-
41 function Bw
функция Bw (реле времени)
Формирование импульса при подаче, а также при снятии напряжения с управляющего входа
[Интент]EN
function Bw
Double interval relay with control signal
[Schneider Electric]
function Bw
Pulse output (adjustable)
[Crouzet]Параллельные тексты EN-RU
U - Напряжение питания реле времени
С - Управляющий вход (положение контакта, коммутирующего управляющий вход)
G - Вход прерывания (положение контакта, коммутирующего вход прерывания)
R - контактный или полупроводниковый выход релеOn closing and opening of control contact C, the output R closes for the duration of the timing period T.
[Schneider Electric]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Bw
-
42 function C
функция C (реле времени)
Срабатывание при подаче напряжения на управляющий вход и задержка возврата при снятии напряжения с управляющего входа.
[Интент]EN
function C
Off-delay relay with control signal
[Schneider Electric]
function C
Timing after impulse
Delay OFF (with constant supply
[Crouzet]Параллельные тексты EN-RU
U - Напряжение питания реле времени
С - Управляющий вход (положение контакта, коммутирующего управляющий вход)
G - Вход прерывания (положение контакта, коммутирующего вход прерывания)
R - контактный или полупроводниковый выход релеAfter power-up and closing of the control contact C, the output R closes.
When control contact C re-opens, timing T starts.
At the end of the timing period, output(s) R revert(s) to its/their initial state.
[Schneider Electric]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function C
-
43 output impedance
- полное сопротивление выходного электрода
- выходное полное сопротивление пьезоэлектрического (электромеханического) фильтра
- выходное полное сопротивление
выходное полное сопротивление
-
[IEV number 312-06-19]EN
output impedance
impedance of the output circuit measured between the output terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the output circuit is such that the instantaneous value of the current flowing into the output terminals is a non-linear function of the instantaneous value of the output voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual output circuit, is sometimes called the "equivalent output impedance".
[IEV number 312-06-19]FR
impédance du circuit de sortie
impédance du circuit de sortie entre les bornes de sortie dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit de sortie est tel que la valeur instantanée du courant traversant les bornes de sortie est une fonction non linéaire de la valeur instantanée de la tension de sortie dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit de sortie réel, est parfois appelée "impédance équivalente de sortie".
[IEV number 312-06-19]Тематики
- измерение электр. величин в целом
EN
DE
FR
выходное полное сопротивление пьезоэлектрического (электромеханического) фильтра (Zвых, Zout)
Комплексное сопротивление, которое представляет собой пьезоэлектрический (электромеханический) фильтр нагрузочного полного для выходного сопротивления, когда он подключен к входному нагрузочному полному сопротивлению.
[ ГОСТ 18670-84]Тематики
EN
FR
полное сопротивление выходного электрода
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > output impedance
-
44 output efficiency
эк. эффективность по выпуску* (состояние, при котором фирма получает максимальное количество продукта из затрачиваемых ресурсов)Ant:See: -
45 output inefficiency
эк. неэффективность по выпуску* (состояние, при котором фирма может получить из затрачиваемых ресурсов большее количество продукта, чем то, которое реально получает получает)Ant:See: -
46 output transfer function
передаточная функция от входа к выходу (системы)
—
[Я.Н.Лугинский, М.С.Фези-Жилинская, Ю.С.Кабиров. Англо-русский словарь по электротехнике и электроэнергетике, Москва, 1999 г.]Тематики
- электротехника, основные понятия
EN
Англо-русский словарь нормативно-технической терминологии > output transfer function
-
47 function Di
функция Di (реле времени)
Периодическая последовательность импульсов с равными длительностями паузы и импульса, начинающаяся с наличия импульса
[Интент]EN
function Di
Symmetrical flasher relay (starting pulse on)
[Schneider Electric]
function Di
Flip-flop
[Crouzet]Параллельные тексты EN-RU
Function Di
Symmetrical flasher relay
Repetitive cycle with two timing periods T of equal duration, with output(s) R changing state at the end of each timing period T.
