-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
Cooling tower — Natural draft wet cooling hyperboloid towers at Didcot Power Station, UK … Wikipedia
One Canada Square — A view of One Canada Square, the second tallest building in the United Kingdom. Record height Tallest in the United … Wikipedia
Cooling Out — is a technique composed of an informal set of practices used by colleges, especially two year, junior, and community colleges, to handle students whose lack of academic ability prevents them from achieving the educational goals they have… … Wikipedia
One World Trade Center — Freedom Tower redirects here. For other uses, see Freedom Tower (disambiguation). For the building complex destroyed in the September 11 attacks, see World Trade Center. For the specific WTC building formerly known as One World Trade Center, see… … Wikipedia
Cortical cooling — Neuroscientists generate various studies to help explain many of the complex connections and functions of the brain. Most studies utilize animal models that have varying degrees of comparison to the human brain; for example, small rodents are… … Wikipedia
Computer cooling — An OEM AMD heatsink mounted onto a motherboard. Computer cooling is required to remove the waste heat produced by computer components, to keep components within their safe operating temperature limits. Various cooling methods help to improve… … Wikipedia
Engine cooling — is cooling an engine, typically using either air or liquid.OverviewHeat engines generate mechanical power by extracting energy from heat flows, much as a water wheel extracts mechanical power from a flow of mass falling through a distance.… … Wikipedia
Doppler cooling — is a mechanism that can be used to trap and cool atoms. The term is sometimes used synonymously with laser cooling, though laser cooling includes other techniques. Contents 1 History 2 Brief Explanation 3 Detailed Explanation … Wikipedia
Passive cooling — refers to technologies or design features used to cool buildings without power consumption, such as those technologies discussed in the Passive house project.Passive coolingThe term passive implies that energy consuming mechanical components like … Wikipedia
Radiator (engine cooling) — For other uses, see Radiator (disambiguation). A typical engine coolant radiator used in an automobile Radiators are used for cooling internal combustion engines, mainly in automobiles but also in piston engined aircraft, railway locomotives,… … Wikipedia
Global cooling — in general can refer to an overall cooling of the Earth. In this article it refers primarily to a conjecture during the 1970s of imminent cooling of the Earth s surface and atmosphere along with a posited commencement of glaciation. This… … Wikipedia
