoncteur et de fusibles, un fusible étant placé en série avec chaque pôle du disjoncteur destiné à être relié à un conducteur de phase
    [IEV number    441-14-22]

    Тематики

    Классификация

    >>>

    Обобщающие термины

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > disjoncteur à fusibles incorporés

  • 9 disjoncteur bipolaire

    1. двухполюсный автоматический выключатель

     

    двухполюсный автоматический выключатель
    -

    EN

    two-pole circuit-breaker
    circuit-breaker with two independent electrically separated conducting paths for the main circuit
    NOTE 1 The two paths may be connected in series for use in a single phase circuit where the establishment and the seperation of the two paths are simultaneous.
    NOTE 2 The construction arrangement of this device is in principle identical to two phases of a three phase circuit-breaker.
    [IEC 62505-1, ed. 1.0 (2009-03)]

    FR

    disjoncteur bipolaire
    disjoncteur constitué de deux circuits principaux indépendants conducteurs, électriquement séparés
    NOTE 1 Les deux pôles peuvent être connectés en série pour une utilisation dans un circuit monophasé où l'établissement et la coupure des deux circuits sont simultanés.
    NOTE 2 La disposition constructive de cet appareil est en principe identique à deux phases d'un disjoncteur triphasé.
    [IEC 62505-1, ed. 1.0 (2009-03)]

    Франко-русский словарь нормативно-технической терминологии > disjoncteur bipolaire

  • 10 T.T.R.

    1. переходное восстанавливающееся напряжение

     

    переходное восстанавливающееся напряжение
    ПВН

    Восстанавливающееся напряжение в течение времени, когда оно имеет заметно выраженный переходный характер. Оно может быть колебательным или апериодическим или их комбинацией, в зависимости от характеристик цепи и выключателя, отражает также смещение напряжения нейтрали многофазной цепи.
    ПВН в трехфазных цепях, если не оговорено иное, - это напряжение между выводами первого гасящего полюса, так как это напряжение обычно выше, чем на каждом из двух других полюсов.
    [ ГОСТ Р 52565-2006]

    переходное восстанавливающееся напряжение
    ПВН

    Восстанавливающееся напряжение в период времени, когда оно имеет заметно выраженный переходный характер.
    Примечания
    1 Переходное восстанавливающееся напряжение может быть колебательным или неколебательным или их комбинацией в зависимости от характеристик цепи и коммутационного аппарата. Оно отражает также смещение напряжения нейтрали многофазной цепи.
    2 Если не оговорено иначе, переходное восстанавливающееся напряжение в трехфазных цепях представляет собой напряжение между выводами первого отключающего полюса, так как это напряжение обычно более высокое, чем то, которое появляется между выводами каждого из двух других полюсов
    [ ГОСТ Р 52726-2007]

    восстанавливающееся напряжение
    1)
    Напряжение в период, когда оно носит в значительной степени переходный характер.
    Примечание. Переходное напряжение может быть колебательным или неколебательным, или носить смешанный характер в зависимости от характеристик цепи, коммутационного аппарата или плавкого предохранителя. Сюда относится и сдвиг напряжения нейтрали многофазной цепи.
    МЭК 60050(441-17-26)
    [ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
    1)  Должно быть переходное восстанавливающееся напряжение
    [Интент]

    восстанавливающееся напряжение 1)
    Напряжение в период, когда оно носит в значительной степени переходный характер.
    Примечания
    1 Это переходное напряжение может быть колебательным или неколебательным, или их комбинацией, в зависимости от характеристик цепи и выключателя. При этом учитывают сдвиг напряжения нейтрали многофазной цепи.
    2 Восстанавливающееся напряжение в трехфазных цепях в отсутствие других указаний — это напряжение между выводами первого полюса, отключающего ток, поскольку оно, как правило, выше, чем между выводами каждого из двух других полюсов
    (МЭС 441-17-26)
    [ ГОСТ Р 50345-99( МЭК 60898-95)]
    1)  Должно быть переходное восстанавливающееся напряжение
    [Интент]

    EN

    transient recovery voltage
    T.R.V. (abbreviation)
    the recovery voltage during the time in which it has a significant transient character
    NOTE 1 – The transient recovery voltage may be oscillatory or non-oscillatory or a combination of these depending on the characteristics of the circuit and the switching device. It includes the voltage shift of the neutral of a polyphase circuit.
    NOTE 2 – The transient recovery voltages in three-phase circuits is, unless otherwise stated, that across the first pole to clear, because this voltage is generally higher than that which appears across each of the other two poles.
    [IEV number 441-17-26 ]