[Schneider Electric]Функция Di
Периодическая последовательность импульсов с равными длительностями паузы и импульса
Периодическая последовательность с двумя выдержками времени T равной длительности, выход(ы) R меняе(ю)т свое состояние в конце каждой выдержки времени T.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Di
48 function Ac
функция Ac (реле времени)
- Отсчет двух выдержек времени: после подачи и после снятия напряжения с управляющего входа.
- Задержка срабатывания и задержка возврата реле после подачи и после снятия напряжения с управляющего входа.
[Интент]EN
function Ac
Timing after closing and opening of control contact
[Crouzed]
function Ac
On-delay and off-delay relay with control signal
[Schneider Electric]
Рис. CrouzedПараллельные тексты EN-RU
After energisation, closure of the control contact causes the timing period T to commence and output relay R (or the load) changes state at the end of this interval.
When contact C (Y1) opens, relay R resets after a second timing period T.
[Crouzed]После подачи питания на реле и последующего замыкания контакта в цепи управляющего входа выполняется отсчет выдержки времени Т, по окончании которого выходное реле R (или нагрузка) изменяет свое состояние.
После размыкания контакта С еще раз отсчитывается выдержка времени Т, по окончании которой реле R возвращается в исходное состояние.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Ac
49 function B
функция B (реле времени)
Формирование импульса при подаче напряжения на управляющий вход.
[Интент]EN
function B
Interval relay with control signal
[Schneider Electric]
function B
Timing on impulse one shot. On pulse (with constant supply)
[Crouzet]Параллельные тексты EN-RU
U - Напряжение питания реле времени
С - Управляющий вход (положение контакта, коммутирующего управляющий вход)
G - Вход прерывания (положение контакта, коммутирующего вход прерывания)
R - контактный или полупроводниковый выход релеAfter power-up, pulsing or maintaining control contact C starts the timing T.
The output R closes for the duration of the timing period T then reverts to its initial state.
[Schneider Electric]Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function B
50 function Ab
функция Ab (реле времени)
Один импульс после задержки, отсчитываемой от подачи питания
[Интент]EN
function Ab
one-shot cycle
[Crouzed]Параллельные тексты EN-RU
The output changes states at the end of the set time T1, for a period T2.
[Crouzed]Выход реле изменяет свое состояние по окончании выдержки времени Т1, отсчитываемой от момента подачи питания на реле и сохраняет его в течение времени Т2.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Ab
51 function Ak
функция Ak (реле времени)
Независимые задержки срабатывания и возврата реле, отсчитываемые от момента подачи и снятия напряжения с управляющего входа соответственно.
[Интент]EN
function Ak
Asymmetrical On-delay and Off-delay with external control
[Schneider Electric]Параллельные тексты EN-RU
Рис. Schneider Electric
U - Напряжение питания реле времени
С - Управляющий вход (положение контакта, коммутирующего управляющий вход)
G - Вход прерывания (положение контакта, коммутирующего вход прерывания)
R - контактный или полупроводниковый выход релеAfter power-up, closing of the control contact C causes the timing period T to start (timing can be interrupted by operating the Gate control contact G).
At the end of this timing period, the relay closes.
When control contact C re-opens, the timing T starts.
At the end of this timing period T, the output reverts to its initial position (timing can be interrupted by operating the Gate control contact G).
[Schneider Electric]После подачи питания на реле времени, а затем напряжения на управляющий вход С, начинается отсчет выдержки времени Т (отсчет может прерываться подачей напряжения на вход прерывания G).
По окончании выдержки времени контакт реле замыкается.
После снятия напряжения с управляющего входа С возобновляется отсчет выдержки времени Т.
По окончании выдержки времени контакт реле размыкается (реле времени возвращается в исходное положение). Отсчет выдержки времени может прерываться подачей напряжения на вход прерывания G.
