-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
Power semiconductor device — Power semiconductor devices are semiconductor devices used as switches or rectifiers in power electronic circuits (switch mode power supplies for example). They are also called power devices or when used in integrated circuits, called power… … Wikipedia
Power management — is a feature of some electrical appliances, especially copiers, computers and computer peripherals such as monitors and printers, that turns off the power or switches the system to a low power state when inactive. One power management standard… … Wikipedia
Power MOSFET — A Power MOSFET is a specific type of Metal Oxide Semiconductor Field Effect Transistor (MOSFET) designed to handle large power. Compared to the other power semiconductor devices (IGBT, Thyristor...), its main advantages are high commutation speed … Wikipedia
Power optimization (EDA) — Power optimization refers to the use of electronic design automation tools to optimize (reduce) the power consumption of a digital design, while preserving the functionality.Introduction and historyThe increasing speed and complexity of today’s… … Wikipedia
Low-power electronics — means that the consumption of electric power is deliberately low, e.g. notebook processors. Electronics The density and speed of integrated circuit computing elements has increased roughly exponentially for a period of several decades, following… … Wikipedia
Thermal management of high power LED — With the coming of energy saving era, high power light emitting diodes (LEDs) are promising to replace other technologies such as incandescent and fluorescent bulbs in signaling, solid state lighting, and vehicle headlight applications due to… … Wikipedia
Fluctuation dissipation theorem — In statistical physics, the fluctuation dissipation theorem is a powerful tool for predicting the non equilibrium behavior of a system such as the irreversible dissipation of energy into heat from its reversible fluctuations in thermal… … Wikipedia
Tidal power — Tidal power, sometimes called tidal energy, is a form of hydropower that converts the energy of tides into electricity or other useful forms of power.Although not yet widely used, tidal power has potential for future electricity generation. Tides … Wikipedia
Nuclear power plant — This article is about electricity generation from nuclear power. For the general topic of nuclear power, see Nuclear power. A nuclear power station. The nuclear reactor is contained inside the cylindrical containment buildings to the right left… … Wikipedia
Calvert Cliffs Nuclear Power Plant — Infobox NPP Picture=Calvert Cliffs.jpg pic des=Calvert Cliffs NPP Picture des= Status=O Utility=Constellation Energy Location=Lusby, Maryland Supplier=Combustion Engineering Type=PWR Generators=Unit 1: General Electric Unit 2: Westinghouse… … Wikipedia
ГОСТ 20332-84: Тиристоры. Термины, определения и буквенные обозначения параметров — Терминология ГОСТ 20332 84: Тиристоры. Термины, определения и буквенные обозначения параметров оригинал документа: 110. Время включения тиристора E. Turn on time F. Temps d’amorcage tувкл, tвкл Интервал времени, в течение которого тиристор… … Словарь-справочник терминов нормативно-технической документации