    FR

    tension transitoire de rétablissement
    T.T.R. (abréviation)
    tension de rétablissement pendant le temps où elle présente un caractère transitoire appréciable
    NOTE 1 – La tension transitoire de rétablissement peut être oscillatoire ou non oscillatoire ou être une combinaison de celles-ci selon les caractéristiques du circuit et de l'appareil de connexion. Elle tient compte de la variation du potentiel du point neutre du circuit polyphasé.
    NOTE 2 – Sauf spécification contraire, la tension transitoire de rétablissement pour les circuits triphasés est la tension aux bornes du premier pôle qui coupe, car cette tension est généralement plus élevée que celle qui apparaît aux bornes de chacun des deux autres pôles.
    [IEV number 441-17-26 ]

    Тематики

    • выключатель, переключатель
    • высоковольтный аппарат, оборудование...

    Синонимы

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > T.T.R.

  • 11 tension transitoire de rétablissement

    1. переходное восстанавливающееся напряжение

     

    переходное восстанавливающееся напряжение
    ПВН

    Восстанавливающееся напряжение в течение времени, когда оно имеет заметно выраженный переходный характер. Оно может быть колебательным или апериодическим или их комбинацией, в зависимости от характеристик цепи и выключателя, отражает также смещение напряжения нейтрали многофазной цепи.
    ПВН в трехфазных цепях, если не оговорено иное, - это напряжение между выводами первого гасящего полюса, так как это напряжение обычно выше, чем на каждом из двух других полюсов.
    [ ГОСТ Р 52565-2006]

    переходное восстанавливающееся напряжение
    ПВН

    Восстанавливающееся напряжение в период времени, когда оно имеет заметно выраженный переходный характер.
    Примечания
    1 Переходное восстанавливающееся напряжение может быть колебательным или неколебательным или их комбинацией в зависимости от характеристик цепи и коммутационного аппарата. Оно отражает также смещение напряжения нейтрали многофазной цепи.
    2 Если не оговорено иначе, переходное восстанавливающееся напряжение в трехфазных цепях представляет собой напряжение между выводами первого отключающего полюса, так как это напряжение обычно более высокое, чем то, которое появляется между выводами каждого из двух других полюсов
    [ ГОСТ Р 52726-2007]

    восстанавливающееся напряжение
    1)
    Напряжение в период, когда оно носит в значительной степени переходный характер.
    Примечание. Переходное напряжение может быть колебательным или неколебательным, или носить смешанный характер в зависимости от характеристик цепи, коммутационного аппарата или плавкого предохранителя. Сюда относится и сдвиг напряжения нейтрали многофазной цепи.
    МЭК 60050(441-17-26)
    [ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
    1)  Должно быть переходное восстанавливающееся напряжение
    [Интент]

    восстанавливающееся напряжение 1)
    Напряжение в период, когда оно носит в значительной степени переходный характер.
    Примечания
    1 Это переходное напряжение может быть колебательным или неколебательным, или их комбинацией, в зависимости от характеристик цепи и выключателя. При этом учитывают сдвиг напряжения нейтрали многофазной цепи.
    2 Восстанавливающееся напряжение в трехфазных цепях в отсутствие других указаний — это напряжение между выводами первого полюса, отключающего ток, поскольку оно, как правило, выше, чем между выводами каждого из двух других полюсов
    (МЭС 441-17-26)
    [ ГОСТ Р 50345-99( МЭК 60898-95)]
    1)  Должно быть переходное восстанавливающееся напряжение
    [Интент]

    EN

    transient recovery voltage
    T.R.V. (abbreviation)
    the recovery voltage during the time in which it has a significant transient character
    NOTE 1 – The transient recovery voltage may be oscillatory or non-oscillatory or a combination of these depending on the characteristics of the circuit and the switching device. It includes the voltage shift of the neutral of a polyphase circuit.
    NOTE 2 – The transient recovery voltages in three-phase circuits is, unless otherwise stated, that across the first pole to clear, because this voltage is generally higher than that which appears across each of the other two poles.
    [IEV number 441-17-26 ]