[Перевод Интент]
Тематики
EN
Англо-русский словарь нормативно-технической терминологии > function Ak
52 output transfer function US
переходная функция замкнутой системы; передаточная функция замкнутой системы; см. также closed-loop transfer functionАнгло-русский словарь промышленной и научной лексики > output transfer function US
53 function
"A piece of code that operates as a single logical unit. A function is called by name, accepts optional input parameters, and returns a status and optional output parameters. Many programming languages support functions."54 output event
1) Программирование: выходное событие (см. IEC 61499-1, Robert W. Lewis: Modelling control systems using IEC 61499. Applying function blocks to distributed systems), событие на выходе (функционального блока)2) SAP.тех. событие вывода55 output events
Программирование: выходные события (см. IEC 61499-1, Robert W. Lewis: Modelling control systems using IEC 61499. Applying function blocks to distributed systems)56 function of random variable
stock variable — переменная, характеризующая величину запаса
random variable — случайная величина; случайная переменная
English-Russian big polytechnic dictionary > function of random variable
57 function block output interface
Программирование: выходной интерфейс функционального блокаУниверсальный англо-русский словарь > function block output interface
58 function block output parameter
Программирование: выходной параметр функционального блокаУниверсальный англо-русский словарь > function block output parameter
59 output transfer function
Электротехника: передаточная функция от входа к выходу (системы)Универсальный англо-русский словарь > output transfer function
60 output transfer function
• suljetun piirin siirtofunktioСтраницыСм. также в других словарях:
Output-based aid — (OBA) refers to development aid strategies that link the delivery of public services in developing countries to targeted performance related subsidies. OBA subsidies are offered in transport construction, education, water and sanitation systems,… … Wikipedia
Function — may refer to:* Function (biology), explaining why a feature survived selection * Function (mathematics), an abstract entity that associates an input to a corresponding output according to some rule * Function (engineering), related to the… … Wikipedia
Function overloading — or method overloading is a feature found in various programming languages such as Ada, C#, VB.NET, C++, D and Java that allows the creation of several methods with the same name which differ from each other in terms of the type of the input and… … Wikipedia
Function (mathematics) — f(x) redirects here. For the band, see f(x) (band). Graph of example function, In mathematics, a function associates one quantity, the a … Wikipedia
Function generator — [ http://www.agilent.com/u2761a U2761A] USB Modular Function Generator from Agilent Technologies] A function generator is a piece of electronic test equipment or software used to generate electrical waveforms. These waveforms can be either… … Wikipedia
Function block diagram — A function block diagram is a diagram, that describes a function between input variables and output variables. A function is described as a set of elementary blocks. Input and output variables are connected to blocks by connection lines. An… … Wikipedia
function — /fungk sheuhn/, n. 1. the kind of action or activity proper to a person, thing, or institution; the purpose for which something is designed or exists; role. 2. any ceremonious public or social gathering or occasion. 3. a factor related to or… … Universalium
Function composition — For function composition in computer science, see function composition (computer science). g ∘ f, the composition of f and g. For example, (g ∘ f)(c) = #. In mathematics, function composition is the application of one function to the resul … Wikipedia
Function-Point-Verfahren — Das Function Point Verfahren (auch Analyse oder Methode, kurz FPA) dient zur Bewertung des fachlich funktionalen Umfangs eines Informationstechnischen Systems, im Folgenden als Anwendung bezeichnet. Das Ergebnis einer Function Point Bewertung… … Deutsch Wikipedia
Output elasticity — In economics, output elasticity is the percentage change of output (GDP or production of a single firm) divided by the percentage change of an input. It is sometimes called partial output elasticity to clarify that it refers to the change of only … Wikipedia
Function prologue — In assembly language programming, the function prologue is a few lines of code which appear at the beginning of a function, which prepare the stack and registers for use within the function. Similarly, the function epilogue appears at the end of… … Wikipedia
Перевод: со всех языков на все языки
со всех языков на все языки- Со всех языков на:
- Все языки
- Со всех языков на:
- Все языки
- Албанский
- Английский
- Арабский
- Болгарский
- Испанский
- Казахский
- Немецкий
- Нидерландский
- Русский
- Словацкий
- Украинский
- Финский
- Французский
- Хорватский