    FR

    tension transitoire de rétablissement
    T.T.R. (abréviation)
    tension de rétablissement pendant le temps où elle présente un caractère transitoire appréciable
    NOTE 1 – La tension transitoire de rétablissement peut être oscillatoire ou non oscillatoire ou être une combinaison de celles-ci selon les caractéristiques du circuit et de l'appareil de connexion. Elle tient compte de la variation du potentiel du point neutre du circuit polyphasé.
    NOTE 2 – Sauf spécification contraire, la tension transitoire de rétablissement pour les circuits triphasés est la tension aux bornes du premier pôle qui coupe, car cette tension est généralement plus élevée que celle qui apparaît aux bornes de chacun des deux autres pôles.
    [IEV number 441-17-26 ]

    Тематики

    • выключатель, переключатель
    • высоковольтный аппарат, оборудование...

    Синонимы

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > tension transitoire de rétablissement

  • 12 réseau à neutre impédant

    1. система с нейтралью, заземленной через сопротивление

     

    система с нейтралью, заземленной через сопротивление
    Система, в которой по крайней мере одна нейтральная точка заземлена через устройство, имеющее сопротивление, предназначенное для ограничения тока короткого замыкания между фазой и землей.
    [ ГОСТ Р МЭК 60050-195-2005]

    EN

    impedance earthed neutral system
    system in which at least one neutral point is earthed through a device having an impedance designed to limit the line-to-earth short-circuit current
    [IEV number 195-04-08]

    FR

    réseau à neutre impédant
    réseau dont au moins un point neutre est mis à la terre par l’intermédiaire d’un dispositif présentant une impédance conçue pour limiter le courant de court-circuit phase-terre
    [IEV number 195-04-08]

    Тематики

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > réseau à neutre impédant

См. также в других словарях:

  • Phase fired controllers — Phase control (PFC), also called phase cutting, is a method of pulse width modulation (PWM) for power limiting, applied to AC voltages. It works by modulating a thyristor, SCR, triac, thyratron, or other such gated diode like devices into and out …   Wikipedia

  • Phase response — is the relationship between the phase of a sinusoidal input and the output signal passing through any device which accepts input and produces an output signal such as an amplifier or a filter.Amplifiers, filters and other devices are often… …   Wikipedia

  • Phase splitter — (Elec.) A device by which a single phase current is split into two or more currents differing in phase. It is used in starting single phase induction motors. [Webster 1913 Suppl.] …   The Collaborative International Dictionary of English

  • Phase meter — Phase meter, or Phasemeter Phase me ter, n. (Elec.) A device for measuring the difference in phase of two alternating currents of electromotive forces. [Webster 1913 Suppl.] …   The Collaborative International Dictionary of English

  • Phase-change memory — Computer memory types Volatile RAM DRAM (e.g., DDR SDRAM) SRAM In development T RAM Z RAM TTRAM Historical Delay line memory Selectron tube Williams tube Non volatile …   Wikipedia

  • Device Forts — Deal Castle in Kent was built between 1539 and 1540. The Device Forts, also known as Henrician Castles, are a series of artillery fortifications built to defend the southern coast of England by Henry VIII. After his divorce of Catherine of Aragon …   Wikipedia

  • Phase-locked loop — PLL redirects here. For other uses, see PLL (disambiguation). A phase locked loop or phase lock loop (PLL) is a control system that generates an output signal whose phase is related to the phase of an input reference signal. It is an electronic… …   Wikipedia

  • phase-shifting device — fazės keitiklis statusas T sritis automatika atitikmenys: angl. phase changer; phase converter; phase shifter; phase shifting device vok. Phasendreher, m; Phasenschieber, m; Phasenumformer, m rus. фазовращатель, m; фазовый преобразователь, m;… …   Automatikos terminų žodynas

  • Phase-shift keying — Passband modulation v · d · e Analog modulation AM · …   Wikipedia

  • Phase detector — A phase detector is a frequency mixer or analog multiplier circuit that generates a voltage signal which represents the difference in phase between two signal inputs. It is an essential element of the phase locked loop (PLL).Detecting phase… …   Wikipedia

  • Phase converter — A phase converter is a device that converts power provided as single or multiple phases to a different number of phases.The majority of phase converters are used to produce three phase electrical power from a single phase source, thus allowing… …   Wikipedia

Поделиться ссылкой на выделенное

Прямая ссылка:
Нажмите правой клавишей мыши и выберите «Копировать ссылку»